PCI: doc/pci: create Documentation/PCI/ and move files into it

Create Documentation/PCI/ and move PCI-related files to it.
Fix a few instances of trailing whitespace.
Update references to the new file locations.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

5 files changed, 1524 insertions, 0 deletions

diff --git a/Documentation/PCI/00-INDEX b/Documentation/PCI/00-INDEX
new file mode 100644
index 000000000000..49f43946c6b6
--- /dev/null
+++ b/Documentation/PCI/00-INDEX
@@ -0,0 +1,12 @@
+00-INDEX
+	- this file
+PCI-DMA-mapping.txt
+	- info for PCI drivers using DMA portably across all platforms
+PCIEBUS-HOWTO.txt
+	- a guide describing the PCI Express Port Bus driver
+pci-error-recovery.txt
+	- info on PCI error recovery
+pci.txt
+	- info on the PCI subsystem for device driver authors
+pcieaer-howto.txt
+	- the PCI Express Advanced Error Reporting Driver Guide HOWTO
diff --git a/Documentation/PCI/PCIEBUS-HOWTO.txt b/Documentation/PCI/PCIEBUS-HOWTO.txt
new file mode 100644
index 000000000000..9a07e38631b0
--- /dev/null
+++ b/Documentation/PCI/PCIEBUS-HOWTO.txt
@@ -0,0 +1,217 @@
+		The PCI Express Port Bus Driver Guide HOWTO
+	Tom L Nguyen tom.l.nguyen@intel.com
+			11/03/2004
+
+1. About this guide
+
+This guide describes the basics of the PCI Express Port Bus driver
+and provides information on how to enable the service drivers to
+register/unregister with the PCI Express Port Bus Driver.
+
+2. Copyright 2004 Intel Corporation
+
+3. What is the PCI Express Port Bus Driver
+
+A PCI Express Port is a logical PCI-PCI Bridge structure. There
+are two types of PCI Express Port: the Root Port and the Switch
+Port. The Root Port originates a PCI Express link from a PCI Express
+Root Complex and the Switch Port connects PCI Express links to
+internal logical PCI buses. The Switch Port, which has its secondary
+bus representing the switch's internal routing logic, is called the
+switch's Upstream Port. The switch's Downstream Port is bridging from
+switch's internal routing bus to a bus representing the downstream
+PCI Express link from the PCI Express Switch.
+
+A PCI Express Port can provide up to four distinct functions,
+referred to in this document as services, depending on its port type.
+PCI Express Port's services include native hotplug support (HP),
+power management event support (PME), advanced error reporting
+support (AER), and virtual channel support (VC). These services may
+be handled by a single complex driver or be individually distributed
+and handled by corresponding service drivers.
+
+4. Why use the PCI Express Port Bus Driver?
+
+In existing Linux kernels, the Linux Device Driver Model allows a
+physical device to be handled by only a single driver. The PCI
+Express Port is a PCI-PCI Bridge device with multiple distinct
+services. To maintain a clean and simple solution each service
+may have its own software service driver. In this case several
+service drivers will compete for a single PCI-PCI Bridge device.
+For example, if the PCI Express Root Port native hotplug service
+driver is loaded first, it claims a PCI-PCI Bridge Root Port. The
+kernel therefore does not load other service drivers for that Root
+Port. In other words, it is impossible to have multiple service
+drivers load and run on a PCI-PCI Bridge device simultaneously
+using the current driver model.
+
+To enable multiple service drivers running simultaneously requires
+having a PCI Express Port Bus driver, which manages all populated
+PCI Express Ports and distributes all provided service requests
+to the corresponding service drivers as required. Some key
+advantages of using the PCI Express Port Bus driver are listed below:
+
+	- Allow multiple service drivers to run simultaneously on
+	  a PCI-PCI Bridge Port device.
+
+	- Allow service drivers implemented in an independent
+	  staged approach.
+
+	- Allow one service driver to run on multiple PCI-PCI Bridge
+	  Port devices.
+
+	- Manage and distribute resources of a PCI-PCI Bridge Port
+	  device to requested service drivers.
+
+5. Configuring the PCI Express Port Bus Driver vs. Service Drivers
+
+5.1 Including the PCI Express Port Bus Driver Support into the Kernel
+
+Including the PCI Express Port Bus driver depends on whether the PCI
+Express support is included in the kernel config. The kernel will
+automatically include the PCI Express Port Bus driver as a kernel
+driver when the PCI Express support is enabled in the kernel.
+
+5.2 Enabling Service Driver Support
+
+PCI device drivers are implemented based on Linux Device Driver Model.
+All service drivers are PCI device drivers. As discussed above, it is
+impossible to load any service driver once the kernel has loaded the
+PCI Express Port Bus Driver. To meet the PCI Express Port Bus Driver
+Model requires some minimal changes on existing service drivers that
+imposes no impact on the functionality of existing service drivers.
+
+A service driver is required to use the two APIs shown below to
+register its service with the PCI Express Port Bus driver (see
+section 5.2.1 & 5.2.2). It is important that a service driver
+initializes the pcie_port_service_driver data structure, included in
+header file /include/linux/pcieport_if.h, before calling these APIs.
+Failure to do so will result an identity mismatch, which prevents
+the PCI Express Port Bus driver from loading a service driver.
+
+5.2.1 pcie_port_service_register
+
+int pcie_port_service_register(struct pcie_port_service_driver *new)
+
+This API replaces the Linux Driver Model's pci_module_init API. A
+service driver should always calls pcie_port_service_register at
+module init. Note that after service driver being loaded, calls
+such as pci_enable_device(dev) and pci_set_master(dev) are no longer
+necessary since these calls are executed by the PCI Port Bus driver.
+
+5.2.2 pcie_port_service_unregister
+
+void pcie_port_service_unregister(struct pcie_port_service_driver *new)
+
+pcie_port_service_unregister replaces the Linux Driver Model's
+pci_unregister_driver. It's always called by service driver when a
+module exits.
+
+5.2.3 Sample Code
+
+Below is sample service driver code to initialize the port service
+driver data structure.
+
+static struct pcie_port_service_id service_id[] = { {
+	.vendor = PCI_ANY_ID,
+	.device = PCI_ANY_ID,
+	.port_type = PCIE_RC_PORT,
+	.service_type = PCIE_PORT_SERVICE_AER,
+	}, { /* end: all zeroes */ }
+};
+
+static struct pcie_port_service_driver root_aerdrv = {
+	.name		= (char *)device_name,
+	.id_table	= &service_id[0],
+
+	.probe		= aerdrv_load,
+	.remove		= aerdrv_unload,
+
+	.suspend	= aerdrv_suspend,
+	.resume		= aerdrv_resume,
+};
+
+Below is a sample code for registering/unregistering a service
+driver.
+
+static int __init aerdrv_service_init(void)
+{
+	int retval = 0;
+
+	retval = pcie_port_service_register(&root_aerdrv);
+	if (!retval) {
+		/*
+		 * FIX ME
+		 */
+	}
+	return retval;
+}
+
+static void __exit aerdrv_service_exit(void)
+{
+	pcie_port_service_unregister(&root_aerdrv);
+}
+
+module_init(aerdrv_service_init);
+module_exit(aerdrv_service_exit);
+
+6. Possible Resource Conflicts
+
+Since all service drivers of a PCI-PCI Bridge Port device are
+allowed to run simultaneously, below lists a few of possible resource
+conflicts with proposed solutions.
+
+6.1 MSI Vector Resource
+
+The MSI capability structure enables a device software driver to call
+pci_enable_msi to request MSI based interrupts. Once MSI interrupts
+are enabled on a device, it stays in this mode until a device driver
+calls pci_disable_msi to disable MSI interrupts and revert back to
+INTx emulation mode. Since service drivers of the same PCI-PCI Bridge
+port share the same physical device, if an individual service driver
+calls pci_enable_msi/pci_disable_msi it may result unpredictable
+behavior. For example, two service drivers run simultaneously on the
+same physical Root Port. Both service drivers call pci_enable_msi to
+request MSI based interrupts. A service driver may not know whether
+any other service drivers have run on this Root Port. If either one
+of them calls pci_disable_msi, it puts the other service driver
+in a wrong interrupt mode.
+
+To avoid this situation all service drivers are not permitted to
+switch interrupt mode on its device. The PCI Express Port Bus driver
+is responsible for determining the interrupt mode and this should be
+transparent to service drivers. Service drivers need to know only
+the vector IRQ assigned to the field irq of struct pcie_device, which
+is passed in when the PCI Express Port Bus driver probes each service
+driver. Service drivers should use (struct pcie_device*)dev->irq to
+call request_irq/free_irq. In addition, the interrupt mode is stored
+in the field interrupt_mode of struct pcie_device.
+
+6.2 MSI-X Vector Resources
+
+Similar to the MSI a device driver for an MSI-X capable device can
+call pci_enable_msix to request MSI-X interrupts. All service drivers
+are not permitted to switch interrupt mode on its device. The PCI
+Express Port Bus driver is responsible for determining the interrupt
+mode and this should be transparent to service drivers. Any attempt
+by service driver to call pci_enable_msix/pci_disable_msix may
+result unpredictable behavior. Service drivers should use
+(struct pcie_device*)dev->irq and call request_irq/free_irq.
+
+6.3 PCI Memory/IO Mapped Regions
+
+Service drivers for PCI Express Power Management (PME), Advanced
+Error Reporting (AER), Hot-Plug (HP) and Virtual Channel (VC) access
+PCI configuration space on the PCI Express port. In all cases the
+registers accessed are independent of each other. This patch assumes
+that all service drivers will be well behaved and not overwrite
+other service driver's configuration settings.
+
+6.4 PCI Config Registers
+
+Each service driver runs its PCI config operations on its own
+capability structure except the PCI Express capability structure, in
+which Root Control register and Device Control register are shared
+between PME and AER. This patch assumes that all service drivers
+will be well behaved and not overwrite other service driver's
+configuration settings.
diff --git a/Documentation/PCI/pci-error-recovery.txt b/Documentation/PCI/pci-error-recovery.txt
new file mode 100644
index 000000000000..6650af432523
--- /dev/null
+++ b/Documentation/PCI/pci-error-recovery.txt
@@ -0,0 +1,396 @@
+
+                       PCI Error Recovery
+                       ------------------
+                        February 2, 2006
+
+                 Current document maintainer:
+             Linas Vepstas <linas@austin.ibm.com>
+
+
+Many PCI bus controllers are able to detect a variety of hardware
+PCI errors on the bus, such as parity errors on the data and address
+busses, as well as SERR and PERR errors.  Some of the more advanced
+chipsets are able to deal with these errors; these include PCI-E chipsets,
+and the PCI-host bridges found on IBM Power4 and Power5-based pSeries
+boxes. A typical action taken is to disconnect the affected device,
+halting all I/O to it.  The goal of a disconnection is to avoid system
+corruption; for example, to halt system memory corruption due to DMA's
+to "wild" addresses. Typically, a reconnection mechanism is also
+offered, so that the affected PCI device(s) are reset and put back
+into working condition. The reset phase requires coordination
+between the affected device drivers and the PCI controller chip.
+This document describes a generic API for notifying device drivers
+of a bus disconnection, and then performing error recovery.
+This API is currently implemented in the 2.6.16 and later kernels.
+
+Reporting and recovery is performed in several steps. First, when
+a PCI hardware error has resulted in a bus disconnect, that event
+is reported as soon as possible to all affected device drivers,
+including multiple instances of a device driver on multi-function
+cards. This allows device drivers to avoid deadlocking in spinloops,
+waiting for some i/o-space register to change, when it never will.
+It also gives the drivers a chance to defer incoming I/O as
+needed.
+
+Next, recovery is performed in several stages. Most of the complexity
+is forced by the need to handle multi-function devices, that is,
+devices that have multiple device drivers associated with them.
+In the first stage, each driver is allowed to indicate what type
+of reset it desires, the choices being a simple re-enabling of I/O
+or requesting a hard reset (a full electrical #RST of the PCI card).
+If any driver requests a full reset, that is what will be done.
+
+After a full reset and/or a re-enabling of I/O, all drivers are
+again notified, so that they may then perform any device setup/config
+that may be required.  After these have all completed, a final
+"resume normal operations" event is sent out.
+
+The biggest reason for choosing a kernel-based implementation rather
+than a user-space implementation was the need to deal with bus
+disconnects of PCI devices attached to storage media, and, in particular,
+disconnects from devices holding the root file system.  If the root
+file system is disconnected, a user-space mechanism would have to go
+through a large number of contortions to complete recovery. Almost all
+of the current Linux file systems are not tolerant of disconnection
+from/reconnection to their underlying block device. By contrast,
+bus errors are easy to manage in the device driver. Indeed, most
+device drivers already handle very similar recovery procedures;
+for example, the SCSI-generic layer already provides significant
+mechanisms for dealing with SCSI bus errors and SCSI bus resets.
+
+
+Detailed Design
+---------------
+Design and implementation details below, based on a chain of
+public email discussions with Ben Herrenschmidt, circa 5 April 2005.
+
+The error recovery API support is exposed to the driver in the form of
+a structure of function pointers pointed to by a new field in struct
+pci_driver. A driver that fails to provide the structure is "non-aware",
+and the actual recovery steps taken are platform dependent.  The
+arch/powerpc implementation will simulate a PCI hotplug remove/add.
+
+This structure has the form:
+struct pci_error_handlers
+{
+	int (*error_detected)(struct pci_dev *dev, enum pci_channel_state);
+	int (*mmio_enabled)(struct pci_dev *dev);
+	int (*link_reset)(struct pci_dev *dev);
+	int (*slot_reset)(struct pci_dev *dev);
+	void (*resume)(struct pci_dev *dev);
+};
+
+The possible channel states are:
+enum pci_channel_state {
+	pci_channel_io_normal,  /* I/O channel is in normal state */
+	pci_channel_io_frozen,  /* I/O to channel is blocked */
+	pci_channel_io_perm_failure, /* PCI card is dead */
+};
+
+Possible return values are:
+enum pci_ers_result {
+	PCI_ERS_RESULT_NONE,        /* no result/none/not supported in device driver */
+	PCI_ERS_RESULT_CAN_RECOVER, /* Device driver can recover without slot reset */
+	PCI_ERS_RESULT_NEED_RESET,  /* Device driver wants slot to be reset. */
+	PCI_ERS_RESULT_DISCONNECT,  /* Device has completely failed, is unrecoverable */
+	PCI_ERS_RESULT_RECOVERED,   /* Device driver is fully recovered and operational */
+};
+
+A driver does not have to implement all of these callbacks; however,
+if it implements any, it must implement error_detected(). If a callback
+is not implemented, the corresponding feature is considered unsupported.
+For example, if mmio_enabled() and resume() aren't there, then it
+is assumed that the driver is not doing any direct recovery and requires
+a reset. If link_reset() is not implemented, the card is assumed as
+not care about link resets. Typically a driver will want to know about
+a slot_reset().
+
+The actual steps taken by a platform to recover from a PCI error
+event will be platform-dependent, but will follow the general
+sequence described below.
+
+STEP 0: Error Event
+-------------------
+PCI bus error is detect by the PCI hardware.  On powerpc, the slot
+is isolated, in that all I/O is blocked: all reads return 0xffffffff,
+all writes are ignored.
+
+
+STEP 1: Notification
+--------------------
+Platform calls the error_detected() callback on every instance of
+every driver affected by the error.
+
+At this point, the device might not be accessible anymore, depending on
+the platform (the slot will be isolated on powerpc). The driver may
+already have "noticed" the error because of a failing I/O, but this
+is the proper "synchronization point", that is, it gives the driver
+a chance to cleanup, waiting for pending stuff (timers, whatever, etc...)
+to complete; it can take semaphores, schedule, etc... everything but
+touch the device. Within this function and after it returns, the driver
+shouldn't do any new IOs. Called in task context. This is sort of a
+"quiesce" point. See note about interrupts at the end of this doc.
+
+All drivers participating in this system must implement this call.
+The driver must return one of the following result codes:
+		- PCI_ERS_RESULT_CAN_RECOVER:
+		  Driver returns this if it thinks it might be able to recover
+		  the HW by just banging IOs or if it wants to be given
+		  a chance to extract some diagnostic information (see
+		  mmio_enable, below).
+		- PCI_ERS_RESULT_NEED_RESET:
+		  Driver returns this if it can't recover without a hard
+		  slot reset.
+		- PCI_ERS_RESULT_DISCONNECT:
+		  Driver returns this if it doesn't want to recover at all.
+
+The next step taken will depend on the result codes returned by the
+drivers.
+
+If all drivers on the segment/slot return PCI_ERS_RESULT_CAN_RECOVER,
+then the platform should re-enable IOs on the slot (or do nothing in
+particular, if the platform doesn't isolate slots), and recovery
+proceeds to STEP 2 (MMIO Enable).
+
+If any driver requested a slot reset (by returning PCI_ERS_RESULT_NEED_RESET),
+then recovery proceeds to STEP 4 (Slot Reset).
+
+If the platform is unable to recover the slot, the next step
+is STEP 6 (Permanent Failure).
+
+>>> The current powerpc implementation assumes that a device driver will
+>>> *not* schedule or semaphore in this routine; the current powerpc
+>>> implementation uses one kernel thread to notify all devices;
+>>> thus, if one device sleeps/schedules, all devices are affected.
+>>> Doing better requires complex multi-threaded logic in the error
+>>> recovery implementation (e.g. waiting for all notification threads
+>>> to "join" before proceeding with recovery.)  This seems excessively
+>>> complex and not worth implementing.
+
+>>> The current powerpc implementation doesn't much care if the device
+>>> attempts I/O at this point, or not.  I/O's will fail, returning
+>>> a value of 0xff on read, and writes will be dropped. If the device
+>>> driver attempts more than 10K I/O's to a frozen adapter, it will
+>>> assume that the device driver has gone into an infinite loop, and
+>>> it will panic the kernel. There doesn't seem to be any other
+>>> way of stopping a device driver that insists on spinning on I/O.
+
+STEP 2: MMIO Enabled
+-------------------
+The platform re-enables MMIO to the device (but typically not the
+DMA), and then calls the mmio_enabled() callback on all affected
+device drivers.
+
+This is the "early recovery" call. IOs are allowed again, but DMA is
+not (hrm... to be discussed, I prefer not), with some restrictions. This
+is NOT a callback for the driver to start operations again, only to
+peek/poke at the device, extract diagnostic information, if any, and
+eventually do things like trigger a device local reset or some such,
+but not restart operations. This is callback is made if all drivers on
+a segment agree that they can try to recover and if no automatic link reset
+was performed by the HW. If the platform can't just re-enable IOs without
+a slot reset or a link reset, it wont call this callback, and instead
+will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset)
+
+>>> The following is proposed; no platform implements this yet:
+>>> Proposal: All I/O's should be done _synchronously_ from within
+>>> this callback, errors triggered by them will be returned via
+>>> the normal pci_check_whatever() API, no new error_detected()
+>>> callback will be issued due to an error happening here. However,
+>>> such an error might cause IOs to be re-blocked for the whole
+>>> segment, and thus invalidate the recovery that other devices
+>>> on the same segment might have done, forcing the whole segment
+>>> into one of the next states, that is, link reset or slot reset.
+
+The driver should return one of the following result codes:
+		- PCI_ERS_RESULT_RECOVERED
+		  Driver returns this if it thinks the device is fully
+		  functional and thinks it is ready to start
+		  normal driver operations again. There is no
+		  guarantee that the driver will actually be
+		  allowed to proceed, as another driver on the
+		  same segment might have failed and thus triggered a
+		  slot reset on platforms that support it.
+
+		- PCI_ERS_RESULT_NEED_RESET
+		  Driver returns this if it thinks the device is not
+		  recoverable in it's current state and it needs a slot
+		  reset to proceed.
+
+		- PCI_ERS_RESULT_DISCONNECT
+		  Same as above. Total failure, no recovery even after
+		  reset driver dead. (To be defined more precisely)
+
+The next step taken depends on the results returned by the drivers.
+If all drivers returned PCI_ERS_RESULT_RECOVERED, then the platform
+proceeds to either STEP3 (Link Reset) or to STEP 5 (Resume Operations).
+
+If any driver returned PCI_ERS_RESULT_NEED_RESET, then the platform
+proceeds to STEP 4 (Slot Reset)
+
+>>> The current powerpc implementation does not implement this callback.
+
+
+STEP 3: Link Reset
+------------------
+The platform resets the link, and then calls the link_reset() callback
+on all affected device drivers.  This is a PCI-Express specific state
+and is done whenever a non-fatal error has been detected that can be
+"solved" by resetting the link. This call informs the driver of the
+reset and the driver should check to see if the device appears to be
+in working condition.
+
+The driver is not supposed to restart normal driver I/O operations
+at this point.  It should limit itself to "probing" the device to
+check it's recoverability status. If all is right, then the platform
+will call resume() once all drivers have ack'd link_reset().
+
+	Result codes:
+		(identical to STEP 3 (MMIO Enabled)
+
+The platform then proceeds to either STEP 4 (Slot Reset) or STEP 5
+(Resume Operations).
+
+>>> The current powerpc implementation does not implement this callback.
+
+
+STEP 4: Slot Reset
+------------------
+The platform performs a soft or hard reset of the device, and then
+calls the slot_reset() callback.
+
+A soft reset consists of asserting the adapter #RST line and then
+restoring the PCI BAR's and PCI configuration header to a state
+that is equivalent to what it would be after a fresh system
+power-on followed by power-on BIOS/system firmware initialization.
+If the platform supports PCI hotplug, then the reset might be
+performed by toggling the slot electrical power off/on.
+
+It is important for the platform to restore the PCI config space
+to the "fresh poweron" state, rather than the "last state". After
+a slot reset, the device driver will almost always use its standard
+device initialization routines, and an unusual config space setup
+may result in hung devices, kernel panics, or silent data corruption.
+
+This call gives drivers the chance to re-initialize the hardware
+(re-download firmware, etc.).  At this point, the driver may assume
+that he card is in a fresh state and is fully functional. In
+particular, interrupt generation should work normally.
+
+Drivers should not yet restart normal I/O processing operations
+at this point.  If all device drivers report success on this
+callback, the platform will call resume() to complete the sequence,
+and let the driver restart normal I/O processing.
+
+A driver can still return a critical failure for this function if
+it can't get the device operational after reset.  If the platform
+previously tried a soft reset, it might now try a hard reset (power
+cycle) and then call slot_reset() again.  It the device still can't
+be recovered, there is nothing more that can be done;  the platform
+will typically report a "permanent failure" in such a case.  The
+device will be considered "dead" in this case.
+
+Drivers for multi-function cards will need to coordinate among
+themselves as to which driver instance will perform any "one-shot"
+or global device initialization. For example, the Symbios sym53cxx2
+driver performs device init only from PCI function 0:
+
++       if (PCI_FUNC(pdev->devfn) == 0)
++               sym_reset_scsi_bus(np, 0);
+
+	Result codes:
+		- PCI_ERS_RESULT_DISCONNECT
+		Same as above.
+
+Platform proceeds either to STEP 5 (Resume Operations) or STEP 6 (Permanent
+Failure).
+
+>>> The current powerpc implementation does not currently try a
+>>> power-cycle reset if the driver returned PCI_ERS_RESULT_DISCONNECT.
+>>> However, it probably should.
+
+
+STEP 5: Resume Operations
+-------------------------
+The platform will call the resume() callback on all affected device
+drivers if all drivers on the segment have returned
+PCI_ERS_RESULT_RECOVERED from one of the 3 previous callbacks.
+The goal of this callback is to tell the driver to restart activity,
+that everything is back and running. This callback does not return
+a result code.
+
+At this point, if a new error happens, the platform will restart
+a new error recovery sequence.
+
+STEP 6: Permanent Failure
+-------------------------
+A "permanent failure" has occurred, and the platform cannot recover
+the device.  The platform will call error_detected() with a
+pci_channel_state value of pci_channel_io_perm_failure.
+
+The device driver should, at this point, assume the worst. It should
+cancel all pending I/O, refuse all new I/O, returning -EIO to
+higher layers. The device driver should then clean up all of its
+memory and remove itself from kernel operations, much as it would
+during system shutdown.
+
+The platform will typically notify the system operator of the
+permanent failure in some way.  If the device is hotplug-capable,
+the operator will probably want to remove and replace the device.
+Note, however, not all failures are truly "permanent". Some are
+caused by over-heating, some by a poorly seated card. Many
+PCI error events are caused by software bugs, e.g. DMA's to
+wild addresses or bogus split transactions due to programming
+errors. See the discussion in powerpc/eeh-pci-error-recovery.txt
+for additional detail on real-life experience of the causes of
+software errors.
+
+
+Conclusion; General Remarks
+---------------------------
+The way those callbacks are called is platform policy. A platform with
+no slot reset capability may want to just "ignore" drivers that can't
+recover (disconnect them) and try to let other cards on the same segment
+recover. Keep in mind that in most real life cases, though, there will
+be only one driver per segment.
+
+Now, a note about interrupts. If you get an interrupt and your
+device is dead or has been isolated, there is a problem :)
+The current policy is to turn this into a platform policy.
+That is, the recovery API only requires that:
+
+ - There is no guarantee that interrupt delivery can proceed from any
+device on the segment starting from the error detection and until the
+resume callback is sent, at which point interrupts are expected to be
+fully operational.
+
+ - There is no guarantee that interrupt delivery is stopped, that is,
+a driver that gets an interrupt after detecting an error, or that detects
+an error within the interrupt handler such that it prevents proper
+ack'ing of the interrupt (and thus removal of the source) should just
+return IRQ_NOTHANDLED. It's up to the platform to deal with that
+condition, typically by masking the IRQ source during the duration of
+the error handling. It is expected that the platform "knows" which
+interrupts are routed to error-management capable slots and can deal
+with temporarily disabling that IRQ number during error processing (this
+isn't terribly complex). That means some IRQ latency for other devices
+sharing the interrupt, but there is simply no other way. High end
+platforms aren't supposed to share interrupts between many devices
+anyway :)
+
+>>> Implementation details for the powerpc platform are discussed in
+>>> the file Documentation/powerpc/eeh-pci-error-recovery.txt
+
+>>> As of this writing, there are six device drivers with patches
+>>> implementing error recovery. Not all of these patches are in
+>>> mainline yet. These may be used as "examples":
+>>>
+>>> drivers/scsi/ipr.c
+>>> drivers/scsi/sym53cxx_2
+>>> drivers/next/e100.c
+>>> drivers/net/e1000
+>>> drivers/net/ixgb
+>>> drivers/net/s2io.c
+
+The End
+-------
diff --git a/Documentation/PCI/pci.txt b/Documentation/PCI/pci.txt
new file mode 100644
index 000000000000..8d4dc6250c58
--- /dev/null
+++ b/Documentation/PCI/pci.txt
@@ -0,0 +1,646 @@
+
+			How To Write Linux PCI Drivers
+
+		by Martin Mares <mj@ucw.cz> on 07-Feb-2000
+	updated by Grant Grundler <grundler@parisc-linux.org> on 23-Dec-2006
+
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+The world of PCI is vast and full of (mostly unpleasant) surprises.
+Since each CPU architecture implements different chip-sets and PCI devices
+have different requirements (erm, "features"), the result is the PCI support
+in the Linux kernel is not as trivial as one would wish. This short paper
+tries to introduce all potential driver authors to Linux APIs for
+PCI device drivers.
+
+A more complete resource is the third edition of "Linux Device Drivers"
+by Jonathan Corbet, Alessandro Rubini, and Greg Kroah-Hartman.
+LDD3 is available for free (under Creative Commons License) from:
+
+	http://lwn.net/Kernel/LDD3/
+
+However, keep in mind that all documents are subject to "bit rot".
+Refer to the source code if things are not working as described here.
+
+Please send questions/comments/patches about Linux PCI API to the
+"Linux PCI" <linux-pci@atrey.karlin.mff.cuni.cz> mailing list.
+
+
+
+0. Structure of PCI drivers
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+PCI drivers "discover" PCI devices in a system via pci_register_driver().
+Actually, it's the other way around. When the PCI generic code discovers
+a new device, the driver with a matching "description" will be notified.
+Details on this below.
+
+pci_register_driver() leaves most of the probing for devices to
+the PCI layer and supports online insertion/removal of devices [thus
+supporting hot-pluggable PCI, CardBus, and Express-Card in a single driver].
+pci_register_driver() call requires passing in a table of function
+pointers and thus dictates the high level structure of a driver.
+
+Once the driver knows about a PCI device and takes ownership, the
+driver generally needs to perform the following initialization:
+
+	Enable the device
+	Request MMIO/IOP resources
+	Set the DMA mask size (for both coherent and streaming DMA)
+	Allocate and initialize shared control data (pci_allocate_coherent())
+	Access device configuration space (if needed)
+	Register IRQ handler (request_irq())
+	Initialize non-PCI (i.e. LAN/SCSI/etc parts of the chip)
+	Enable DMA/processing engines
+
+When done using the device, and perhaps the module needs to be unloaded,
+the driver needs to take the follow steps:
+	Disable the device from generating IRQs
+	Release the IRQ (free_irq())
+	Stop all DMA activity
+	Release DMA buffers (both streaming and coherent)
+	Unregister from other subsystems (e.g. scsi or netdev)
+	Release MMIO/IOP resources
+	Disable the device
+
+Most of these topics are covered in the following sections.
+For the rest look at LDD3 or <linux/pci.h> .
+
+If the PCI subsystem is not configured (CONFIG_PCI is not set), most of
+the PCI functions described below are defined as inline functions either
+completely empty or just returning an appropriate error codes to avoid
+lots of ifdefs in the drivers.
+
+
+
+1. pci_register_driver() call
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PCI device drivers call pci_register_driver() during their
+initialization with a pointer to a structure describing the driver
+(struct pci_driver):
+
+	field name	Description
+	----------	------------------------------------------------------
+	id_table	Pointer to table of device ID's the driver is
+			interested in.  Most drivers should export this
+			table using MODULE_DEVICE_TABLE(pci,...).
+
+	probe		This probing function gets called (during execution
+			of pci_register_driver() for already existing
+			devices or later if a new device gets inserted) for
+			all PCI devices which match the ID table and are not
+			"owned" by the other drivers yet. This function gets
+			passed a "struct pci_dev *" for each device whose
+			entry in the ID table matches the device. The probe
+			function returns zero when the driver chooses to
+			take "ownership" of the device or an error code
+			(negative number) otherwise.
+			The probe function always gets called from process
+			context, so it can sleep.
+
+	remove		The remove() function gets called whenever a device
+			being handled by this driver is removed (either during
+			deregistration of the driver or when it's manually
+			pulled out of a hot-pluggable slot).
+			The remove function always gets called from process
+			context, so it can sleep.
+
+	suspend		Put device into low power state.
+	suspend_late	Put device into low power state.
+
+	resume_early	Wake device from low power state.
+	resume		Wake device from low power state.
+
+		(Please see Documentation/power/pci.txt for descriptions
+		of PCI Power Management and the related functions.)
+
+	shutdown	Hook into reboot_notifier_list (kernel/sys.c).
+			Intended to stop any idling DMA operations.
+			Useful for enabling wake-on-lan (NIC) or changing
+			the power state of a device before reboot.
+			e.g. drivers/net/e100.c.
+
+	err_handler	See Documentation/PCI/pci-error-recovery.txt
+
+
+The ID table is an array of struct pci_device_id entries ending with an
+all-zero entry; use of the macro DEFINE_PCI_DEVICE_TABLE is the preferred
+method of declaring the table.  Each entry consists of:
+
+	vendor,device	Vendor and device ID to match (or PCI_ANY_ID)
+
+	subvendor,	Subsystem vendor and device ID to match (or PCI_ANY_ID)
+	subdevice,
+
+	class		Device class, subclass, and "interface" to match.
+			See Appendix D of the PCI Local Bus Spec or
+			include/linux/pci_ids.h for a full list of classes.
+			Most drivers do not need to specify class/class_mask
+			as vendor/device is normally sufficient.
+
+	class_mask	limit which sub-fields of the class field are compared.
+			See drivers/scsi/sym53c8xx_2/ for example of usage.
+
+	driver_data	Data private to the driver.
+			Most drivers don't need to use driver_data field.
+			Best practice is to use driver_data as an index
+			into a static list of equivalent device types,
+			instead of using it as a pointer.
+
+
+Most drivers only need PCI_DEVICE() or PCI_DEVICE_CLASS() to set up
+a pci_device_id table.
+
+New PCI IDs may be added to a device driver pci_ids table at runtime
+as shown below:
+
+echo "vendor device subvendor subdevice class class_mask driver_data" > \
+/sys/bus/pci/drivers/{driver}/new_id
+
+All fields are passed in as hexadecimal values (no leading 0x).
+The vendor and device fields are mandatory, the others are optional. Users
+need pass only as many optional fields as necessary:
+	o subvendor and subdevice fields default to PCI_ANY_ID (FFFFFFFF)
+	o class and classmask fields default to 0
+	o driver_data defaults to 0UL.
+
+Once added, the driver probe routine will be invoked for any unclaimed
+PCI devices listed in its (newly updated) pci_ids list.
+
+When the driver exits, it just calls pci_unregister_driver() and the PCI layer
+automatically calls the remove hook for all devices handled by the driver.
+
+
+1.1 "Attributes" for driver functions/data
+
+Please mark the initialization and cleanup functions where appropriate
+(the corresponding macros are defined in <linux/init.h>):
+
+	__init		Initialization code. Thrown away after the driver
+			initializes.
+	__exit		Exit code. Ignored for non-modular drivers.
+
+
+	__devinit	Device initialization code.
+			Identical to __init if the kernel is not compiled
+			with CONFIG_HOTPLUG, normal function otherwise.
+	__devexit	The same for __exit.
+
+Tips on when/where to use the above attributes:
+	o The module_init()/module_exit() functions (and all
+	  initialization functions called _only_ from these)
+	  should be marked __init/__exit.
+
+	o Do not mark the struct pci_driver.
+
+	o The ID table array should be marked __devinitconst; this is done
+	  automatically if the table is declared with DEFINE_PCI_DEVICE_TABLE().
+
+	o The probe() and remove() functions should be marked __devinit
+	  and __devexit respectively.  All initialization functions
+	  exclusively called by the probe() routine, can be marked __devinit.
+	  Ditto for remove() and __devexit.
+
+	o If mydriver_remove() is marked with __devexit(), then all address
+	  references to mydriver_remove must use __devexit_p(mydriver_remove)
+	  (in the struct pci_driver declaration for example).
+	  __devexit_p() will generate the function name _or_ NULL if the
+	  function will be discarded.  For an example, see drivers/net/tg3.c.
+
+	o Do NOT mark a function if you are not sure which mark to use.
+	  Better to not mark the function than mark the function wrong.
+
+
+
+2. How to find PCI devices manually
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+PCI drivers should have a r