| Age | Commit message (Collapse) | Author |
|---|
|
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Report received Beacon frames that do not have a valid MME MIC when
beacon protection is enabled. This covers both the cases of no MME in
the received frame and invalid MIC in the MME.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200401142548.6990-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Extend cfg80211_rx_unprot_mlme_mgmt() to cover indication of unprotected
Beacon frames in addition to the previously used Deauthentication and
Disassociation frames. The Beacon frame case is quite similar, but has
couple of exceptions: this is used both with fully unprotected and also
incorrectly protected frames and there is a rate limit on the events to
avoid unnecessary flooding netlink events in case something goes wrong.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200401142548.6990-1-jouni@codeaurora.org
[add missing kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are two bugs with this, first, it shouldn't be called
on an interface that's down, and secondly, it should then be
called when the interface comes up.
Note that the currently only user (iwlwifi) doesn't seem to
care about either of these scenarios.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200417111830.401d82c7a0bf.I5dc7d718816460c2d8d89c7af6c215f9e2b3078f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Maintain the connection AID only in sdata->vif.bss_conf.aid, not
also in sdata->u.mgd.aid.
Keep setting that where we set ifmgd->aid before, which has the
side effect of exposing the AID to the driver before the station
entry (AP) is marked associated, in case it needs it then.
Requested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20200417123802.085d4a322b0c.I2e7a2ceceea8c6880219f9e9ee4d4ac985fd295a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When setting the meter rate to 4+Gbps, there is an
overflow, the meters don't work as expected.
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before invoking the ovs_meter_cmd_reply_stats, "meter"
was checked, so don't check it agin in that function.
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't allow user to create meter unlimitedly, which may cause
to consume a large amount of kernel memory. The max number
supported is decided by physical memory and 20K meters as default.
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In kernel datapath of Open vSwitch, there are only 1024
buckets of meter in one datapath. If installing more than
1024 (e.g. 8192) meters, it may lead to the performance drop.
But in some case, for example, Open vSwitch used as edge
gateway, there should be 20K at least, where meters used for
IP address bandwidth limitation.
[Open vSwitch userspace datapath has this issue too.]
For more scalable meter, this patch use meter array instead of
hash tables, and expand/shrink the array when necessary. So we
can install more meters than before in the datapath.
Introducing the struct *dp_meter_instance, it's easy to
expand meter though changing the *ti point in the struct
*dp_meter_table.
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecassary casts in the argument to kfree.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gro_flush_timeout and napi_defer_hard_irqs can be read
from napi_complete_done() while other cpus write the value,
whithout explicit synchronization.
Use READ_ONCE()/WRITE_ONCE() to annotate the races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Back in commit 3b47d30396ba ("net: gro: add a per device gro flush timer")
we added the ability to arm one high resolution timer, that we used
to keep not-complete packets in GRO engine a bit longer, hoping that further
frames might be added to them.
Since then, we added the napi_complete_done() interface, and commit
364b6055738b ("net: busy-poll: return busypolling status to drivers")
allowed drivers to avoid re-arming NIC interrupts if we made a promise
that their NAPI poll() handler would be called in the near future.
This infrastructure can be leveraged, thanks to a new device parameter,
which allows to arm the napi hrtimer, instead of re-arming the device
hard IRQ.
We have noticed that on some servers with 32 RX queues or more, the chit-chat
between the NIC and the host caused by IRQ delivery and re-arming could hurt
throughput by ~20% on 100Gbit NIC.
In contrast, hrtimers are using local (percpu) resources and might have lower
cost.
The new tunable, named napi_defer_hard_irqs, is placed in the same hierarchy
than gro_flush_timeout (/sys/class/net/ethX/)
By default, both gro_flush_timeout and napi_defer_hard_irqs are zero.
This patch does not change the prior behavior of gro_flush_timeout
if used alone : NIC hard irqs should be rearmed as before.
One concrete usage can be :
echo 20000 >/sys/class/net/eth1/gro_flush_timeout
echo 10 >/sys/class/net/eth1/napi_defer_hard_irqs
If at least one packet is retired, then we will reset napi counter
to 10 (napi_defer_hard_irqs), ensuring at least 10 periodic scans
of the queue.
On busy queues, this should avoid NIC hard IRQ, while before this patch IRQ
avoidance was only possible if napi->poll() was exhausting its budget
and not call napi_complete_done().
This feature also can be used to work around some non-optimal NIC irq
coalescing strategies.
Having the ability to insert XX usec delays between each napi->poll()
can increase cache efficiency, since we increase batch sizes.
It also keeps serving cpus not idle too long, reducing tail latencies.
Co-developed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort of "encapsulation", and we can use the same mechs to
greatly improve overall DSA performance.
skbs are passed to the GRO layer after removing CPU tags, so we don't
need any new packet offload types as it was firstly proposed by me in
the first GRO-over-DSA variant [1].
The size of struct gro_cells is sizeof(void *), so hot struct
dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields
remain in one 32-byte cacheline.
The other positive side effect is that drivers for network devices
that can be shipped as CPU ports of DSA-driven switches can now use
napi_gro_frags() to pass skbs to kernel. Packets built that way are
completely non-linear and are likely being dropped without GRO.
This was tested on to-be-mainlined-soon Ethernet driver that uses
napi_gro_frags(), and the overall performance was on par with the
variant from [1], sometimes even better due to minimal overhead.
net.core.gro_normal_batch tuning may help to push it to the limit
on particular setups and platforms.
iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup
on 1.2 GHz MIPS board:
5.7-rc2 baseline:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender
[ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver
Iface RX packets TX packets
eth0 7097731 7097702
port0 426050 6671829
port1 6671681 425862
port1.218 6671677 425851
With this patch:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender
[ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver
Iface RX packets TX packets
eth0 9474792 9474777
port0 455200 353288
port1 9019592 455035
port1.218 353144 455024
v2:
- Add some performance examples in the commit message;
- No functional changes.
[1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/
Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC4862 5.5.3 e) prevents received Router Advertisements from reducing
the Valid Lifetime of configured addresses to less than two hours, thus
preventing hosts from reacting to the information provided by a router
that has positive knowledge that a prefix has become invalid.
This patch makes hosts honor all Valid Lifetime values, as per
draft-gont-6man-slaac-renum-06, Section 4.2. This is meant to help
mitigate the problem discussed in draft-ietf-v6ops-slaac-renum.
Note: Attacks aiming at disabling an advertised prefix via a Valid
Lifetime of 0 are not really more harmful than other attacks
that can be performed via forged RA messages, such as those
aiming at completely disabling a next-hop router via an RA that
advertises a Router Lifetime of 0, or performing a Denial of
Service (DoS) attack by advertising illegitimate prefixes via
forged PIOs. In scenarios where RA-based attacks are of concern,
proper mitigations such as RA-Guard [RFC6105] [RFC7113] should
be implemented.
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
net/caif/caif_dev.c:410:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:445:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:145:1-12: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:223:1-12: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tracepoint support for QRTR with NS as the first candidate. Later on
this can be extended to core QRTR and transport drivers.
The trace_printk() used in NS has been replaced by tracepoints.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the act_ct SW offload in flowtable, The counter of the conntrack
entry will never update. So update the nf_conn_acct conuter in act_ct
flowtable software offload.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a88c ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable rc is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interface is executing a self test, put the interface into
operative status testing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to speed, duplex and dorment, report the testing status
in sysfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 2863 defines the operational state testing. Add support for this
state, both as a IF_LINK_MODE_ and __LINK_STATE_.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-04-17
Here's the first bluetooth-next pull request for the 5.8 kernel:
- Added debugfs option to control MITM flag usage during pairing
- Added new BT_MODE socket option
- Added support for Qualcom QCA6390 device
- Added support for Realtek RTL8761B device
- Added support for mSBC audio codec over USB endpoints
- Added framework for Microsoft HCI vendor extensions
- Added new Read Security Information management command
- Fixes/cleanup to link layer privacy related code
- Various other smaller cleanups & fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
|
|
The Enhanced Connection Complete event is use in conjunction with LL
Privacy and not Extended Advertising.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
In commit 16ad3f4022bb ("tipc: introduce variable window congestion
control"), we allow link window to change with the congestion avoidance
algorithm. However, there is a bug that during the slow-start if packet
retransmission occurs, the link will enter the fast-recovery phase, set
its window to the 'ssthresh' which is never less than 300, so the link
window suddenly increases to that limit instead of decreasing.
Consequently, two issues have been observed:
- For broadcast-link: it can leave a gap between the link queues that a
new packet will be inserted and sent before the previous ones, i.e. not
in-order.
- For unicast: the algorithm does not work as expected, the link window
jumps to the slow-start threshold whereas packet retransmission occurs.
This commit fixes the issues by avoiding such the link window increase,
but still decreasing if the 'ssthresh' is lowered.
Fixes: 16ad3f4022bb ("tipc: introduce variable window congestion control")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning the error code via a 'int *ret' when the function returns a
pointer is very un-kernely and causes gcc 10's static analysis to choke:
net/rds/message.c: In function ‘rds_message_map_pages’:
net/rds/message.c:358:10: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
358 | return ERR_PTR(ret);
Use a typical ERR_PTR return instead.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-04-15
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 3 day(s) which contain
a total of 11 files changed, 238 insertions(+), 95 deletions(-).
The main changes are:
1) Fix offset overflow for BPF_MEM BPF_DW insn mapping on arm32 JIT,
from Luke Nelson and Xi Wang.
2) Prevent mprotect() to make frozen & mmap()'ed BPF map writeable
again, from Andrii Nakryiko and Jann Horn.
3) Fix type of old_fd in bpf_xdp_set_link_opts to int in libbpf and add
selftests, from Toke Høiland-Jørgensen.
4) Fix AF_XDP to check that headroom cannot be larger than the available
space in the chunk, from Magnus Karlsson.
5) Fix reset of XDP prog when expected_fd is set, from David Ahern.
6) Fix a segfault in bpftool's struct_ops command when BTF is not
available, from Daniel T. Lee.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of fixes:
* FTM responder policy netlink validation fix
(but the only user validates again later)
* kernel-doc fixes
* a fix for a race in mac80211 radio registration vs. userspace
* a mesh channel switch fix
* a fix for a syzbot reported kasprintf() issue
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
When starting active scanning for discovery the whitelist is not needed
to be used. So the filter_policy is 0x00. To make the core more readable
use a variable name instead of just setting 0 as paramter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Add a check that the headroom cannot be larger than the available
space in the chunk. In the current code, a malicious user can set the
headroom to a value larger than the chunk size minus the fixed XDP
headroom. That way packets with a length larger than the supported
size in the umem could get accepted and result in an out-of-bounds
write.
Fixes: c0c77d8fb787 ("xsk: add user memory registration support sockopt")
Reported-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207225
Link: https://lore.kernel.org/bpf/1586849715-23490-1-git-send-email-magnus.karlsson@intel.com
|
|
Previously mesh channel switch happens if beacon contains
CSA IE without checking the mesh peer info. Due to that
channel switch happens even if the beacon is not from
its own mesh peer. Fixing that by checking if the CSA
originated from the same mesh network before proceeding
for channel switch.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1585403604-29274-1-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A race condition leading to a kernel crash is observed during invocation
of ieee80211_register_hw() on a dragonboard410c device having wcn36xx
driver built as a loadable module along with a wifi manager in user-space
waiting for a wifi device (wlanX) to be active.
Sequence diagram for a particular kernel crash scenario:
user-space ieee80211_register_hw() ieee80211_tasklet_handler()
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
| | |
|<---phy0----wiphy_register() |
|-----iwd if_add---->| |
| |<---IRQ----(RX packet)
| Kernel crash |
| due to unallocated |
| workqueue. |
| | |
| alloc_ordered_workqueue() |
| | |
| Misc wiphy init. |
| | |
| ieee80211_if_add() |
| | |
As evident from above sequence diagram, this race condition isn't specific
to a particular wifi driver but rather the initialization sequence in
ieee80211_register_hw() needs to be fixed. So re-order the initialization
sequence and the updated sequence diagram would look like:
user-space ieee80211_register_hw() ieee80211_tasklet_handler()
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
| | |
| alloc_ordered_workqueue() |
| | |
| Misc wiphy init. |
| | |
|<---phy0----wiphy_register() |
|-----iwd if_add---->| |
| |<---IRQ----(RX packet)
| | |
| ieee80211_if_add() |
| | |
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1586254255-28713-1-git-send-email-sumit.garg@linaro.org
[Johannes: fix rtnl imbalances]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
DSA and CPU ports can be configured in two ways. By default, the
driver should configure such ports to there maximum bandwidth. For
most use cases, this is sufficient. When this default is insufficient,
a phylink instance can be bound to such ports, and phylink will
configure the port, e.g. based on fixed-link properties. phylink
assumes the port is initially down. Given that the driver should have
already configured it to its maximum speed, ask the driver to down
the port before instantiating the phylink instance.
Fixes: 30c4a5b0aad8 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6
socket as well as UDPv6 when trying to transmit fragmentably.
Without this, packets filled to the normal size used by the kernel AFS
client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE
immediately. The ->sk_error_report() notification hook is called, but
rxrpc doesn't generate a trace for it.
This is a temporary fix; a more permanent solution needs to involve
changing the size of the packets being filled in accordance with the MTU,
which isn't currently done in AF_RXRPC. The reason for not doing so was
that, barring the last packet in an rx jumbo packet, jumbos can only be
assembled out of 1412-byte packets - and the plan was to construct jumbos
on the fly at transmission time.
Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to
engage in this anyway since fragmentation is only done by the sender. We
can then condense the switch-statement in rxrpc_send_data_packet().
Fixes: 75b54cb57ca3 ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit mentioned in the Fixes tag reuses the local prog variable
when looking up an expected_fd. The variable is not reset when fd < 0
causing a detach with the expected_fd set to actually call
dev_xdp_install for the existing program. The end result is that the
detach does not happen.
Fixes: 92234c8f15c8 ("xdp: Support specifying expected existing program when attaching XDP")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200412133204.43847-1-dsahern@kernel.org
|
|
The nested policy here should be established using the
NLA_POLICY_NESTED() macro so the length is properly
filled in.
Cc: stable@vger.kernel.org
Fixes: 81e54d08d9d8 ("cfg80211: support FTM responder configuration/statistics")
Link: https://lore.kernel.org/r/20200412004029.9d0722bb56c8.Ie690bfcc4a1a61ff8d8ca7e475d59fcaa52fb2da@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mptcp_connect/28740 is trying to release lock (sk_lock-AF_INET) at:
[<ffffffff82c15869>] mptcp_poll+0xb9/0x550
but there are no more locks to release!
Call Trace:
lock_release+0x50f/0x750
release_sock+0x171/0x1b0
mptcp_poll+0xb9/0x550
sock_poll+0x157/0x470
? get_net_ns+0xb0/0xb0
do_sys_poll+0x63c/0xdd0
Problem is that __mptcp_tcp_fallback() releases the mptcp socket lock,
but after recent change it doesn't do this in all of its return paths.
To fix this, remove the unlock from __mptcp_tcp_fallback() and
always do the unlock in the caller.
Also add a small comment as to why we have this
__mptcp_needs_tcp_fallback().
Fixes: 0b4f33def7bbde ("mptcp: fix tcp fallback crash")
Reported-by: syzbot+e56606435b7bfeea8cf5@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-04-10
The following pull-request contains BPF updates for your *net* tree.
We've added 13 non-merge commits during the last 7 day(s) which contain
a total of 13 files changed, 137 insertions(+), 43 deletions(-).
The main changes are:
1) JIT code emission fixes for riscv and arm32, from Luke Nelson and Xi Wang.
2) Disable vmlinux BTF info if GCC_PLUGIN_RANDSTRUCT is used, from Slava Bacherikov.
3) Fix oob write in AF_XDP when meta data is used, from Li RongQing.
4) Fix bpf_get_link_xdp_id() handling on single prog when flags are specified,
from Andrey Ignatov.
5) Fix sk_assign() BPF helper for request sockets that can have sk_reuseport
field uninitialized, from Joe Stringer.
6) Fix mprotect() test case for the BPF LSM, from KP Singh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error could indicate a problem with the Bluetooth device. It
is easier to investigate if the packet's actual length gets logged,
not just the fact that a discrepancy occurred.
Signed-off-by: Daniels Umanovskis <du@axentia.se>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When CONFIG_IP_MULTICAST is not set and multicast ip is added to the device
with autojoin flag or when multicast ip is deleted kernel will crash.
steps to reproduce:
ip addr add 224.0.0.0/32 dev eth0
ip addr del 224.0.0.0/32 dev eth0
or
ip addr add 224.0.0.0/32 dev eth0 autojoin
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
pc : _raw_write_lock_irqsave+0x1e0/0x2ac
lr : lock_sock_nested+0x1c/0x60
Call trace:
_raw_write_lock_irqsave+0x1e0/0x2ac
lock_sock_nested+0x1c/0x60
ip_mc_config.isra.28+0x50/0xe0
inet_rtm_deladdr+0x1a8/0x1f0
rtnetlink_rcv_msg+0x120/0x350
netlink_rcv_skb+0x58/0x120
rtnetlink_rcv+0x14/0x20
netlink_unicast+0x1b8/0x270
netlink_sendmsg+0x1a0/0x3b0
____sys_sendmsg+0x248/0x290
___sys_sendmsg+0x80/0xc0
__sys_sendmsg+0x68/0xc0
__arm64_sys_sendmsg+0x20/0x30
el0_svc_common.constprop.2+0x88/0x150
do_el0_svc+0x20/0x80
el0_sync_handler+0x118/0x190
el0_sync+0x140/0x180
Fixes: 93a714d6b53d ("multicast: Extend ip address command to enable multicast group join/leave on")
Signed-off-by: Taras Chornyi <taras.chornyi@plvision.eu>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rds_free_mr(), it calls rds_destroy_mr(mr) directly. But this
defeats the purpose of reference counting and makes MR free handling
impossible. It means that holding a reference does not guarantee that
it is safe to access some fields. For example, In
rds_cmsg_rdma_dest(), it increases the ref count, unlocks and then
calls mr->r_trans->sync_mr(). But if rds_free_mr() (and
rds_destroy_mr()) is called in between (there is no lock preventing
this to happen), r_trans_private is set to NULL, causing a panic.
Similar issue is in rds_rdma_unuse().
Reported-by: zerons <sironhide0null@gmail.com>
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And removed rds_mr_put().
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the local node id(qrtr_local_nid) is not modified after its
initialization, it equals to the broadcast node id(QRTR_NODE_BCAST).
So the messages from local node should not be taken as broadcast
and keep the process going to send them out anyway.
The definitions are as follow:
static unsigned int qrtr_local_nid = NUMA_NO_NODE;
Fixes: fdf5fd397566 ("net: qrtr: Broadcast messages only from control port")
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
