Revert "remove the strip driver"

This reverts commit 94d9842403f770239a656586442454b7a8f2df29.

Alan says it's not appropriate to remove this driver,
Adrian Bunk also agrees with this revert.

Signed-off-by: David S. Miller <davem@davemloft.net>

4 files changed, 2833 insertions, 0 deletions

diff --git a/MAINTAINERS b/MAINTAINERS
index f92707fee59e..ec0c9c914f17 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3908,6 +3908,10 @@ P:	Ion Badulescu
 M:	ionut@cs.columbia.edu
 S:	Maintained
 
+STARMODE RADIO IP (STRIP) PROTOCOL DRIVER
+W:	http://mosquitonet.Stanford.EDU/strip.html
+S:	Unsupported ?
+
 STRADIS MPEG-2 DECODER DRIVER
 P:	Nathan Laredo
 M:	laredo@gnu.org
diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig
index d5b006f5b86f..91fc2c765d90 100644
--- a/drivers/net/wireless/Kconfig
+++ b/drivers/net/wireless/Kconfig
@@ -14,6 +14,30 @@ config WLAN_PRE80211
 	  This option does not affect the kernel build, it only
 	  lets you choose drivers.
 
+config STRIP
+	tristate "STRIP (Metricom starmode radio IP)"
+	depends on INET && WLAN_PRE80211
+	select WIRELESS_EXT
+	---help---
+	  Say Y if you have a Metricom radio and intend to use Starmode Radio
+	  IP. STRIP is a radio protocol developed for the MosquitoNet project
+	  (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
+	  traffic using Metricom radios.  Metricom radios are small, battery
+	  powered, 100kbit/sec packet radio transceivers, about the size and
+	  weight of a cellular telephone. (You may also have heard them called
+	  "Metricom modems" but we avoid the term "modem" because it misleads
+	  many people into thinking that you can plug a Metricom modem into a
+	  phone line and use it as a modem.)
+
+	  You can use STRIP on any Linux machine with a serial port, although
+	  it is obviously most useful for people with laptop computers. If you
+	  think you might get a Metricom radio in the future, there is no harm
+	  in saying Y to STRIP now, except that it makes the kernel a bit
+	  bigger.
+
+	  To compile this as a module, choose M here: the module will be
+	  called strip.
+
 config ARLAN
 	tristate "Aironet Arlan 655 & IC2200 DS support"
 	depends on ISA && !64BIT && WLAN_PRE80211
diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile
index 2668934abbff..54a4f6f1db67 100644
--- a/drivers/net/wireless/Makefile
+++ b/drivers/net/wireless/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_IPW2100) += ipw2100.o
 
 obj-$(CONFIG_IPW2200) += ipw2200.o
 
+obj-$(CONFIG_STRIP) += strip.o
 obj-$(CONFIG_ARLAN) += arlan.o 
 
 arlan-objs := arlan-main.o arlan-proc.o
diff --git a/drivers/net/wireless/strip.c b/drivers/net/wireless/strip.c
new file mode 100644
index 000000000000..883af891ebfb
--- /dev/null
+++ b/drivers/net/wireless/strip.c
@@ -0,0 +1,2804 @@
+/*
+ * Copyright 1996 The Board of Trustees of The Leland Stanford
+ * Junior University. All Rights Reserved.
+ *
+ * Permission to use, copy, modify, and distribute this
+ * software and its documentation for any purpose and without
+ * fee is hereby granted, provided that the above copyright
+ * notice appear in all copies.  Stanford University
+ * makes no representations about the suitability of this
+ * software for any purpose.  It is provided "as is" without
+ * express or implied warranty.
+ *
+ * strip.c	This module implements Starmode Radio IP (STRIP)
+ *		for kernel-based devices like TTY.  It interfaces between a
+ *		raw TTY, and the kernel's INET protocol layers (via DDI).
+ *
+ * Version:	@(#)strip.c	1.3	July 1997
+ *
+ * Author:	Stuart Cheshire <cheshire@cs.stanford.edu>
+ *
+ * Fixes:	v0.9 12th Feb 1996 (SC)
+ *		New byte stuffing (2+6 run-length encoding)
+ *		New watchdog timer task
+ *		New Protocol key (SIP0)
+ *		
+ *		v0.9.1 3rd March 1996 (SC)
+ *		Changed to dynamic device allocation -- no more compile
+ *		time (or boot time) limit on the number of STRIP devices.
+ *		
+ *		v0.9.2 13th March 1996 (SC)
+ *		Uses arp cache lookups (but doesn't send arp packets yet)
+ *		
+ *		v0.9.3 17th April 1996 (SC)
+ *		Fixed bug where STR_ERROR flag was getting set unneccessarily
+ *		(causing otherwise good packets to be unneccessarily dropped)
+ *		
+ *		v0.9.4 27th April 1996 (SC)
+ *		First attempt at using "&COMMAND" Starmode AT commands
+ *		
+ *		v0.9.5 29th May 1996 (SC)
+ *		First attempt at sending (unicast) ARP packets
+ *		
+ *		v0.9.6 5th June 1996 (Elliot)
+ *		Put "message level" tags in every "printk" statement
+ *		
+ *		v0.9.7 13th June 1996 (laik)
+ *		Added support for the /proc fs
+ *
+ *              v0.9.8 July 1996 (Mema)
+ *              Added packet logging
+ *
+ *              v1.0 November 1996 (SC)
+ *              Fixed (severe) memory leaks in the /proc fs code
+ *              Fixed race conditions in the logging code
+ *
+ *              v1.1 January 1997 (SC)
+ *              Deleted packet logging (use tcpdump instead)
+ *              Added support for Metricom Firmware v204 features
+ *              (like message checksums)
+ *
+ *              v1.2 January 1997 (SC)
+ *              Put portables list back in
+ *
+ *              v1.3 July 1997 (SC)
+ *              Made STRIP driver set the radio's baud rate automatically.
+ *              It is no longer necessarily to manually set the radio's
+ *              rate permanently to 115200 -- the driver handles setting
+ *              the rate automatically.
+ */
+
+#ifdef MODULE
+static const char StripVersion[] = "1.3A-STUART.CHESHIRE-MODULAR";
+#else
+static const char StripVersion[] = "1.3A-STUART.CHESHIRE";
+#endif
+
+#define TICKLE_TIMERS 0
+#define EXT_COUNTERS 1
+
+
+/************************************************************************/
+/* Header files								*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/bitops.h>
+#include <asm/system.h>
+#include <asm/uaccess.h>
+
+# include <linux/ctype.h>
+#include <linux/string.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/in.h>
+#include <linux/tty.h>
+#include <linux/errno.h>
+#include <linux/netdevice.h>
+#include <linux/inetdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/if_arp.h>
+#include <linux/if_strip.h>
+#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
+#include <linux/serial.h>
+#include <linux/serialP.h>
+#include <linux/rcupdate.h>
+#include <net/arp.h>
+#include <net/net_namespace.h>
+
+#include <linux/ip.h>
+#include <linux/tcp.h>
+#include <linux/time.h>
+#include <linux/jiffies.h>
+
+/************************************************************************/
+/* Useful structures and definitions					*/
+
+/*
+ * A MetricomKey identifies the protocol being carried inside a Metricom
+ * Starmode packet.
+ */
+
+typedef union {
+	__u8 c[4];
+	__u32 l;
+} MetricomKey;
+
+/*
+ * An IP address can be viewed as four bytes in memory (which is what it is) or as
+ * a single 32-bit long (which is convenient for assignment, equality testing etc.)
+ */
+
+typedef union {
+	__u8 b[4];
+	__u32 l;
+} IPaddr;
+
+/*
+ * A MetricomAddressString is used to hold a printable representation of
+ * a Metricom address.
+ */
+
+typedef struct {
+	__u8 c[24];
+} MetricomAddressString;
+
+/* Encapsulation can expand packet of size x to 65/64x + 1
+ * Sent packet looks like "<CR>*<address>*<key><encaps payload><CR>"
+ *                           1 1   1-18  1  4         ?         1
+ * eg.                     <CR>*0000-1234*SIP0<encaps payload><CR>
+ * We allow 31 bytes for the stars, the key, the address and the <CR>s
+ */
+#define STRIP_ENCAP_SIZE(X) (32 + (X)*65L/64L)
+
+/*
+ * A STRIP_Header is never really sent over the radio, but making a dummy
+ * header for internal use within the kernel that looks like an Ethernet
+ * header makes certain other software happier. For example, tcpdump
+ * already understands Ethernet headers.
+ */
+
+typedef struct {
+	MetricomAddress dst_addr;	/* Destination address, e.g. "0000-1234"   */
+	MetricomAddress src_addr;	/* Source address, e.g. "0000-5678"        */
+	unsigned short protocol;	/* The protocol type, using Ethernet codes */
+} STRIP_Header;
+
+typedef struct {
+	char c[60];
+} MetricomNode;
+
+#define NODE_TABLE_SIZE 32
+typedef struct {
+	struct timeval timestamp;
+	int num_nodes;
+	MetricomNode node[NODE_TABLE_SIZE];
+} MetricomNodeTable;
+
+enum { FALSE = 0, TRUE = 1 };
+
+/*
+ * Holds the radio's firmware version.
+ */
+typedef struct {
+	char c[50];
+} FirmwareVersion;
+
+/*
+ * Holds the radio's serial number.
+ */
+typedef struct {
+	char c[18];
+} SerialNumber;
+
+/*
+ * Holds the radio's battery voltage.
+ */
+typedef struct {
+	char c[11];
+} BatteryVoltage;
+
+typedef struct {
+	char c[8];
+} char8;
+
+enum {
+	NoStructure = 0,	/* Really old firmware */
+	StructuredMessages = 1,	/* Parsable AT response msgs */
+	ChecksummedMessages = 2	/* Parsable AT response msgs with checksums */
+};
+
+struct strip {
+	int magic;
+	/*
+	 * These are pointers to the malloc()ed frame buffers.
+	 */
+
+	unsigned char *rx_buff;	/* buffer for received IP packet */
+	unsigned char *sx_buff;	/* buffer for received serial data */
+	int sx_count;		/* received serial data counter */
+	int sx_size;		/* Serial buffer size           */
+	unsigned char *tx_buff;	/* transmitter buffer           */
+	unsigned char *tx_head;	/* pointer to next byte to XMIT */
+	int tx_left;		/* bytes left in XMIT queue     */
+	int tx_size;		/* Serial buffer size           */
+
+	/*
+	 * STRIP interface statistics.
+	 */
+
+	unsigned long rx_packets;	/* inbound frames counter       */
+	unsigned long tx_packets;	/* outbound frames counter      */
+	unsigned long rx_errors;	/* Parity, etc. errors          */
+	unsigned long tx_errors;	/* Planned stuff                */
+	unsigned long rx_dropped;	/* No memory for skb            */
+	unsigned long tx_dropped;	/* When MTU change              */
+	unsigned long rx_over_errors;	/* Frame bigger then STRIP buf. */
+
+	unsigned long pps_timer;	/* Timer to determine pps       */
+	unsigned long rx_pps_count;	/* Counter to determine pps     */
+	unsigned long tx_pps_count;	/* Counter to determine pps     */
+	unsigned long sx_pps_count;	/* Counter to determine pps     */
+	unsigned long rx_average_pps;	/* rx packets per second * 8    */
+	unsigned long tx_average_pps;	/* tx packets per second * 8    */
+	unsigned long sx_average_pps;	/* sent packets per second * 8  */
+
+#ifdef EXT_COUNTERS
+	unsigned long rx_bytes;		/* total received bytes */
+	unsigned long tx_bytes;		/* total received bytes */
+	unsigned long rx_rbytes;	/* bytes thru radio i/f */
+	unsigned long tx_rbytes;	/* bytes thru radio i/f */
+	unsigned long rx_sbytes;	/* tot bytes thru serial i/f */
+	unsigned long tx_sbytes;	/* tot bytes thru serial i/f */
+	unsigned long rx_ebytes;	/* tot stat/err bytes */
+	unsigned long tx_ebytes;	/* tot stat/err bytes */
+#endif
+
+	/*
+	 * Internal variables.
+	 */
+
+	struct list_head  list;		/* Linked list of devices */
+
+	int discard;			/* Set if serial error          */
+	int working;			/* Is radio working correctly?  */
+	int firmware_level;		/* Message structuring level    */
+	int next_command;		/* Next periodic command        */
+	unsigned int user_baud;		/* The user-selected baud rate  */
+	int mtu;			/* Our mtu (to spot changes!)   */
+	long watchdog_doprobe;		/* Next time to test the radio  */
+	long watchdog_doreset;		/* Time to do next reset        */
+	long gratuitous_arp;		/* Time to send next ARP refresh */
+	long arp_interval;		/* Next ARP interval            */
+	struct timer_list idle_timer;	/* For periodic wakeup calls    */
+	MetricomAddress true_dev_addr;	/* True address of radio        */
+	int manual_dev_addr;		/* Hack: See note below         */
+
+	FirmwareVersion firmware_version;	/* The radio's firmware version */
+	SerialNumber serial_number;	/* The radio's serial number    */
+	BatteryVoltage battery_voltage;	/* The radio's battery voltage  */
+
+	/*
+	 * Other useful structures.
+	 */
+
+	struct tty_struct *tty;		/* ptr to TTY structure         */
+	struct net_device *dev;		/* Our device structure         */
+
+	/*
+	 * Neighbour radio records
+	 */
+
+	MetricomNodeTable portables;
+	MetricomNodeTable poletops;
+};
+
+/*
+ * Note: manual_dev_addr hack
+ * 
+ * It is not possible to change the hardware address of a Metricom radio,
+ * or to send packets with a user-specified hardware source address, thus
+ * trying to manually set a hardware source address is a questionable
+ * thing to do.  However, if the user *does* manually set the hardware
+ * source address of a STRIP interface, then the kernel will believe it,
+ * and use it in certain places. For example, the hardware address listed
+ * by ifconfig will be the manual address, not the true one.
+ * (Both addresses are listed in /proc/net/strip.)
+ * Also, ARP packets will be sent out giving the user-specified address as
+ * the source address, not the real address. This is dangerous, because
+ * it means you won't receive any replies -- the ARP replies will go to
+ * the specified address, which will be some other radio. The case where
+ * this is useful is when that other radio is also connected to the same
+ * machine. This allows you to connect a pair of radios to one machine,
+ * and to use one exclusively for inbound traffic, and the other
+ * exclusively for outbound traffic. Pretty neat, huh?
+ * 
+ * Here's the full procedure to set this up:
+ * 
+ * 1. "slattach" two interfaces, e.g. st0 for outgoing packets,
+ *    and st1 for incoming packets
+ * 
+ * 2. "ifconfig" st0 (outbound radio) to have the hardware address
+ *    which is the real hardware address of st1 (inbound radio).
+ *    Now when it sends out packets, it will masquerade as st1, and
+ *    replies will be sent to that radio, which is exactly what we want.
+ * 
+ * 3. Set the route table entry ("route add default ..." or
+ *    "route add -net ...", as appropriate) to send packets via the st0
+ *    interface (outbound radio). Do not add any route which sends packets
+ *    out via the st1 interface -- that radio is for inbound traffic only.
+ * 
+ * 4. "ifconfig" st1 (inbound radio) to have hardware address zero.
+ *    This tells the STRIP driver to "shut down" that interface and not
+ *    send any packets through it. In particular, it stops sending the
+ *    periodic gratuitous ARP packets that a STRIP interface normally sends.
+ *    Also, when packets arrive on that interface, it will search the
+ *    interface list to see if there is another interface who's manual
+ *    hardware address matches its own real address (i.e. st0 in this
+ *    example) and if so it will transfer ownership of the skbuff to
+ *    that interface, so that it looks to the kernel as if the packet
+ *    arrived on that interface. This is necessary because when the
+ *    kernel sends an ARP packet on st0, it expects to get a reply on
+ *    st0, and if it sees the reply come from st1 then it will ignore
+ *    it (to be accurate, it puts the entry in the ARP table, but
+ *    labelled in such a way that st0 can't use it).
+ * 
+ * Thanks to Petros Maniatis for coming up with the idea of splitting
+ * inbound and outbound traffic between two interfaces, which turned
+ * out to be really easy to implement, even if it is a bit of a hack.
+ * 
+ * Having set a manual address on an interface, you can restore it
+ * to automatic operation (where the address is automatically kept
+ * consistent with the real address of the radio) by setting a manual
+ * address of all ones, e.g. "ifconfig st0 hw strip FFFFFFFFFFFF"
+ * This 'turns off' manual override mode for the device address.
+ * 
+ * Note: The IEEE 802 headers reported in tcpdump will show the *real*
+ * radio addresses the packets were sent and received from, so that you
+ * can see what is really going on with packets, and which interfaces
+ * they are really going through.
+ */
+
+
+/************************************************************************/
+/* Constants								*/
+
+/*
+ * CommandString1 works on all radios
+ * Other CommandStrings are only used with firmware that provides structured responses.
+ * 
+ * ats319=1 Enables Info message for node additions and deletions
+ * ats319=2 Enables Info message for a new best node
+ * ats319=4 Enables checksums
+ * ats319=8 Enables ACK messages
+ */
+
+static const int MaxCommandStringLength = 32;
+static const int CompatibilityCommand = 1;
+
+static const char CommandString0[] = "*&COMMAND*ATS319=7";	/* Turn on checksums & info messages */
+static const char CommandString1[] = "*&COMMAND*ATS305?";	/* Query radio name */
+static const char CommandString2[] = "*&COMMAND*ATS325?";	/* Query battery voltage */
+static const char CommandString3[] = "*&COMMAND*ATS300?";	/* Query version information */
+static const char CommandString4[] = "*&COMMAND*ATS311?";	/* Query poletop list */
+static const char CommandString5[] = "*&COMMAND*AT~LA";		/* Query portables list */
+typedef struct {
+	const char *string;
+	long length;
+} StringDescriptor;
+
+static const StringDescriptor CommandString[] = {
+	{CommandString0, sizeof(CommandString0) - 1},
+	{CommandString1, sizeof(CommandString1) - 1},
+	{CommandString2, sizeof(CommandString2) - 1},
+	{CommandString3, sizeof(CommandString3) - 1},
+	{CommandString4, sizeof(CommandString4) - 1},
+	{CommandString5, sizeof(CommandString5) - 1}
+};
+
+#define GOT_ALL_RADIO_INFO(S)      \
+    ((S)->firmware_version.c[0] && \
+     (S)->battery_voltage.c[0]  && \
+     memcmp(&(S)->true_dev_addr, zero_address.c, sizeof(zero_address)))
+
+static const char hextable[16] = "0123456789ABCDEF";
+
+static const MetricomAddress zero_address;
+static const MetricomAddress broadcast_address =
+    { {0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF} };
+
+static const MetricomKey SIP0Key = { "SIP0" };
+static const MetricomKey ARP0Key = { "ARP0" };
+static const MetricomKey ATR_Key = { "ATR " };
+static const MetricomKey ACK_Key = { "ACK_" };
+static const MetricomKey INF_Key = { "INF_" };
+static const MetricomKey ERR_Key = { "ERR_" };
+
+static const long MaxARPInterval = 60 * HZ;	/* One minute */
+
+/*
+ * Maximum Starmode packet length is 1183 bytes. Allowing 4 bytes for
+ * protocol key, 4 bytes for checksum, one byte for CR, and 65/64 expansion
+ * for STRIP encoding, that translates to a maximum payload MTU of 1155.
+ * Note: A standard NFS 1K data packet is a total of 0x480 (1152) bytes
+ * long, including IP header, UDP header, and NFS header. Setting the STRIP
+ * MTU to 1152 allows us to send default sized NFS packets without fragmentation.
+ */
+static const unsigned short MAX_SEND_MTU = 1152;
+static const unsigned short MAX_RECV_MTU = 1500;	/* Hoping for Ethernet sized packets in the future! */
+static const unsigned short DEFAULT_STRIP_MTU = 1152;
+static const int STRIP_MAGIC = 0x5303;
+static const long LongTime = 0x7FFFFFFF;
+
+/************************************************************************/
+/* Global variables							*/
+
+static LIST_HEAD(strip_list);
+static DEFINE_SPINLOCK(strip_lock);
+
+/************************************************************************/
+/* Macros								*/
+
+/* Returns TRUE if text T begins with prefix P */
+#define has_prefix(T,L,P) (((L) >= sizeof(P)-1) && !strncmp((T), (P), sizeof(P)-1))
+
+/* Returns TRUE if text T of length L is equal to string S */
+#define text_equal(T,L,S) (((L) == sizeof(S)-1) && !strncmp((T), (S), sizeof(S)-1))
+
+#define READHEX(X) ((X)>='0' && (X)<='9' ? (X)-'0' :      \
+                    (X)>='a' && (X)<='f' ? (X)-'a'+10 :   \
+                    (X)>='A' && (X)<='F' ? (X)-'A'+10 : 0 )
+
+#define READHEX16(X) ((__u16)(READHEX(X)))
+
+#define READDEC(X) ((X)>='0' && (X)<='9' ? (X)-'0' : 0)
+
+#define ARRAY_END(X) (&((X)[ARRAY_SIZE(X)]))
+
+#define JIFFIE_TO_SEC(X) ((X) / HZ)
+
+
+/************************************************************************/
+/* Utility routines							*/
+
+static int arp_query(unsigned char *haddr, u32 paddr,
+		     struct net_device *dev)
+{
+	struct neighbour *neighbor_entry;
+	int ret = 0;
+
+	neighbor_entry = neigh_lookup(&arp_tbl, &paddr, dev);
+
+	if (neighbor_entry != NULL) {
+		neighbor_entry->used = jiffies;
+		if (neighbor_entry->nud_state & NUD_VALID) {
+			memcpy(haddr, neighbor_entry->ha, dev->addr_len);
+			ret = 1;
+		}
+		neigh_release(neighbor_entry);
+	}
+	return ret;
+}
+
+static void DumpData(char *msg, struct strip *strip_info, __u8 * ptr,
+		     __u8 * end)
+{
+	static const int MAX_DumpData = 80;
+	__u8 pkt_text[MAX_DumpData], *p = pkt_text;
+
+	*p++ = '\"';
+
+	while (ptr < end && p < &pkt_text[MAX_DumpData - 4]) {
+		if (*ptr == '\\') {
+			*p++ = '\\';
+			*p++ = '\\';
+		} else {
+			if (*ptr >= 32 && *ptr <= 126) {
+				*p++ = *ptr;
+			} else {
+				sprintf(p, "\\%02X", *ptr);
+				p += 3;
+			}
+		}
+		ptr++;
+	}
+
+	if (ptr == end)
+		*p++ = '\"';
+	*p++ = 0;
+
+	printk(KERN_INFO "%s: %-13s%s\n", strip_info->dev->name, msg, pkt_text);
+}
+
+
+/************************************************************************/
+/* Byte stuffing/unstuffing routines					*/
+
+/* Stuffing scheme:
+ * 00    Unused (reserved character)
+ * 01-3F Run of 2-64 different characters
+ * 40-7F Run of 1-64 different characters plus a single zero at the end
+ * 80-BF Run of 1-64 of the same character
+ * C0-FF Run of 1-64 zeroes (ASCII 0)
+ */
+
+typedef enum {
+	Stuff_Diff = 0x00,
+	Stuff_DiffZero = 0x40,
+	Stuff_Same = 0x80,
+	Stuff_Zero = 0xC0,
+	Stuff_NoCode = 0xFF,	/* Special code, meaning no code selected */
+
+	Stuff_CodeMask = 0xC0,
+	Stuff_CountMask = 0x3F,
+	Stuff_MaxCount = 0x3F,
+	Stuff_Magic = 0x0D	/* The value we are eliminating */
+} StuffingCode;
+
+/* StuffData encodes the data starting at "src" for "length" bytes.
+ * It writes it to the buffer pointed to by "dst" (which must be at least
+ * as long as 1 + 65/64 of the input length). The output may be up to 1.6%
+ * larger than the input for pathological input, but will usually be smaller.
+ * StuffData returns the new value of the dst pointer as its result.
+ * "code_ptr_ptr" points to a "__u8 *" which is used to hold encoding state
+ * between calls, allowing an encoded packet to be incrementally built up
+ * from small parts. On the first call, the "__u8 *" pointed to should be
+ * initialized to NULL; between subsequent calls the calling routine should
+ * leave the value alone and simply pass it back unchanged so that the
+ * encoder can recover its current state.
+ */
+
+#define StuffData_FinishBlock(X) \
+(*code_ptr = (X) ^ Stuff_Magic, code = Stuff_NoCode)
+
+static __u8 *StuffData(__u8 * src, __u32 length, __u8 * dst,
+		       __u8 ** code_ptr_ptr)
+{
+	__u8 *end = src + length;
+	__u8 *code_ptr = *code_ptr_ptr;
+	__u8 code = Stuff_NoCode, count = 0;
+
+	if (!length)
+		return (dst);
+
+	if (code_ptr) {
+		/*
+		 * Recover state from last call, if applicable
+		 */
+		code = (*code_ptr ^ Stuff_Magic) & Stuff_CodeMask;
+		count = (*code_ptr ^ Stuff_Magic) & Stuff_CountMask;
+	}
+
+	while (src < end) {
+		switch (code) {
+			/* Stuff_NoCode: If no current code, select one */
+		case Stuff_NoCode:
+			/* Record where we're going to put this code */
+			code_ptr = dst++;
+			count = 0;	/* Reset the count (zero means one instance) */
+			/* Tentatively start a new block */
+			if (*src == 0) {
+				code = Stuff_Zero;
+				src++;
+			} else {
+				code = Stuff_Same;
+				*dst++ = *src++ ^ Stuff_Magic;
+			}
+			/* Note: We optimistically assume run of same -- */
+			/* which will be fixed later in Stuff_Same */
+			/* if it turns out not to be true. */
+			break;
+
+			/* Stuff_Zero: We already have at least one zero encoded */
+		case Stuff_Zero:
+			/* If another zero, count it, else finish this code block */
+			if (*src == 0) {
+				count++;
+				src++;
+			} else {
+				StuffData_FinishBlock(Stuff_Zero + count);
+			}
+			break;
+
+			/* Stuff_Same: We already have at least one byte encoded */
+		case Stuff_Same:
+			/* If another one the same, count it */
+			if ((*src ^ Stuff_Magic) == code_ptr[1]) {
+				count++;
+				src++;
+				break;
+			}
+			/* else, this byte does not match this block. */
+			/* If we already have two or more bytes encoded, finish this code block */
+			if (count) {
+				StuffData_FinishBlock(Stuff_Same + count);
+				break;
+			}
+			/* else, we only have one so far, so switch to Stuff_Diff code */
+			code = Stuff_Diff;
+			/* and fall through to Stuff_Diff case below
+			 * Note cunning cleverness here: case Stuff_Diff compares 
+			 * the current character with the previous two to see if it
+			 * has a run of three the same. Won't this be an error if
+			 * there aren't two previous characters stored to compare with?
+			 * No. Because we know the current character is *not* the same
+			 * as the previous one, the first test below will necessarily
+			 * fail and the send half of the "if" won't be executed.
+			 */
+
+			/* Stuff_Diff: We have at least two *different* bytes encoded */
+		case Stuff_Diff:
+			/* If this is a zero, must encode a Stuff_DiffZero, and begin a new block */
+			if (*src == 0) {
+				StuffData_FinishBlock(Stuff_DiffZero +
+						      count);
+			}
+			/* else, if we have three in a row, it is worth starting a Stuff_Same block */
+			else if ((*src ^ Stuff_Magic) == dst[-1]
+				 && dst[-1] == dst[-2]) {
+				/* Back off the last two characters we encoded */
+				code += count - 2;
+				/* Note: "Stuff_Diff + 0" is an illegal code */
+				if (code == Stuff_Diff + 0) {
+					code = Stuff_Same + 0;
+				}
+				StuffData_FinishBlock(code);
+				code_ptr = dst - 2;
+				/* dst[-1] already holds the correct value */
+				count = 2;	/* 2 means three bytes encoded */
+				code = Stuff_Same;
+			}
+			/* else, another different byte, so add it to the block */
+			else {
+				*dst++ = *src ^ Stuff_Magic;
+				count++;
+			}
+			src++;	/* Consume the byte */
+			break;
+		}
+		if (count == Stuff_MaxCount) {
+			StuffData_FinishBlock(code + count);
+		}
+	}
+	if (code == Stuff_NoCode) {
+		*code_ptr_ptr = NULL;
+	} else {
+		*code_ptr_ptr = code_ptr;
+		StuffData_FinishBlock(code + count);
+	}
+	return (dst);
+}
+
+/*
+ * UnStuffData decodes the data at "src", up to (but not including) "end".
+ * It writes the decoded data into the buffer pointed to by "dst", up to a
+ * maximum of "dst_length", and returns the new value of "src" so that a
+ * follow-on call can read more data, continuing from where the first left off.
+ * 
+ * There are three types of results:
+ * 1. The source data runs out before extracting "dst_length" bytes:
+ *    UnStuffData returns NULL to indicate failure.
+ * 2. The source data produces exactly "dst_length" bytes:
+ *    UnStuffData returns new_src = end to indicate that all bytes were consumed.
+ * 3. "dst_length" bytes are extracted, with more remaining.
+ *    UnStuffData returns new_src < end to indicate that there are more bytes
+ *    to be read.
+ * 
+ * Note: The decoding may be destructive, in that it may alter the source
+ * data in the process of decoding it (this is necessary to allow a follow-on
+ * call to resume correctly).
+ */
+
+static __u8 *UnStuffData(__u8 * src, __u8 * end, __u8 * dst,
+			 __u32 dst_length)
+{
+	__u8 *dst_end = dst + dst_length;
+	/* Sanity check */
+	if (!src || !end || !dst || !dst_length)
+		return (NULL);
+	while (src < end && dst < dst_end) {
+		int count = (*src ^ Stuff_Magic) & Stuff_CountMask;
+		switch ((*src ^ Stuff_Magic) & Stuff_CodeMask) {
+		case Stuff_Diff:
+			if (src + 1 + count >= end)
+				return (NULL);
+			do {
+				*dst++ = *++src ^ Stuff_Magic;
+			}
+			while (--count >= 0 && dst < dst_end);
+			if (count < 0)
+				src += 1;
+			else {
+				if (count == 0)
+					*src = Stuff_Same ^ Stuff_Magic;
+				else
+					*src =
+					    (Stuff_Diff +
+					     count) ^ Stuff_Magic;
+			}
+			break;
+		case Stuff_DiffZero:
+			if (src + 1 + count >= end)
+				return (NULL);
+			do {
+				*dst++ = *++src ^ Stuff_Magic;
+			}
+			while (--count >= 0 && dst < dst_end);
+			if (count < 0)
+				*src = Stuff_Zero ^ Stuff_Magic;
+			else
+				*src =
+				    (Stuff_DiffZero + count) ^ Stuff_Magic;
+			break;
+		case Stuff_Same:
+			if (src + 1 >= end)
+				return (NULL);
+			do {
+				*dst++ = src[1] ^ Stuff_Magic;
+			}
+			while (--count >= 0 && dst < dst_end);
+			if (count < 0)
+				src += 2;
+			else
+				*src = (Stuff_Same + count) ^ Stuff_Magic;
+			break;
+		case Stuff_Zero:
+			do {
+				*dst++ = 0;
+			}
+			while (--count >= 0 && dst < dst_end);
+			if (count < 0)
+				src += 1;
+			else
+				*src = (Stuff_Zero + count) ^ Stuff_Magic;
+			break;
+		}
+	}
+	if (dst < dst_end)
+		return (NULL);
+	else
+		return (src);
+}
+
+
+/************************************************************************/
+/* General routines for STRIP						*/
+
+/*
+ * set_baud sets the baud rate to the rate defined by baudcode
+ */
+static void set_baud(struct tty_struct *tty, speed_t baudrate)
+{
+	struct ktermios old_termios;
+
+	mutex_lock(&tty->termios_mutex);
+	old_termios =*(tty->termios);
+	tty_encode_baud_rate(tty, baudrate, baudrate);
+	tty->ops->set_termios(tty, &old_termios);
+	mutex_unlock(&tty->termios_mutex);
+}
+
+/*
+ * Convert a string to a Metricom Address.
+ */
+
+#define IS_RADIO_ADDRESS(p) (                                                 \
+  isdigit((p)[0]) && isdigit((p)[1]) && isdigit((p)[2]) && isdigit((p)[3]) && \
+  (p)[4] == '-' &&                                                            \
+  isdigit((p)[5]) && isdigit((p)[6]) && isdigit((p)[7]) && isdigit((p)[8])    )
+
+static int string_to_radio_address(MetricomAddress * addr, __u8 * p)
+{
+	if (!IS_RADIO_ADDRESS(p))
+		return (1);
+	addr->c[0] = 0;
+	addr->c[1] = 0;
+	addr->c[2] = READHEX(p[0]) << 4 | READHEX(p[1]);
+	addr->c[3] = READHEX(p[2]) << 4 | READHEX(p[3]);
+	addr->c[4] = READHEX(p[5]) << 4 | READHEX(p[6]);
+	addr->c[5] = READHEX(p[7]) << 4 | READHEX(p[8]);
+	return (0);
+}
+
+/*
+ * Convert a Metricom Address to a string.
+ */
+
+static __u8 *radio_address_to_string(const MetricomAddress * addr,
+				     MetricomAddressString * p)
+{
+	sprintf(p->c, "%02X%02X-%02X%02X", addr->c[2], addr->c[3],
+		addr->c[4], addr->c[5]);
+	return (p->c);
+}
+
+/*
+ * Note: Must make sure sx_size is big enough to receive a stuffed
+ * MAX_RECV_MTU packet. Additionally, we also want to ensure that it's
+ * big enough to receive a large radio neighbour list (currently 4K).
+ */
+
+static int allocate_buffers(struct strip *strip_info, int mtu)
+{
+	struct net_device *dev = strip_info->dev;
+	int sx_size = max_t(int, STRIP_ENCAP_SIZE(MAX_RECV_MTU), 4096);
+	int tx_size = STRIP_ENCAP_SIZE(mtu) + MaxCommandStringLength;
+	__u8 *r = kmalloc(MAX_RECV_MTU, GFP_ATOMIC);
+	__u8 *s = kmalloc(sx_size, GFP_ATOMIC);
+	__u8 *t = kmalloc(tx_size, GFP_ATOMIC);
+	if (r && s && t) {
+		strip_info->rx_buff = r;
+		strip_info->sx_buff = s;
+		strip_info->tx_buff = t;
+		strip_info->sx_size = sx_size;
+		strip_info->tx_size = tx_size;
+		strip_info->mtu = dev->mtu = mtu;
+		return (1);
+	}
+	kfree(r);
+	kfree(s);
+	kfree(t);
+	return (0);
+}
+
+/*
+ * MTU has been changed by the IP layer. 
+ * We could be in
+ * an upcall from the tty driver, or in an ip packet queue.
+ */
+static int strip_change_mtu(struct net_device *dev, int new_mtu)
+{
+	struct strip *strip_info = netdev_priv(dev);
+	int old_mtu = strip_info->mtu;
+	unsigned char *orbuff = strip_info->rx_buff;
+	unsigned char *osbuff = strip_info->sx_buff;
+	unsigned char *otbuff = strip_info->tx_buff;
+
+	if (new_mtu > MAX_SEND_MTU) {
+		printk(KERN_ERR
+		       "%s: MTU exceeds maximum allowable (%d), MTU change cancelled.\n",
+		       strip_info->dev->name, MAX_SEND_MTU);
+		return -EINVAL;
+	}
+
+	spin_lock_bh(&strip_lock);
+	if (!allocate_buffers(strip_info, new_mtu)) {
+		printk(KERN_ERR "%s: unable to grow strip buffers, MTU change cancelled.\n",
+		       strip_info->dev->name);
+		spin_unlock_bh(&strip_lock);
+		return -ENOMEM;
+	}
+
+	if (strip_info->sx_count) {
+		if (strip_info->sx_count <= strip_info->sx_size)
+			memcpy(strip_info->sx_buff, osbuff,
+			       strip_info->sx_count);
+		else {
+			strip_info->discard = strip_info->sx_count;
+			strip_info->rx_over_errors++;
+		}
+	}
+
+	if (strip_info->tx_left) {
+		if (strip_info->tx_left <= strip_info->tx_size)
+			memcpy(strip_info->tx_buff, strip_info->tx_head,
+			       strip_info->tx_left);
+		else {
+			strip_info->tx_left = 0;
+			strip_info->tx_dropped++;
+		}
+	}
+	strip_info->tx_head = strip_info->tx_buff;
+	spin_unlock_bh(&strip_lock);
+
+	printk(KERN_NOTICE "%s: strip MTU changed fom %d to %d.\n",
+	       strip_info->dev->name, old_mtu, strip_info->mtu);
+
+	kfree(orbuff);
+	kfree(osbuff);
+	kfree(otbuff);
+	return 0;
+}
+
+static void strip_unlock(struct strip *strip_info)
+{
+	/*
+	 * Set the timer to go off in one second.
+	 */
+	strip_info->idle_timer.expires = jiffies + 1 * HZ;
+	add_timer(&strip_info->idle_timer);
+	netif_wake_queue(strip_info->dev);
+}
+
+
+
+/*
+ * If the time is in the near future, time_delta prints the number of
+ * seconds to go into the buffer and returns the address of the buffer.
+ * If the time is not in the near future, it returns the address of the
+ * string "Not scheduled" The buffer must be long enough to contain the
+ * ascii representation of the number plus 9 charactes for the " seconds"
+ * and the null character.
+ */
+#ifdef CONFIG_PROC_FS
+static char *time_delta(char buffer[], long time)
+{
+	time -= jiffies;
+	if (time > LongTime / 2)
+		return ("Not scheduled");
+	if (time < 0)
+		time = 0;	/* Don't print negative times */
+	sprintf(buffer, "%ld seconds", time / HZ);
+	return (buffer);
+}
+
+/* get Nth element of the linked list */
+static struct strip *strip_get_idx(loff_t pos) 
+{
+	struct strip *str;
+	int i = 0;
+
+	list_for_each_entry_rcu(str, &strip_list, list) {
+		if (pos == i)
+			return str;
+		++i;
+	}
+	return NULL;
+}
+
+static void *strip_seq_start(struct seq_file *seq, loff_t *pos)
+{
+	rcu_read_lock();
+	return *pos ? strip_get_idx(*pos - 1) : SEQ_START_TOKEN;
+}
+
+static void *strip_seq_next(struct seq_file *seq, void *v, loff_t *pos)
+{
+	struct list_head *l;
+	struct strip *s;
+
+	++*pos;
+	if (v == SEQ_START_TOKEN)
+		return strip_get_idx(1);
+
+	s = v;
+	l = &s->list;
+	list_for_each_continue_rcu(l, &strip_list) {
+		return list_entry(l, stru