From e20119f7eaaaf6aad5b44f35155ce500429e17f6 Mon Sep 17 00:00:00 2001 From: Takeshi Kihara Date: Thu, 21 Feb 2019 13:59:38 +0100 Subject: arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb 12, 2019, the DMA channels for SCIF5 are corrected from 16..47 to 0..15 on R-Car E3. Signed-off-by: Takeshi Kihara Fixes: a5ebe5e49a862e21 ("arm64: dts: renesas: r8a77990: Add SCIF-{0,1,3,4,5} device nodes") Signed-off-by: Geert Uytterhoeven Reviewed-by: Fabrizio Castro Signed-off-by: Simon Horman --- arch/arm64/boot/dts/renesas/r8a77990.dtsi | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm64/boot/dts/renesas/r8a77990.dtsi b/arch/arm64/boot/dts/renesas/r8a77990.dtsi index 786178cf1ffd..36f409091cfc 100644 --- a/arch/arm64/boot/dts/renesas/r8a77990.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77990.dtsi @@ -2,7 +2,7 @@ /* * Device Tree Source for the R-Car E3 (R8A77990) SoC * - * Copyright (C) 2018 Renesas Electronics Corp. + * Copyright (C) 2018-2019 Renesas Electronics Corp. */ #include @@ -1042,9 +1042,8 @@ <&cpg CPG_CORE R8A77990_CLK_S3D1C>, <&scif_clk>; clock-names = "fck", "brg_int", "scif_clk"; - dmas = <&dmac1 0x5b>, <&dmac1 0x5a>, - <&dmac2 0x5b>, <&dmac2 0x5a>; - dma-names = "tx", "rx", "tx", "rx"; + dmas = <&dmac0 0x5b>, <&dmac0 0x5a>; + dma-names = "tx", "rx"; power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; resets = <&cpg 202>; status = "disabled"; -- cgit v1.2.3 From c21cd4ae82e169b394139243684aaacf31bfcdf8 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 21 Feb 2019 15:04:28 +0100 Subject: arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels Correct the DMA channels for SCIF5 from 16..47 to 0..15, as was done for R-Car E3. Signed-off-by: Takeshi Kihara Fixes: 2660a6af690ebbb4 ("arm64: dts: renesas: r8a774c0: Add SCIF and HSCIF nodes") Signed-off-by: Geert Uytterhoeven Reviewed-by: Fabrizio Castro Signed-off-by: Simon Horman --- arch/arm64/boot/dts/renesas/r8a774c0.dtsi | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi index f2e390f7f1d5..6590b63268b0 100644 --- a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi @@ -2,7 +2,7 @@ /* * Device Tree Source for the RZ/G2E (R8A774C0) SoC * - * Copyright (C) 2018 Renesas Electronics Corp. + * Copyright (C) 2018-2019 Renesas Electronics Corp. */ #include @@ -990,9 +990,8 @@ <&cpg CPG_CORE R8A774C0_CLK_S3D1C>, <&scif_clk>; clock-names = "fck", "brg_int", "scif_clk"; - dmas = <&dmac1 0x5b>, <&dmac1 0x5a>, - <&dmac2 0x5b>, <&dmac2 0x5a>; - dma-names = "tx", "rx", "tx", "rx"; + dmas = <&dmac0 0x5b>, <&dmac0 0x5a>; + dma-names = "tx", "rx"; power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; resets = <&cpg 202>; status = "disabled"; -- cgit v1.2.3 From 544e784188f1dd7c797c70b213385e67d92005b6 Mon Sep 17 00:00:00 2001 From: Helen Koike Date: Mon, 4 Mar 2019 18:48:37 -0300 Subject: ARM: dts: bcm283x: Fix hdmi hpd gpio pull Raspberry pi board model B revison 2 have the hot plug detector gpio active high (and not low as it was in the dts). Signed-off-by: Helen Koike Fixes: 49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree.") Reviewed-by: Eric Anholt Signed-off-by: Eric Anholt --- arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts index 5641d162dfdb..28e7513ce617 100644 --- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts +++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts @@ -93,7 +93,7 @@ }; &hdmi { - hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; }; &pwm { -- cgit v1.2.3 From 7a9b6be9fe58194d9a349159176e8cc0d8f10ef8 Mon Sep 17 00:00:00 2001 From: Eric Anholt Date: Fri, 8 Mar 2019 13:02:16 -0800 Subject: arm64: bcm2835: Add missing dependency on MFD_CORE. When adding the MFD dependency for power domains and WDT in bcm2835, I added it only on the arm32 side and missed it for arm64. Fixes: 5e6acc3e678e ("bcm2835-pm: Move bcm2835-watchdog's DT probe to an MFD.") Signed-off-by: Eric Anholt Reported-by: Stefan Wahren Acked-by: Stefan Wahren --- arch/arm64/Kconfig.platforms | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index 251ecf34cb02..50f9fb562059 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -27,6 +27,7 @@ config ARCH_BCM2835 bool "Broadcom BCM2835 family" select TIMER_OF select GPIOLIB + select MFD_CORE select PINCTRL select PINCTRL_BCM2835 select ARM_AMBA -- cgit v1.2.3 From 1a7ee0efb26d6e25433c6d4428028ac614f55ff1 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michal=20Vok=C3=A1=C4=8D?= Date: Fri, 1 Mar 2019 08:26:42 +0100 Subject: ARM: dts: imx6dl-yapp4: Use rgmii-id phy mode on the cpu port MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Use rgmii-id phy mode for the CPU port (MAC0) of the QCA8334 switch to add delays to both Tx and Rx clock. It worked with the rgmii mode before because the qca8k driver (incorrectly) enabled delays in that mode and rgmii-id was not implemented at all. Commit 5ecdd77c61c8 ("net: dsa: qca8k: disable delay for RGMII mode") removed the delays from the RGMII mode and hence broke the networking. To fix the problem, commit a968b5e9d587 ("net: dsa: qca8k: Enable delay for RGMII_ID mode") was introduced. Now the correct phy mode is available so use it. Signed-off-by: Michal Vokáč Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi index b715ab0fa1ff..091d829f6b05 100644 --- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi +++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi @@ -125,7 +125,7 @@ ethphy0: port@0 { reg = <0>; label = "cpu"; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; ethernet = <&fec>; fixed-link { -- cgit v1.2.3 From 0c17e83fe423467e3ccf0a02f99bd050a73bbeb4 Mon Sep 17 00:00:00 2001 From: Wen Yang Date: Fri, 1 Mar 2019 16:56:46 +0800 Subject: ARM: imx51: fix a leaked reference by adding missing of_node_put The call to of_get_next_child returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./arch/arm/mach-imx/mach-imx51.c:64:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 57, but without a corresponding object release within this function. Signed-off-by: Wen Yang Cc: Russell King Cc: Shawn Guo Cc: Sascha Hauer Cc: Pengutronix Kernel Team Cc: Fabio Estevam Cc: NXP Linux Team Cc: Lucas Stach Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo --- arch/arm/mach-imx/mach-imx51.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-imx/mach-imx51.c b/arch/arm/mach-imx/mach-imx51.c index c7169c2f94c4..08c7892866c2 100644 --- a/arch/arm/mach-imx/mach-imx51.c +++ b/arch/arm/mach-imx/mach-imx51.c @@ -59,6 +59,7 @@ static void __init imx51_m4if_setup(void) return; m4if_base = of_iomap(np, 0); + of_node_put(np); if (!m4if_base) { pr_err("Unable to map M4IF registers\n"); return; -- cgit v1.2.3 From 91740fc8242b4f260cfa4d4536d8551804777fae Mon Sep 17 00:00:00 2001 From: Kohji Okuno Date: Tue, 26 Feb 2019 11:34:13 +0900 Subject: ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time In the current cpuidle implementation for i.MX6q, the CPU that sets 'WAIT_UNCLOCKED' and the CPU that returns to 'WAIT_CLOCKED' are always the same. While the CPU that sets 'WAIT_UNCLOCKED' is in IDLE state of "WAIT", if the other CPU wakes up and enters IDLE state of "WFI" istead of "WAIT", this CPU can not wake up at expired time. Because, in the case of "WFI", the CPU must be waked up by the local timer interrupt. But, while 'WAIT_UNCLOCKED' is set, the local timer is stopped, when all CPUs execute "wfi" instruction. As a result, the local timer interrupt is not fired. In this situation, this CPU will wake up by IRQ different from local timer. (e.g. broacast timer) So, this fix changes CPU to return to 'WAIT_CLOCKED'. Signed-off-by: Kohji Okuno Fixes: e5f9dec8ff5f ("ARM: imx6q: support WAIT mode using cpuidle") Cc: Signed-off-by: Shawn Guo --- arch/arm/mach-imx/cpuidle-imx6q.c | 27 ++++++++++----------------- 1 file changed, 10 insertions(+), 17 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-imx/cpuidle-imx6q.c b/arch/arm/mach-imx/cpuidle-imx6q.c index bfeb25aaf9a2..326e870d7123 100644 --- a/arch/arm/mach-imx/cpuidle-imx6q.c +++ b/arch/arm/mach-imx/cpuidle-imx6q.c @@ -16,30 +16,23 @@ #include "cpuidle.h" #include "hardware.h" -static atomic_t master = ATOMIC_INIT(0); -static DEFINE_SPINLOCK(master_lock); +static int num_idle_cpus = 0; +static DEFINE_SPINLOCK(cpuidle_lock); static int imx6q_enter_wait(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index) { - if (atomic_inc_return(&master) == num_online_cpus()) { - /* - * With this lock, we prevent other cpu to exit and enter - * this function again and become the master. - */ - if (!spin_trylock(&master_lock)) - goto idle; + spin_lock(&cpuidle_lock); + if (++num_idle_cpus == num_online_cpus()) imx6_set_lpm(WAIT_UNCLOCKED); - cpu_do_idle(); - imx6_set_lpm(WAIT_CLOCKED); - spin_unlock(&master_lock); - goto done; - } + spin_unlock(&cpuidle_lock); -idle: cpu_do_idle(); -done: - atomic_dec(&master); + + spin_lock(&cpuidle_lock); + if (num_idle_cpus-- == num_online_cpus()) + imx6_set_lpm(WAIT_CLOCKED); + spin_unlock(&cpuidle_lock); return index; } -- cgit v1.2.3 From 032f85c9360fb1a08385c584c2c4ed114b33c260 Mon Sep 17 00:00:00 2001 From: Marco Felsch Date: Mon, 4 Mar 2019 11:49:40 +0100 Subject: ARM: dts: pfla02: increase phy reset duration Increase the reset duration to ensure correct phy functionality. The reset duration is taken from barebox commit 52fdd510de ("ARM: dts: pfla02: use long enough reset for ethernet phy"): Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a small percentage of modules have 'transmission timeouts' errors like barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0 warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3 eth0: 1000Mbps full duplex link detected eth0: transmission timeout T eth0: transmission timeout T eth0: transmission timeout T eth0: transmission timeout T eth0: transmission timeout Cc: Stefan Christ Cc: Christian Hemp Signed-off-by: Marco Felsch Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support") Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi index 433bf09a1954..027df06c5dc7 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi @@ -91,6 +91,7 @@ pinctrl-0 = <&pinctrl_enet>; phy-handle = <ðphy>; phy-mode = "rgmii"; + phy-reset-duration = <10>; /* in msecs */ phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; phy-supply = <&vdd_eth_io_reg>; status = "disabled"; -- cgit v1.2.3 From 3123be11683ed8c2f26f787df81966b538ca9f72 Mon Sep 17 00:00:00 2001 From: Nishad Kamdar Date: Mon, 11 Mar 2019 19:57:04 +0530 Subject: ARM: dts: imx6ull: Use the correct style for SPDX License Identifier This patch corrects the SPDX License Identifier style in imx6ull-pinfunc-snvs.h. Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46 and making some manual changes. Suggested-by: Joe Perches Signed-off-by: Nishad Kamdar Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ull-pinfunc-snvs.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h b/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h index f6fb6783c193..54cfe72295aa 100644 --- a/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h +++ b/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h @@ -1,4 +1,4 @@ -// SPDX-License-Identifier: GPL-2.0 +/* SPDX-License-Identifier: GPL-2.0 */ /* * Copyright (C) 2016 Freescale Semiconductor, Inc. * Copyright (C) 2017 NXP -- cgit v1.2.3 From 41b37f4c0fa67185691bcbd30201cad566f2f0d1 Mon Sep 17 00:00:00 2001 From: Masanari Iida Date: Tue, 19 Mar 2019 01:30:09 +0900 Subject: ARM: dts: imx6qdl: Fix typo in imx6qdl-icore-rqs.dtsi This patch fixes a spelling typo. Signed-off-by: Masanari Iida Fixes: cc42603de320 ("ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support") Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi index 1d1b4bd0670f..a4217f564a53 100644 --- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi @@ -264,7 +264,7 @@ pinctrl-2 = <&pinctrl_usdhc3_200mhz>; vmcc-supply = <®_sd3_vmmc>; cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; - bus-witdh = <4>; + bus-width = <4>; no-1-8-v; status = "okay"; }; @@ -275,7 +275,7 @@ pinctrl-1 = <&pinctrl_usdhc4_100mhz>; pinctrl-2 = <&pinctrl_usdhc4_200mhz>; vmcc-supply = <®_sd4_vmmc>; - bus-witdh = <8>; + bus-width = <8>; no-1-8-v; non-removable; status = "okay"; -- cgit v1.2.3 From 15b43e497ffd80ca44c00d781869a0e71f223ea5 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michal=20Vok=C3=A1=C4=8D?= Date: Wed, 20 Mar 2019 12:09:05 +0100 Subject: ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The switch is accessible through pseudo PHY which is located at 0x10. Signed-off-by: Michal Vokáč Fixes: 87489ec3a77f ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards") Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi index 091d829f6b05..e8d800fec637 100644 --- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi +++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi @@ -114,9 +114,9 @@ reg = <2>; }; - switch@0 { + switch@10 { compatible = "qca,qca8334"; - reg = <0>; + reg = <10>; switch_ports: ports { #address-cells = <1>; -- cgit v1.2.3 From 728e096dd70889c2e80dd4153feee91afb1daf72 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Thu, 10 Jan 2019 21:19:33 +0100 Subject: ARM: imx_v6_v7_defconfig: continue compiling the pwm driver MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit After the pwm-imx driver was split into two drivers and the Kconfig symbol changed accordingly, use the new name to continue being able to use the PWM hardware. Signed-off-by: Uwe Kleine-König Signed-off-by: Shawn Guo --- arch/arm/configs/imx_v6_v7_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig index 5586a5074a96..50fb01d70b10 100644 --- a/arch/arm/configs/imx_v6_v7_defconfig +++ b/arch/arm/configs/imx_v6_v7_defconfig @@ -398,7 +398,7 @@ CONFIG_MAG3110=y CONFIG_MPL3115=y CONFIG_PWM=y CONFIG_PWM_FSL_FTM=y -CONFIG_PWM_IMX=y +CONFIG_PWM_IMX27=y CONFIG_NVMEM_IMX_OCOTP=y CONFIG_NVMEM_VF610_OCOTP=y CONFIG_TEE=y -- cgit v1.2.3 From 507aaeeef80d70c46bdf07cda49234b36c2bbdcb Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Thu, 10 Jan 2019 21:19:34 +0100 Subject: ARM: imx_v4_v5_defconfig: enable PWM driver MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit While there is no mainline board that makes use of the PWM still enable the driver for it to increase compile test coverage. Signed-off-by: Uwe Kleine-König Signed-off-by: Shawn Guo --- arch/arm/configs/imx_v4_v5_defconfig | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig index 8661dd9b064a..b37f8e675e40 100644 --- a/arch/arm/configs/imx_v4_v5_defconfig +++ b/arch/arm/configs/imx_v4_v5_defconfig @@ -170,6 +170,9 @@ CONFIG_IMX_SDMA=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_IIO=y CONFIG_FSL_MX25_ADC=y +CONFIG_PWM=y +CONFIG_PWM_IMX1=y +CONFIG_PWM_IMX27=y CONFIG_EXT4_FS=y # CONFIG_DNOTIFY is not set CONFIG_VFAT_FS=y -- cgit v1.2.3 From 2dbed152e2d4c3fe2442284918d14797898b1e8a Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Wed, 20 Feb 2019 16:36:52 +0530 Subject: ARM: davinci: fix build failure with allnoconfig allnoconfig build with just ARCH_DAVINCI enabled fails because drivers/clk/davinci/* depends on REGMAP being enabled. Fix it by selecting REGMAP_MMIO when building in DaVinci support. Signed-off-by: Sekhar Nori Reviewed-by: David Lechner Signed-off-by: Arnd Bergmann --- arch/arm/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 054ead960f98..850b4805e2d1 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -596,6 +596,7 @@ config ARCH_DAVINCI select HAVE_IDE select PM_GENERIC_DOMAINS if PM select PM_GENERIC_DOMAINS_OF if PM && OF + select REGMAP_MMIO select RESET_CONTROLLER select SPARSE_IRQ select USE_OF -- cgit v1.2.3 From fa9463564e77067df81b0b8dec91adbbbc47bfb4 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 18 Mar 2019 16:31:22 +0100 Subject: ARM: dts: nomadik: Fix polarity of SPI CS The SPI DT bindings are for historical reasons a pitfall, the ability to flag a GPIO line as active high/low with the second cell flags was introduced later so the SPI subsystem will only accept the bool flag spi-cs-high to indicate that the line is active high. It worked by mistake, but the mistake was corrected in another commit. The comment in the DTS file was also misleading: this CS is indeed active high. Fixes: cffbb02dafa3 ("ARM: dts: nomadik: Augment NHK15 panel setting") Signed-off-by: Linus Walleij Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/ste-nomadik-nhk15.dts | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/ste-nomadik-nhk15.dts index 04066f9cb8a3..f2f6558a00f1 100644 --- a/arch/arm/boot/dts/ste-nomadik-nhk15.dts +++ b/arch/arm/boot/dts/ste-nomadik-nhk15.dts @@ -213,12 +213,13 @@ gpio-sck = <&gpio0 5 GPIO_ACTIVE_HIGH>; gpio-mosi = <&gpio0 4 GPIO_ACTIVE_HIGH>; /* - * It's not actually active high, but the frameworks assume - * the polarity of the passed-in GPIO is "normal" (active - * high) then actively drives the line low to select the - * chip. + * This chipselect is active high. Just setting the flags + * to GPIO_ACTIVE_HIGH is not enough for the SPI DT bindings, + * it will be ignored, only the special "spi-cs-high" flag + * really counts. */ cs-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + spi-cs-high; num-chipselects = <1>; /* -- cgit v1.2.3 From 93958742192e7956d05989836ada9071f9ffe42e Mon Sep 17 00:00:00 2001 From: Jonathan Hunter Date: Mon, 25 Mar 2019 12:28:07 +0100 Subject: arm64: tegra: Disable CQE Support for SDMMC4 on Tegra186 Enabling CQE support on Tegra186 Jetson TX2 has introduced a regression that is causing accesses to the file-system on the eMMC to fail. Errors such as the following have been observed ... mmc2: running CQE recovery mmc2: mmc_select_hs400 failed, error -110 print_req_error: I/O error, dev mmcblk2, sector 8 flags 80700 mmc2: cqhci: CQE failed to exit halt state For now disable CQE support for Tegra186 until this issue is resolved. Fixes: dfd3cb6feb73 arm64: tegra: Add CQE Support for SDMMC4 Signed-off-by: Jonathan Hunter Signed-off-by: Thierry Reding Signed-off-by: Arnd Bergmann --- arch/arm64/boot/dts/nvidia/tegra186.dtsi | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi index bb2045be8814..97aeb946ed5e 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi @@ -321,7 +321,6 @@ nvidia,default-trim = <0x9>; nvidia,dqs-trim = <63>; mmc-hs400-1_8v; - supports-cqe; status = "disabled"; }; -- cgit v1.2.3