| Age | Commit message (Collapse) | Author |
|---|
|
The ax.25 socket connection timed out & the sock struct has been
previously taken down ie. sock struct is now a NULL pointer. Checking
the sock_flag causes the segfault. Check if the socket struct pointer
is NULL before checking sock_flag. This segfault is seen in
timed out netrom connections.
Please submit to -stable.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 7bd509e311f4 ("bpf: add prog_digest and expose it via
fdinfo/netlink") was recently discussed, partially due to
admittedly suboptimal name of "prog_digest" in combination
with sha1 hash usage, thus inevitably and rightfully concerns
about its security in terms of collision resistance were
raised with regards to use-cases.
The intended use cases are for debugging resp. introspection
only for providing a stable "tag" over the instruction sequence
that both kernel and user space can calculate independently.
It's not usable at all for making a security relevant decision.
So collisions where two different instruction sequences generate
the same tag can happen, but ideally at a rather low rate. The
"tag" will be dumped in hex and is short enough to introspect
in tracepoints or kallsyms output along with other data such
as stack trace, etc. Thus, this patch performs a rename into
prog_tag and truncates the tag to a short output (64 bits) to
make it obvious it's not collision-free.
Should in future a hash or facility be needed with a security
relevant focus, then we can think about requirements, constraints,
etc that would fit to that situation. For now, rework the exposed
parts for the current use cases as long as nothing has been
released yet. Tested on x86_64 and s390x.
Fixes: 7bd509e311f4 ("bpf: add prog_digest and expose it via fdinfo/netlink")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sctp_frag_point() doesn't store anything, and thus just calling it
cannot do anything useful.
sctp_apply_peer_addr_params is only called by
sctp_setsockopt_peer_addr_params. When operating on an asoc,
sctp_setsockopt_peer_addr_params will call sctp_apply_peer_addr_params
once for the asoc, and then once for each transport this asoc has,
meaning that the frag_point will be recomputed when updating the
transports and calling it when updating the asoc is not necessary.
IOW, no action is needed here and we can remove this call.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assigned but not used.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arp is being checked instead of arp_eth to see if the call to
__skb_header_pointer failed. Fix this by checking arp_eth is
null instead of arp. Also fix to use length hlen rather than
hlen - sizeof(_arp); thanks to Eric Dumazet for spotting
this latter issue.
CoverityScan CID#1396428 ("Logically dead code") on 2nd
arp comparison (which should be arp_eth instead).
Fixes: commit 55733350e5e8b70c5 ("flow disector: ARP support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit d35c99ff77ecb ("netlink: do not enter direct reclaim from
netlink_dump()") we made sure to not trigger expensive memory reclaim.
Problem is that a bit later, netlink_trim() might be called and
trigger memory reclaim.
netlink_trim() should be best effort, and really as fast as possible.
Under memory pressure, it is fine to not trim this skb.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we allocate memory always with GFP_ATOMIC flag.
When the system is under memory pressure and a user tries to send,
the send fails due to low memory. However, the user application
can wait for free memory if we allocate it using GFP_KERNEL flag.
In this commit, we use allocate memory with GFP_KERNEL for all user
allocation.
Reported-by: Rune Torgersen <runet@innovsys.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With ip6gre we have a tunnel header which also makes the tunnel MTU
smaller. We need to reserve room for it. Previously we were using up
space reserved for the Tunnel Encapsulation Limit option
header (RFC 2473).
Also, after commit b05229f44228 ("gre6: Cleanup GREv6 transmit path,
call common GRE functions") our contract with the caller has
changed. Now we check if the packet length exceeds the tunnel MTU after
the tunnel header has been pushed, unlike before.
This is reflected in the check where we look at the packet length minus
the size of the tunnel header, which is already accounted for in tunnel
MTU.
Fixes: b05229f44228 ("gre6: Cleanup GREv6 transmit path, call common GRE functions")
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an IPv6 version of commit 24803f38a5c0 ("igmp: do not remove igmp
souce list..."). In mld_del_delrec(), we will restore back all source filter
info instead of flush them.
Move mld_clear_delrec() from ipv6_mc_down() to ipv6_mc_destroy_dev() since
we should not remove source list info when set link down. Remove
igmp6_group_dropped() in ipv6_mc_destroy_dev() since we have called it in
ipv6_mc_down().
Also clear all source info after igmp6_group_dropped() instead of in it
because ipv6_mc_down() will call igmp6_group_dropped().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull nfsd fixes from Bruce Fields:
"Miscellaneous nfsd bugfixes, one for a 4.10 regression, three for
older bugs"
* tag 'nfsd-4.10-1' of git://linux-nfs.org/~bfields/linux:
svcrdma: avoid duplicate dma unmapping during error recovery
sunrpc: don't call sleeping functions from the notifier block callbacks
svcrpc: don't leak contexts on PROC_DESTROY
nfsd: fix supported attributes for acl & labels
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have a number of fixes, in part because I was late
in actually sending them out - will try to do better in
the future:
* handle VHT opmode properly when hostapd is controlling
full station state
* two fixes for minimum channel width in mac80211
* don't leave SMPS set to junk in HT capabilities
* fix headroom when forwarding mesh packets, recently
broken by another fix that failed to take into account
frame encryption
* fix the TID in null-data packets indicating EOSP (end
of service period) in U-APSD
* prevent attempting to use (and then failing which
results in crashes) TXQs on stations that aren't added
to the driver yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When executing conntrack actions on skbuffs with checksum mode
CHECKSUM_COMPLETE, the checksum must be updated to account for
header pushes and pulls. Otherwise we get "hw csum failure"
logs similar to this (ICMP packet received on geneve tunnel
via ixgbe NIC):
[ 405.740065] genev_sys_6081: hw csum failure
[ 405.740106] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G I 4.10.0-rc3+ #1
[ 405.740108] Call Trace:
[ 405.740110] <IRQ>
[ 405.740113] dump_stack+0x63/0x87
[ 405.740116] netdev_rx_csum_fault+0x3a/0x40
[ 405.740118] __skb_checksum_complete+0xcf/0xe0
[ 405.740120] nf_ip_checksum+0xc8/0xf0
[ 405.740124] icmp_error+0x1de/0x351 [nf_conntrack_ipv4]
[ 405.740132] nf_conntrack_in+0xe1/0x550 [nf_conntrack]
[ 405.740137] ? find_bucket.isra.2+0x62/0x70 [openvswitch]
[ 405.740143] __ovs_ct_lookup+0x95/0x980 [openvswitch]
[ 405.740145] ? netif_rx_internal+0x44/0x110
[ 405.740149] ovs_ct_execute+0x147/0x4b0 [openvswitch]
[ 405.740153] do_execute_actions+0x22e/0xa70 [openvswitch]
[ 405.740157] ovs_execute_actions+0x40/0x120 [openvswitch]
[ 405.740161] ovs_dp_process_packet+0x84/0x120 [openvswitch]
[ 405.740166] ovs_vport_receive+0x73/0xd0 [openvswitch]
[ 405.740168] ? udp_rcv+0x1a/0x20
[ 405.740170] ? ip_local_deliver_finish+0x93/0x1e0
[ 405.740172] ? ip_local_deliver+0x6f/0xe0
[ 405.740174] ? ip_rcv_finish+0x3a0/0x3a0
[ 405.740176] ? ip_rcv_finish+0xdb/0x3a0
[ 405.740177] ? ip_rcv+0x2a7/0x400
[ 405.740180] ? __netif_receive_skb_core+0x970/0xa00
[ 405.740185] netdev_frame_hook+0xd3/0x160 [openvswitch]
[ 405.740187] __netif_receive_skb_core+0x1dc/0xa00
[ 405.740194] ? ixgbe_clean_rx_irq+0x46d/0xa20 [ixgbe]
[ 405.740197] __netif_receive_skb+0x18/0x60
[ 405.740199] netif_receive_skb_internal+0x40/0xb0
[ 405.740201] napi_gro_receive+0xcd/0x120
[ 405.740204] gro_cell_poll+0x57/0x80 [geneve]
[ 405.740206] net_rx_action+0x260/0x3c0
[ 405.740209] __do_softirq+0xc9/0x28c
[ 405.740211] irq_exit+0xd9/0xf0
[ 405.740213] do_IRQ+0x51/0xd0
[ 405.740215] common_interrupt+0x93/0x93
Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch disables FACK by default as RACK is the successor of FACK
(inspired by the insights behind FACK).
FACK[1] in Linux works as follows: a packet P is deemed lost,
if packet Q of higher sequence is s/acked and P and Q are distant
by at least dupthresh number of packets in sequence space.
FACK is more aggressive than the IETF recommened recovery for SACK
(RFC3517 A Conservative Selective Acknowledgment (SACK)-based Loss
Recovery Algorithm for TCP), because a single SACK may trigger
fast recovery. This obviously won't work well with reordering so
FACK is dynamically disabled upon detecting reordering.
RACK supersedes FACK by using time distance instead of sequence
distance. On reordering, RACK waits for a quarter of RTT receiving
a single SACK before starting recovery. (the timer can be made more
adaptive in the future by measuring reordering distance in time,
but currently RTT/4 seem to work well.) Once the recovery starts,
RACK behaves almost like FACK because it reduces the reodering
window to 1ms, so it fast retransmits quickly. In addition RACK
can detect loss retransmission as it does not care about the packet
sequences (being repeated or not), which is extremely useful when
the connection is going through a traffic policer.
Google server experiments indicate that disabling FACK after enabling
RACK has negligible impact on the overall loss recovery performance
with more reordering events detected. But we still keep the FACK
implementation for backup if RACK has bugs that needs to be disabled.
[1] M. Mathis, J. Mahdavi, "Forward Acknowledgment: Refining
TCP Congestion Control," In Proceedings of SIGCOMM '96, August 1996.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thin stream DUPACK is to start fast recovery on only one DUPACK
provided the connection is a thin stream (i.e., low inflight). But
this older feature is now subsumed with RACK. If a connection
receives only a single DUPACK, RACK would arm a reordering timer
and soon starts fast recovery instead of timeout if no further
ACKs are received.
The socket option (THIN_DUPACK) is kept as a nop for compatibility.
Note that this patch does not change another thin-stream feature
which enables linear RTO. Although it might be good to generalize
that in the future (i.e., linear RTO for the first say 3 retries).
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the (partial) implementation of the aggressive
limited transmit in RFC4653 TCP Non-Congestion Robustness (NCR).
NCR is a mitigation to the problem created by the dynamic
DUPACK threshold. With the current adaptive DUPACK threshold
(tp->reordering) could cause timeouts by preventing fast recovery.
For example, if the last packet of a cwnd burst was reordered, the
threshold will be set to the size of cwnd. But if next application
burst is smaller than threshold and has drops instead of reorderings,
the sender would not trigger fast recovery but instead resorts to a
timeout recovery.
NCR mitigates this issue by checking the number of DUPACKs against
the current flight size additionally. The techniqueue is similar to
the early retransmit RFC.
With RACK loss detection, this mitigation is not needed, because RACK
does not use DUPACK threshold to detect losses. RACK arms a reordering
timer to fire at most a quarter RTT later to start fast recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the support of RFC5827 early retransmit (i.e.,
fast recovery on small inflight with <3 dupacks) because it is
subsumed by the new RACK loss detection. More specifically when
RACK receives DUPACKs, it'll arm a reordering timer to start fast
recovery after a quarter of (min)RTT, hence it covers the early
retransmit except RACK does not limit itself to specific inflight
or dupack numbers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Forward retransmit is an esoteric feature in RFC3517 (condition(3)
in the NextSeg()). Basically if a packet is not considered lost by
the current criteria (# of dupacks etc), but the congestion window
has room for more packets, then retransmit this packet.
However it actually conflicts with the rest of recovery design. For
example, when reordering is detected we want to be conservative
in retransmitting packets but forward-retransmit feature would
break that to force more retransmission. Also the implementation is
fairly complicated inside the retransmission logic inducing extra
iterations in the write queue. With RACK losses are being detected
timely and this heuristic is no longer necessary. There this patch
removes the feature.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current F-RTO reverts cwnd reset whenever a never-retransmitted
packet was (s)acked. The timeout can be declared spurious because
the packets acknoledged with this ACK was transmitted before the
timeout, so clearly not all the packets are lost to reset the cwnd.
This nice detection does not really depend F-RTO internals. This
patch applies the detection universally. On Google servers this
change detected 20% more spurious timeouts.
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes two things:
1. Start fast recovery with RACK in addition to other heuristics
(e.g., DUPACK threshold, FACK). Prior to this change RACK
is enabled to detect losses only after the recovery has
started by other algorithms.
2. Disable TCP early retransmit. RACK subsumes the early retransmit
with the new reordering timer feature. A latter patch in this
series removes the early retransmit code.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently RACK would mark loss before the undo operations in TCP
loss recovery. This could incorrectly identify real losses as
spurious. For example a sender first experiences a delay spike and
then eventually some packets were lost due to buffer overrun.
In this case, the sender should perform fast recovery b/c not all
the packets were lost.
But the sender may first trigger a (spurious) RTO and reset
cwnd to 1. The following ACKs may used to mark real losses by
tcp_rack_mark_lost. Then in tcp_process_loss this ACK could trigger
F-RTO undo condition and unmark real losses and revert the cwnd
reduction. If there are no more ACKs coming back, eventually the
sender would timeout again instead of performing fast recovery.
The patch fixes this incorrect process by always performing
the undo checks before detecting losses.
Fixes: 4f41b1c58a32 ("tcp: use RACK to detect losses")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The packets inside a jumbo skb (e.g., TSO) share the same skb
timestamp, even though they are sent sequentially on the wire. Since
RACK is based on time, it can not detect some packets inside the
same skb are lost. However, we can leverage the packet sequence
numbers as extended timestamps to detect losses. Therefore, when
RACK timestamp is identical to skb's timestamp (i.e., one of the
packets of the skb is acked or sacked), we use the sequence numbers
of the acked and unacked packets to break ties.
We can use the same sequence logic to advance RACK xmit time as
well to detect more losses and avoid timeout.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes RACK install a reordering timer when it suspects
some packets might be lost, but wants to delay the decision
a little bit to accomodate reordering.
It does not create a new timer but instead repurposes the existing
RTO timer, because both are meant to retransmit packets.
Specifically it arms a timer ICSK_TIME_REO_TIMEOUT when
the RACK timing check fails. The wait time is set to
RACK.RTT + RACK.reo_wnd - (NOW - Packet.xmit_time) + fudge
This translates to expecting a packet (Packet) should take
(RACK.RTT + RACK.reo_wnd + fudge) to deliver after it was sent.
When there are multiple packets that need a timer, we use one timer
with the maximum timeout. Therefore the timer conservatively uses
the maximum window to expire N packets by one timeout, instead of
N timeouts to expire N packets sent at different times.
The fudge factor is 2 jiffies to ensure when the timer fires, all
the suspected packets would exceed the deadline and be marked lost
by tcp_rack_detect_loss(). It has to be at least 1 jiffy because the
clock may tick between calling icsk_reset_xmit_timer(timeout) and
actually hang the timer. The next jiffy is to lower-bound the timeout
to 2 jiffies when reo_wnd is < 1ms.
When the reordering timer fires (tcp_rack_reo_timeout): If we aren't
in Recovery we'll enter fast recovery and force fast retransmit.
This is very similar to the early retransmit (RFC5827) except RACK
is not constrained to only enter recovery for small outstanding
flights.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Record the most recent RTT in RACK. It is often identical to the
"ca_rtt_us" values in tcp_clean_rtx_queue. But when the packet has
been retransmitted, RACK choses to believe the ACK is for the
(latest) retransmitted packet if the RTT is over minimum RTT.
This requires passing the arrival time of the most recent ACK to
RACK routines. The timestamp is now recorded in the "ack_time"
in tcp_sacktag_state during the ACK processing.
This patch does not change the RACK algorithm itself. It only adds
the RTT variable to prepare the next main patch.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new helper tcp_rack_detect_loss to prepare the upcoming
RACK reordering timer patch.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new helper tcp_rack_mark_skb_lost to prepare the
upcoming RACK reordering timer support.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up a data alignment issue on sparc by swapping the order
of the cookie byte array field with the length field in
struct tcp_fastopen_cookie, and making it a proper union
to clean up the typecasting.
This addresses log complaints like these:
log_unaligned: 113 callbacks suppressed
Kernel unaligned access at TPC[976490] tcp_try_fastopen+0x2d0/0x360
Kernel unaligned access at TPC[9764ac] tcp_try_fastopen+0x2ec/0x360
Kernel unaligned access at TPC[9764c8] tcp_try_fastopen+0x308/0x360
Kernel unaligned access at TPC[9764e4] tcp_try_fastopen+0x324/0x360
Kernel unaligned access at TPC[976490] tcp_try_fastopen+0x2d0/0x360
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_PREEMPT=y, CONFIG_IPV6=m and CONFIG_SEG6_HMAC=y,
seg6_hmac_init() is called during the initialization of the ipv6 module.
This causes a subsequent call to smp_processor_id() with preemption
enabled, resulting in the following trace.
[ 20.451460] BUG: using smp_processor_id() in preemptible [00000000] code: systemd/1
[ 20.452556] caller is debug_smp_processor_id+0x17/0x19
[ 20.453304] CPU: 0 PID: 1 Comm: systemd Not tainted 4.9.0-rc5-00973-g46738b1 #1
[ 20.454406] ffffc9000062fc18 ffffffff813607b2 0000000000000000 ffffffff81a7f782
[ 20.455528] ffffc9000062fc48 ffffffff813778dc 0000000000000000 00000000001dcf98
[ 20.456539] ffffffffa003bd08 ffffffff81af93e0 ffffc9000062fc58 ffffffff81377905
[ 20.456539] Call Trace:
[ 20.456539] [<ffffffff813607b2>] dump_stack+0x63/0x7f
[ 20.456539] [<ffffffff813778dc>] check_preemption_disabled+0xd1/0xe3
[ 20.456539] [<ffffffff81377905>] debug_smp_processor_id+0x17/0x19
[ 20.460260] [<ffffffffa0061f3b>] seg6_hmac_init+0xfa/0x192 [ipv6]
[ 20.460260] [<ffffffffa0061ccc>] seg6_init+0x39/0x6f [ipv6]
[ 20.460260] [<ffffffffa006121a>] inet6_init+0x21a/0x321 [ipv6]
[ 20.460260] [<ffffffffa0061000>] ? 0xffffffffa0061000
[ 20.460260] [<ffffffff81000457>] do_one_initcall+0x8b/0x115
[ 20.460260] [<ffffffff811328a3>] do_init_module+0x53/0x1c4
[ 20.460260] [<ffffffff8110650a>] load_module+0x1153/0x14ec
[ 20.460260] [<ffffffff81106a7b>] SYSC_finit_module+0x8c/0xb9
[ 20.460260] [<ffffffff81106a7b>] ? SYSC_finit_module+0x8c/0xb9
[ 20.460260] [<ffffffff81106abc>] SyS_finit_module+0x9/0xb
[ 20.460260] [<ffffffff810014d1>] do_syscall_64+0x62/0x75
[ 20.460260] [<ffffffff816834f0>] entry_SYSCALL64_slow_path+0x25/0x25
Moreover, dst_cache_* functions also call smp_processor_id(), generating
a similar trace.
This patch uses raw_cpu_ptr() in seg6_hmac_init() rather than this_cpu_ptr()
and disable preemption when using dst_cache_* functions.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Station structure is considered as not uploaded
(to driver) until drv_sta_state() finishes. This
call is however done after the structure is
attached to mac80211 internal lists and hashes.
This means mac80211 can lookup (and use) station
structure before it is uploaded to a driver.
If this happens (structure exists, but
sta->uploaded is false) fast_tx path can still be
taken. Deep in the fastpath call the sta->uploaded
is checked against to derive "pubsta" argument for
ieee80211_get_txq(). If sta->uploaded is false
(and sta is actually non-NULL) ieee80211_get_txq()
effectively downgraded to vif->txq.
At first glance this may look innocent but coerces
mac80211 into a state that is almost guaranteed
(codel may drop offending skb) to crash because a
station-oriented skb gets queued up on
vif-oriented txq. The ieee80211_tx_dequeue() ends
up looking at info->control.flags and tries to use
txq->sta which in the fail case is NULL.
It's probably pointless to pretend one can
downgrade skb from sta-txq to vif-txq.
Since downgrading unicast traffic to vif->txq must
not be done there's no txq to put a frame on if
sta->uploaded is false. Therefore the code is made
to fall back to regular tx() op path if the
described condition is hit.
Only drivers using wake_tx_queue were affected.
Example crash dump before fix:
Unable to handle kernel paging request at virtual address ffffe26c
PC is at ieee80211_tx_dequeue+0x204/0x690 [mac80211]
[<bf4252a4>] (ieee80211_tx_dequeue [mac80211]) from
[<bf4b1388>] (ath10k_mac_tx_push_txq+0x54/0x1c0 [ath10k_core])
[<bf4b1388>] (ath10k_mac_tx_push_txq [ath10k_core]) from
[<bf4bdfbc>] (ath10k_htt_txrx_compl_task+0xd78/0x11d0 [ath10k_core])
[<bf4bdfbc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<bf51c5a4>] (ath10k_pci_napi_poll+0x54/0xe8 [ath10k_pci])
[<bf51c5a4>] (ath10k_pci_napi_poll [ath10k_pci]) from
[<c0572e90>] (net_rx_action+0xac/0x160)
Reported-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ibss and mesh modes copy the ht capabilites from the band without
overriding the SMPS state. Unfortunately the default value 0 for the
SMPS field means static SMPS instead of disabled.
This results in HT ibss and mesh setups using only single-stream rates,
even though SMPS is not supposed to be active.
Initialize SMPS to disabled for all bands on ieee80211_hw_register to
ensure that the value is sane where it is not overriden with the real
SMPS state.
Reported-by: Elektra Wagenrad <onelektra@gmx.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[move VHT TODO comment to a better place]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This enhances the connect timeout API to also carry the reason for the
timeout. These reason codes for the connect time out are represented by
enum nl80211_timeout_reason and are passed to user space through a new
attribute NL80211_ATTR_TIMEOUT_REASON (u32).
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[keep gfp_t argument last]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Enhance sched scan to support option of finding a better BSS while in
connected state. Firmware scans the medium and reports when it finds a
known BSS which has better RSSI than the current connected BSS. New
attributes to specify the relative RSSI (compared to the current BSS)
are added to the sched scan to implement this.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support to use a random local address (Address 2 = TA in transmit
and the same address in receive functionality) for Public Action frames
in order to improve privacy of WLAN clients. Applications fill the
random transmit address in the frame buffer in the NL80211_CMD_FRAME
command. This can be used only with the drivers that indicate support
for random local address by setting the new
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA and/or
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA_CONNECTED in ext_features.
The driver needs to configure receive behavior to accept frames to the
specified random address during the time the frame exchange is pending
and such frames need to be acknowledged similarly to frames sent to the
local permanent address when this random address functionality is not
used.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With 78, 111 and 85 bytes respectively (on x86-64), the
functions iwe_stream_add_event(), iwe_stream_add_point()
and iwe_stream_add_value() really shouldn't be inlines.
It appears that at least my compiler already decided
the same, and created a single instance of each one
of them for each file using it, but that's still a
number of instances in the system overall, which this
reduces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Current allocations are not NUMA aware, and lack proper
cleanup in case of error.
It is perfectly fine to use static per cpu allocations for 256 bytes
per cpu.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Lebrun <david.lebrun@uclouvain.be>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently we started using ipmr with thousands of entries and easily hit
soft lockups on smaller devices. The reason is that the hash function
uses the high order bits from the src and dst, but those don't change in
many common cases, also the hash table is only 64 elements so with
thousands it doesn't scale at all.
This patch migrates the hash table to rhashtable, and in particular the
rhl interface which allows for duplicate elements to be chained because
of the MFC_PROXY support (*,G; *,*,oif cases) which allows for multiple
duplicate entries to be added with different interfaces (IMO wrong, but
it's been in for a long time).
And here are some results from tests I've run in a VM:
mr_table size (default, allocated for all namespaces):
Before After
49304 bytes 2400 bytes
Add 65000 routes (the diff is much larger on smaller devices):
Before After
1m42s 58s
Forwarding 256 byte packets with 65000 routes (test done in a VM):
Before After
3 Mbps / ~1465 pps 122 Mbps / ~59000 pps
As a bonus we no longer see the soft lockups on smaller devices which
showed up even with 2000 entries before.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rdma_read_chunk_frmr() when ib_post_send() fails, the error code path
invokes ib_dma_unmap_sg() to unmap the sg list. It then invokes
svc_rdma_put_frmr() which in turn tries to unmap the same sg list through
ib_dma_unmap_sg() again. This second unmap is invalid and could lead to
problems when the iova being unmapped is subsequently reused. Remove
the call to unmap in rdma_read_chunk_frmr() and let svc_rdma_put_frmr()
handle it.
Fixes: 412a15c0fe53 ("svcrdma: Port to new memory registration API")
Cc: stable@vger.kernel.org
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Fixes following warnings :
net/core/secure_seq.c:125:28: warning: incorrect type in argument 1
(different base types)
net/core/secure_seq.c:125:28: expected unsigned int const [unsigned]
[usertype] a
net/core/secure_seq.c:125:28: got restricted __be32 [usertype] saddr
net/core/secure_seq.c:125:35: warning: incorrect type in argument 2
(different base types)
net/core/secure_seq.c:125:35: expected unsigned int const [unsigned]
[usertype] b
net/core/secure_seq.c:125:35: got restricted __be32 [usertype] daddr
net/core/secure_seq.c:125:43: warning: cast from restricted __be16
net/core/secure_seq.c:125:61: warning: restricted __be16 degrades to
integer
Fixes: 7cd23e5300c1 ("secure_seq: use SipHash in place of MD5")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The inet6addr_chain is an atomic notifier chain, so we can't call
anything that might sleep (like lock_sock)... instead of closing the
socket from svc_age_temp_xprts_now (which is called by the notifier
function), just have the rpc service threads do it instead.
Cc: stable@vger.kernel.org
Fixes: c3d4879e01be "sunrpc: Add a function to close..."
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Context expiry times are in units of seconds since boot, not unix time.
The use of get_seconds() here therefore sets the expiry time decades in
the future. This prevents timely freeing of contexts destroyed by
client RPC_GSS_PROC_DESTROY requests. We'd still free them eventually
(when the module is unloaded or the container shut down), but a lot of
contexts could pile up before then.
Cc: stable@vger.kernel.org
Fixes: c5b29f885afe "sunrpc: use seconds since boot in expiry cache"
Reported-by: Andy Adamson <andros@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
rtm_table is an 8-bit field while table ids are allowed up to u32. Commit
709772e6e065 ("net: Fix routing tables with id > 255 for legacy software")
added the preference to set rtm_table in dumps to RT_TABLE_COMPAT if the
table id is > 255. The table id returned on get route requests should do
the same.
Fixes: c36ba6603a11 ("net: Allow user to get table id from route lookup")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle failure in lwtunnel_fill_encap adding attributes to skb.
Fixes: 571e722676fe ("ipv4: support for fib route lwtunnel encap attributes")
Fixes: 19e42e451506 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
net/core/lwt_bpf.c:355:5: warning:
symbol 'bpf_lwt_prog_cmp' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When structs are used to store temporary state in cb[] buffer that is
used with programs and among tail calls, then the generated code will
not always access the buffer in bpf_w chunks. We can ease programming
of it and let this act more natural by allowing for aligned b/h/w/dw
sized access for cb[] ctx member. Various test cases are attached as
well for the selftest suite. Potentially, this can also be reused for
other program types to pass data around.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when calling convert_ctx_access() callback for the various
program types, we pass in insn->dst_reg, insn->src_reg, insn->off from
the original instruction. This information is needed to rewrite the
instruction that is based on the user ctx structure into a kernel
representation for the ctx. As we'd like to allow access size beyond
just BPF_W, we'd need also insn->code for that in order to decode the
original access size. Given that, lets just pass insn directly to the
convert_ctx_access() callback and work on that to not clutter the
callback with even more arguments we need to pass when everything is
already contained in insn. So lets go through that once, no functional
change.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating an SMC connection, there is a CLC (connection layer control)
handshake to prepare for RDMA traffic. The corresponding code is part of
commit 0cfdd8f92cac ("smc: connection and link group creation").
Mac addresses to be exchanged in the handshake are copied with a wrong
length of 12 instead of 6 bytes. Following code overwrites the wrongly
copied code, but nevertheless the correct length should already be used for
the preceding mac address copying. Use ETH_ALEN for the memcpy length with
mac addresses.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Fixes: 0cfdd8f92cac ("smc: connection and link group creation")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When introducing the new socket family AF_SMC in
commit ac7138746e14 ("smc: establish new socket family"),
a typo in af_family_clock_key_strings has slipped in.
This patch repairs it.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Fixes: ac7138746e14 ("smc: establish new socket family")
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_wake_subqueue() is duplicating the same thing that netif_tx_wake_queue()
does, so make it call it directly after looking up the queue from the index.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There may be situations in which the in-kernel originator of an
SKB cares about its wifi transmission status. To have that, set
the wifi_acked[_valid] bits before freeing/orphaning the SKB if
the destructor is set. The originator can then use it in there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a flag that indicates that the WEP ICV was stripped from an
RX packet, allowing the device to not transfer that if it's
already checked.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
