Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "These are changes for drivers that are intimately tied to some SoC and
  for some reason could not get merged through the respective subsystem
  maintainer tree.

  Most of the new code is for the Keystone Navigator driver, which is
  new base support that is going to be needed for their hardware
  accelerated network driver and other units.

  Most of the commits are for moving old code around from at91 and omap
  for things that are done in device drivers nowadays.

   - at91: move reset, poweroff, memory and clocksource code into
     drivers directories
   - socfpga: add edac driver (through arm-soc, as requested by Boris)
   - omap: move omap-intc code to drivers/irqchip
   - sunxi: added an RTC driver for sun6i
   - omap: mailbox driver related changes
   - keystone: support for the "Navigator" component
   - versatile: new reboot, led and soc drivers"

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
  bus: arm-ccn: Fix spurious warning message
  leds: add device tree bindings for register bit LEDs
  soc: add driver for the ARM RealView
  power: reset: driver for the Versatile syscon reboot
  leds: add a driver for syscon-based LEDs
  drivers/soc: ti: fix build break with modules
  MAINTAINERS: Add Keystone Multicore Navigator drivers entry
  soc: ti: add Keystone Navigator DMA support
  Documentation: dt: soc: add Keystone Navigator DMA bindings
  soc: ti: add Keystone Navigator QMSS driver
  Documentation: dt: soc: add Keystone Navigator QMSS bindings
  rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
  rtc: sun6i: Add sun6i RTC driver
  irqchip: omap-intc: remove unnecessary comments
  irqchip: omap-intc: correct maximum number or MIR registers
  irqchip: omap-intc: enable TURBO idle mode
  irqchip: omap-intc: enable IP protection
  irqchip: omap-intc: remove unnecesary of_address_to_resource() call
  irqchip: omap-intc: comment style cleanup
  irqchip: omap-intc: minor improvement to omap_irq_pending()
  ...

108 files changed, 7609 insertions, 1299 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
index 4949e805f7fc..562cda9d86d9 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -98,8 +98,8 @@ RAMC SDRAM/DDR Controller required properties:
 - compatible: Should be "atmel,at91rm9200-sdramc",
 			"atmel,at91sam9260-sdramc",
 			"atmel,at91sam9g45-ddramc",
+			"atmel,sama5d3-ddramc",
 - reg: Should contain registers location and length
-  For at91sam9263 and at91sam9g45 you must specify 2 entries.
 
 Examples:
 
@@ -108,12 +108,6 @@ Examples:
 		reg = <0xffffe800 0x200>;
 	};
 
-	ramc0: ramc@ffffe400 {
-		compatible = "atmel,at91sam9g45-ddramc";
-		reg = <0xffffe400 0x200
-		       0xffffe600 0x200>;
-	};
-
 SHDWC Shutdown Controller
 
 required properties:
diff --git a/Documentation/devicetree/bindings/leds/register-bit-led.txt b/Documentation/devicetree/bindings/leds/register-bit-led.txt
new file mode 100644
index 000000000000..379cefdc0bda
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/register-bit-led.txt
@@ -0,0 +1,99 @@
+Device Tree Bindings for Register Bit LEDs
+
+Register bit leds are used with syscon multifunctional devices
+where single bits in a certain register can turn on/off a
+single LED. The register bit LEDs appear as children to the
+syscon device, with the proper compatible string. For the
+syscon bindings see:
+Documentation/devicetree/bindings/mfd/syscon.txt
+
+Each LED is represented as a sub-node of the syscon device. Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+
+Required properties:
+- compatible : must be "register-bit-led"
+- offset : register offset to the register controlling this LED
+- mask : bit mask for the bit controlling this LED in the register
+  typically 0x01, 0x02, 0x04 ...
+
+Optional properties:
+- label : (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger : (optional)
+  see Documentation/devicetree/bindings/leds/common.txt
+- default-state: (optional) The initial state of the LED. Valid
+  values are "on", "off", and "keep". If the LED is already on or off
+  and the default-state property is set the to same value, then no
+  glitch should be produced where the LED momentarily turns off (or
+  on). The "keep" setting will keep the LED at whatever its current
+  state is, without producing a glitch.  The default is off if this
+  property is not present.
+
+Example:
+
+syscon: syscon@10000000 {
+	compatible = "arm,realview-pb1176-syscon", "syscon";
+	reg = <0x10000000 0x1000>;
+
+	led@08.0 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x01>;
+		label = "versatile:0";
+		linux,default-trigger = "heartbeat";
+		default-state = "on";
+	};
+	led@08.1 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x02>;
+		label = "versatile:1";
+		linux,default-trigger = "mmc0";
+		default-state = "off";
+	};
+	led@08.2 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x04>;
+		label = "versatile:2";
+		linux,default-trigger = "cpu0";
+		default-state = "off";
+	};
+	led@08.3 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x08>;
+		label = "versatile:3";
+		default-state = "off";
+	};
+	led@08.4 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x10>;
+		label = "versatile:4";
+		default-state = "off";
+	};
+	led@08.5 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x20>;
+		label = "versatile:5";
+		default-state = "off";
+	};
+	led@08.6 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x40>;
+		label = "versatile:6";
+		default-state = "off";
+	};
+	led@08.7 {
+		compatible = "register-bit-led";
+		offset = <0x08>;
+		mask = <0x80>;
+		label = "versatile:7";
+		default-state = "off";
+	};
+};
diff --git a/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt
new file mode 100644
index 000000000000..48edc4b92afb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mailbox/omap-mailbox.txt
@@ -0,0 +1,108 @@
+OMAP2+ Mailbox Driver
+=====================
+
+The OMAP mailbox hardware facilitates communication between different processors
+using a queued mailbox interrupt mechanism. The IP block is external to the
+various processor subsystems and is connected on an interconnect bus. The
+communication is achieved through a set of registers for message storage and
+interrupt configuration registers.
+
+Each mailbox IP block has a certain number of h/w fifo queues and output
+interrupt lines. An output interrupt line is routed to an interrupt controller
+within a processor subsystem, and there can be more than one line going to a
+specific processor's interrupt controller. The interrupt line connections are
+fixed for an instance and are dictated by the IP integration into the SoC
+(excluding the SoCs that have a Interrupt Crossbar IP). Each interrupt line is
+programmable through a set of interrupt configuration registers, and have a rx
+and tx interrupt source per h/w fifo. Communication between different processors
+is achieved through the appropriate programming of the rx and tx interrupt
+sources on the appropriate interrupt lines.
+
+The number of h/w fifo queues and interrupt lines dictate the usable registers.
+All the current OMAP SoCs except for the newest DRA7xx SoC has a single IP
+instance. DRA7xx has multiple instances with different number of h/w fifo queues
+and interrupt lines between different instances. The interrupt lines can also be
+routed to different processor sub-systems on DRA7xx as they are routed through
+the Crossbar, a kind of interrupt router/multiplexer.
+
+Mailbox Device Node:
+====================
+A Mailbox device node is used to represent a Mailbox IP instance within a SoC.
+The sub-mailboxes are represented as child nodes of this parent node.
+
+Required properties:
+--------------------
+- compatible:		Should be one of the following,
+			    "ti,omap2-mailbox" for OMAP2420, OMAP2430 SoCs
+			    "ti,omap3-mailbox" for OMAP3430, OMAP3630 SoCs
+			    "ti,omap4-mailbox" for OMAP44xx, OMAP54xx, AM33xx,
+						   AM43xx and DRA7xx SoCs
+- reg:			Contains the mailbox register address range (base
+			address and length)
+- interrupts:		Contains the interrupt information for the mailbox
+			device. The format is dependent on which interrupt
+			controller the OMAP device uses
+- ti,hwmods:		Name of the hwmod associated with the mailbox
+- ti,mbox-num-users:	Number of targets (processor devices) that the mailbox
+			device can interrupt
+- ti,mbox-num-fifos:	Number of h/w fifo queues within the mailbox IP block
+
+Child Nodes:
+============
+A child node is used for representing the actual sub-mailbox device that is
+used for the communication between the host processor and a remote processor.
+Each child node should have a unique node name across all the different
+mailbox device nodes.
+
+Required properties:
+--------------------
+- ti,mbox-tx:		sub-mailbox descriptor property defining a Tx fifo
+- ti,mbox-rx:		sub-mailbox descriptor property defining a Rx fifo