Age | Commit message (Collapse) | Author |
|
Tariq repored local pings to linklocal address is failing:
$ ifconfig ens8
ens8: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 11.141.16.6 netmask 255.255.0.0 broadcast 11.141.255.255
inet6 fe80::7efe:90ff:fecb:7502 prefixlen 64 scopeid 0x20<link>
ether 7c:fe:90:cb:75:02 txqueuelen 1000 (Ethernet)
RX packets 12 bytes 1164 (1.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 30 bytes 2484 (2.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
$ /bin/ping6 -c 3 fe80::7efe:90ff:fecb:7502%ens8
PING fe80::7efe:90ff:fecb:7502%ens8(fe80::7efe:90ff:fecb:7502) 56 data bytes
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When forwarding or sending out an ICMPv6 error, look at the embedded
packet that triggered the error and compute a flow hash over its
headers.
This let's us route the ICMP error together with the flow it belongs to
when multipath (ECMP) routing is in use, which in turn makes Path MTU
Discovery work in ECMP load-balanced or anycast setups (RFC 7690).
Granted, end-hosts behind the ECMP router (aka servers) need to reflect
the IPv6 Flow Label for PMTUD to work.
The code is organized to be in parallel with ipv4 stack:
ip_multipath_l3_keys -> ip6_multipath_l3_keys
fib_multipath_hash -> rt6_multipath_hash
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One nagging difference between ipv4 and ipv6 is host routes for ipv6
addresses are installed using the loopback device or VRF / L3 Master
device. e.g.,
2001:db8:1::/120 dev veth0 proto kernel metric 256 pref medium
local 2001:db8:1::1 dev lo table local proto kernel metric 0 pref medium
Using the loopback device is convenient -- necessary for local tx, but
has some nasty side effects, most notably setting the 'lo' device down
causes all host routes for all local IPv6 address to be removed from the
FIB and completely breaks IPv6 networking across all interfaces.
This patch puts FIB entries for IPv6 routes against the device. This
simplifies the routes in the FIB, for example by making dst->dev and
rt6i_idev->dev the same (a future patch can look at removing the device
reference taken for rt6i_idev for FIB entries).
When copies are made on FIB lookups, the cloned route has dst->dev
set to loopback (or the L3 master device). This is needed for the
local Tx of packets to local addresses.
With fib entries allocated against the real network device, the addrconf
code that reinserts host routes on admin up of 'lo' is no longer needed.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited. This was broken by
commit c0303efeab73 ("net: reduce cycles spend on ICMP replies that
gets rate limited").
An ICMP response will usually be routed back-out the same incoming
interface. Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback. In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow(). Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").
This seems to fix the reproducer given by Florian. While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).
Fixes: c0303efeab73 ("net: reduce cycles spend on ICMP replies that gets rate limited")
Reported-by: Florian Weimer <fweimer@redhat.com>
Reported-by: "H.J. Lu" <hjl.tools@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to avoid the atomic operation in icmp{v6,}_xmit_lock,
by checking the sysctl_icmp_msgs_per_sec ratelimit before these calls,
as pointed out by Eric Dumazet, but the BH disabled state must be correct.
The icmp_global_allow() call states it must be called with BH
disabled. This protection was given by the calls icmp_xmit_lock and
icmpv6_xmit_lock. Thus, split out local_bh_disable/enable from these
functions and maintain it explicitly at callers.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch split the global and per (inet)peer ICMP-reply limiter
code, and moves the global limit check to earlier in the packet
processing path. Thus, avoid spending cycles on ICMP replies that
gets limited/suppressed anyhow.
The global ICMP rate limiter icmp_global_allow() is a good solution,
it just happens too late in the process. The kernel goes through the
full route lookup (return path) for the ICMP message, before taking
the rate limit decision of not sending the ICMP reply.
Details: The kernels global rate limiter for ICMP messages got added
in commit 4cdf507d5452 ("icmp: add a global rate limitation"). It is
a token bucket limiter with a global lock. It brilliantly avoids
locking congestion by only updating when 20ms (HZ/50) were elapsed. It
can then avoids taking lock when credit is exhausted (when under
pressure) and time constraint for refill is not yet meet.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey reported the following while fuzzing the kernel with syzkaller:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 3859 Comm: a.out Not tainted 4.9.0-rc6+ #429
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff8800666d4200 task.stack: ffff880067348000
RIP: 0010:[<ffffffff833617ec>] [<ffffffff833617ec>]
icmp6_send+0x5fc/0x1e30 net/ipv6/icmp.c:451
RSP: 0018:ffff88006734f2c0 EFLAGS: 00010206
RAX: ffff8800666d4200 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: dffffc0000000000 RDI: 0000000000000018
RBP: ffff88006734f630 R08: ffff880064138418 R09: 0000000000000003
R10: dffffc0000000000 R11: 0000000000000005 R12: 0000000000000000
R13: ffffffff84e7e200 R14: ffff880064138484 R15: ffff8800641383c0
FS: 00007fb3887a07c0(0000) GS:ffff88006cc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000000 CR3: 000000006b040000 CR4: 00000000000006f0
Stack:
ffff8800666d4200 ffff8800666d49f8 ffff8800666d4200 ffffffff84c02460
ffff8800666d4a1a 1ffff1000ccdaa2f ffff88006734f498 0000000000000046
ffff88006734f440 ffffffff832f4269 ffff880064ba7456 0000000000000000
Call Trace:
[<ffffffff83364ddc>] icmpv6_param_prob+0x2c/0x40 net/ipv6/icmp.c:557
[< inline >] ip6_tlvopt_unknown net/ipv6/exthdrs.c:88
[<ffffffff83394405>] ip6_parse_tlv+0x555/0x670 net/ipv6/exthdrs.c:157
[<ffffffff8339a759>] ipv6_parse_hopopts+0x199/0x460 net/ipv6/exthdrs.c:663
[<ffffffff832ee773>] ipv6_rcv+0xfa3/0x1dc0 net/ipv6/ip6_input.c:191
...
icmp6_send / icmpv6_send is invoked for both rx and tx paths. In both
cases the dst->dev should be preferred for determining the L3 domain
if the dst has been set on the skb. Fallback to the skb->dev if it has
not. This covers the case reported here where icmp6_send is invoked on
Rx before the route lookup.
Fixes: 5d41ce29e ("net: icmp6_send should use dst dev to determine L3 domain")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of bug fixes in 'net' overlapping other changes in
'net-next-.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
icmp6_send is called in response to some event. The skb may not have
the device set (skb->dev is NULL), but it is expected to have a dst set.
Update icmp6_send to use the dst on the skb to determine L3 domain.
Fixes: ca254490c8dfd ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving an ICMPv4 message containing extensions as
defined in RFC 4884, and translating it to ICMPv6 at SIT
or GRE tunnel, we need some extra manipulation in order
to properly forward the extensions.
This patch only takes care of Time Exceeded messages as they
are the ones that typically carry information from various
routers in a fabric during a traceroute session.
It also avoids complex skb logic if the data_len is not
a multiple of 8.
RFC states :
The "original datagram" field MUST contain at least 128 octets.
If the original datagram did not contain 128 octets, the
"original datagram" field MUST be zero padded to 128 octets.
In practice routers use 128 bytes of original datagram, not more.
Initial translation was added in commit ca15a078bd90
("sit: generate icmpv6 error when receiving icmpv4 error")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better traceroute/mtr support for SIT and GRE tunnels,
we translate IPV4 ICMP ICMP_TIME_EXCEEDED to ICMPV6_TIME_EXCEED
We also have to translate the IPv4 source IP address of ICMP
message to IPv6 v4mapped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to use this helper from GRE as well, so this is
the time to move it in net/ipv6/icmp.c
Also add a @nhs parameter, since SIT and GRE have different
values for the header(s) to skip.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SIT or GRE tunnels might want to translate an IPV4 address
into a v4mapped one when translating ICMP to ICMPv6.
This patch adds the parameter to icmp6_send() but
does not change icmpv6_send() signature.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8dfd ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 ping socket error handler doesn't correctly convert the new 32 bit
mtu to host endianness before using.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 6d0bfe22611602f ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.
Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Responses for packets to unused ports are getting lost with L3 domains.
IPv4 has ip_send_unicast_reply for sending TCP responses which accounts
for L3 domains; update the IPv6 counterpart tcp_v6_send_response.
For icmp the L3 master check needs to be moved up in icmp6_send
to properly respond to UDP packets to a port with no listener.
Fixes: ca254490c8df ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the sendmsg function of UDP, raw, ICMP and l2tp sockets, we use local
variables like hlimits, tclass, opt and dontfrag and pass them to corresponding
functions like ip6_make_skb, ip6_append_data and xxx_push_pending_frames.
This is not a good practice and makes it hard to add new parameters.
This fix introduces a new struct ipcm6_cookie similar to ipcm_cookie in
ipv4 and include the above mentioned variables. And we only pass the
pointer to this structure to corresponding functions. This makes it easier
to add new parameters in the future and makes the function cleaner.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 ICMP stats are atomics anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename ICMP6_INC_STATS_BH() to __ICMP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.
Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.
Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.
ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.
__ip6_dst_store() and ip6_dst_store() share same implementation.
sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()
Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.
This is because ip6_dst_store() can be called from process context,
without any lock held.
As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()
Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Messages like "icmp6_send: no reply to icmp error" are close
to useless. Adding source and destination addresses to provide
some more clue.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As with IPv4 support for VRFs added to IPv6 stack by replacing hardcoded
table ids with possibly device specific ones and manipulating the oif in
the flowi6. The flow flags are used to skip oif compare in nexthop lookups
if the device is enslaved to a VRF via the L3 master device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds net argument to ipv6_stub_impl.ipv6_dst_lookup
for use cases where sk is not available (like mpls).
sk appears to be needed to get the namespace 'net' and is optional
otherwise. This patch series changes ipv6_stub_impl.ipv6_dst_lookup
to take net argument. sk remains optional.
All callers of ipv6_stub_impl.ipv6_dst_lookup have been modified
to pass net. I have modified them to use already available
'net' in the scope of the call. I can change them to
sock_net(sk) to avoid any unintended change in behaviour if sock
namespace is different. They dont seem to be from code inspection.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating a RTF_CACHE route, RTF_ANYCAST is set based on rt6i_dst.
Also, rt6i_gateway is always set to the nexthop while the nexthop
could be a gateway or the rt6i_dst.addr.
After removing the rt6i_dst and rt6i_src dependency in the last patch,
we also need to stop the caller from depending on rt6i_gateway and
RTF_ANYCAST.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the assumptions that the returned rt is always
a RTF_CACHE entry with the rt6i_dst and rt6i_src containing the
destination and source address. The dst and src can be recovered from
the calling site.
We may consider to rename (rt6i_dst, rt6i_src) to
(rt6i_key_dst, rt6i_key_src) later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x == NULL and sometimes as !x. !x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are too many brackets. Maybe only one bracket is enough.
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change has no functional impact and simply addresses some coding
style issues detected by checkpatch. Specifically this change
adjusts "if" statements which also include the assignment of a
variable.
No changes to the resultant object files result as determined by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If icmp_rcv() has successfully processed the incoming ICMP datagram, we
should use consume_skb() rather than kfree_skb() because a hit on the likes
of perf -e skb:kfree_skb is not called-for.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove trailing whitespace in tcp.h icmp.c syncookies.c
Signed-off-by: Kenjiro Nakayama <nakayamakenjiro@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason to emit a log message for these.
Based upon a suggestion from Hannes Frederic Sowa.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
|
|
Current ICMP rate limiting uses inetpeer cache, which is an RBL tree
protected by a lock, meaning that hosts can be stuck hard if all cpus
want to check ICMP limits.
When say a DNS or NTP server process is restarted, inetpeer tree grows
quick and machine comes to its knees.
iptables can not help because the bottleneck happens before ICMP
messages are even cooked and sent.
This patch adds a new global limitation, using a token bucket filter,
controlled by two new sysctl :
icmp_msgs_per_sec - INTEGER
Limit maximal number of ICMP packets sent per second from this host.
Only messages whose type matches icmp_ratemask are
controlled by this limit.
Default: 1000
icmp_msgs_burst - INTEGER
icmp_msgs_per_sec controls number of ICMP packets sent per second,
while icmp_msgs_burst controls the burst size of these packets.
Default: 50
Note that if we really want to send millions of ICMP messages per
second, we might extend idea and infra added in commit 04ca6973f7c1a
("ip: make IP identifiers less predictable") :
add a token bucket in the ip_idents hash and no longer rely on inetpeer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.
Both objdump and diff -w show no differences.
A number of items are addressed in this patch:
* Multiple spaces converted to tabs
* Spaces before tabs removed.
* Spaces in pointer typing cleansed (char *)foo etc.
* Remove space after sizeof
* Ensure spacing around comparators such as if statements.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When dealing with ICMPv[46] Error Message, function icmp_socket_deliver()
and icmpv6_notify() do some valid checks on packet's length, but then some
protocols check packet's length redaudantly. So remove those duplicated
statements, and increase counter ICMP_MIB_INERRORS/ICMP6_MIB_INERRORS in
function icmp_socket_deliver() and icmpv6_notify() respectively.
In addition, add missed counter in udp6/udplite6 when socket is NULL.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kernel-originated IP packets that have no user socket associated
with them (e.g., ICMP errors and echo replies, TCP RSTs, etc.)
are emitted with a mark of zero. Add a sysctl to make them have
the same mark as the packet they are replying to.
This allows an administrator that wishes to do so to use
mark-based routing, firewalling, etc. for these replies by
marking the original packets inbound.
Tested using user-mode linux:
- ICMP/ICMPv6 echo replies and errors.
- TCP RST packets (IPv4 and IPv6).
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use skb_checksum_validate to verify checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This replaces 6 identical code snippets with a call to a new
static inline function.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify
processing to workqueue") some counters are now updated in process context
and thus need to disable bh before doing so, otherwise deadlocks can
happen on 32-bit archs. Fabio Estevam noticed this while while mounting
a NFS volume on an ARM board.
As a compensation for missing this I looked after the other *_STATS_BH
and found three other calls which need updating:
1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling)
2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ...
(only in case of icmp protocol with raw sockets in error handling)
3) ping6_v6_sendmsg (error handling)
Fixes: c15b1ccadb323ea ("ipv6: move DAD and addrconf_verify processing to workqueue")
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch 446fab59333dea91e54688f033dd8d788d0486fb ("ipv6: enable anycast addresses
as source addresses in ICMPv6 error messages") causes an Oops when pinging a not
set up IPv6 peer on a sit tunnel.
The problem is that ipv6_anycast_destination() uses unconditionally skb_dst(skb),
which is NULL in this case.
The solution is to use instead the ipv6_chk_acast_addr_src() function.
Here are the steps to reproduce it:
modprobe sit
ip link add sit1 type sit remote 10.16.0.121 local 10.16.0.249
ip l s sit1 up
ip -6 a a dev sit1 2001:1234::123 remote 2001:1234::121
ping6 2001:1234::121
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Uses ipv6_anycast_destination() in icmp6_send().
Suggested-by: Bill Fink <billfink@mindspring.com>
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change move anycast_src_echo_reply sysctl with other ipv6 sysctls.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suggested-by: Simon Schneider <simon-schneider@gmx.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|