5 files changed, 43 insertions, 13 deletions

diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index fc118f649887..cae61d1ebec5 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -524,6 +524,7 @@ static void __init serial8250_isa_init_ports(void)
 		 */
 		up->mcr_mask = ~ALPHA_KLUDGE_MCR;
 		up->mcr_force = ALPHA_KLUDGE_MCR;
+		serial8250_set_defaults(up);
 	}
 
 	/* chain base port ops to support Remote Supervisor Adapter */
@@ -547,7 +548,6 @@ static void __init serial8250_isa_init_ports(void)
 		port->membase  = old_serial_port[i].iomem_base;
 		port->iotype   = old_serial_port[i].io_type;
 		port->regshift = old_serial_port[i].iomem_reg_shift;
-		serial8250_set_defaults(up);
 
 		port->irqflags |= irqflag;
 		if (serial8250_isa_config != NULL)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index ddb6aeb76dc5..04b9af7ed941 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -326,7 +326,17 @@ static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p)
 	 * devices will export them as GPIOs, so we pre-configure them safely
 	 * as inputs.
 	 */
-	u8 dir = pcidev->vendor == PCI_VENDOR_ID_EXAR ? 0xff : 0x00;
+
+	u8 dir = 0x00;
+
+	if  ((pcidev->vendor == PCI_VENDOR_ID_EXAR) &&
+		(pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) {
+		// Configure GPIO as inputs for Commtech adapters
+		dir = 0xff;
+	} else {
+		// Configure GPIO as outputs for SeaLevel adapters
+		dir = 0x00;
+	}
 
 	writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
 	writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index f839380c2f4c..98b8a3e30733 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -306,8 +306,21 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
 	}
 #endif
 
+	/*
+	 * Store the requested baud rate before calling the generic 8250
+	 * set_termios method. Standard 8250 port expects bauds to be
+	 * no higher than (uartclk / 16) so the baud will be clamped if it
+	 * gets out of that bound. Mediatek 8250 port supports speed
+	 * higher than that, therefore we'll get original baud rate back
+	 * after calling the generic set_termios method and recalculate
+	 * the speed later in this method.
+	 */
+	baud = tty_termios_baud_rate(termios);
+
 	serial8250_do_set_termios(port, termios, old);
 
+	tty_termios_encode_baud_rate(termios, baud, baud);
+
 	/*
 	 * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS)
 	 *
@@ -339,6 +352,11 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
 	 */
 	spin_lock_irqsave(&port->lock, flags);
 
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
 	/* set DLAB we have cval saved in up->lcr from the call to the core */
 	serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
 	serial_dl_write(up, quot);
diff --git a/drivers/tty/serial/serial-tegra.c b/drivers/tty/serial/serial-tegra.c
index 8de8bac9c6c7..04d1b0807e66 100644
--- a/drivers/tty/serial/serial-tegra.c
+++ b/drivers/tty/serial/serial-tegra.c
@@ -635,7 +635,7 @@ static void tegra_uart_handle_tx_pio(struct tegra_uart_port *tup)
 }
 
 static void tegra_uart_handle_rx_pio(struct tegra_uart_port *tup,
-		struct tty_port *tty)
+		struct tty_port *port)
 {
 	do {
 		char flag = TTY_NORMAL;
@@ -653,16 +653,18 @@ static void tegra_uart_handle_rx_pio(struct tegra_uart_port *tup,
 		ch = (unsigned char) tegra_uart_read(tup, UART_RX);
 		tup->uport.icount.rx++;
 
-		if (!uart_handle_sysrq_char(&tup->uport, ch) && tty)
-			tty_insert_flip_char(tty, ch, flag);
+		if (uart_handle_sysrq_char(&tup->uport, ch))
+			continue;
 
 		if (tup->uport.ignore_status_mask & UART_LSR_DR)
 			continue;
+
+		tty_insert_flip_char(port, ch, flag);
 	} while (1);
 }
 
 static void tegra_uart_copy_rx_to_tty(struct tegra_uart_port *tup,
-				      struct tty_port *tty,
+				      struct tty_port *port,
 				      unsigned int count)
 {
 	int copied;
@@ -672,17 +674,13 @@ static void tegra_uart_copy_rx_to_tty(struct tegra_uart_port *tup,
 		return;
 
 	tup->uport.icount.rx += count;
-	if (!tty) {
-		dev_err(tup->uport.dev, "No tty port\n");
-		return;
-	}
 
 	if (tup->uport.ignore_status_mask & UART_LSR_DR)
 		return;
 
 	dma_sync_single_for_cpu(tup->uport.dev, tup->rx_dma_buf_phys,
 				count, DMA_FROM_DEVICE);
-	copied = tty_insert_flip_string(tty,
+	copied = tty_insert_flip_string(port,
 			((unsigned char *)(tup->rx_dma_buf_virt)), count);
 	if (copied != count) {
 		WARN_ON(1);
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 672cfa075e28..2833f1418d6d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -1580,8 +1580,10 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	 * If register_console() don't assign value, then console_port pointer
 	 * is cleanup.
 	 */
-	if (!console_port)
+	if (!console_port) {
+		cdns_uart_console.index = id;
 		console_port = port;
+	}
 #endif
 
 	rc = uart_add_one_port(&cdns_uart_uart_driver, port);
@@ -1594,8 +1596,10 @@ static int cdns_uart_probe(struct platform_device *pdev)
 #ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
 	/* This is not port which is used for console that's why clean it up */
 	if (console_port == port &&
-	    !(cdns_uart_uart_driver.cons->flags & CON_ENABLED))
+	    !(cdns_uart_uart_driver.cons->flags & CON_ENABLED)) {
 		console_port = NULL;
+		cdns_uart_console.index = -1;
+	}
 #endif
 
 	cdns_uart_data->cts_override = of_property_read_bool(pdev->dev.of_node,