From d5aa11bfe9cebb4a3912b11748fd84aa15454229 Mon Sep 17 00:00:00 2001 From: Milo Kim Date: Tue, 28 Feb 2017 15:45:15 +0900 Subject: mfd: Add TI LMU driver TI LMU (Lighting Management Unit) driver supports lighting devices below. LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697. LMU devices have common features. - I2C interface for accessing device registers - Hardware enable pin control - Backlight brightness control - Notifier for hardware fault monitoring - Regulators for LCD display bias It contains fault monitor, backlight, LED and regulator driver. LMU fault monitor ----------------- LM3633 and LM3697 provide hardware monitoring feature. It enables open or short circuit detection. After monitoring is done, each device should be re-initialized. Notifier is used for this case. Separate patch for 'ti-lmu-fault-monitor' will be sent later. Backlight --------- It's handled by TI LMU backlight consolidated driver and chip dependent data. Separate patchset will be sent later. LED indicator ------------- LM3633 has 6 indicator LEDs. Programmable dimming pattern is also supported. Separate patch for 'leds-lm3633' will be sent later. Regulator --------- LM3631 has 5 regulators for the display bias. LM3632 supports 3 regulators. One consolidated driver enables it. The lm363x regulator driver is already upstreamed. Signed-off-by: Milo Kim Tested-by: Tony Lindgren Signed-off-by: Lee Jones --- drivers/mfd/Kconfig | 12 +++ drivers/mfd/Makefile | 2 + drivers/mfd/ti-lmu.c | 259 +++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 273 insertions(+) create mode 100644 drivers/mfd/ti-lmu.c (limited to 'drivers/mfd') diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 8bbc91b5186e..add0c35c38c5 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -1181,6 +1181,18 @@ config MFD_LP8788 TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight driver and current sinks. +config MFD_TI_LMU + tristate "TI Lighting Management Unit driver" + depends on I2C + select MFD_CORE + select REGMAP_I2C + help + Say yes here to enable support for TI LMU chips. + + TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697. + It consists of backlight, LED and regulator driver. + It provides consistent device controls for lighting functions. + config MFD_OMAP_USB_HOST bool "TI OMAP USBHS core and TLL driver" depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3 diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index e314ba1058dc..294a0525aeb1 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -127,6 +127,8 @@ obj-$(CONFIG_MFD_AXP20X_RSB) += axp20x-rsb.o obj-$(CONFIG_MFD_LP3943) += lp3943.o obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o +obj-$(CONFIG_MFD_TI_LMU) += ti-lmu.o + da9055-objs := da9055-core.o da9055-i2c.o obj-$(CONFIG_MFD_DA9055) += da9055.o obj-$(CONFIG_MFD_DA9062) += da9062-core.o diff --git a/drivers/mfd/ti-lmu.c b/drivers/mfd/ti-lmu.c new file mode 100644 index 000000000000..cfb411cde51c --- /dev/null +++ b/drivers/mfd/ti-lmu.c @@ -0,0 +1,259 @@ +/* + * TI LMU (Lighting Management Unit) Core Driver + * + * Copyright 2017 Texas Instruments + * + * Author: Milo Kim + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +struct ti_lmu_data { + struct mfd_cell *cells; + int num_cells; + unsigned int max_register; +}; + +static int ti_lmu_enable_hw(struct ti_lmu *lmu, enum ti_lmu_id id) +{ + int ret; + + if (gpio_is_valid(lmu->en_gpio)) { + ret = devm_gpio_request_one(lmu->dev, lmu->en_gpio, + GPIOF_OUT_INIT_HIGH, "lmu_hwen"); + if (ret) { + dev_err(lmu->dev, "Can not request enable GPIO: %d\n", + ret); + return ret; + } + } + + /* Delay about 1ms after HW enable pin control */ + usleep_range(1000, 1500); + + /* LM3631 has additional power up sequence - enable LCD_EN bit. */ + if (id == LM3631) { + return regmap_update_bits(lmu->regmap, LM3631_REG_DEVCTRL, + LM3631_LCD_EN_MASK, + LM3631_LCD_EN_MASK); + } + + return 0; +} + +static void ti_lmu_disable_hw(struct ti_lmu *lmu) +{ + if (gpio_is_valid(lmu->en_gpio)) + gpio_set_value(lmu->en_gpio, 0); +} + +static struct mfd_cell lm3532_devices[] = { + { + .name = "ti-lmu-backlight", + .id = LM3532, + .of_compatible = "ti,lm3532-backlight", + }, +}; + +#define LM363X_REGULATOR(_id) \ +{ \ + .name = "lm363x-regulator", \ + .id = _id, \ + .of_compatible = "ti,lm363x-regulator", \ +} \ + +static struct mfd_cell lm3631_devices[] = { + LM363X_REGULATOR(LM3631_BOOST), + LM363X_REGULATOR(LM3631_LDO_CONT), + LM363X_REGULATOR(LM3631_LDO_OREF), + LM363X_REGULATOR(LM3631_LDO_POS), + LM363X_REGULATOR(LM3631_LDO_NEG), + { + .name = "ti-lmu-backlight", + .id = LM3631, + .of_compatible = "ti,lm3631-backlight", + }, +}; + +static struct mfd_cell lm3632_devices[] = { + LM363X_REGULATOR(LM3632_BOOST), + LM363X_REGULATOR(LM3632_LDO_POS), + LM363X_REGULATOR(LM3632_LDO_NEG), + { + .name = "ti-lmu-backlight", + .id = LM3632, + .of_compatible = "ti,lm3632-backlight", + }, +}; + +static struct mfd_cell lm3633_devices[] = { + { + .name = "ti-lmu-backlight", + .id = LM3633, + .of_compatible = "ti,lm3633-backlight", + }, + { + .name = "lm3633-leds", + .of_compatible = "ti,lm3633-leds", + }, + /* Monitoring driver for open/short circuit detection */ + { + .name = "ti-lmu-fault-monitor", + .id = LM3633, + .of_compatible = "ti,lm3633-fault-monitor", + }, +}; + +static struct mfd_cell lm3695_devices[] = { + { + .name = "ti-lmu-backlight", + .id = LM3695, + .of_compatible = "ti,lm3695-backlight", + }, +}; + +static struct mfd_cell lm3697_devices[] = { + { + .name = "ti-lmu-backlight", + .id = LM3697, + .of_compatible = "ti,lm3697-backlight", + }, + /* Monitoring driver for open/short circuit detection */ + { + .name = "ti-lmu-fault-monitor", + .id = LM3697, + .of_compatible = "ti,lm3697-fault-monitor", + }, +}; + +#define TI_LMU_DATA(chip, max_reg) \ +static const struct ti_lmu_data chip##_data = \ +{ \ + .cells = chip##_devices, \ + .num_cells = ARRAY_SIZE(chip##_devices),\ + .max_register = max_reg, \ +} \ + +TI_LMU_DATA(lm3532, LM3532_MAX_REG); +TI_LMU_DATA(lm3631, LM3631_MAX_REG); +TI_LMU_DATA(lm3632, LM3632_MAX_REG); +TI_LMU_DATA(lm3633, LM3633_MAX_REG); +TI_LMU_DATA(lm3695, LM3695_MAX_REG); +TI_LMU_DATA(lm3697, LM3697_MAX_REG); + +static const struct of_device_id ti_lmu_of_match[] = { + { .compatible = "ti,lm3532", .data = &lm3532_data }, + { .compatible = "ti,lm3631", .data = &lm3631_data }, + { .compatible = "ti,lm3632", .data = &lm3632_data }, + { .compatible = "ti,lm3633", .data = &lm3633_data }, + { .compatible = "ti,lm3695", .data = &lm3695_data }, + { .compatible = "ti,lm3697", .data = &lm3697_data }, + { } +}; +MODULE_DEVICE_TABLE(of, ti_lmu_of_match); + +static int ti_lmu_probe(struct i2c_client *cl, const struct i2c_device_id *id) +{ + struct device *dev = &cl->dev; + const struct of_device_id *match; + const struct ti_lmu_data *data; + struct regmap_config regmap_cfg; + struct ti_lmu *lmu; + int ret; + + match = of_match_device(ti_lmu_of_match, dev); + if (!match) + return -ENODEV; + /* + * Get device specific data from of_match table. + * This data is defined by using TI_LMU_DATA() macro. + */ + data = (struct ti_lmu_data *)match->data; + + lmu = devm_kzalloc(dev, sizeof(*lmu), GFP_KERNEL); + if (!lmu) + return -ENOMEM; + + lmu->dev = &cl->dev; + + /* Setup regmap */ + memset(®map_cfg, 0, sizeof(struct regmap_config)); + regmap_cfg.reg_bits = 8; + regmap_cfg.val_bits = 8; + regmap_cfg.name = id->name; + regmap_cfg.max_register = data->max_register; + + lmu->regmap = devm_regmap_init_i2c(cl, ®map_cfg); + if (IS_ERR(lmu->regmap)) + return PTR_ERR(lmu->regmap); + + /* HW enable pin control and additional power up sequence if required */ + lmu->en_gpio = of_get_named_gpio(dev->of_node, "enable-gpios", 0); + ret = ti_lmu_enable_hw(lmu, id->driver_data); + if (ret) + return ret; + + /* + * Fault circuit(open/short) can be detected by ti-lmu-fault-monitor. + * After fault detection is done, some devices should re-initialize + * configuration. The notifier enables such kind of handling. + */ + BLOCKING_INIT_NOTIFIER_HEAD(&lmu->notifier); + + i2c_set_clientdata(cl, lmu); + + return mfd_add_devices(lmu->dev, 0, data->cells, + data->num_cells, NULL, 0, NULL); +} + +static int ti_lmu_remove(struct i2c_client *cl) +{ + struct ti_lmu *lmu = i2c_get_clientdata(cl); + + ti_lmu_disable_hw(lmu); + mfd_remove_devices(lmu->dev); + return 0; +} + +static const struct i2c_device_id ti_lmu_ids[] = { + { "lm3532", LM3532 }, + { "lm3631", LM3631 }, + { "lm3632", LM3632 }, + { "lm3633", LM3633 }, + { "lm3695", LM3695 }, + { "lm3697", LM3697 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ti_lmu_ids); + +static struct i2c_driver ti_lmu_driver = { + .probe = ti_lmu_probe, + .remove = ti_lmu_remove, + .driver = { + .name = "ti-lmu", + .of_match_table = ti_lmu_of_match, + }, + .id_table = ti_lmu_ids, +}; + +module_i2c_driver(ti_lmu_driver); + +MODULE_DESCRIPTION("TI LMU MFD Core Driver"); +MODULE_AUTHOR("Milo Kim"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3