Merge tag 'iio-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 4.5 cycle

Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.

New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
 Also associated minor changes.
   - Set the device buffer watermark based on the minimum watermark for all
     attached buffers rather than just the 'primary' one.
   - iio_buffer_init - only set the watermark default if one hasn't already
     been provided.  This allows simple support for devices with a fixed
     watermark.
   - read only attribute for watermark on fixed watermark devices.
   - add explicit buffer enable/disable callbacks to allow the buffer to
     do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.

New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc

New driver features
* mma8452
  - support either of the available interrupt pins to cope with the case
    where board layout has lead to a particular one being connected.

Staging graduation
* Dummy driver
  - this driver acts as both an example and a test device for those with
    out hardware to develop userspace code against.

Cleanups and minor bits and bobs.
* treewide
  - Sort out the ordering of iio_device_register/unregister vs runtime
    pm function calls so that it's all nice and consistent and not race
    prone.
  - Check sscanf return values.  None of the cases will actually happen as
    the strings are supplied internally, but best to be consistent on this.
* ad7780
  - switch over to the gpio descriptor interface and remove the now unused
    platform data which gets rid of a header entirely.
* ad7793
  - drop a pointless else statement.
* at91_adc
  - Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
  - get rid of some commented out lines that snuck in during the move of
    the driver.
* lm3533-als
  - Print an error message on provision of an invalid resistance.
* mcp320x
  - Add compatible strings with vendor prefix and deprecate those with
    no vendor prefix.
* mxs-lradc
  - Use BIT macro in various places rather than shifted ones.
* pa12203001
  - Power off the chip if the registration fails.
* pulsedlight-lidar-lite
  - add runtime PM support.
* xilinx XADC
  - constify an iio_buffer_setup_ops structure.

64 files changed, 3625 insertions, 238 deletions

diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
index e3c37467d7da..3c10e8581144 100644
--- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
+++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
@@ -7,13 +7,18 @@ Required properties:
     * "fsl,mma8453"
     * "fsl,mma8652"
     * "fsl,mma8653"
+
   - reg: the I2C address of the chip
 
 Optional properties:
 
   - interrupt-parent: should be the phandle for the interrupt controller
+
   - interrupts: interrupt mapping for GPIO IRQ
 
+  - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's
+		     interrupt line in use.
+
 Example:
 
 	mma8453fc@1d {
@@ -21,4 +26,5 @@ Example:
 		reg = <0x1d>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <5 0>;
+		interrupt-names = "INT2";
 	};
diff --git a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt
index 2a1f3af30155..bcd3ac8e6e0c 100644
--- a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt
+++ b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt
@@ -10,16 +10,28 @@ must be specified.
 Required properties:
 	- compatible:  	Must be one of the following, depending on the
 			model:
-				"mcp3001"
-				"mcp3002"
-				"mcp3004"
-				"mcp3008"
-				"mcp3201"
-				"mcp3202"
-				"mcp3204"
-				"mcp3208"
-				"mcp3301"
+				"mcp3001" (DEPRECATED)
+				"mcp3002" (DEPRECATED)
+				"mcp3004" (DEPRECATED)
+				"mcp3008" (DEPRECATED)
+				"mcp3201" (DEPRECATED)
+				"mcp3202" (DEPRECATED)
+				"mcp3204" (DEPRECATED)
+				"mcp3208" (DEPRECATED)
+				"mcp3301" (DEPRECATED)
 
+				"microchip,mcp3001"
+				"microchip,mcp3002"
+				"microchip,mcp3004"
+				"microchip,mcp3008"
+				"microchip,mcp3201"
+				"microchip,mcp3202"
+				"microchip,mcp3204"
+				"microchip,mcp3208"
+				"microchip,mcp3301"
+
+			NOTE: The use of the compatibles with no vendor prefix
+			is deprecated and only listed because old DT use them.
 
 Examples:
 spi_controller {
diff --git a/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt b/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt
new file mode 100644
index 000000000000..4bb9a86065d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt
@@ -0,0 +1,48 @@
+* Palmas general purpose ADC IP block devicetree bindings
+
+Channels list:
+	0 battery type
+	1 battery temp NTC (optional current source)
+	2 GP
+	3 temp (with ext. diode, optional current source)
+	4 GP
+	5 GP
+	6 VBAT_SENSE
+	7 VCC_SENSE
+	8 Backup Battery voltage
+	9 external charger (VCHG)
+	10 VBUS
+	11 DC-DC current probe (how does this work?)
+	12 internal die temp
+	13 internal die temp
+	14 USB ID pin voltage
+	15 test network
+
+Required properties:
+- compatible : Must be "ti,palmas-gpadc".
+- #io-channel-cells: Should be set to <1>.
+
+Optional sub-nodes:
+ti,channel0-current-microamp: Channel 0 current in uA.
+	Values are rounded to derive 0uA, 5uA, 15uA, 20uA.
+ti,channel3-current-microamp: Channel 3 current in uA.
+	Values are rounded to derive 0uA, 10uA, 400uA, 800uA.
+ti,enable-extended-delay: Enable extended delay.
+
+Example:
+
+pmic {
+	compatible = "ti,twl6035-pmic", "ti,palmas-pmic";
+	...
+	gpadc {
+		compatible = "ti,palmas-gpadc";
+		interrupts = <18 0
+			      16 0
+			      17 0>;
+		#io-channel-cells = <1>;
+		ti,channel0-current-microamp = <5>;
+		ti,channel3-current-microamp = <10>;
+		};
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads8688.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads8688.txt
new file mode 100644
index 000000000000..a02337d7efa4
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/ti-ads8688.txt
@@ -0,0 +1,20 @@
+* Texas Instruments' ADS8684 and ADS8688 ADC chip
+
+Required properties:
+ - compatible: Should be "ti,ads8684" or "ti,ads8688"
+ - reg: spi chip select number for the device
+
+Recommended properties:
+ - spi-max-frequency: Definition as per
+		Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Optional properties:
+ - vref-supply: The regulator supply for ADC reference voltage
+
+Example:
+adc@0 {
+	compatible = "ti,ads8688";
+	reg = <0>;
+	vref-supply = <&vdd_supply>;
+	spi-max-frequency = <1000000>;
+};
diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt
index d3ccdb190c53..d4b87cc1e446 100644
--- a/Documentation/devicetree/bindings/iio/st-sensors.txt
+++ b/Documentation/devicetree/bindings/iio/st-sensors.txt
@@ -36,6 +36,7 @@ Accelerometers:
 - st,lsm303dlm-accel
 - st,lsm330-accel
 - st,lsm303agr-accel
+- st,lis2dh12-accel
 
 Gyroscopes:
 - st,l3g4200d-gyro
diff --git a/drivers/iio/Kconfig b/drivers/iio/Kconfig
index 66792e707d74..6b8c77c97d40 100644
--- a/drivers/iio/Kconfig
+++ b/drivers/iio/Kconfig
@@ -50,6 +50,7 @@ source "drivers/iio/amplifiers/Kconfig"
 source "drivers/iio/chemical/Kconfig"
 source "drivers/iio/common/Kconfig"
 source "drivers/iio/dac/Kconfig"
+source "drivers/iio/dummy/Kconfig"
 source "drivers/iio/frequency/Kconfig"
 source "drivers/iio/gyro/Kconfig"
 source "drivers/iio/humidity/Kconfig"
diff --git a/drivers/iio/Makefile b/drivers/iio/Makefile
index aeca7269fe44..6769f2f43e86 100644
--- a/drivers/iio/Makefile
+++ b/drivers/iio/Makefile
@@ -16,6 +16,7 @@ obj-y += buffer/
 obj-y += chemical/
 obj-y += common/
 obj-y += dac/
+obj-y += dummy/
 obj-y += gyro/
 obj-y += frequency/
 obj-y += humidity/
diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig
index 969428dd6329..edc29b173f6c 100644
--- a/drivers/iio/accel/Kconfig
+++ b/drivers/iio/accel/Kconfig
@@ -64,7 +64,7 @@ config IIO_ST_ACCEL_3AXIS
 	help
 	  Say yes here to build support for STMicroelectronics accelerometers:
 	  LSM303DLH, LSM303DLHC, LIS3DH, LSM330D, LSM330DL, LSM330DLC,
-	  LIS331DLH, LSM303DL, LSM303DLM, LSM330.
+	  LIS331DLH, LSM303DL, LSM303DLM, LSM330, LIS2DH12.
 
 	  This driver can also be built as a module. If so, these modules
 	  will be created:
@@ -107,6 +107,35 @@ config KXCJK1013
 	  To compile this driver as a module, choose M here: the module will
 	  be called kxcjk-1013.
 
+config MMA7455
+	tristate
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+
+config MMA7455_I2C
+	tristate "Freescale MMA7455L/MMA7456L Accelerometer I2C Driver"
+	depends on I2C
+	select MMA7455
+	select REGMAP_I2C
+	help
+	  Say yes here to build support for the Freescale MMA7455L and
+	  MMA7456L 3-axis accelerometer.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called mma7455_i2c.
+
+config MMA7455_SPI
+	tristate "Freescale MMA7455L/MMA7456L Accelerometer SPI Driver"
+	depends on SPI_MASTER
+	select MMA7455
+	select REGMAP_SPI
+	help
+	  Say yes here to build support for the Freescale MMA7455L and
+	  MMA7456L 3-axis accelerometer.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called mma7455_spi.
+
 config MMA8452
 	tristate "Freescale MMA8452Q and similar Accelerometers Driver"
 	depends on I2C
@@ -158,6 +187,17 @@ config MXC4005
 	  To compile this driver as a module, choose M. The module will be
 	  called mxc4005.
 
+config MXC6255
+	tristate "Memsic MXC6255 Orientation Sensing Accelerometer Driver"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Say yes here to build support for the Memsic MXC6255 Orientation
+	  Sensing Accelerometer Driver.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called mxc6255.
+
 config STK8312
 	tristate "Sensortek STK8312 3-Axis Accelerometer Driver"
 	depends on I2C
diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile
index 7925f166e6e9..71b6794de885 100644
--- a/drivers/iio/accel/Makefile
+++ b/drivers/iio/accel/Makefile
@@ -10,6 +10,11 @@ obj-$(CONFIG_BMC150_ACCEL_SPI) += bmc150-accel-spi.o
 obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o
 obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o
 obj-$(CONFIG_KXSD9)	+= kxsd9.o
+
+obj-$(CONFIG_MMA7455)		+= mma7455_core.o
+obj-$(CONFIG_MMA7455_I2C)	+= mma7455_i2c.o
+obj-$(CONFIG_MMA7455_SPI)	+= mma7455_spi.o
+
 obj-$(CONFIG_MMA8452)	+= mma8452.o
 
 obj-$(CONFIG_MMA9551_CORE)	+= mma9551_core.o
@@ -17,6 +22,7 @@ obj-$(CONFIG_MMA9551)		+= mma9551.o
 obj-$(CONFIG_MMA9553)		+= mma9553.o
 
 obj-$(CONFIG_MXC4005)		+= mxc4005.o
+obj-$(CONFIG_MXC6255)		+= mxc6255.o
 
 obj-$(CONFIG_STK8312)		+= stk8312.o
 obj-$(CONFIG_STK8BA50)		+= stk8ba50.o
diff --git a/drivers/iio/accel/bmc150-accel-core.c b/drivers/iio/accel/bmc150-accel-core.c
index 2d33f1e821db..c73331f7782b 100644
--- a/drivers/iio/accel/bmc150-accel-core.c
+++ b/drivers/iio/accel/bmc150-accel-core.c
@@ -1623,24 +1623,22 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 		}
 	}
 
-	ret = iio_device_register(indio_dev);
-	if (ret < 0) {
-		dev_err(dev, "Unable to register iio device\n");
-		goto err_trigger_unregister;
-	}
-
 	ret = pm_runtime_set_active(dev);
 	if (ret)
-		goto err_iio_unregister;
+		goto err_trigger_unregister;
 
 	pm_runtime_enable(dev);
 	pm_runtime_set_autosuspend_delay(dev, BMC150_AUTO_SUSPEND_DELAY_MS);
 	pm_runtime_use_autosuspend(dev);
 
+	ret = iio_device_register(indio_dev);
+	if (ret < 0) {
+		dev_err(dev, "Unable to register iio device\n");
+		goto err_trigger_unregister;
+	}
+
 	return 0;
 
-err_iio_unregister:
-	iio_device_unregister(indio_dev);
 err_trigger_unregister:
 	bmc150_accel_unregister_triggers(data, BMC150_ACCEL_TRIGGERS - 1);
 err_buffer_cleanup:
@@ -1655,12 +1653,12 @@ int bmc150_accel_core_remove(struct device *dev)
 	struct iio_dev *indio_dev = dev_get_drvdata(dev);
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
 
+	iio_device_unregister(indio_dev);
+
 	pm_runtime_disable(data->dev);
 	pm_runtime_set_suspended(data->dev);
 	pm_runtime_put_noidle(data->dev);
 
-	iio_device_unregister(indio_dev);
-
 	bmc150_accel_unregister_triggers(data, BMC150_ACCEL_TRIGGERS - 1);
 
 	iio_triggered_buffer_cleanup(indio_dev);
diff --git a/drivers/iio/accel/kxcjk-1013.c b/drivers/iio/accel/kxcjk-1013.c
index 18c1b06684c1..edec1d099e91 100644
--- a/drivers/iio/accel/kxcjk-1013.c
+++ b/drivers/iio/accel/kxcjk-1013.c
@@ -1264,25 +1264,23 @@ static int kxcjk1013_probe(struct i2c_client *client,
 		goto err_trigger_unregister;
 	}
 
-	ret = iio_device_register(indio_dev);
-	if (ret < 0) {
-		dev_err(&client->dev, "unable to register iio device\n");
-		goto err_buffer_cleanup;
-	}
-
 	ret = pm_runtime_set_active(&client->dev);
 	if (ret)
-		goto err_iio_unregister;
+		goto err_buffer_cleanup;
 
 	pm_runtime_enable(&client->dev);
 	pm_runtime_set_autosuspend_delay(&client->dev,
 					 KXCJK1013_SLEEP_DELAY_MS);
 	pm_runtime_use_autosuspend(&client->dev);
 
+	ret = iio_device_register(indio_dev);
+	if (ret < 0) {
+		dev_err(&client->dev, "unable to register iio device\n");
+		goto err_buffer_cleanup;
+	}
+
 	return 0;
 
-err_iio_unregister:
-	iio_device_unregister(indio_dev);
 err_buffer_cleanup:
 	if (data->dready_trig)
 		iio_triggered_buffer_cleanup(indio_dev);
@@ -1302,12 +1300,12 @@ static int kxcjk1013_remove(struct i2c_client *client)
 	struct iio_dev *indio_dev = i2c_get_clientdata(client);
 	struct kxcjk1013_data *data = iio_priv(indio_dev);
 
+	iio_device_unregister(indio_dev);
+
 	pm_runtime_disable(&client->dev);
 	pm_runtime_set_suspended(&client->dev);
 	pm_runtime_put_noidle(&client->dev);
 
-	iio_device_unregister(indio_dev);
-
 	if (data->dready_trig) {
 		iio_triggered_buffer_cleanup(indio_dev);
 		iio_trigger_unregister(data->dready_trig);
diff --git a/drivers/iio/accel/mma7455.h b/drivers/iio/accel/mma7455.h
new file mode 100644
index 000000000000..2b1152c53d4f
--- /dev/null
+++ b/drivers/iio/accel/mma7455.h
@@ -0,0 +1,19 @@
+/*
+ * IIO accel driver for Freescale MMA7455L 3-axis 10-bit accelerometer
+ * Copyright 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MMA7455_H
+#define __MMA7455_H
+
+extern const struct regmap_config mma7455_core_regmap;
+
+int mma7455_core_probe(struct device *dev, struct regmap *regmap,
+		       const char *name);
+int mma7455_core_remove(struct device *dev);
+
+#endif
diff --git a/drivers/iio/accel/mma7455_core.c b/drivers/iio/accel/mma7455_core.c
new file mode 100644
index 000000000000..c633cc2c0789
--- /dev/null
+++ b/drivers/iio/accel/mma7455_core.c
@@ -0,0 +1,311 @@
+/*
+ * IIO accel core driver for Freescale MMA7455L 3-axis 10-bit accelerometer
+ * Copyright 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * UNSUPPORTED hardware features:
+ *  - 8-bit mode with different scales
+ *  - INT1/INT2 interrupts
+ *  - Offset calibration
+ *  - Events
+ */
+
+#include <linux/delay.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+
+#include "mma7455.h"
+
+#define MMA7455_REG_XOUTL		0x00
+#define MMA7455_REG_XOUTH		0x01
+#define MMA7455_REG_YOUTL		0x02
+#define MMA7455_REG_YOUTH		0x03
+#define MMA7455_REG_ZOUTL		0x04
+#define MMA7455_REG_ZOUTH		0x05
+#define MMA7455_REG_STATUS		0x09
+#define  MMA7455_STATUS_DRDY		BIT(0)
+#define MMA7455_REG_WHOAMI		0x0f
+#define  MMA7455_WHOAMI_ID		0x55
+#define MMA7455_REG_MCTL		0x16
+#define  MMA7455_MCTL_MODE_STANDBY	0x00
+#define  MMA7455_MCTL_MODE_MEASURE	0x01
+#define MMA7455_REG_CTL1		0x18
+#define  MMA7455_CTL1_DFBW_MASK		BIT(7)
+#define  MMA7455_CTL1_DFBW_125HZ	BIT(7)
+#define  MMA7455_CTL1_DFBW_62_5HZ	0
+#define MMA7455_REG_TW			0x1e
+
+/*
+ * When MMA7455 is used in 10-bit it has a fullscale of -8g
+ * corresponding to raw value -512. The userspace interface
+ * uses m/s^2 and we declare micro units.
+ * So scale factor is given by:
+ *       g * 8 * 1e6 / 512 = 153228.90625, with g = 9.80665
+ */
+#define MMA7455_10BIT_SCALE	153229
+
+struct mma7455_data {
+	struct regmap *regmap;
+	struct device *dev;
+};
+
+static int mma7455_drdy(struct mma7455_data *mma7455)
+{
+	unsigned int reg;
+	int tries = 3;
+	int ret;
+
+	while (tries-- > 0) {
+		ret = regmap_read(mma7455->regmap, MMA7455_REG_STATUS, &reg);
+		if (ret)
+			return ret;
+
+		if (reg & MMA7455_STATUS_DRDY)
+			return 0;
+
+		msleep(20);
+	}
+
+	dev_warn(mma7455->dev, "data not ready\n");
+
+	return -EIO;
+}
+
+static irqreturn_t mma7455_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct mma7455_data *mma7455 = iio_priv(indio_dev);
+	u8 buf[16]; /* 3 x 16-bit channels + padding + ts */
+	int ret;
+
+	ret = mma7455_drdy(mma7455);
+	if (ret)
+		goto done;
+
+	ret = regmap_bulk_read(mma7455->regmap, MMA7455_REG_XOUTL, buf,
+			       sizeof(__le16) * 3);
+	if (ret)
+		goto done;
+
+	iio_push_to_buffers_with_timestamp(indio_dev, buf, iio_get_time_ns());
+
+done:
+	iio_trigger_notify_done(indio_dev->trig);
+
+	return IRQ_HANDLED;
+}
+
+static int mma7455_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int *val, int *val2, long mask)
+{
+	struct mma7455_data *mma7455 = iio_priv(indio_dev);
+	unsigned int reg;
+	__le16 data;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		if (iio_buffer_enabled(indio_dev))
+			return -EBUSY;
+
+		ret = mma7455_drdy(mma7455);
+		if (ret)
+			return ret;
+
+		ret = regmap_bulk_read(mma7455->regmap, chan->address, &data,
+				       sizeof(data));
+		if (ret)
+			return ret;
+