Merge tag 'omap-for-v4.8/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup

Merge "drop last omap3 board files for v4.8" from Tony Lindgren:

Remove the last two legacy board-*.c files for omap3 for legacy
booting for v4.8 to allow making mach-omap2 device tree only for
v4.9.

We've had Nokia N900 and omap3 LDP board-*.c files remaining
while other omap3 devices have been device tree only for quite
a while now. Also N900 and LDP have had device tree based booting
working for years now, but few drivers for N900 were still only
working in legacy only mode until recently. With the remaining
issues out of the way, we discussed on the mailing lists that
we're finally OK to remove the remaining board-*.c files.

For the timing of this pull request, I wanted to wait until
v4.8-rc1 is out to make sure the legacy booting still works fine
after the merge window before doing it.

And for v4.8, let's not touch any other platform data in case we
still need to revert for some reason. This makes the revert just a
question of adding back the legacy board-*.c files.

Then if no issues, we can remove the unused remaining platform
data later on for v4.9.

* tag 'omap-for-v4.8/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Drop legacy board file for LDP
  ARM: OMAP2+: Drop legacy board file for n900

7 files changed, 0 insertions, 1977 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 5a0b380a8166..a9afeebd59f2 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -192,12 +192,6 @@ config MACH_OMAP2_TUSB6010
 	depends on ARCH_OMAP2 && SOC_OMAP2420
 	default y if MACH_NOKIA_N8X0
 
-config MACH_OMAP_LDP
-	bool "OMAP3 LDP board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_OMAP3517EVM
 	bool "OMAP3517/ AM3517 EVM board"
 	depends on ARCH_OMAP3
@@ -222,12 +216,6 @@ config MACH_NOKIA_N8X0
 	select MACH_NOKIA_N810
 	select MACH_NOKIA_N810_WIMAX
 
-config MACH_NOKIA_RX51
-	bool "Nokia N900 (RX-51) phone"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config OMAP3_SDRC_AC_TIMING
 	bool "Enable SDRC AC timing register changes"
 	depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index a7f2d051f524..5b37ec29996e 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -231,11 +231,7 @@ obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
-obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
 obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o
-obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o sdram-nokia.o
-obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o
-obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-video.o
 
 # Platform specific device init code
 
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
deleted file mode 100644
index 390795b334c3..000000000000
--- a/arch/arm/mach-omap2/board-ldp.c
+++ /dev/null
@@ -1,430 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-ldp.c
- *
- * Copyright (C) 2008 Texas Instruments Inc.
- * Nishant Kamat <nskamat@ti.com>
- *
- * Modified from mach-omap2/board-3430sdp.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/gpio_keys.h>
-#include <linux/workqueue.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/spi/spi.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/io.h>
-#include <linux/smsc911x.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include "gpmc-smsc911x.h"
-
-#include <linux/platform_data/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "board-flash.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "control.h"
-#include "common-board-devices.h"
-#include "display.h"
-
-#define LDP_SMSC911X_CS		1
-#define LDP_SMSC911X_GPIO	152
-#define DEBUG_BASE		0x08000000
-#define LDP_ETHR_START		DEBUG_BASE
-
-static uint32_t board_keymap[] = {
-	KEY(0, 0, KEY_1),
-	KEY(1, 0, KEY_2),
-	KEY(2, 0, KEY_3),
-	KEY(0, 1, KEY_4),
-	KEY(1, 1, KEY_5),
-	KEY(2, 1, KEY_6),
-	KEY(3, 1, KEY_F5),
-	KEY(0, 2, KEY_7),
-	KEY(1, 2, KEY_8),
-	KEY(2, 2, KEY_9),
-	KEY(3, 2, KEY_F6),
-	KEY(0, 3, KEY_F7),
-	KEY(1, 3, KEY_0),
-	KEY(2, 3, KEY_F8),
-	PERSISTENT_KEY(4, 5),
-	KEY(4, 4, KEY_VOLUMEUP),
-	KEY(5, 5, KEY_VOLUMEDOWN),
-	0
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap			= board_keymap,
-	.keymap_size		= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data ldp_kp_twl4030_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 6,
-	.cols		= 6,
-	.rep		= 1,
-};
-
-static struct gpio_keys_button ldp_gpio_keys_buttons[] = {
-	[0] = {
-		.code			= KEY_ENTER,
-		.gpio			= 101,
-		.desc			= "enter sw",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-	[1] = {
-		.code			= KEY_F1,
-		.gpio			= 102,
-		.desc			= "func 1",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-	[2] = {
-		.code			= KEY_F2,
-		.gpio			= 103,
-		.desc			= "func 2",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-	[3] = {
-		.code			= KEY_F3,
-		.gpio			= 104,
-		.desc			= "func 3",
-		.active_low		= 1,
-		.debounce_interval 	= 30,
-	},
-	[4] = {
-		.code			= KEY_F4,
-		.gpio			= 105,
-		.desc			= "func 4",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-	[5] = {
-		.code			= KEY_LEFT,
-		.gpio			= 106,
-		.desc			= "left sw",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-	[6] = {
-		.code			= KEY_RIGHT,
-		.gpio			= 107,
-		.desc			= "right sw",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-	[7] = {
-		.code			= KEY_UP,
-		.gpio			= 108,
-		.desc			= "up sw",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-	[8] = {
-		.code			= KEY_DOWN,
-		.gpio			= 109,
-		.desc			= "down sw",
-		.active_low		= 1,
-		.debounce_interval	= 30,
-	},
-};
-
-static struct gpio_keys_platform_data ldp_gpio_keys = {
-	.buttons		= ldp_gpio_keys_buttons,
-	.nbuttons		= ARRAY_SIZE(ldp_gpio_keys_buttons),
-	.rep			= 1,
-};
-
-static struct platform_device ldp_gpio_keys_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &ldp_gpio_keys,
-	},
-};
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
-	.cs             = LDP_SMSC911X_CS,
-	.gpio_irq       = LDP_SMSC911X_GPIO,
-	.gpio_reset     = -EINVAL,
-	.flags		= SMSC911X_USE_32BIT,
-};
-
-static inline void __init ldp_init_smsc911x(void)
-{
-	gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-/* LCD */
-
-#define LCD_PANEL_RESET_GPIO		55
-#define LCD_PANEL_QVGA_GPIO		56
-
-static const struct display_timing ldp_lcd_videomode = {
-	.pixelclock	= { 0, 5400000, 0 },
-
-	.hactive = { 0, 240, 0 },
-	.hfront_porch = { 0, 3, 0 },
-	.hback_porch = { 0, 39, 0 },
-	.hsync_len = { 0, 3, 0 },
-
-	.vactive = { 0, 320, 0 },
-	.vfront_porch = { 0, 2, 0 },
-	.vback_porch = { 0, 7, 0 },
-	.vsync_len = { 0, 1, 0 },
-
-	.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
-		DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data ldp_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 18,
-
-	.display_timing		= &ldp_lcd_videomode,
-
-	.enable_gpio		= -1,	/* filled in code */
-	.backlight_gpio		= -1,	/* filled in code */
-};
-
-static struct platform_device ldp_lcd_device = {
-	.name                   = "panel-dpi",
-	.id                     = 0,
-	.dev.platform_data      = &ldp_lcd_pdata,
-};
-
-static struct omap_dss_board_info ldp_dss_data = {
-	.default_display_name = "lcd",
-};
-
-static void __init ldp_display_init(void)
-{
-	int r;
-
-	static struct gpio gpios[] __initdata = {
-		{LCD_PANEL_RESET_GPIO, GPIOF_OUT_INIT_HIGH, "LCD RESET"},
-		{LCD_PANEL_QVGA_GPIO, GPIOF_OUT_INIT_HIGH, "LCD QVGA"},
-	};
-
-	r = gpio_request_array(gpios, ARRAY_SIZE(gpios));
-	if (r) {
-		pr_err("Cannot request LCD GPIOs, error %d\n", r);
-		return;
-	}
-
-	omap_display_init(&ldp_dss_data);
-}
-
-static int ldp_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio)
-{
-	int res;
-
-	/* LCD enable GPIO */
-	ldp_lcd_pdata.enable_gpio = gpio + 7;
-
-	/* Backlight enable GPIO */
-	ldp_lcd_pdata.backlight_gpio = gpio + 15;
-
-	res = platform_device_register(&ldp_lcd_device);
-	if (res)
-		pr_err("Unable to register LCD: %d\n", res);
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data ldp_gpio_data = {
-	.setup		= ldp_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply ldp_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data ldp_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(ldp_vmmc1_supply),
-	.consumer_supplies	= ldp_vmmc1_supply,
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply ldp_vaux1_supplies[] = {
-	REGULATOR_SUPPLY("vcc", "spi1.0"),
-};
-
-/* VAUX1 */
-static struct regulator_init_data ldp_vaux1 = {
-	.constraints = {
-		.min_uV			= 3000000,
-		.max_uV			= 3000000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies		= ARRAY_SIZE(ldp_vaux1_supplies),
-	.consumer_supplies		= ldp_vaux1_supplies,
-};
-
-static struct regulator_consumer_supply ldp_vpll2_supplies[] = {
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-static struct regulator_init_data ldp_vpll2 = {
-	.constraints = {
-		.name			= "VDVI",
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(ldp_vpll2_supplies),
-	.consumer_supplies	= ldp_vpll2_supplies,
-};
-
-static struct twl4030_platform_data ldp_twldata = {
-	/* platform_data for children goes here */
-	.vmmc1		= &ldp_vmmc1,
-	.vaux1		= &ldp_vaux1,
-	.vpll2		= &ldp_vpll2,
-	.gpio		= &ldp_gpio_data,
-	.keypad		= &ldp_kp_twl4030_data,
-};
-
-static int __init omap_i2c_init(void)
-{
-	omap3_pmic_get_config(&ldp_twldata,
-			  TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC, 0);
-	omap3_pmic_init("twl4030", &ldp_twldata);
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	omap_register_i2c_bus(3, 400, NULL, 0);
-	return 0;
-}
-
-static struct omap2_hsmmc_info mmc[] __initdata = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-	},
-	{}	/* Terminator */
-};
-
-static struct platform_device *ldp_devices[] __initdata = {
-	&ldp_gpio_keys_device,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct mtd_partition ldp_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader-NAND",
-		.offset		= 0,
-		.size		= 4 * (64 * 2048),	/* 512KB, 0x80000 */
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot-NAND",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 10 * (64 * 2048),	/* 1.25MB, 0x140000 */
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "Boot Env-NAND",
-		.offset		= MTDPART_OFS_APPEND,   /* Offset = 0x1c0000 */
-		.size		= 2 * (64 * 2048),	/* 256KB, 0x40000 */
-	},
-	{
-		.name		= "Kernel-NAND",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x0200000*/
-		.size		= 240 * (64 * 2048),	/* 30M, 0x1E00000 */
-	},
-	{
-		.name		= "File System - NAND",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x2000000 */
-		.size		= MTDPART_SIZ_FULL,	/* 96MB, 0x6000000 */
-	},
-
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap_ldp_init(void)
-{
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	ldp_init_smsc911x();
-	omap_i2c_init();
-	platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
-	omap_ads7846_init(1, 54, 310, NULL);
-	omap_serial_init();
-	omap_sdrc_init(NULL, NULL);
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-	board_nand_init(ldp_nand_partitions, ARRAY_SIZE(ldp_nand_partitions),
-			0, 0, nand_default_timings);
-
-	omap_hsmmc_init(mmc);
-	ldp_display_init();
-}
-
-MACHINE_START(OMAP_LDP, "OMAP LDP board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3430_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap_ldp_init,
-	.init_late	= omap3430_init_late,
-	.init_time	= omap_init_time,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
deleted file mode 100644
index a5ab712c1a59..000000000000
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ /dev/null
@@ -1,1312 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-rx51-peripherals.c
- *
- * Copyright (C) 2008-2009 Nokia
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/wl12xx.h>
-#include <linux/spi/tsc2005.h>
-#include <linux/i2c.h>
-#include <linux/i2c/twl.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/regulator/machine.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/gpio/machine.h>
-#include <linux/omap-gpmc.h>
-#include <linux/mmc/host.h>
-#include <linux/power/isp1704_charger.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/platform_data/mtd-onenand-omap2.h>
-
-#include <plat/dmtimer.h>
-
-#include <asm/system_info.h>
-
-#include "common.h"
-#include <linux/omap-dma.h>
-
-#include "board-rx51.h"
-
-#include <sound/tlv320aic3x.h>
-#include <sound/tpa6130a2-plat.h>
-#include <linux/platform_data/media/si4713.h>
-#include <linux/platform_data/leds-lp55xx.h>
-
-#include <linux/platform_data/tsl2563.h>
-#include <linux/lis3lv02d.h>
-
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/pwm_omap_dmtimer.h>
-#include <linux/platform_data/media/ir-rx51.h>
-
-#include "mux.h"
-#include "omap-pm.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-#include "soc.h"
-#include "omap-secure.h"
-
-#define SYSTEM_REV_B_USES_VAUX3	0x1699
-#define SYSTEM_REV_S_USES_VAUX3 0x8
-
-#define RX51_WL1251_POWER_GPIO		87
-#define RX51_WL1251_IRQ_GPIO		42
-#define RX51_FMTX_RESET_GPIO		163
-#define RX51_FMTX_IRQ			53
-#define RX51_LP5523_CHIP_EN_GPIO	41
-
-#define RX51_USB_TRANSCEIVER_RST_GPIO	67
-
-#define RX51_TSC2005_RESET_GPIO         104
-#define RX51_TSC2005_IRQ_GPIO           100
-
-#define LIS302_IRQ1_GPIO 181
-#define LIS302_IRQ2_GPIO 180  /* Not yet in use */
-
-/* List all SPI devices here. Note that the list/probe order seems to matter! */
-enum {
-	RX51_SPI_WL1251,
-	RX51_SPI_TSC2005,	/* Touch Controller */
-	RX51_SPI_MIPID,		/* LCD panel */
-};
-
-static struct wl1251_platform_data wl1251_pdata;
-static struct tsc2005_platform_data tsc2005_pdata;
-
-#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE)
-static int lis302_setup(void)
-{
-	int err;
-	int irq1 = LIS302_IRQ1_GPIO;
-	int irq2 = LIS302_IRQ2_GPIO;
-
-	/* gpio for interrupt pin 1 */
-	err = gpio_request(irq1, "lis3lv02dl_irq1");
-	if (err) {
-		printk(KERN_ERR "lis3lv02dl: gpio request failed\n");
-		goto out;
-	}
-
-	/* gpio for interrupt pin 2 */
-	err = gpio_request(irq2, "lis3lv02dl_irq2");
-	if (err) {
-		gpio_free(irq1);
-		printk(KERN_ERR "lis3lv02dl: gpio request failed\n");
-		goto out;
-	}
-
-	gpio_direction_input(irq1);
-	gpio_direction_input(irq2);
-
-out:
-	return err;
-}
-
-static int lis302_release(void)
-{
-	gpio_free(LIS302_IRQ1_GPIO);
-	gpio_free(LIS302_IRQ2_GPIO);
-
-	return 0;
-}
-
-static struct lis3lv02d_platform_data rx51_lis3lv02d_data = {
-	.click_flags    = LIS3_CLICK_SINGLE_X | LIS3_CLICK_SINGLE_Y |
-			  LIS3_CLICK_SINGLE_Z,
-	/* Limits are 0.5g * value */
-	.click_thresh_x = 8,
-	.click_thresh_y = 8,
-	.click_thresh_z = 10,
-	/* Click must be longer than time limit */
-	.click_time_limit = 9,
-	/* Kind of debounce filter */
-	.click_latency    = 50,
-
-	/* Limits for all axis. millig-value / 18 to get HW values */
-	.wakeup_flags = LIS3_WAKEUP_X_HI | LIS3_WAKEUP_Y_HI,
-	.wakeup_thresh = 800 / 18,
-	.wakeup_flags2 = LIS3_WAKEUP_Z_HI ,
-	.wakeup_thresh2 = 900 / 18,
-
-	.hipass_ctrl = LIS3_HIPASS1_DISABLE | LIS3_HIPASS2_DISABLE,
-
-	/* Interrupt line 2 for click detection, line 1 for thresholds */
-	.irq_cfg = LIS3_IRQ2_CLICK | LIS3_IRQ1_FF_WU_12,
-
-	.axis_x = LIS3_DEV_X,
-	.axis_y = LIS3_INV_DEV_Y,
-	.axis_z = LIS3_INV_DEV_Z,
-	.setup_resources = lis302_setup,
-	.release_resources = lis302_release,
-	.st_min_limits = {-32, 3, 3},
-	.st_max_limits = {-3, 32, 32},
-};
-#endif
-
-#if defined(CONFIG_SENSORS_TSL2563) || defined(CONFIG_SENSORS_TSL2563_MODULE)
-static struct tsl2563_platform_data rx51_tsl2563_platform_data = {
-	.cover_comp_gain = 16,
-};
-#endif
-
-#if defined(CONFIG_LEDS_LP5523) || defined(CONFIG_LEDS_LP5523_MODULE)
-static struct lp55xx_led_config rx51_lp5523_led_config[] = {
-	{
-		.name		= "lp5523:kb1",
-		.chan_nr	= 0,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:kb2",
-		.chan_nr	= 1,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:kb3",
-		.chan_nr	= 2,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:kb4",
-		.chan_nr	= 3,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:b",
-		.chan_nr	= 4,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:g",
-		.chan_nr	= 5,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:r",
-		.chan_nr	= 6,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:kb5",
-		.chan_nr	= 7,
-		.led_current	= 50,
-		.max_current	= 100,
-	}, {
-		.name		= "lp5523:kb6",
-		.chan_nr	= 8,
-		.led_current	= 50,
-		.max_current	= 100,
-	}
-};
-
-static struct lp55xx_platform_data rx51_lp5523_platform_data = {
-	.led_config		= rx51_lp5523_led_config,
-	.num_channels		= ARRAY_SIZE(rx51_lp5523_led_config),
-	.clock_mode		= LP55XX_CLOCK_AUTO,
-	.enable_gpio		= RX51_LP5523_CHIP_EN_GPIO,
-};
-#endif
-
-#define RX51_LCD_RESET_GPIO	90
-
-static struct panel_acx565akm_platform_data acx_pdata = {
-	.name		= "lcd",
-	.source		= "sdi.0",
-	.reset_gpio	= RX51_LCD_RESET_GPIO,
-	.datapairs	= 2,
-};
-
-static struct omap2_mcspi_device_config wl1251_mcspi_config = {
-	.turbo_mode	= 0,
-};
-
-static struct omap2_mcspi_device_config mipid_mcspi_config = {
-	.turbo_mode	= 0,
-};
-
-static struct omap2_mcspi_device_config tsc2005_mcspi_config = {
-	.turbo_mode	= 0,
-};
-
-static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = {
-	[RX51_SPI_WL1251] = {
-		.modalias		= "wl1251",
-		.bus_num		= 4,
-		.chip_select		= 0,
-		.max_speed_hz   	= 48000000,
-		.mode                   = SPI_MODE_3,
-		.controller_data	= &wl1251_mcspi_config,
-		.platform_data		= &wl1251_pdata,
-	},
-	[RX51_SPI_MIPID] = {
-		.modalias		= "acx565akm",
-		.bus_num		= 1,
-		.chip_select		= 2,
-		.max_speed_hz		= 6000000,
-		.controller_data	= &mipid_mcspi_config,
-		.platform_data		= &acx_pdata,
-	},
-	[RX51_SPI_TSC2005] = {
-		.modalias		= "tsc2005",
-		.bus_num		= 1,
-		.chip_select		= 0,
-		.max_speed_hz		= 6000000,
-		.controller_data	= &tsc2005_mcspi_config,
-		.platform_data		= &tsc2005_pdata,
-	},
-};
-
-static struct platform_device rx51_battery_device = {
-	.name	= "rx51-battery",
-	.id	= -1,
-};
-
-static void rx51_charger_set_power(bool on)
-{
-	gpio_set_value(RX51_USB_TRANSCEIVER_RST_GPIO, on);
-}
-
-static struct isp1704_charger_data rx51_charger_data = {
-	.set_power	= rx51_charger_set_power,
-};
-
-static struct platform_device rx51_charger_device = {
-	.name	= "isp1704_charger",
-	.dev	= {
-		.platform_data = &rx51_charger_data,
-	},
-};
-
-static void __init rx51_charger_init(void)
-{
-	WARN_ON(gpio_request_one(RX51_USB_TRANSCEIVER_RST_GPIO,
-		GPIOF_OUT_INIT_HIGH, "isp1704_reset"));
-
-	platform_device_register(&rx51_battery_device);
-	platform_device_register(&rx51_charger_device);
-}
-
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-
-#define RX51_GPIO_CAMERA_LENS_COVER	110
-#define RX51_GPIO_CAMERA_FOCUS		68
-#define RX51_GPIO_CAMERA_CAPTURE	69
-#define RX51_GPIO_KEYPAD_SLIDE		71
-#define RX51_GPIO_LOCK_BUTTON		113
-#define RX51_GPIO_PROXIMITY		89
-
-#define RX51_GPIO_DEBOUNCE_TIMEOUT	10
-
-static struct gpio_keys_button rx51_gpio_keys[] = {
-	{
-		.desc			= "Camera Lens Cover",
-		.type			= EV_SW,
-		.code			= SW_CAMERA_LENS_COVER,
-		.gpio			= RX51_GPIO_CAMERA_LENS_COVER,
-		.active_low		= 1,
-		.debounce_interval	= RX51_GPIO_DEBOUNCE_TIMEOUT,
-	}, {
-		.desc			= "Camera Focus",
-		.type			= EV_KEY,
-		.code			= KEY_CAMERA_FOCUS,
-		.gpio			= RX51_GPIO_CAMERA_FOCUS,
-		.active_low		= 1,
-		.debounce_interval	= RX51_GPIO_DEBOUNCE_TIMEOUT,
-	}, {
-		.desc			= "Camera Capture",
-		.type			= EV_KEY,
-		.code			= KEY_CAMERA,
-		.gpio			= RX51_GPIO_CAMERA_CAPTURE,
-		.active_low		= 1,
-		.debounce_interval	= RX51_GPIO_DEBOUNCE_TIMEOUT,
-	}, {
-		.desc			= "Lock Button",
-		.type			= EV_KEY,
-		.code			= KEY_SCREENLOCK,
-		.gpio			= RX51_GPIO_LOCK_BUTTON,
-		.active_low		= 1,
-		.debounce_interval	= RX51_GPIO_DEBOUNCE_TIMEOUT,
-	}, {
-		.desc			= "Keypad Slide",
-		.type			= EV_SW,
-		.code			= SW_KEYPAD_SLIDE,
-		.gpio			= RX51_GPIO_KEYPAD_SLIDE,
-		.active_low		= 1,
-		.debounce_interval	= RX51_GPIO_DEBOUNCE_TIMEOUT,
-	}, {
-		.desc			= "Proximity Sensor",
-		.type			= EV_SW,
-		.code			= SW_FRONT_PROXIMITY,
-		.gpio			= RX51_GPIO_PROXIMITY,
-		.active_low		= 0,
-		.debounce_interval	= RX51_GPIO_DEBOUNCE_TIMEOUT,
-	}
-};
-
-static struct gpio_keys_platform_data rx51_gpio_keys_data = {
-	.buttons	= rx51_gpio_keys,
-	.nbuttons	= ARRAY_SIZE(rx51_gpio_keys),
-};
-
-static struct platform_device rx51_gpio_keys_device = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &rx51_gpio_keys_data,
-	},
-};
-
-static void __init rx51_add_gpio_keys(void)
-{
-	platform_device_register(&rx51_gpio_keys_device);
-}
-#else
-static void __init rx51_add_gpio_keys(void)
-{
-}
-#endif /* CONFIG_KEYBOARD_GPIO || CONFIG_KEYBOARD_GPIO_MODULE */
-
-static uint32_t board_keymap[] = {
-	/*
-	 * Note that KEY(x, 8, KEY_XXX) entries represent "entrire row
-	 * connected to the ground" matrix state.
-	 */
-	KEY(0, 0, KEY_Q),
-	KEY(0, 1, KEY_O),
-	KEY(0, 2, KEY_P),
-	KEY(0, 3, KEY_COMMA),
-	KEY(0, 4, KEY_BACKSPACE),
-	KEY(0, 6, KEY_A),
-	KEY(0, 7, KEY_S),
-
-	KEY(1, 0, KEY_W),
-	KEY(1, 1, KEY_D),
-	KEY(1, 2, KEY_F),
-	KEY(1, 3, KEY_G),
-	KEY(1, 4, KEY_H),
-	KEY(1, 5, KEY_J),
-	KEY(1, 6, KEY_K),
-	KEY(1, 7, KEY_L),
-
-	KEY(2, 0, KEY_E),
-	KEY(2, 1, KEY_DOT),
-	KEY(2, 2, KEY_UP),
-	KEY(2, 3, KEY_ENTER),
-	KEY(2, 5, KEY_Z),
-	KEY(2, 6, KEY_X),
-	KEY(2, 7, KEY_C),
-	KEY(2, 8, KEY_F9),
-
-	KEY(3, 0, KEY_R),
-	KEY(3, 1, KEY_V),
-	KEY(3, 2, KEY_B),
-	KEY(3, 3, KEY_N),
-	KEY(3, 4, KEY_M),
-	KEY(3, 5, KEY_SPACE),
-	KEY(3, 6, KEY_SPACE),
-	KEY(3, 7, KEY_LEFT),
-
-	KEY(4, 0, KEY_T),
-	KEY(4, 1, KEY_DOWN),
-	KEY(4, 2, KEY_RIGHT),
-	KEY(4, 4, KEY_LEFTCTRL),
-	KEY(4, 5, KEY_RIGHTALT),
-	KEY(4, 6, KEY_LEFTSHIFT),
-	KEY(4, 8, KEY_F10),
-
-	KEY(5, 0, KEY_Y),
-	KEY(5, 8, KEY_F11),
-
-	KEY(6, 0, KEY_U),
-
-	KEY(7, 0, KEY_I),
-	KEY(7, 1, KEY_F7),
-	KEY(7, 2, KEY_F8),
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap			= board_keymap,
-	.keymap_size		= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data rx51_kp_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 8,
-	.cols		= 8,
-	.rep		= 1,
-};
-
-/* Enable input logic and pull all lines up when eMMC is on. */
-static struct omap_board_mux rx51_mmc2_on_mux[] = {
-	OMAP3_MUX(SDMMC2_CMD, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT0, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT1, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT2, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT3, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT4, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT5, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT6, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT7, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-
-/* Disable input logic and pull all lines down when eMMC is off. */
-static struct omap_board_mux rx51_mmc2_off_mux[] = {
-	OMAP3_MUX(SDMMC2_CMD, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT0, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT1, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT2, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT3, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT4, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT5, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT6, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	OMAP3_MUX(SDMMC2_DAT7, OMAP_PULL_ENA | OMAP_MUX_MODE0),
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-
-static struct omap_mux_partition *partition;
-
-/*
- * Current flows to eMMC when eMMC is off and the data lines are pulled up,
- * so pull them down. N.B. we pull 8 lines because we are using 8 lines.
- */
-static void rx51_mmc2_remux(struct device *dev, int power_on)
-{
-	if (power_on)
-		omap_mux_write_array(partition, rx51_mmc2_on_mux);
-	else
-		omap_mux_write_array(partition, rx51_mmc2_off_mux);
-}
-
-static struct omap2_hsmmc_info mmc[] __initdata = {
-	{
-		.name		= "external",
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.cover_only	= true,
-		.gpio_cd	= 160,
-		.gpio_wp	= -EINVAL,
-	},
-	{
-		.name		= "internal",
-		.mmc		= 2,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-						/* See also rx51_mmc2_remux */
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-		.nonremovable	= true,
-		.remux		= rx51_mmc2_remux,
-	},
-	{}	/* Terminator */
-};
-
-static struct regulator_consumer_supply rx51_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply rx51_vaux2_supply[] = {
-	REGULATOR_SUPPLY("vdds_csib", "omap3isp"),
-};
-
-static struct regulator_consumer_supply rx51_vaux3_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-static struct regulator_consumer_supply rx51_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1"),
-};
-
-static struct regulator_consumer_supply rx51_vmmc2_supplies[] = {
-	/* tlv320aic3x analog supplies */
-	REGULATOR_SUPPLY("AVDD", "2-0018"),
-	REGULATOR_SUPPLY("DRVDD", "2-0018"),
-	REGULATOR_SUPPLY("AVDD", "2-0019"),
-	REGULATOR_SUPPLY("DRVDD", "2-0019"),
-	/* tpa6130a2 */
-	REGULATOR_SUPPLY("Vdd", "2-0060"),
-	/* Keep vmmc as last item. It is not iterated for newer boards */
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-static struct regulator_consumer_supply rx51_vio_supplies[] = {
-	/* tlv320aic3x digital supplies */
-	REGULATOR_SUPPLY("IOVDD", "2-0018"),
-	REGULATOR_SUPPLY("DVDD", "2-0018"),
-	REGULATOR_SUPPLY("IOVDD", "2-0019"),
-	REGULATOR_SUPPLY("DVDD", "2-0019"),
-	/* Si4713 IO supply */
-	REGULATOR_SUPPLY("vio", "2-0063"),
-	/* lis3lv02d */
-	REGULATOR_SUPPLY("Vdd_IO", "3-001d"),
-};
-
-static struct regulator_consumer_supply rx51_vaux1_consumers[] = {
-	REGULATOR_SUPPLY("vdds_sdi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_sdi", "omapdss_sdi.0"),
-	/* Si4713 supply */
-	REGULATOR_SUPPLY("vdd", "2-0063"),
-	/* lis3lv02d */
-	REGULATOR_SUPPLY("Vdd", "3-001d"),
-};
-
-static struct regulator_init_data rx51_vaux1 = {
-	.constraints = {
-		.name			= "V28",
-		.min_uV			= 2800000,
-		.max_uV			= 2800000,
-		.always_on		= true, /* due battery cover sensor */
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(rx51_vaux1_consumers),
-	.consumer_supplies	= rx51_vaux1_consumers,
-};
-
-static struct regulator_init_data rx51_vaux2 = {
-	.constraints = {
-		.name			= "VCSI",
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(rx51_vaux2_supply),
-	.consumer_supplies	= rx51_vaux2_supply,
-};
-
-/* VAUX3 - adds more power to VIO_18 rail */
-static struct regulator_init_data rx51_vaux3_cam = {
-	.constraints = {
-		.name			= "VCAM_DIG_18",
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-};
-
-static struct regulator_init_data rx51_vaux3_mmc = {
-	.constraints = {
-		.name			= "VMMC2_30",
-		.min_uV			= 2800000,
-		.max_uV			= 3000000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(rx51_vaux3_supply),
-	.consumer_supplies	= rx51_vaux3_supply,
-};
-
-static struct regulator_init_data rx51_vaux4 = {
-	.constraints = {
-		.name			= "VCAM_ANA_28",
-		.min_uV			= 2800000,
-		.max_uV			= 2800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-};
-
-static struct regulator_init_data rx51_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| R