Merge refs/heads/upstream from master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6.git

30 files changed, 11159 insertions, 90 deletions

diff --git a/Documentation/networking/cxgb.txt b/Documentation/networking/cxgb.txt
new file mode 100644
index 000000000000..76324638626b
--- /dev/null
+++ b/Documentation/networking/cxgb.txt
@@ -0,0 +1,352 @@
+                 Chelsio N210 10Gb Ethernet Network Controller
+
+                         Driver Release Notes for Linux
+
+                                 Version 2.1.1
+
+                                 June 20, 2005
+
+CONTENTS
+========
+ INTRODUCTION
+ FEATURES
+ PERFORMANCE
+ DRIVER MESSAGES
+ KNOWN ISSUES
+ SUPPORT
+
+
+INTRODUCTION
+============
+
+ This document describes the Linux driver for Chelsio 10Gb Ethernet Network
+ Controller. This driver supports the Chelsio N210 NIC and is backward
+ compatible with the Chelsio N110 model 10Gb NICs.
+
+
+FEATURES
+========
+
+ Adaptive Interrupts (adaptive-rx)
+ ---------------------------------
+
+  This feature provides an adaptive algorithm that adjusts the interrupt
+  coalescing parameters, allowing the driver to dynamically adapt the latency
+  settings to achieve the highest performance during various types of network
+  load.
+
+  The interface used to control this feature is ethtool. Please see the
+  ethtool manpage for additional usage information.
+
+  By default, adaptive-rx is disabled.
+  To enable adaptive-rx:
+
+      ethtool -C <interface> adaptive-rx on
+
+  To disable adaptive-rx, use ethtool:
+
+      ethtool -C <interface> adaptive-rx off
+
+  After disabling adaptive-rx, the timer latency value will be set to 50us.
+  You may set the timer latency after disabling adaptive-rx:
+
+      ethtool -C <interface> rx-usecs <microseconds>
+
+  An example to set the timer latency value to 100us on eth0:
+
+      ethtool -C eth0 rx-usecs 100
+
+  You may also provide a timer latency value while disabling adpative-rx:
+
+      ethtool -C <interface> adaptive-rx off rx-usecs <microseconds>
+
+  If adaptive-rx is disabled and a timer latency value is specified, the timer
+  will be set to the specified value until changed by the user or until
+  adaptive-rx is enabled.
+
+  To view the status of the adaptive-rx and timer latency values:
+
+      ethtool -c <interface>
+
+
+ TCP Segmentation Offloading (TSO) Support
+ -----------------------------------------
+
+  This feature, also known as "large send", enables a system's protocol stack
+  to offload portions of outbound TCP processing to a network interface card
+  thereby reducing system CPU utilization and enhancing performance.
+
+  The interface used to control this feature is ethtool version 1.8 or higher.
+  Please see the ethtool manpage for additional usage information.
+
+  By default, TSO is enabled.
+  To disable TSO:
+
+      ethtool -K <interface> tso off
+
+  To enable TSO:
+
+      ethtool -K <interface> tso on
+
+  To view the status of TSO:
+
+      ethtool -k <interface>
+
+
+PERFORMANCE
+===========
+
+ The following information is provided as an example of how to change system
+ parameters for "performance tuning" an what value to use. You may or may not
+ want to change these system parameters, depending on your server/workstation
+ application. Doing so is not warranted in any way by Chelsio Communications,
+ and is done at "YOUR OWN RISK". Chelsio will not be held responsible for loss
+ of data or damage to equipment.
+
+ Your distribution may have a different way of doing things, or you may prefer
+ a different method. These commands are shown only to provide an example of
+ what to do and are by no means definitive.
+
+ Making any of the following system changes will only last until you reboot
+ your system. You may want to write a script that runs at boot-up which
+ includes the optimal settings for your system.
+
+  Setting PCI Latency Timer:
+      setpci -d 1425:* 0x0c.l=0x0000F800
+
+  Disabling TCP timestamp:
+      sysctl -w net.ipv4.tcp_timestamps=0
+
+  Disabling SACK:
+      sysctl -w net.ipv4.tcp_sack=0
+
+  Setting large number of incoming connection requests:
+      sysctl -w net.ipv4.tcp_max_syn_backlog=3000
+
+  Setting maximum receive socket buffer size:
+      sysctl -w net.core.rmem_max=1024000
+
+  Setting maximum send socket buffer size:
+      sysctl -w net.core.wmem_max=1024000
+
+  Set smp_affinity (on a multiprocessor system) to a single CPU:
+      echo 1 > /proc/irq/<interrupt_number>/smp_affinity
+
+  Setting default receive socket buffer size:
+      sysctl -w net.core.rmem_default=524287
+
+  Setting default send socket buffer size:
+      sysctl -w net.core.wmem_default=524287
+
+  Setting maximum option memory buffers:
+      sysctl -w net.core.optmem_max=524287
+
+  Setting maximum backlog (# of unprocessed packets before kernel drops):
+      sysctl -w net.core.netdev_max_backlog=300000
+
+  Setting TCP read buffers (min/default/max):
+      sysctl -w net.ipv4.tcp_rmem="10000000 10000000 10000000"
+
+  Setting TCP write buffers (min/pressure/max):
+      sysctl -w net.ipv4.tcp_wmem="10000000 10000000 10000000"
+
+  Setting TCP buffer space (min/pressure/max):
+      sysctl -w net.ipv4.tcp_mem="10000000 10000000 10000000"
+
+  TCP window size for single connections:
+   The receive buffer (RX_WINDOW) size must be at least as large as the
+   Bandwidth-Delay Product of the communication link between the sender and
+   receiver. Due to the variations of RTT, you may want to increase the buffer
+   size up to 2 times the Bandwidth-Delay Product. Reference page 289 of
+   "TCP/IP Illustrated, Volume 1, The Protocols" by W. Richard Stevens.
+   At 10Gb speeds, use the following formula:
+       RX_WINDOW >= 1.25MBytes * RTT(in milliseconds)
+       Example for RTT with 100us: RX_WINDOW = (1,250,000 * 0.1) = 125,000
+   RX_WINDOW sizes of 256KB - 512KB should be sufficient.
+   Setting the min, max, and default receive buffer (RX_WINDOW) size:
+       sysctl -w net.ipv4.tcp_rmem="<min> <default> <max>"
+
+  TCP window size for multiple connections:
+   The receive buffer (RX_WINDOW) size may be calculated the same as single
+   connections, but should be divided by the number of connections. The
+   smaller window prevents congestion and facilitates better pacing,
+   especially if/when MAC level flow control does not work well or when it is
+   not supported on the machine. Experimentation may be necessary to attain
+   the correct value. This method is provided as a starting point fot the
+   correct receive buffer size.
+   Setting the min, max, and default receive buffer (RX_WINDOW) size is
+   performed in the same manner as single connection.
+
+
+DRIVER MESSAGES
+===============
+
+ The following messages are the most common messages logged by syslog. These
+ may be found in /var/log/messages.
+
+  Driver up:
+     Chelsio Network Driver - version 2.1.1
+
+  NIC detected:
+     eth#: Chelsio N210 1x10GBaseX NIC (rev #), PCIX 133MHz/64-bit
+
+  Link up:
+     eth#: link is up at 10 Gbps, full duplex
+
+  Link down:
+     eth#: link is down
+
+
+KNOWN ISSUES
+============
+
+ These issues have been identified during testing. The following information
+ is provided as a workaround to the problem. In some cases, this problem is
+ inherent to Linux or to a particular Linux Distribution and/or hardware
+ platform.
+
+  1. Large number of TCP retransmits on a multiprocessor (SMP) system.
+
+      On a system with multiple CPUs, the interrupt (IRQ) for the network
+      controller may be bound to more than one CPU. This will cause TCP
+      retransmits if the packet data were to be split across different CPUs
+      and re-assembled in a different order than expected.
+
+      To eliminate the TCP retransmits, set smp_affinity on the particular
+      interrupt to a single CPU. You can locate the interrupt (IRQ) used on
+      the N110/N210 by using ifconfig:
+          ifconfig <dev_name> | grep Interrupt
+      Set the smp_affinity to a single CPU:
+          echo 1 > /proc/irq/<interrupt_number>/smp_affinity
+
+      It is highly suggested that you do not run the irqbalance daemon on your
+      system, as this will change any smp_affinity setting you have applied.
+      The irqbalance daemon runs on a 10 second interval and binds interrupts
+      to the least loaded CPU determined by the daemon. To disable this daemon:
+          chkconfig --level 2345 irqbalance off
+
+      By default, some Linux distributions enable the kernel feature,
+      irqbalance, which performs the same function as the daemon. To disable
+      this feature, add the following line to your bootloader:
+          noirqbalance
+
+          Example using the Grub bootloader:
+              title Red Hat Enterprise Linux AS (2.4.21-27.ELsmp)
+              root (hd0,0)
+              kernel /vmlinuz-2.4.21-27.ELsmp ro root=/dev/hda3 noirqbalance
+              initrd /initrd-2.4.21-27.ELsmp.img
+
+  2. After running insmod, the driver is loaded and the incorrect network
+     interface is brought up without running ifup.
+
+      When using 2.4.x kernels, including RHEL kernels, the Linux kernel
+      invokes a script named "hotplug". This script is primarily used to
+      automatically bring up USB devices when they are plugged in, however,
+      the script also attempts to automatically bring up a network interface
+      after loading the kernel module. The hotplug script does this by scanning
+      the ifcfg-eth# config files in /etc/sysconfig/network-scripts, looking
+      for HWADDR=<mac_address>.
+
+      If the hotplug script does not find the HWADDRR within any of the
+      ifcfg-eth# files, it will bring up the device with the next available
+      interface name. If this interface is already configured for a different
+      network card, your new interface will have incorrect IP address and
+      network settings.
+
+      To solve this issue, you can add the HWADDR=<mac_address> key to the
+      interface config file of your network controller.
+
+      To disable this "hotplug" feature, you may add the driver (module name)
+      to the "blacklist" file located in /etc/hotplug. It has been noted that
+      this does not work for network devices because the net.agent script
+      does not use the blacklist file. Simply remove, or rename, the net.agent
+      script located in /etc/hotplug to disable this feature.
+
+  3. Transport Protocol (TP) hangs when running heavy multi-connection traffic
+     on an AMD Opteron system with HyperTransport PCI-X Tunnel chipset.
+
+      If your AMD Opteron system uses the AMD-8131 HyperTransport PCI-X Tunnel
+      chipset, you may experience the "133-Mhz Mode Split Completion Data
+      Corruption" bug identified by AMD while using a 133Mhz PCI-X card on the
+      bus PCI-X bus.
+
+      AMD states, "Under highly specific conditions, the AMD-8131 PCI-X Tunnel
+      can provide stale data via split completion cycles to a PCI-X card that
+      is operating at 133 Mhz", causing data corruption.
+
+      AMD's provides three workarounds for this problem, however, Chelsio
+      recommends the first option for best performance with this bug:
+
+        For 133Mhz secondary bus operation, limit the transaction length and
+        the number of outstanding transactions, via BIOS configuration
+        programming of the PCI-X card, to the following:
+
+           Data Length (bytes): 1k
+           Total allowed outstanding transactions: 2
+
+      Please refer to AMD 8131-HT/PCI-X Errata 26310 Rev 3.08 August 2004,
+      section 56, "133-MHz Mode Split Completion Data Corruption" for more
+      details with this bug and workarounds suggested by AMD.
+
+      It may be possible to work outside AMD's recommended PCI-X settings, try
+      increasing the Data Length to 2k bytes for increased performance. If you
+      have issues with these settings, please revert to the "safe" settings
+      and duplicate the problem before submitting a bug or asking for support.
+
+      NOTE: The default setting on most systems is 8 outstanding transactions
+            and 2k bytes data length.
+
+  4. On multiprocessor systems, it has been noted that an application which
+     is handling 10Gb networking can switch between CPUs causing degraded
+     and/or unstable performance.
+
+      If running on an SMP system and taking performance measurements, it
+      is suggested you either run the latest netperf-2.4.0+ or use a binding
+      tool such as Tim Hockin's procstate utilities (runon)
+      <http://www.hockin.org/~thockin/procstate/>.
+
+      Binding netserver and netperf (or other applications) to particular
+      CPUs will have a significant difference in performance measurements.
+      You may need to experiment which CPU to bind the application to in
+      order to achieve the best performance for your system.
+
+      If you are developing an application designed for 10Gb networking,
+      please keep in mind you may want to look at kernel functions
+      sched_setaffinity & sched_getaffinity to bind your application.
+
+      If you are just running user-space applications such as ftp, telnet,
+      etc., you may want to try the runon tool provided by Tim Hockin's
+      procstate utility. You could also try binding the interface to a
+      particular CPU: runon 0 ifup eth0
+
+
+SUPPORT
+=======
+
+ If you have problems with the software or hardware, please contact our
+ customer support team via email at support@chelsio.com or check our website
+ at http://www.chelsio.com
+
+===============================================================================
+
+ Chelsio Communications
+ 370 San Aleso Ave.
+ Suite 100
+ Sunnyvale, CA 94085
+ http://www.chelsio.com
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License, version 2, as
+published by the Free Software Foundation.
+
+You should have received a copy of the GNU General Public License along
+with this program; if not, write to the Free Software Foundation, Inc.,
+59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.
+
+THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED
+WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
+
+ Copyright (c) 2003-2005 Chelsio Communications. All rights reserved.
+
+===============================================================================
diff --git a/MAINTAINERS b/MAINTAINERS
index 564a03e61a0c..e8214fe53a5e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2092,6 +2092,12 @@ M:	support@simtec.co.uk
 W:	http://www.simtec.co.uk/products/EB2410ITX/
 S:	Supported
 
+SIS 190 ETHERNET DRIVER
+P:	Francois Romieu
+M:	romieu@fr.zoreil.com
+L:	netdev@vger.kernel.org
+S:	Maintained
+
 SIS 5513 IDE CONTROLLER DRIVER
 P:	Lionel Bouton
 M:	Lionel.Bouton@inet6.fr
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 79e8aa6f2b9e..e0239a10d325 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1923,6 +1923,17 @@ config R8169_VLAN
 	  
 	  If in doubt, say Y.
 
+config SIS190
+	tristate "SiS190 gigabit ethernet support"
+	depends on PCI
+	select CRC32
+	select MII
+	---help---
+	  Say Y here if you have a SiS 190 PCI Gigabit Ethernet adapter.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called sis190.  This is recommended.
+
 config SKGE
 	tristate "New SysKonnect GigaEthernet support (EXPERIMENTAL)"
 	depends on PCI && EXPERIMENTAL
@@ -2093,6 +2104,25 @@ endmenu
 menu "Ethernet (10000 Mbit)"
 	depends on !UML
 
+config CHELSIO_T1
+        tristate "Chelsio 10Gb Ethernet support"
+        depends on PCI
+        help
+          This driver supports Chelsio N110 and N210 models 10Gb Ethernet
+          cards. More information about adapter features and performance
+          tuning is in <file:Documentation/networking/cxgb.txt>.
+
+          For general information about Chelsio and our products, visit
+          our website at <http://www.chelsio.com>.
+
+          For customer support, please visit our customer support page at
+          <http://www.chelsio.com/support.htm>.
+
+          Please send feedback to <linux-bugs@chelsio.com>.
+
+          To compile this driver as a module, choose M here: the module
+          will be called cxgb.
+
 config IXGB
 	tristate "Intel(R) PRO/10GbE support"
 	depends on PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index a369ae284a9a..5baafcd55610 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -9,6 +9,7 @@ endif
 obj-$(CONFIG_E1000) += e1000/
 obj-$(CONFIG_IBM_EMAC) += ibm_emac/
 obj-$(CONFIG_IXGB) += ixgb/
+obj-$(CONFIG_CHELSIO_T1) += chelsio/
 obj-$(CONFIG_BONDING) += bonding/
 obj-$(CONFIG_GIANFAR) += gianfar_driver.o
 
@@ -42,6 +43,7 @@ obj-$(CONFIG_EEPRO100) += eepro100.o
 obj-$(CONFIG_E100) += e100.o
 obj-$(CONFIG_TLAN) += tlan.o
 obj-$(CONFIG_EPIC100) += epic100.o
+obj-$(CONFIG_SIS190) += sis190.o
 obj-$(CONFIG_SIS900) += sis900.o
 obj-$(CONFIG_YELLOWFIN) += yellowfin.o
 obj-$(CONFIG_ACENIC) += acenic.o
diff --git a/drivers/net/chelsio/Makefile b/drivers/net/chelsio/Makefile
new file mode 100644
index 000000000000..91e927827c43
--- /dev/null
+++ b/drivers/net/chelsio/Makefile
@@ -0,0 +1,11 @@
+#
+# Chelsio 10Gb NIC driver for Linux.
+#
+
+obj-$(CONFIG_CHELSIO_T1) += cxgb.o
+
+EXTRA_CFLAGS += -I$(TOPDIR)/drivers/net/chelsio $(DEBUG_FLAGS)
+
+
+cxgb-objs := cxgb2.o espi.o pm3393.o sge.o subr.o mv88x201x.o
+
diff --git a/drivers/net/chelsio/common.h b/drivers/net/chelsio/common.h
new file mode 100644
index 000000000000..f09348802b46
--- /dev/null
+++ b/drivers/net/chelsio/common.h
@@ -0,0 +1,314 @@
+/*****************************************************************************
+ *                                                                           *
+ * File: common.h                                                            *
+ * $Revision: 1.21 $                                                         *
+ * $Date: 2005/06/22 00:43:25 $                                              *
+ * Description:                                                              *
+ *  part of the Chelsio 10Gb Ethernet Driver.                                *
+ *                                                                           *
+ * This program is free software; you can redistribute it and/or modify      *
+ * it under the terms of the GNU General Public License, version 2, as       *
+ * published by the Free Software Foundation.                                *
+ *                                                                           *
+ * You should have received a copy of the GNU General Public License along   *
+ * with this program; if not, write to the Free Software Foundation, Inc.,   *
+ * 59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.                 *
+ *                                                                           *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED    *
+ * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF      *
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.                     *
+ *                                                                           *
+ * http://www.chelsio.com                                                    *
+ *                                                                           *
+ * Copyright (c) 2003 - 2005 Chelsio Communications, Inc.                    *
+ * All rights reserved.                                                      *
+ *                                                                           *
+ * Maintainers: maintainers@chelsio.com                                      *
+ *                                                                           *
+ * Authors: Dimitrios Michailidis   <dm@chelsio.com>                         *
+ *          Tina Yang               <tainay@chelsio.com>                     *
+ *          Felix Marti             <felix@chelsio.com>                      *
+ *          Scott Bardone           <sbardone@chelsio.com>                   *
+ *          Kurt Ottaway            <kottaway@chelsio.com>                   *
+ *          Frank DiMambro          <frank@chelsio.com>                      *
+ *                                                                           *
+ * History:                                                                  *
+ *                                                                           *
+ ****************************************************************************/
+
+#ifndef _CXGB_COMMON_H_
+#define _CXGB_COMMON_H_
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/crc32.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/pci_ids.h>
+
+#define DRV_DESCRIPTION "Chelsio 10Gb Ethernet Driver"
+#define DRV_NAME "cxgb"
+#define DRV_VERSION "2.1.1"
+#define PFX      DRV_NAME ": "
+
+#define CH_ERR(fmt, ...)   printk(KERN_ERR PFX fmt, ## __VA_ARGS__)
+#define CH_WARN(fmt, ...)  printk(KERN_WARNING PFX fmt, ## __VA_ARGS__)
+#define CH_ALERT(fmt, ...) printk(KERN_ALERT PFX fmt, ## __VA_ARGS__)
+
+#define CH_DEVICE(devid, ssid, idx) \
+	{ PCI_VENDOR_ID_CHELSIO, devid, PCI_ANY_ID, ssid, 0, 0, idx }
+
+#define SUPPORTED_PAUSE       (1 << 13)
+#define SUPPORTED_LOOPBACK    (1 << 15)
+
+#define ADVERTISED_PAUSE      (1 << 13)
+#define ADVERTISED_ASYM_PAUSE (1 << 14)
+
+typedef struct adapter adapter_t;
+
+void t1_elmer0_ext_intr(adapter_t *adapter);
+void t1_link_changed(adapter_t *adapter, int port_id, int link_status,
+			int speed, int duplex, int fc);
+
+struct t1_rx_mode {
+	struct net_device *dev;
+	u32 idx;
+	struct dev_mc_list *list;
+};
+
+#define t1_rx_mode_promisc(rm)	(rm->dev->flags & IFF_PROMISC)
+#define t1_rx_mode_allmulti(rm)	(rm->dev->flags & IFF_ALLMULTI)
+#define t1_rx_mode_mc_cnt(rm)	(rm->dev->mc_count)
+
+static inline u8 *t1_get_next_mcaddr(struct t1_rx_mode *rm)
+{
+	u8 *addr = 0;
+
+	if (rm->idx++ < rm->dev->mc_count) {
+		addr = rm->list->dmi_addr;
+		rm->list = rm->list->next;
+	}
+	return addr;
+}
+
+#define	MAX_NPORTS 4
+
+#define SPEED_INVALID 0xffff
+#define DUPLEX_INVALID 0xff
+
+enum {
+	CHBT_BOARD_N110,
+	CHBT_BOARD_N210
+};
+
+enum {
+	CHBT_TERM_T1,
+	CHBT_TERM_T2
+};
+
+enum {
+	CHBT_MAC_PM3393,
+};
+
+enum {
+	CHBT_PHY_88X2010,
+};
+
+enum {
+	PAUSE_RX      = 1 << 0,
+	PAUSE_TX      = 1 << 1,
+	PAUSE_AUTONEG = 1 << 2
+};
+
+/* Revisions of T1 chip */
+enum {
+	TERM_T1A   = 0,
+	TERM_T1B   = 1,
+	TERM_T2    = 3
+};
+
+struct sge_params {
+	unsigned int cmdQ_size[2];
+	unsigned int freelQ_size[2];
+	unsigned int large_buf_capacity;
+	unsigned int rx_coalesce_usecs;
+	unsigned int last_rx_coalesce_raw;
+	unsigned int default_rx_coalesce_usecs;
+	unsigned int sample_interval_usecs;
+	unsigned int coalesce_enable;
+	unsigned int polling;
+};
+
+struct chelsio_pci_params {
+	unsigned short speed;
+	unsigned char  width;
+	unsigned char  is_pcix;
+};
+
+struct adapter_params {
+	struct sge_params sge;
+	struct chelsio_pci_params pci;
+
+	const struct board_info *brd_info;
+
+	unsigned int   nports;          /* # of ethernet ports */
+	unsigned int   stats_update_period;
+	unsigned short chip_revision;
+	unsigned char  chip_version;
+};
+
+struct link_config {
+	unsigned int   supported;        /* link capabilities */
+	unsigned int   advertising;      /* advertised capabilities */
+	unsigned short requested_speed;  /* speed user has requested */
+	unsigned short speed;            /* actual link speed */
+	unsigned char  requested_duplex; /* duplex user has requested */
+	unsigned char  duplex;           /* actual link duplex */
+	unsigned char  requested_fc;     /* flow control user has requested */
+	unsigned char  fc;               /* actual link flow control */
+	unsigned char  autoneg;          /* autonegotiating? */
+};
+
+struct cmac;
+struct cphy;
+
+struct port_info {
+	struct net_device *dev;
+	struct cmac *mac;
+	struct cphy *phy;
+	struct link_config link_config;
+	struct net_device_stats netstats;
+};
+
+struct sge;
+struct peespi;
+
+struct adapter {
+	u8 *regs;
+	struct pci_dev *pdev;
+	unsigned long registered_device_map;
+	unsigned long open_device_map;
+	unsigned long flags;
+
+	const char *name;
+	int msg_enable;
+	u32 mmio_len;
+
+	struct work_struct ext_intr_handler_task;
+	struct adapter_params params;
+
+	struct vlan_group *vlan_grp;
+
+	/* Terminator modules. */
+	struct sge    *sge;
+	struct peespi *espi;
+
+	struct port_info port[MAX_NPORTS];
+	struct work_struct stats_update_task;
+	struct timer_list stats_update_timer;
+
+	struct semaphore mib_mutex;
+	spinlock_t tpi_lock;
+	spinlock_t work_lock;
+	/* guards async operations */
+	spinlock_t async_lock ____cacheline_aligned;
+	u32 slow_intr_mask;
+};
+
+enum {                                           /* adapter flags */
+	FULL_INIT_DONE        = 1 << 0,
+	TSO_CAPABLE           = 1 << 2,
+	TCP_CSUM_CAPABLE      = 1 << 3,
+	UDP_CSUM_CAPABLE      = 1 << 4,
+	VLAN_ACCEL_CAPABLE    = 1 << 5,
+	RX_CSUM_ENABLED       = 1 << 6,
+};
+
+struct mdio_ops;
+struct gmac;
+struct gphy;
+
+struct board_info {
+	unsigned char           board;
+	unsigned char           port_number;
+	unsigned long           caps;
+	unsigned char           chip_term;
+	unsigned char           chip_mac;
+	unsigned char           chip_phy;
+	unsigned int            clock_core;
+	unsigned int            clock_mc3;
+	unsigned int            clock_mc4;
+	unsigned int            espi_nports;
+	unsigned int            clock_cspi;
+	unsigned int            clock_elmer0;
+	unsigned char           mdio_mdien;
+	unsigned char           mdio_mdiinv;
+	unsigned char           mdio_mdc;
+	unsigned char           mdio_phybaseaddr;
+	struct gmac            *gmac;
+	struct gphy            *gphy;
+	struct mdio_ops	       *mdio_ops;
+	const char             *desc;
+};
+
+extern struct pci_device_id t1_pci_tbl[];
+
+static inline int adapter_matches_type(const adapter_t *adapter,
+				       int version, int revision)
+{
+	return adapter->params.chip_version == version &&
+	       adapter->params.chip_revision == revision;
+}
+
+#define t1_is_T1B(adap) adapter_matches_type(adap, CHBT_TERM_T1, TERM_T1B)
+#define is_T2(adap)     adapter_matches_type(adap, CHBT_TERM_T2, TERM_T2)
+
+/* Returns true if an adapter supports VLAN acceleration and TSO */
+static inline int vlan_tso_capable(const adapter_t *adapter)
+{
+	return !t1_is_T1B(adapter);
+}
+
+#define for_each_port(adapter, iter) \
+	for (iter = 0; iter < (adapter)->params.nports; ++iter)
+
+#define board_info(adapter) ((adapter)->params.brd_info)
+#define is_10G(adapter) (board_info(adapter)->caps & SUPPORTED_10000baseT_Full)
+
+static inline unsigned int core_ticks_per_usec(const adapter_t *adap)
+{
+	return board_info(adap)->clock_core / 1000000;
+}
+
+extern int t1_tpi_write(adapter_t *adapter, u32 addr, u32 value);
+extern int t1_tpi_read(adapter_t *adapter, u32 addr, u32 *value);
+
+extern void t1_interrupts_enable(adapter_t *adapter);
+extern void t1_interrupts_disable(adapter_t *adapter);
+extern void t1_interrupts_clear(adapter_t *adapter);
+extern int elmer0_ext_intr_handler(adapter_t *adapter);
+extern int t1_slow_intr_handler(adapter_t *adapter);
+
+extern int t1_link_start(struct cphy *phy, struct cmac *mac, struct link_config *lc);
+extern const struct board_info *t1_get_board_info(unsigned int board_id);
+extern const struct board_info *t1_get_board_info_from_ids(unsigned int devid,
+						    unsigned short ssid);
+extern int t1_seeprom_read(adapter_t *adapter, u32 addr, u32 *data);
+extern int t1_get_board_rev(adapter_t *adapter, const struct board_info *bi,
+		     struct adapter_params *p);
+extern int t1_init_hw_modules(adapter_t *adapter);
+extern int t1_init_sw_modules(adapter_t *adapter, const struct board_info *bi);
+extern void t1_free_sw_modules(adapter_t *adapter);
+extern void t1_fatal_err(adapter_t *adapter);
+
+extern void t1_tp_set_udp_checksum_offload(adapter_t *adapter, int enable);
+extern void t1_tp_set_tcp_checksum_offload(adapter_t *adapter, int enable);
+extern void t1_tp_set_ip_checksum_offload(adapter_t *adapter, int enable);
+
+#endif /* _CXGB_COMMON_H_ */
diff --git a/drivers/net/chelsio/cphy.h b/drivers/net/chelsio/cphy.h
new file mode 100644
index 000000000000..3412342f7345
--- /dev/null
+++ b/drivers/net/chelsio/cphy.h
@@ -0,0 +1,148 @@
+/*****************************************************************************
+ *                                                                           *
+ * File: cphy.h                                                              *
+ * $Revision: 1.7 $                                                          *
+ * $Date: 2005/06/21 18:29:47 $                                              *
+ * Description:                                                              *
+ *  part of the Chelsio 10Gb Ethernet Driver.                                *
+ *