summaryrefslogtreecommitdiffstats
path: root/sound
AgeCommit message (Collapse)Author
2011-01-10ALSA: virtuoso: handle DAC oversampling automaticallyClemens Ladisch
Remove the DAC Oversampling mixer control because this setting does not make much sense. For cards with the H6 daughterboard, 128x oversampling was disabled anyway because these high MCLK frequency would not be compatible with the connector cable. For cards without the H6 daughterboard, 128x gives a slightly higher output quality; there is no reason to reduce it to 64x except for saving power, but then these cards have not been designed to be power efficient anyway (the D2's blinkenlights cannot be disabled). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: use lower master clock with H6 daughterboardClemens Ladisch
Because of the unshielded connector cable, it is important to use as low a master clock frequency as possible with the H6. For double rate modes (64-96 kHz), the MCLK rate is unconditionally lowered from 512x to 256x because the higher rate would not improve anything. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: configure correct master clock frequency on the CS2000Clemens Ladisch
The clock output of the CS2000, which is used as master clock for the DACs, was using half the actual master clock frequency for some reason. Using the theoretically correct frequency seems also to work in practice. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: remove non-working controls on Essence ST DeluxeClemens Ladisch
On the Xonar Essence ST Deluxe, remove all mixer controls that would require I2C communication with the third DAC, which does not work because of an addressing conflict with the CS2000 chip. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: change PCM1796 format to I2SClemens Ladisch
Change the PCM format used for the PCM1796 from left-justified to I2S to ensure that the correct format is used even for the Essence ST Deluxe's center/LFE DAC, where I2C does not work because of an address conflict with the CS2000 chip. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: wait for PCM1796 clock to become stableClemens Ladisch
The PCM1796 needs the master clock for I2C communication to work, so add delays after clock changes to ensure that the clock is stable when we try to write the DACs' registers. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: do not use fast I2C speedClemens Ladisch
To make the I2C communication reliable when using the H6 daughterboard, reduce the I2C clock frequency. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: fix SPI clocks slower than 6.25 MHzClemens Ladisch
Fix wrong register bits for SPI clock cycle times longer than 160 ns, and adjust the polling loop timeout for these speeds. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: remove oxygen_model::private_data fieldClemens Ladisch
The number of DACs can now be deduced from the dac_channels_mixer field, so the private_data field is no longer needed. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: allow different number of PCM and mixer channelsClemens Ladisch
For cards like the Xonar HDAV1.3, differentiate between the number of PCM channels that can be played and the number of channels whose volume can be adjusted. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: Don't leak in sound/core/oss/pcm_oss.c::snd_pcm_hw_param_near()Jesper Juhl
snd_pcm_hw_param_near() will leak the memory allocated to 'save' if the call to snd_pcm_hw_param_max() returns less than zero. This patch makes sure we never leak. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-02ALSA: azt3328: improve snd_azf3328_codec_setdmaa()Andreas Mohr
- add some WARN_ONCE - add multi-I/O helper (and use helper struct) - fix off-by-1 DMA length bug - better variable naming Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-02ALSA: azt3328: use proper private_data hookup for codec identificationAndreas Mohr
- much improved implementation due to clean codec hierarchy - preparation for potential per-codec spinlock change NOTE: additionally removes a chip->pcm[codec_type] NULL ptr check (due to it requiring access to external chip struct), however I believe this to be ok since this condition should not occur and most drivers don't check against that either. Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-02ALSA: azt3328: use a helper variable to remove one indirection in hotpathAndreas Mohr
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-02ALSA: azt3328: cosmetics: use a helper variable for codec setupAndreas Mohr
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-02ALSA: azt3328: _setfmt() updateAndreas Mohr
- use a separate variable for the frequency part, don't always "or" it - use a "clever"(?) macro to shorten the code Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-02ALSA: azt3328: cosmetics, minor updatesAndreas Mohr
- correct samples to be POSIX shell compatible - add logging of jiffies value in _pointer() - several comments - cleanup Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-14ALSA: ml403-ac97cr: Use vsprintf extension %pR for struct resourceJoe Perches
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-13Merge branch 'topic/workq-update' into topic/miscTakashi Iwai
2010-12-13sound: don't use flush_scheduled_work()Tejun Heo
flush_scheduled_work() is deprecated and scheduled to be removed. * cancel[_delayed]_work() + flush_scheduled_work() -> cancel[_delayed]_work_sync(). * wm8350, wm8753 and soc-core use custom code to cancel a delayed work, execute it immediately if it was pending and wait for its completion. This is equivalent to flush_delayed_work_sync(). Use it instead. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-10ALSA: aoa: Remove wrong i2c_set_clientdata in onyx_i2c_remove()Axel Lin
It does not make sense to set clientdata to onyx in onyx_i2c_remove() as we are going to kfree onyx. What we really want here is i2c_set_clientdata(client, NULL); Since the i2c core will take care of it now, so this patch just removes it. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-09ALSA: ice1712 - working M-Audio Delta 66E supportBrian Bloniarz
Rev. E of the M-Audio Delta 66 is partially supported (commit ef2cd2ccad66b4aba518eca7514eface267ee0f3), but the layout of the GPIO pins was still unclear. This patch adds the GPIO definitions so that communication to the CS8247 & 2x AK4524 works correctly. ALSA bug#3327 has more details; users cap & jhunt report there that the GPIO wiring is similar to the Digigram VX442 (chip select: pin 4 = CS8427, pin 5 = AK4524 #0, pin 6 = AK4524 #1). There has been a lot of conflicting information in the bug, but given these definitions, my Delta 66E works; I tested analog in&out at 44.1kHz & 96kHz, analog gain settings, S/PDIF clock sync, and S/PDIF in&out at 44.1kHz. Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06sound: Fixed line limit issue in sound/ac97_bus.cJeffrin Jose
This is a patch to the sound/ac97_bus.c file that fixes up a 80 character line limit issue found by the checkpatch.pl tool. Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: oxygen: update hardware commentsClemens Ladisch
Reformat and update the comments that describe the hardware connections on the various models. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: oxygen: show correct package IDClemens Ladisch
Instead of the hardcoded "CMI8788", show the actual chip name. Note: This is neither what the chip is (it's always the same), nor what the chip is actually called. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: oxygen: allow to dump codec registersClemens Ladisch
To help with debugging, add the registers of the model-specific codecs to the controller and AC97 register dump in the proc file. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: virtuoso: fix front panel routing for D1/DX/ST(X)Clemens Ladisch
The "Front Panel" switch on the Xonar D1/DX actually switches only the output direction, so mark it appropriately. The front panel microphone is controlled by the FMIC2MIC bit of the CM9780. It was unconditionally enabled on the D1/DX and never set on the ST(X); add a control for it. Selecting the front panel microphone as source does not actually disable the microphone jack, but this is bug-compatible with the Windows driver, and users rely on it. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: virtuoso: add HDMI enable switch for HDAV1.3Clemens Ladisch
The GPIO bit that enables analog output on the Xonar HDAV1.3 also disables the HDMI audio output, so we better add a switch for it. Hopefully, this is sufficient to make the HDMI output work. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: virtuoso: initialize unknown GPIO bitsClemens Ladisch
Initialize the configuration of some unknown GPIO output bits (that might not be used at all) to be the same as in the Windows driver, just to be sure. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-03Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ASoC: omap: N810: Don't select CONFIG_OMAP_MUX but make it as dependency ALSA: hda: Use "alienware" model quirk for another SSID ASoC: WM8731: Fix incorrect mask for bypass path disable s6105-ipcam: fix compilation s6000-pcm: fix compilation s6000-i2s: fix compilation ASoC: Fix missing spin_unlock_irqrestore ALSA: Fix SNDCTL_DSP_RESET ioctl for OSS emulation ASoC: Add missing dev_set_drvdata in p1022_ds_probe ASoC: Add missing dev_set_drvdata in mpc8610_hpcd_probe ASoC: Remove unneeded !! operations while checking return value of nuc900_checkready ASoC: Fix compile error for nuc900-pcm.c ASoC: Fix prototype for nuc900_ac97_probe and nuc900_ac97_remove ASoC: Fix compile error for nuc900-ac97.c ALSA: hda: Use BIOS auto-parsing instead of existing model quirk for MEDION MD2
2010-12-02Merge branch 'fix/asoc' into for-linusTakashi Iwai
2010-12-02Merge branch 'for-2.6.37' of ↵Takashi Iwai
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into fix/asoc
2010-12-02Merge branch 'fix/hda' into for-linusTakashi Iwai
2010-12-02ASoC: omap: N810: Don't select CONFIG_OMAP_MUX but make it as dependencyJarkko Nikula
Not all omap boards use kernel based pin multiplexing so CONFIG_SND_OMAP_SOC_N810 should not select it by default as it can make harm to other boards in multi-board kernels. Therefore put CONFIG_OMAP_MUX as a dependency to N810 ASoC machine driver. Thanks to Tony Lindgren <tony@atomide.com> for noticing. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-02ALSA: hda: Use "alienware" model quirk for another SSIDDaniel T Chen
BugLink: https://launchpad.net/bugs/683695 The original reporter states that headphone jacks do not appear to work. Upon inspecting his codec dump, and upon further testing, it is confirmed that the "alienware" model quirk is correct. Reported-and-tested-by: Cody Thierauf Cc: <stable@kernel.org> [2.6.32+] Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-01ASoC: WM8731: Fix incorrect mask for bypass path disableDimitris Papastamos
According to the datasheet the bypass path enable/disable is bit 3 therefore we need 0x8 and not 0x4. Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-12-01ALSA: hdsp - Add support for RPM io boxFlorian Faber
Add support for the RME HDSP RPM IO box. Changes have been made in the identification of the IO box and the neccessary controls have been added. Signed-off-by: Florian Faber <faberman@linuxproaudio.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-30s6105-ipcam: fix compilationDaniel Glöckner
When the s6105-ipcam ASoC driver had been converted to the multi-component API, a single reference to a former structure element remained, blocking successful compilation. Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-30s6000-pcm: fix compilationDaniel Glöckner
s6000_soc_platform has lost its forward declaration and there no longer is a name element in it, so use a string constant when calling request_irq. Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-30s6000-i2s: fix compilationDaniel Glöckner
A semicolon was missing. Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-30ASoC: Fix missing spin_unlock_irqrestoreAxel Lin
In nuc900_dma_hw_params(), if snd_pcm_lib_malloc_pages failed it returns without calling spin_unlock_irqrestore(). Since snd_pcm_lib_malloc_pages() does not touch struct nuc900_audio, we don't need to hold the lock while calling snd_pcm_lib_malloc_pages(). Fix it by moving spin_lock_irqsave() down to after snd_pcm_lib_malloc_pages(). In nuc900_dma_prepare(), spin_unlock_irqrestore() is missing in the error path. Fix it by removing the return in default case. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wan ZongShun <mcuos.com@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-30ALSA: Fix SNDCTL_DSP_RESET ioctl for OSS emulationTakashi Iwai
In OSS emulation, SNDCTL_DSP_RESET ioctl needs the reset of the internal buffer state in addition to drop of the running streams. Otherwise the succeeding access becomes inconsistent. Tested-by: Amit Nagal <helloin.amit@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-29ASoC: Add missing dev_set_drvdata in p1022_ds_probeAxel Lin
Otherwise, calling dev_get_drvdata in p1022_ds_remove returns NULL. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Timur Tabi <timur@freescale.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-29ASoC: Add missing dev_set_drvdata in mpc8610_hpcd_probeAxel Lin
Otherwise, calling dev_get_drvdata in mpc8610_hpcd_remove returns NULL. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Timur Tabi <timur@freescale.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-29ASoC: Remove unneeded !! operations while checking return value of ↵Axel Lin
nuc900_checkready I think this unneededd !! operations just reduce the readability. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-29ASoC: Fix compile error for nuc900-pcm.cAxel Lin
This patch fixes below error: CC sound/soc/nuc900/nuc900-pcm.o sound/soc/nuc900/nuc900-pcm.c: In function 'nuc900_dma_open': sound/soc/nuc900/nuc900-pcm.c:267: error: 'nuc900_ac97_data' undeclared (first use in this function) sound/soc/nuc900/nuc900-pcm.c:267: error: (Each undeclared identifier is reported only once sound/soc/nuc900/nuc900-pcm.c:267: error: for each function it appears in.) sound/soc/nuc900/nuc900-pcm.c: At top level: sound/soc/nuc900/nuc900-pcm.c:337: error: expected ',' or ';' before 'static' sound/soc/nuc900/nuc900-pcm.c:354: error: 'nuc900_soc_platform_probe' undeclared here (not in a function) make[3]: *** [sound/soc/nuc900/nuc900-pcm.o] Error 1 make[2]: *** [sound/soc/nuc900] Error 2 make[1]: *** [sound/soc] Error 2 make: *** [sound] Error 2 Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-29ASoC: Fix prototype for nuc900_ac97_probe and nuc900_ac97_removeAxel Lin
This patch fixes below compile warning: CC sound/soc/nuc900/nuc900-ac97.o sound/soc/nuc900/nuc900-ac97.c:300: warning: initialization from incompatible pointer type sound/soc/nuc900/nuc900-ac97.c:301: warning: initialization from incompatible pointer type Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-29ASoC: Fix compile error for nuc900-ac97.cAxel Lin
Fix below compile error by add a missing ';'. CC sound/soc/nuc900/nuc900-ac97.o sound/soc/nuc900/nuc900-ac97.c:300: warning: initialization from incompatible pointer type sound/soc/nuc900/nuc900-ac97.c:301: warning: initialization from incompatible pointer type sound/soc/nuc900/nuc900-ac97.c:318: error: expected ',' or ';' before 'static' sound/soc/nuc900/nuc900-ac97.c:405: error: 'nuc900_ac97_drvprobe' undeclared here (not in a function) make[3]: *** [sound/soc/nuc900/nuc900-ac97.o] Error 1 make[2]: *** [sound/soc/nuc900] Error 2 make[1]: *** [sound/soc] Error 2 make: *** [sound] Error 2 Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-11-29ALSA: hda: Use BIOS auto-parsing instead of existing model quirk for MEDION MD2Daniel T Chen
BugLink: https://launchpad.net/bugs/682199 A 2.6.35 (Ubuntu Maverick) user, burningphantom1, reported a regression in audio: playback was inaudible through both speakers and headphones. In commit 272a527c04 of sound-2.6.git, a new model was added with this machine's PCI SSID. Fortunately, it is now sufficient to use the auto model for BIOS auto-parsing instead of the existing quirk. Playback, capture, and jack sense were verified working for both 2.6.35 and the alsa-driver snapshot from 2010-11-27 when model=auto is used. Reported-and-tested-by: burningphantom1 Cc: <stable@kernel.org> [2.6.35+] Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-27Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (30 commits) ALSA: hda - Use ALC_INIT_DEFAULT for really default initialization ASoC: Fix resource reclaim for osk5912 ASoC: tlv320aic3x - fix variable may be used uninitialized warning ASoC: davinci-vcif - fix a memory leak ASoC: phycore-ac97: fix resource leak ASoC: imx-ssi: fix resource leak ASoC: simone: fix resource leak in simone_init error path ASoC: sam9g20_wm8731: fix resource leak in at91sam9g20ek_init error path ASoC: snd-soc-afeb9260: remove unneeded platform_device_del in error path ASoC: pcm030-audio-fabric: fix resource leak in pcm030_fabric_init error path ASoC: efika-audio-fabric: fix resource leak in efika_fabric_init error path ASoC: Call snd_soc_unregister_dais instead of snd_soc_unregister_dai in sh4_soc_dai_remove ASoC: fix SND_PXA2XX_LIB Kconfig warning ALSA: hda - Fix ALC660-VD/ALC861-VD capture/playback mixers ALSA: HDA: Add an extra DAC for Realtek ALC887-VD ASoC: nuc900-ac97: fix a memory leak ASoC: Return proper error for omap3pandora_soc_init ASoC: wm8961 - clear WM8961_MCLKDIV bit for freq <= 16500000 ASoC: wm8961 - clear WM8961_DACSLOPE bit for normal mode ALSA: hda - Fix Acer 7730G support ...
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-04 13:37:11 +0000