1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
# netdata configuration for aggregating data from remote hosts
#
# API keys authorize a pair of sending-receiving netdata servers.
# Once their communication is authorized, they can exchange metrics for any
# number of hosts.
#
# You can generate API keys, with the linux command: uuidgen
#
# -----------------------------------------------------------------------------
# 1. SLAVE NETDATA - THE ONE THAT WILL BE SENDING METRICS
[stream]
enabled = no
# where to send metrics to?
# A space separated list of IP:PORT is accepted. The first available will
# get the metrics.
# IPv6 addresses should be [IP]:PORT
destination =
# The API_KEY to use (as the sender)
api key =
# other options (uncomment and set)
# timeout seconds = 60
# default port = 19999
# buffer size bytes = 1048576
# reconnect delay seconds = 5
# initial clock resync iterations = 60
# -----------------------------------------------------------------------------
# 2. MASTER NETDATA - THE ONE THAT WILL BE RECEIVING METRICS
#
# You can have one API key per slave, or the same API key for all slaves.
#
# All options below are used in this order:
#
# a) MACHINE_GUID (settings for each machine)
# b) API_KEY (settings for the API key)
# c) this netdata defaults (as in netdata.conf)
#
# You can combine the above (the more specific setting will be used).
# API key authentication
# If the key is not listed here, it will not be able to connect.
[API_KEY]
# Default settings for the API key
# You can disable the API key, by setting this to: no
# The default (for unknown API keys) is also: no
enabled = no
# The default history in entries, for all hosts using this API key.
# You can also set it per host below.
# If you don't set it here, the history size of the central netdata
# will be used
default history = 3600
# The default memory mode to be used for all hosts using this API key.
# You can also set it per host below.
# If you don't set it here, the memory mode of netdata.conf will be used.
# Valid modes:
# save save on exit, load on start
# map like swap (continuously syncing to disks)
# ram keep it in RAM, don't touch the disk
# none no database (passing through this netdata)
default memory mode = ram
# Shall we enable health monitoring for the hosts using this API key?
# 3 values:
# yes enable alarms
# no do not enable alarms
# auto enable alarms, only when the sending netdata is connected
# You can also set it per host, below.
# The default is the same as to netdata.conf
health enabled by default = auto
# postpone alarms for a short period after the sender is connected
default postpone alarms on connect seconds = 60
# need to route metrics differently? set these.
# the defaults are the ones at the [stream] section
#default proxy enabled = yes | no
#default proxy destination = IP:PORT IP:PORT ...
#default proxy api key = API_KEY
# -----------------------------------------------------------------------------
# Each netdata has a unique GUID - generated the first time netdata starts.
# You can find it at /var/lib/netdata/registry/netdata.public.unique.id
# The host sending data will have one. If it is static and you can find it,
# you can give settings for each specific host here.
[MACHINE_GUID]
# enable this host: yes | no
# THIS IS NOT A SECURITY MECHANISM - AN ATTACKER CAN SET ANY OTHER GUID.
# Use only the API key for security.
enabled = no
# The number of entries in the database
history = 3600
# The memory mode of the database: save | map | ram | none
memory mode = save
# Health / alarms control: yes | no | auto
health enabled = yes
# postpone alarms when the sender connects
postpone alarms on connect seconds = 60
# need to route metrics differently?
#proxy enabled = yes | no
#proxy destination = IP:PORT IP:PORT ...
#proxy api key = API_KEY
|
