Merge tag 'hwmon-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "core:
   - Add support for enable attributes to hwmon core
   - Add intrusion templates

  pmbus:
   - Support for Infineon Multi-phase xdpe122 family controllers
   - Support for Intel IMVP9 and AMD 6.25mV modes
   - Support for vid mode detection per page bases
   - Detect if chip is write protected
   - Support for MAX20730, MAX20734, MAX20743, MAX20796, UCD90320,
     TPS53688
   - Various improvements to ibm-cffps driver

  k10temp:
   - Support for additional temperature sensors as well as voltage and
     current telemetry for Zen CPUs

  w83627ehf:
   - Remove support for NCT6775, NCT6776 (they have their own driver)

  New drivers:
   - ADM1177
   - MAX31730
   - Driver for disk and solid state drives with temperature sensors

  Other:
   - pwm-fan: stop fan on shutdown"

* tag 'hwmon-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (35 commits)
  hwmon: (k10temp) Display up to eight sets of CCD temperatures
  hwmon: (k10temp) Add debugfs support
  hwmon: (k10temp) Don't show temperature limits on Ryzen (Zen) CPUs
  hwmon: (k10temp) Show core and SoC current and voltages on Ryzen CPUs
  hwmon: (k10temp) Report temperatures per CPU die
  hmon: (k10temp) Convert to use devm_hwmon_device_register_with_info
  hwmon: (k10temp) Use bitops
  hwmon: (pwm-fan) stop fan on shutdown
  MAINTAINERS: add entry for ADM1177 driver
  dt-binding: hwmon: Add documentation for ADM1177
  hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
  docs: hwmon: Include 'xdpe12284.rst' into docs
  hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers
  hwmon: (pmbus/tps53679) Extend device list supported by driver
  hwmon: (pmbus/core) Add support for Intel IMVP9 and AMD 6.25mV modes
  hwmon: (pmbus/core) Add support for vid mode detection per page bases
  hwmon: (pmbus/ibm-cffps) Prevent writing on_off_config with bad data
  hwmon: (w83627ehf) Remove set but not used variable 'fan4min'
  hwmon: Driver for disk and solid state drives with temperature sensors
  hwmon: (pmbus/ibm-cffps) Fix the LED behavior when turned off
  ...

34 files changed, 3613 insertions, 1496 deletions

diff --git a/Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml b/Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml
new file mode 100644
index 000000000000..2a9822075b36
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/adi,adm1177.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor
+
+maintainers:
+  - Michael Hennerich <michael.hennerich@analog.com>
+  - Beniamin Bia <beniamin.bia@analog.com>
+
+description: |
+  Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor
+  https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
+
+properties:
+  compatible:
+    enum:
+      - adi,adm1177
+
+  reg:
+    maxItems: 1
+
+  avcc-supply:
+    description:
+      Phandle to the Avcc power supply
+
+  shunt-resistor-micro-ohms:
+    description:
+      The value of curent sense resistor in microohms. If not provided,
+      the current reading and overcurrent alert is disabled.
+
+  adi,shutdown-threshold-microamp:
+    description:
+      Specifies the current level at which an over current alert occurs.
+      If not provided, the overcurrent alert is configured to max ADC range
+      based on shunt-resistor-micro-ohms.
+
+  adi,vrange-high-enable:
+    description:
+      Specifies which internal voltage divider to be used. A 1 selects
+      a 7:2 voltage divider while a 0 selects a 14:1 voltage divider.
+    type: boolean
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pwmon@5a {
+                compatible = "adi,adm1177";
+                reg = <0x5a>;
+                shunt-resistor-micro-ohms = <50000>; /* 50 mOhm */
+                adi,shutdown-threshold-microamp = <1059000>; /* 1.059 A */
+                adi,vrange-high-enable;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/hwmon/pmbus/ti,ucd90320.yaml b/Documentation/devicetree/bindings/hwmon/pmbus/ti,ucd90320.yaml
new file mode 100644
index 000000000000..5d42e1304202
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/pmbus/ti,ucd90320.yaml
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/hwmon/pmbus/ti,ucd90320.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: UCD90320 power sequencer
+
+maintainers:
+  - Jim Wright <wrightj@linux.vnet.ibm.com>
+
+description: |
+  The UCD90320 is a 32-rail PMBus/I2C addressable power-supply sequencer and
+  monitor. The 24 integrated ADC channels (AMONx) monitor the power supply
+  voltage, current, and temperature. Of the 84 GPIO pins, 8 can be used as
+  digital monitors (DMONx), 32 to enable the power supply (ENx), 24 for
+  margining (MARx), 16 for logical GPO, and 32 GPIs for cascading, and system
+  function.
+
+  http://focus.ti.com/lit/ds/symlink/ucd90320.pdf
+
+properties:
+  compatible:
+    enum:
+      - ti,ucd90320
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ucd90320@11 {
+            compatible = "ti,ucd90320";
+            reg = <0x11>;
+        };
+    };
diff --git a/Documentation/hwmon/adm1177.rst b/Documentation/hwmon/adm1177.rst
new file mode 100644
index 000000000000..c81e0b4abd28
--- /dev/null
+++ b/Documentation/hwmon/adm1177.rst
@@ -0,0 +1,36 @@
+Kernel driver adm1177
+=====================
+
+Supported chips:
+  * Analog Devices ADM1177
+    Prefix: 'adm1177'
+    Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
+
+Author: Beniamin Bia <beniamin.bia@analog.com>
+
+
+Description
+-----------
+
+This driver supports hardware monitoring for Analog Devices ADM1177
+Hot-Swap Controller and Digital Power Monitors with Soft Start Pin.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Sysfs entries
+-------------
+
+The following attributes are supported. Current maxim attribute
+is read-write, all other attributes are read-only.
+
+in0_input		Measured voltage in microvolts.
+
+curr1_input		Measured current in microamperes.
+curr1_max_alarm		Overcurrent alarm in microamperes.
diff --git a/Documentation/hwmon/drivetemp.rst b/Documentation/hwmon/drivetemp.rst
new file mode 100644
index 000000000000..2d37d049247f
--- /dev/null
+++ b/Documentation/hwmon/drivetemp.rst
@@ -0,0 +1,52 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver drivetemp
+=======================
+
+
+References
+----------
+
+ANS T13/1699-D
+Information technology - AT Attachment 8 - ATA/ATAPI Command Set (ATA8-ACS)
+
+ANS Project T10/BSR INCITS 513
+Information technology - SCSI Primary Commands - 4 (SPC-4)
+
+ANS Project INCITS 557
+Information technology - SCSI / ATA Translation - 5 (SAT-5)
+
+
+Description
+-----------
+
+This driver supports reporting the temperature of disk and solid state
+drives with temperature sensors.
+
+If supported, it uses the ATA SCT Command Transport feature to read
+the current drive temperature and, if available, temperature limits
+as well as historic minimum and maximum temperatures. If SCT Command
+Transport is not supported, the driver uses SMART attributes to read
+the drive temperature.
+
+
+Sysfs entries
+-------------
+
+Only the temp1_input attribute is always available. Other attributes are
+available only if reported by the drive. All temperatures are reported in
+milli-degrees Celsius.
+
+=======================	=====================================================
+temp1_input		Current drive temperature
+temp1_lcrit		Minimum temperature limit. Operating the device below
+			this temperature may cause physical damage to the
+			device.
+temp1_min		Minimum recommended continuous operating limit
+temp1_max		Maximum recommended continuous operating temperature
+temp1_crit		Maximum temperature limit. Operating the device above
+			this temperature may cause physical damage to the
+			device.
+temp1_lowest		Minimum temperature seen this power cycle
+temp1_highest		Maximum temperature seen this power cycle
+=======================	=====================================================
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 43cc605741ea..b24adb67ddca 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -29,6 +29,7 @@ Hardware Monitoring Kernel Drivers
    adm1025
    adm1026
    adm1031
+   adm1177
    adm1275
    adm9240
    ads7828
@@ -47,6 +48,7 @@ Hardware Monitoring Kernel Drivers
    da9055
    dell-smm-hwmon
    dme1737
+   drivetemp
    ds1621
    ds620
    emc1403
@@ -106,8 +108,10 @@ Hardware Monitoring Kernel Drivers
    max1619
    max1668
    max197
+   max20730
    max20751
    max31722
+   max31730
    max31785
    max31790
    max34440
@@ -177,6 +181,7 @@ Hardware Monitoring Kernel Drivers
    wm831x
    wm8350
    xgene-hwmon
+   xdpe12284
    zl6100
 
 .. only::  subproject and html
diff --git a/Documentation/hwmon/max20730.rst b/Documentation/hwmon/max20730.rst
new file mode 100644
index 000000000000..cea7ae58c2f7
--- /dev/null
+++ b/Documentation/hwmon/max20730.rst
@@ -0,0 +1,74 @@
+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+Kernel driver max20730
+======================
+
+Supported chips:
+
+  * Maxim MAX20730
+
+    Prefix: 'max20730'
+
+    Addresses scanned: -
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20730.pdf
+
+  * Maxim MAX20734
+
+    Prefix: 'max20734'
+
+    Addresses scanned: -
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20734.pdf
+
+  * Maxim MAX20743
+
+    Prefix: 'max20743'
+
+    Addresses scanned: -
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20743.pdf
+
+Author: Guenter Roeck <linux@roeck-us.net>
+
+
+Description
+-----------
+
+This driver implements support for Maxim MAX20730, MAX20734, and MAX20743
+Integrated, Step-Down Switching Regulators with PMBus support.
+
+The driver is a client driver to the core PMBus driver.
+Please see Documentation/hwmon/pmbus.rst for details on PMBus client drivers.
+
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for
+details.
+
+
+Sysfs entries
+-------------
+
+=================== ===== =======================================================
+curr1_crit          RW/RO Critical output current. Please see datasheet for
+                          supported limits. Read-only if the chip is
+                          write protected; read-write otherwise.
+curr1_crit_alarm    RO    Output current critical alarm
+curr1_input         RO    Output current
+curr1_label         RO    'iout1'
+in1_alarm           RO    Input voltage alarm
+in1_input           RO    Input voltage
+in1_label           RO    'vin'
+in2_alarm           RO    Output voltage alarm
+in2_input           RO    Output voltage
+in2_label           RO    'vout1'
+temp1_crit          RW/RO Critical temeperature. Supported values are 130 or 150
+                          degrees C. Read-only if the chip is write protected;
+                          read-write otherwise.
+temp1_crit_alarm    RO    Temperature critical alarm
+temp1_input         RO    Chip temperature
+=================== ===== =======================================================
diff --git a/Documentation/hwmon/max31730.rst b/Documentation/hwmon/max31730.rst
new file mode 100644
index 000000000000..def0de19dbd2
--- /dev/null
+++ b/Documentation/hwmon/max31730.rst
@@ -0,0 +1,44 @@
+Kernel driver max31790
+======================
+
+Supported chips:
+
+  * Maxim MAX31730
+
+    Prefix: 'max31730'
+
+    Addresses scanned: 0x1c, 0x1d, 0x1e, 0x1f, 0x4c, 0x4d, 0x4e, 0x4f
+
+    Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX31730.pdf
+
+Author: Guenter Roeck <linux@roeck-us.net>
+
+
+Description
+-----------
+
+This driver implements support for Maxim MAX31730.
+
+The MAX31730 temperature sensor monitors its own temperature and the
+temperatures of three external diode-connected transistors. The operating
+supply voltage is from 3.0V to 3.6V. Resistance cancellation compensates
+for high series resistance in circuit-board traces and the external thermal
+diode, while beta compensation corrects for temperature-measurement
+errors due to low-beta sensing transistors.
+
+
+Sysfs entries
+-------------
+
+=================== == =======================================================
+temp[1-4]_enable    RW Temperature enable/disable
+                       Set to 0 to enable channel, 0 to disable
+temp[1-4]_input     RO Temperature input
+temp[2-4]_fault     RO Fault indicator for remote channels
+temp[1-4]_max       RW Maximum temperature
+temp[1-4]_max_alarm RW Maximum temperature alarm
+temp[1-4]_min       RW Minimum temperature. Common for all channels.
+                       Only temp1_min is writeable.
+temp[1-4]_min_alarm RO Minimum temperature alarm
+temp[2-4]_offset    RW Temperature offset for remote channels
+=================== == =======================================================
diff --git a/Documentation/hwmon/pmbus.rst b/Documentation/hwmon/pmbus.rst
index abfb9dd4857d..f787984e88a9 100644
--- a/Documentation/hwmon/pmbus.rst
+++ b/Documentation/hwmon/pmbus.rst
@@ -63,6 +63,16 @@ Supported chips:
 
 	http://www.ti.com/lit/gpn/tps544c25
 
+  * Maxim MAX20796
+
+    Prefix: 'max20796'
+
+    Addresses scanned: -
+
+    Datasheet:
+
+	Not published
+
   * Generic PMBus devices
 
     Prefix: 'pmbus'
diff --git a/Documentation/hwmon/ucd9000.rst b/Documentation/hwmon/ucd9000.rst
index 746f21fcb48c..704f0cbd95d3 100644
--- a/Documentation/hwmon/ucd9000.rst
+++ b/Documentation/hwmon/ucd9000.rst
@@ -3,9 +3,10 @@ Kernel driver ucd9000
 
 Supported chips:
 
-  * TI UCD90120, UCD90124, UCD90160, UCD9090, and UCD90910
+  * TI UCD90120, UCD90124, UCD90160, UCD90320, UCD9090, and UCD90910
 
-    Prefixes: 'ucd90120', 'ucd90124', 'ucd90160', 'ucd9090', 'ucd90910'
+    Prefixes: 'ucd90120', 'ucd90124', 'ucd90160', 'ucd90320', 'ucd9090',
+              'ucd90910'
 
     Addresses scanned: -
 
@@ -14,6 +15,7 @@ Supported chips:
 	- http://focus.ti.com/lit/ds/symlink/ucd90120.pdf
 	- http://focus.ti.com/lit/ds/symlink/ucd90124.pdf
 	- http://focus.ti.com/lit/ds/symlink/ucd90160.pdf
+	- http://focus.ti.com/lit/ds/symlink/ucd90320.pdf
 	- http://focus.ti.com/lit/ds/symlink/ucd9090.pdf
 	- http://focus.ti.com/lit/ds/symlink/ucd90910.pdf
 
@@ -45,6 +47,12 @@ power-on reset signals, external interrupts, cascading, or other system
 functions. Twelve of these pins offer PWM functionality. Using these pins, the
 UCD90160 offers support for margining, and general-purpose PWM functions.
 
+The UCD90320 is a 32-rail PMBus/I2C addressable power-supply sequencer and
+monitor. The 24 integrated ADC channels (AMONx) monitor the power supply
+voltage, current, and temperature. Of the 84 GPIO pins, 8 can be used as
+digital monitors (DMONx), 32 to enable the power supply (ENx), 24 for margining
+(MARx), 16 for logical GPO, and 32 GPIs for cascading, and system function.
+
 The UCD9090 is a 10-rail PMBus/I2C addressable power-supply sequencer and
 monitor. The device integrates a 12-bit ADC for monitoring up to 10 power-supply
 voltage inputs. Twenty-three GPIO pins can be used for power supply enables,
diff --git a/Documentation/hwmon/xdpe12284.rst b/Documentation/hwmon/xdpe12284.rst
new file mode 100644
index 000000000000..6b7ae98cc536
--- /dev/null
+++ b/Documentation/hwmon/xdpe12284.rst
@@ -0,0 +1,101 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver xdpe122
+=====================
+
+Supported chips:
+
+  * Infineon XDPE12254
+
+    Prefix: 'xdpe12254'
+
+  * Infineon XDPE12284
+
+    Prefix: 'xdpe12284'
+
+Authors:
+
+	Vadim Pasternak <vadimp@mellanox.com>
+
+Description
+-----------
+
+This driver implements support for Infineon Multi-phase XDPE122 family
+dual loop voltage regulators.
+The family includes XDPE12284 and XDPE12254 devices.
+The devices from this family complaint with:
+- Intel VR13 and VR13HC rev 1.3, IMVP8 rev 1.2 and IMPVP9 rev 1.3 DC-DC
+  converter specification.
+- Intel SVID rev 1.9. protocol.
+- PMBus rev 1.3 interface.
+
+Devices support linear format for reading input voltage, input and output current,
+input and output power and temperature.
+Device supports VID format for reading output voltage. The below modes are
+supported:
+- VR12.0 mode, 5-mV DAC - 0x01.
+- VR12.5 mode, 10-mV DAC - 0x02.
+- IMVP9 mode, 5-mV DAC - 0x03.
+- AMD mode 6.25mV - 0x10.
+
+Devices support two pages for telemetry.
+
+The driver provides for current: input, maximum and critical thresholds
+and maximum and critical alarms. Critical thresholds and critical alarm are
+supported only for current output.
+The driver exports the following attributes for via the sysfs files, where
+indexes 1, 2 are for "iin" and 3, 4 for "iout":
+
+**curr[3-4]_crit**
+
+**curr[3-4]_crit_alarm**
+
+**curr[1-4]_input**
+
+**curr[1-4]_label**
+
+**curr[1-4]_max**
+
+**curr[1-4]_max_alarm**
+
+The driver provides for voltage: input, critical and low critical thresholds
+and critical and low critical alarms.
+The driver exports the following attributes for via the sysfs files, where
+indexes 1, 2 are for "vin" and 3, 4 for "vout":
+
+**in[1-4]_crit**
+
+**in[1-4_crit_alarm**
+
+**in[1-4]_input**
+
+**in[1-4_label**
+
+**in[1-4]_lcrit**
+
+**in[1-41_lcrit_alarm**
+
+The driver provides for power: input and alarms. Power alarm is supported only
+for power input.
+The driver exports the following attributes for via the sysfs files, where
+indexes 1, 2 are for "pin" and 3, 4 for "pout":
+
+**power[1-2]_alarm**
+
+**power[1-4]_input**
+
+**power[1-4]_label**
+
+The driver provides for temperature: input, maximum and critical thresholds
+and maximum and critical alarms.
+The driver exports the following attributes for via the sysfs files:
+
+**temp[1-2]_crit**
+
+**temp[1-2]_crit_alarm**
+
+**temp[1-2]_input**
+
+**temp[1-2]_max**
+
+**temp[1-2]_max_alarm**
diff --git a/MAINTAINERS b/MAINTAINERS
index 56765f542244..ae8ff55f90df 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -977,6 +977,15 @@ W:	http://ez.analog.com/community/linux-device-drivers
 F:	drivers/iio/imu/adis16460.c
 F:	Documentation/devicetree/bindings/iio/imu/adi,adis16460.yaml
 
+ANALOG DEVICES INC ADM1177 DRIVER
+M:	Beniamin Bia <beniamin.bia@analog.com>
+M:	Michael Hennerich <Michael.Hennerich@analog.com>
+L:	linux-hwmon@vger.kernel.org
+W:	http://ez.analog.com/community/linux-device-drivers
+S:	Supported
+F:	drivers/hwmon/adm1177.c
+F:	Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml
+
 ANALOG DEVICES INC ADP5061 DRIVER
 M:	Stefan Popa <stefan.popa@analog.com>
 L:	linux-pm@vger.kernel.org
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 23dfe848979a..47ac20aee06f 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -164,6 +164,16 @@ config SENSORS_ADM1031
 	  This driver can also be built as a module. If so, the module
 	  will be called adm1031.
 
+config SENSORS_ADM1177
+	tristate "Analog Devices ADM1177 and compatibles"
+	depends on I2C
+	help
+	  If you say yes here you get support for Analog Devices ADM1177
+	  sensor chips.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called adm1177.
+
 config SENSORS_ADM9240
 	tristate "Analog Devices ADM9240 and compatibles"
 	depends on I2C
@@ -385,6 +395,16 @@ config SENSORS_ATXP1
 	  This driver can also be built as a module. If so, the module
 	  will be called atxp1.
 
+config SENSORS_DRIVETEMP
+	tristate "Hard disk drives with temperature sensors"
+	depends on SCSI && ATA
+	help
+	  If you say yes you get support for the temperature sensor on
+	  hard disk drives.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called satatemp.
+
 config SENSORS_DS620
 	tristate "Dallas Semiconductor DS620"
 	depends on I2C
@@ -889,7 +909,7 @@ config SENSORS_MAX197
 	  will be called max197.
 
 config SENSORS_MAX31722
-tristate "MAX31722 temperature sensor"
+	tristate "MAX31722 temperature sensor"
 	depends on SPI
 	help
 	  Support for the Maxim Integrated MAX31722/MAX31723 digital
@@ -898,6 +918,16 @@ tristate "MAX31722 temperature sensor"
 	  This driver can also be built as a module. If so, the module
 	  will be called max31722.
 
+config SENSORS_MAX31730
+	tristate "MAX31730 temperature sensor"
+	depends on I2C
+	help
+	  Support for the Maxim Integrated MAX31730 3-Channel Remote
+	  Temperature Sensor.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called max31730.
+
 config SENSORS_MAX6621
 	tristate "Maxim MAX6621 sensor chip"
 	depends on I2C
@@ -1905,7 +1935,7 @@ config SENSORS_W83627HF
 	  will be called w83627hf.
 
 config SENSORS_W83627EHF
-	tristate "Winbond W83627EHF/EHG/DHG/UHG, W83667HG, NCT6775F, NCT6776F"
+	tristate "Winbond W83627EHF/EHG/DHG/UHG, W83667HG"
 	depends on !PPC
 	select HWMON_VID
 	help
@@ -1918,8 +1948,7 @@ config SENSORS_W83627EHF
 	  the Core 2 Duo. And also the W83627UHG, which is a stripped down
 	  version of the W83627DHG (as far as hardware monitoring goes.)
 
-	  This driver also supports Nuvoton W83667HG, W83667HG-B, NCT6775F
-	  (also known as W83667HG-I), and NCT6776F.
+	  This driver also supports Nuvoton W83667HG and W83667HG-B.
 
 	  This driver can also be built as a module. If so, the module
 	  will be called w83627ehf.
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 6db5db9cdc29..613f50987965 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_SENSORS_ADM1025)	+= adm1025.o
 obj-$(CONFIG_SENSORS_ADM1026)	+= adm1026.o
 obj-$(CONFIG_SENSORS_ADM1029)	+= adm1029.o
 obj-$(CONFIG_SENSORS_ADM1031)	+= adm1031.o
+obj-$(CONFIG_SENSORS_ADM1177)	+= adm1177.o
 obj-$(CONFIG_SENSORS_ADM9240)	+= adm9240.o
 obj-$(CONFIG_SENSORS_ADS7828)	+= ads7828.o
 obj-$(CONFIG_SENSORS_ADS7871)	+= ads7871.o
@@ -56,6 +57,7 @@ obj-$(CONFIG_SENSORS_DA9052_ADC)+= da9052-hwmon.o
 obj-$(CONFIG_SENSORS_DA9055)+= da9055-hwmon.o
 obj-$(CONFIG_SENSORS_DELL_SMM)	+= dell-smm-hwmon.o
 obj-$(CONFIG_SENSORS_DME1737)	+= dme1737.o
+obj-$(CONFIG_SENSORS_DRIVETEMP)	+= drivetemp.o
 obj-$(CONFIG_SENSORS_DS620)	+= ds620.o
 obj-$(CONFIG_SENSORS_DS1621)	+= ds1621.o
 obj-$(CONFIG_SENSORS_EMC1403)	+= emc1403.o
@@ -123,6 +125,7 @@ obj-$(CONFIG_SENSORS_MAX1619)	+= max1619.o
 obj-$(CONFIG_SENSORS_MAX1668)	+= max1668.o
 obj-$(CONFIG_SENSORS_MAX197)	+= max197.o
 obj-$(CONFIG_SENSORS_MAX31722)	+= max31722.o
+obj-$(CONFIG_SENSORS_MAX31730)	+= max31730.o
 obj-$(CONFIG_SENSORS_MAX6621)	+= max6621.o
 obj-$(CONFIG_SENSORS_MAX6639)	+= max6639.o
 obj-$(CONFIG_SENSORS_MAX6642)	+= max6642.o
diff --git a/drivers/hwmon/adm1177.c b/drivers/hwmon/adm1177.c
new file mode 100644
index 000000000000..d314223a404a
--- /dev/null
+++ b/drivers/hwmon/adm1177.c
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ADM1177 Hot Swap Controller and Digital Power Monitor with Soft Start Pin
+ *
+ * Copyright 2015-2019 Analog Devices Inc.
+ */
+
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/hwmon.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+
+/*  Command Byte Operations */
+#define ADM1177_CMD_V_CONT	BIT(0)
+#define ADM1177_CMD_I_CONT	BIT(2)
+#define ADM1177_CMD_VRANGE	BIT(4)
+
+/* Extended Register */
+#define ADM1177_REG_ALERT_TH	2
+
+#define ADM1177_BITS		12
+
+/**
+ * struct adm1177_state - driver instance specific data
+ * @client		pointer to i2c client
+ * @reg			regulator info for the the power supply of the device
+ * @r_sense_uohm	current sense resistor value
+ * @alert_threshold_ua	current limit for shutdown
+ * @vrange_high		internal voltage divider
+ */
+struct adm1177_state {
+	struct i2c_client	*client;
+	struct regulator	*reg;
+	u32			r_sense_uohm;
+	u32			alert_threshold_ua;
+	bool			vrange_high;
+};
+
+static int adm1177_read_raw(struct adm1177_state *st, u8 num, u8 *data)
+{
+	return i2c_master_recv(st->client, data, num);
+}
+
+static int adm1177_write_cmd(struct adm1177_state *st, u8 cmd)
+{
+	return i2c_smbus_write_byte(st->client, cmd);
+}
+
+static int adm1177_write_alert_thr(struct adm1177_state *st,
+				   u32 alert_threshold_ua)
+{
+	u64 val;
+	int ret;
+
+	val = 0xFFULL * alert_threshold_ua * st->r_sense_uohm;
+	val = div_u64(val, 105840000U);
+	val = div_u64(val, 1000U);
+	if (val > 0xFF)
+		val = 0xFF;
+
+	ret = i2c_smbus_write_byte_data(st->client, ADM1177_REG_ALERT_TH,
+					val);
+	if (ret)
+		return ret;
+
+	st->alert_threshold_ua = alert_threshold_ua;
+	return 0;
+}
+
+static int adm1177_read(struct device *dev, enum hwmon_sensor_types type,
+			u32 attr, int channel, long *val)
+{
+	struct adm1177_state *st = dev_get_drvdata(dev);
+	u8 data[3];
+	long dummy;
+	int ret;
+
+	switch (type) {
+	case hwmon_curr:
+		switch (attr) {
+		case hwmon_curr_input:
+			ret = adm1177_read_raw(st, 3, data);
+			if (ret < 0)
+				return ret;
+			dummy = (data[1] << 4) | (data[2] & 0xF);
+			/*
+			 * convert to milliamperes
+			 * ((105.84mV / 4096) x raw) / senseResistor(ohm)
+			 */
+			*val = div_u64((105840000ull * dummy),
+				       4096 * st->r_sense_uohm);
+			return 0;
+		case hwmon_curr_max_alarm:
+			*val = st->alert_threshold_ua;
+			return 0;
+		default:
+			return -EOPNOTSUPP;
+		}
+	case hwmon_in:
+		ret = adm1177_read_raw(st, 3, data);
+		if (ret < 0)
+			return ret;
+		dummy = (data[0] << 4) | (data[2] >> 4);
+		/*
+		 * convert to millivolts based on resistor devision
+		 * (V_fullscale / 4096) * raw
+		 */
+		if (st->vrange_high)
+			dummy *= 26350;
+		else
+			dummy *= 6650;
+
+		*val = DIV_ROUND_CLOSEST(dummy, 4096);