summaryrefslogtreecommitdiffstats
path: root/net/bluetooth
AgeCommit message (Collapse)Author
2008-12-23Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/ppp_generic.c
2008-12-18net: Fix module refcount leak in kernel_accept()Wei Yongjun
The kernel_accept() does not hold the module refcount of newsock->ops->owner, so we need __module_get(newsock->ops->owner) code after call kernel_accept() by hand. In sunrpc, the module refcount is missing to hold. So this cause kernel panic. Used following script to reproduct: while [ 1 ]; do mount -t nfs4 192.168.0.19:/ /mnt touch /mnt/file umount /mnt lsmod | grep ipv6 done This patch fixed the problem by add __module_get(newsock->ops->owner) to kernel_accept(). So we do not need to used __module_get(newsock->ops->owner) in every place when used kernel_accept(). Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-14bt/rfcomm/tty: join error pathsIlpo Järvinen
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bluetooth: Fix unused var warning properly in rfcomm_sock_ioctl().David S. Miller
As Stephen Rothwell points out, we don't want 'sock' here but rather we really do want 'sk'. This local var is protected by all sorts of bluetooth debugging kconfig vars, but BT_DBG() is just a straight pr_debug() call which is unconditional. pr_debug() evaluates it's args only if either DEBUG or CONFIG_DYNAMIC_PRINTK_DEBUG is defined. Solving this inside of the BT_DBG() macro is non-trivial since it's varargs. And these ifdefs are ugly. So, just mark this 'sk' thing __maybe_unused and kill the ifdefs. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09bluetooth: Fix rfcomm_sock_ioctl() build failure with debugging enabled.David S. Miller
It's 'sock' not 'sk'. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-30Bluetooth: Fix RFCOMM release oops when device is still in useMarcel Holtmann
It turns out that the following sequence of actions will reproduce the oops: 1. Create a new RFCOMM device (using RFCOMMCREATEDEV ioctl) 2. (Try to) open the device 3. Release the RFCOMM device (using RFCOMMRELEASEDEV ioctl) At this point, the "/dev/rfcomm*" device is still in use, but it is gone from the internal list, so the device id can be reused. 4. Create a new RFCOMM device with the same device id as before And now kobject will complain that the TTY already exists. (See http://lkml.org/lkml/2008/7/13/89 for a reproducible test-case.) This patch attempts to correct this by only removing the device from the internal list of devices at the final unregister stage, so that the id won't get reused until the device has been completely destructed. This should be safe as the RFCOMM_TTY_RELEASED bit will be set for the device and prevent the device from being reopened after it has been released. Based on a report from Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30Bluetooth: Fix format arguments warningMarcel Holtmann
Newer GCC versions are a little bit picky about how to deal with format arguments: net/bluetooth/hci_sysfs.c: In function ‘hci_register_sysfs’: net/bluetooth/hci_sysfs.c:418: warning: format not a string literal and no format arguments It is simple enough to fix and makes the compiler happy. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30Bluetooth: Enable per-module dynamic debug messagesMarcel Holtmann
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to allow debugging without having to recompile the kernel. This patch turns all BT_DBG() calls into pr_debug() to support dynamic debug messages. As a side effect all CONFIG_BT_*_DEBUG statements are now removed and some broken debug entries have been fixed. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30Bluetooth: Send HCI Reset command by default on device initializationMarcel Holtmann
The Bluetooth subsystem was not using the HCI Reset command when doing device initialization. The Bluetooth 1.0b specification was ambiguous on how the device firmware was suppose to handle it. Almost every device was triggering a transport reset at the same time. In case of USB this ended up in disconnects from the bus. All modern Bluetooth dongles handle this perfectly fine and a lot of them actually require that HCI Reset is sent. If not then they are either stuck in their HID Proxy mode or their internal structures for inquiry and paging are not correctly setup. To handle old and new devices smoothly the Bluetooth subsystem contains a quirk to force the HCI Reset on initialization. However maintaining such a quirk becomes more and more complicated. This patch turns the logic around and lets the old devices disable the HCI Reset command. The only device where the HCI_QUIRK_NO_RESET is still needed are the original Digianswer devices and dongles with an early CSR firmware. CSR reported that they fixed this for version 12 firmware. The last official release of version 11 firmware is build ID 115. The first version 12 candidate was build ID 117. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30Bluetooth: Fix warnings for bt_key_strings and bt_slock_key_stringsMarcel Holtmann
After adding proper lockdep annotations for Bluetooth protocols the case when lockdep is disabled produced two compiler warnings: net/bluetooth/af_bluetooth.c:60: warning: ‘bt_key_strings’ defined but not used net/bluetooth/af_bluetooth.c:71: warning: ‘bt_slock_key_strings’ defined but not used Fix both of them by adding a CONFIG_DEBUG_LOCK_ALLOC conditional around them and re-arranging the code a little bit. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30Bluetooth: Fix leak of uninitialized data to userspaceVegard Nossum
struct hci_dev_list_req { __u16 dev_num; struct hci_dev_req dev_req[0]; /* hci_dev_req structures */ }; sizeof(struct hci_dev_list_req) == 4, so the two bytes immediately following "dev_num" will never be initialized. When this structure is copied to userspace, these uninitialized bytes are leaked. Fix by using kzalloc() instead of kmalloc(). Found using kmemcheck. Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-25bluetooth: fix warning in net/bluetooth/rfcomm/sock.cIngo Molnar
fix this warning: net/bluetooth/rfcomm/sock.c: In function ‘rfcomm_sock_ioctl’: net/bluetooth/rfcomm/sock.c:795: warning: unused variable ‘sk’ perhaps BT_DEBUG() should be improved to do printf format checking instead of the #ifdef, but that looks quite intrusive: each bluetooth .c file undefines the macro. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-12netdevice: safe convert to netdev_priv() #part-4Wang Chen
We have some reasons to kill netdev->priv: 1. netdev->priv is equal to netdev_priv(). 2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously netdev_priv() is more flexible than netdev->priv. But we cann't kill netdev->priv, because so many drivers reference to it directly. This patch is a safe convert for netdev->priv to netdev_priv(netdev). Since all of the netdev->priv is only for read. But it is too big to be sent in one mail. I split it to 4 parts and make every part smaller than 100,000 bytes, which is max size allowed by vger. Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-10net: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers
Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03net/: Kill now superfluous ->last_rx stores.David S. Miller
The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely) ipv4: Add a missing rcu_assign_pointer() in routing cache. [netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit xen-netfront: Avoid unaligned accesses to IP header lmc: copy_*_user under spinlock [netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
2008-10-16net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)Johannes Berg
Some code here depends on CONFIG_KMOD to not try to load protocol modules or similar, replace by CONFIG_MODULES where more than just request_module depends on CONFIG_KMOD and and also use try_then_request_module in ebtables. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-14HID: move connect quirksJiri Slaby
Move connecting from usbhid to the hid layer and fix also hidp in that manner. This removes all the ignore/force hidinput/hiddev connecting quirks. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2008-10-14HID: move apple quirksJiri Slaby
Move them from the core code to a separate driver. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2008-10-14HID: move ignore quirksJiri Slaby
Move ignore quirks from usbhid-quirks into hid-core code. Also don't output warning when ENODEV is error code in usbhid and try ordinal input in hidp when that error is returned. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2008-10-14HID: hid, make parsing event drivenJiri Slaby
Next step for complete hid bus, this patch includes: - call parser either from probe or from hid-core if there is no probe. - add ll_driver structure and centralize some stuff there (open, close...) - split and merge usb_hid_configure and hid_probe into several functions to allow hooks/fixes between them Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2008-10-14HID: make a bus from hid codeJiri Slaby
Make a bus from hid core. This is the first step for converting all the quirks and separate almost-drivers into real drivers attached to this bus. It's implemented to change behaviour in very tiny manner, so that no driver needs to be changed this time. Also add generic drivers for both usb and bt into usbhid or hidp respectively which will bind all non-blacklisted device. Those blacklisted will be either grabbed by special drivers or by nobody if they are broken at the very rude base. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2008-09-12[Bluetooth] Fix regression from using default link policyMarcel Holtmann
To speed up the Simple Pairing connection setup, the support for the default link policy has been enabled. This is in contrast to settings the link policy on every connection setup. Using the default link policy is the preferred way since there is no need to dynamically change it for every connection. For backward compatibility reason and to support old userspace the HCISETLINKPOL ioctl has been switched over to using hci_request() to issue the HCI command for setting the default link policy instead of just storing it in the HCI device structure. However the hci_request() can only be issued when the device is brought up. If used on a device that is registered, but still down it will timeout and fail. This is problematic since the command is put on the TX queue and the Bluetooth core tries to submit it to hardware that is not ready yet. The timeout for these requests is 10 seconds and this causes a significant regression when setting up a new device. The userspace can perfectly handle a failure of the HCISETLINKPOL ioctl and will re-submit it later, but the 10 seconds delay causes a problem. So in case hci_request() is called on a device that is still down, just fail it with ENETDOWN to indicate what happens. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-09-09[Bluetooth] Reject L2CAP connections on an insecure ACL linkMarcel Holtmann
The Security Mode 4 of the Bluetooth 2.1 specification has strict authentication and encryption requirements. It is the initiators job to create a secure ACL link. However in case of malicious devices, the acceptor has to make sure that the ACL is encrypted before allowing any kind of L2CAP connection. The only exception here is the PSM 1 for the service discovery protocol, because that is allowed to run on an insecure ACL link. Previously it was enough to reject a L2CAP connection during the connection setup phase, but with Bluetooth 2.1 it is forbidden to do any L2CAP protocol exchange on an insecure link (except SDP). The new hci_conn_check_link_mode() function can be used to check the integrity of an ACL link. This functions also takes care of the cases where Security Mode 4 is disabled or one of the devices is based on an older specification. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-09-09[Bluetooth] Enforce correct authentication requirementsMarcel Holtmann
With the introduction of Security Mode 4 and Simple Pairing from the Bluetooth 2.1 specification it became mandatory that the initiator requires authentication and encryption before any L2CAP channel can be established. The only exception here is PSM 1 for the service discovery protocol (SDP). It is meant to be used without any encryption since it contains only public information. This is how Bluetooth 2.0 and before handle connections on PSM 1. For Bluetooth 2.1 devices the pairing procedure differentiates between no bonding, general bonding and dedicated bonding. The L2CAP layer wrongly uses always general bonding when creating new connections, but it should not do this for SDP connections. In this case the authentication requirement should be no bonding and the just-works model should be used, but in case of non-SDP connection it is required to use general bonding. If the new connection requires man-in-the-middle (MITM) protection, it also first wrongly creates an unauthenticated link key and then later on requests an upgrade to an authenticated link key to provide full MITM protection. With Simple Pairing the link key generation is an expensive operation (compared to Bluetooth 2.0 and before) and doing this twice during a connection setup causes a noticeable delay when establishing a new connection. This should be avoided to not regress from the expected Bluetooth 2.0 connection times. The authentication requirements are known up-front and so enforce them. To fulfill these requirements the hci_connect() function has been extended with an authentication requirement parameter that will be stored inside the connection information and can be retrieved by userspace at any time. This allows the correct IO capabilities exchange and results in the expected behavior. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-09-09[Bluetooth] Fix reference counting during ACL config stageMarcel Holtmann
The ACL config stage keeps holding a reference count on incoming connections when requesting the extended features. This results in keeping an ACL link up without any users. The problem here is that the Bluetooth specification doesn't define an ownership of the ACL link and thus it can happen that the implementation on the initiator side doesn't care about disconnecting unused links. In this case the acceptor needs to take care of this. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-18[Bluetooth] Consolidate maintainers informationMarcel Holtmann
The Bluetooth entries for the MAINTAINERS file are a little bit too much. Consolidate them into two entries. One for Bluetooth drivers and another one for the Bluetooth subsystem. Also the MODULE_AUTHOR should indicate the current maintainer of the module and actually not the original author. Fix all Bluetooth modules to provide current maintainer information. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-18[Bluetooth] Fix userspace breakage due missing class linksMarcel Holtmann
The Bluetooth adapters and connections are best presented via a class in sysfs. The removal of the links inside the Bluetooth class broke assumptions by userspace programs on how to find attached adapters. This patch creates adapters and connections as part of the Bluetooth class, but it uses different device types to distinguish them. The userspace programs can now easily navigate in the sysfs device tree. The unused platform device and bus have been removed to keep the code simple and clean. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-08-07[Bluetooth] Add parameters to control BNEP header compressionMarcel Holtmann
The Bluetooth qualification for PAN demands testing with BNEP header compression disabled. This is actually pretty stupid and the Linux implementation outsmarts the test system since it compresses whenever possible. So to pass qualification two need parameters have been added to control the compression of source and destination headers. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-21bluetooth: remove improper bluetooth class symlinks.Greg Kroah-Hartman
Don't create symlinks in a class to a device that is not owned by the class. If the bluetooth subsystem really wants to point to all of the devices it controls, it needs to create real devices, not fake symlinks. Cc: Maxim Krasnyansky <maxk@qualcomm.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits) iucv: Fix bad merging. net_sched: Add size table for qdiscs net_sched: Add accessor function for packet length for qdiscs net_sched: Add qdisc_enqueue wrapper highmem: Export totalhigh_pages. ipv6 mcast: Omit redundant address family checks in ip6_mc_source(). net: Use standard structures for generic socket address structures. ipv6 netns: Make several "global" sysctl variables namespace aware. netns: Use net_eq() to compare net-namespaces for optimization. ipv6: remove unused macros from net/ipv6.h ipv6: remove unused parameter from ip6_ra_control tcp: fix kernel panic with listening_get_next tcp: Remove redundant checks when setting eff_sacks tcp: options clean up tcp: Fix MD5 signatures for non-linear skbs sctp: Update sctp global memory limit allocations. sctp: remove unnecessary byteshifting, calculate directly in big-endian sctp: Allow only 1 listening socket with SO_REUSEADDR sctp: Do not leak memory on multiple listen() calls sctp: Support ipv6only AF_INET6 sockets. ...
2008-07-20tty: Ldisc revampAlan Cox
Move the line disciplines towards a conventional ->ops arrangement. For the moment the actual 'tty_ldisc' struct in the tty is kept as part of the tty struct but this can then be changed if it turns out that when it all settles down we want to refcount ldiscs separately to the tty. Pull the ldisc code out of /proc and put it with our ldisc code. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-19Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6
2008-07-14[Bluetooth] Allow security for outgoing L2CAP connectionsMarcel Holtmann
When requested the L2CAP layer will now enforce authentication and encryption on outgoing connections. The usefulness of this feature is kinda limited since it will not allow proper connection ownership tracking until the authentication procedure has been finished. This is a limitation of Bluetooth 2.0 and before and can only be fixed by using Simple Pairing. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Add option to disable eSCO connection creationMarcel Holtmann
It has been reported that some eSCO capable headsets are not able to connect properly. The real reason for this is unclear at the moment. So for easier testing add a module parameter to disable eSCO connection creation. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Signal user-space for HIDP and BNEP socket errorsMarcel Holtmann
When using the HIDP or BNEP kernel support, the user-space needs to know if the connection has been terminated for some reasons. Wake up the application if that happens. Otherwise kernel and user-space are no longer on the same page and weird behaviors can happen. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Move pending packets from RFCOMM socket to TTYMarcel Holtmann
When an incoming RFCOMM socket connection gets converted into a TTY, it can happen that packets are lost. This mainly happens with the Handsfree profile where the remote side starts sending data right away. The problem is that these packets are in the socket receive queue. So when creating the TTY make sure to copy all pending packets from the socket receive queue to a private queue inside the TTY. To make this actually work, the flow control on the newly created TTY will be disabled and only enabled again when the TTY is opened by an application. And right before that, the pending packets will be put into the TTY flip buffer. Signed-off-by: Denis Kenzior <denis.kenzior@trolltech.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Store remote modem status for RFCOMM TTYMarcel Holtmann
When switching a RFCOMM socket to a TTY, the remote modem status might be needed later. Currently it is lost since the original configuration is done via the socket interface. So store the modem status and reply it when the socket has been converted to a TTY. Signed-off-by: Denis Kenzior <denis.kenzior@trolltech.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Use non-canonical TTY by default for RFCOMMMarcel Holtmann
While the RFCOMM TTY emulation can act like a real serial port, in reality it is not used like this. So to not mess up stupid applications, use the non-canonical mode by default. Signed-off-by: Denis Kenzior <denis.kenzior@trolltech.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Update Bluetooth core version numberMarcel Holtmann
With all the Bluetooth 2.1 changes and the support for Simple Pairing, it is important to update the Bluetooth core version number. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Use a more unique bus name for connectionsMarcel Holtmann
When attaching Bluetooth low-level connections to the bus, the bus name is constructed from the remote address since at that time the connection handle is not assigned yet. This has worked so far, but also caused a lot of troubles. It is better to postpone the creation of the sysfs entry to the time when the connection actually has been established and then use its connection handle as unique identifier. This also fixes the case where two different adapters try to connect to the same remote device. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Add support for TIOCOUTQ and TIOCINQ ioctlsMarcel Holtmann
Almost every protocol family supports the TIOCOUTQ and TIOCINQ ioctls and even Bluetooth could make use of them. When implementing audio streaming and integration with GStreamer or PulseAudio they will allow a better timing and synchronization. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Add timestamp support to L2CAP, RFCOMM and SCOMarcel Holtmann
Enable the common timestamp functionality that the network subsystem provides for L2CAP, RFCOMM and SCO sockets. It is possible to either use SO_TIMESTAMP or the IOCTLs to retrieve the timestamp of the current packet. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Export details about authentication requirementsMarcel Holtmann
With the Simple Pairing support, the authentication requirements are an explicit setting during the bonding process. Track and enforce the requirements and allow higher layers like L2CAP and RFCOMM to increase them if needed. This patch introduces a new IOCTL that allows to query the current authentication requirements. It is also possible to detect Simple Pairing support in the kernel this way. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Initiate authentication during connection establishmentMarcel Holtmann
With Bluetooth 2.1 and Simple Pairing the requirement is that any new connection needs to be authenticated and that encryption has been switched on before allowing L2CAP to use it. So make sure that all the requirements are fulfilled and otherwise drop the connection with a minimal disconnect timeout of 10 milliseconds. This change only affects Bluetooth 2.1 devices and Simple Pairing needs to be enabled locally and in the remote host stack. The previous changes made sure that these information are discovered before any kind of authentication and encryption is triggered. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Use ACL config stage to retrieve remote featuresMarcel Holtmann
The Bluetooth technology introduces new features on a regular basis and for some of them it is important that the hardware on both sides support them. For features like Simple Pairing it is important that the host stacks on both sides have switched this feature on. To make valid decisions, a config stage during ACL link establishment has been introduced that retrieves remote features and if needed also the remote extended features (known as remote host features) before signalling this link as connected. This change introduces full reference counting of incoming and outgoing ACL links and the Bluetooth core will disconnect both if no owner of it is present. To better handle interoperability during the pairing phase the disconnect timeout for incoming connections has been increased to 10 seconds. This is five times more than for outgoing connections. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Export remote Simple Pairing mode via sysfsMarcel Holtmann
Since the remote Simple Pairing mode is stored together with the inquiry cache, it makes sense to show it together with the other information. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Track status of remote Simple Pairing modeMarcel Holtmann
The Simple Pairing process can only be used if both sides have the support enabled in the host stack. The current Bluetooth specification has three ways to detect this support. If an Extended Inquiry Result has been sent during inquiry then it is safe to assume that Simple Pairing is enabled. It is not allowed to enable Extended Inquiry without Simple Pairing. During the remote name request phase a notification with the remote host supported features will be sent to indicate Simple Pairing support. Also the second page of the remote extended features can indicate support for Simple Pairing. For all three cases the value of remote Simple Pairing mode is stored in the inquiry cache for later use. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Track status of Simple Pairing modeMarcel Holtmann
The Simple Pairing feature is optional and needs to be enabled by the host stack first. The Linux kernel relies on the Bluetooth daemon to either enable or disable it, but at any time it needs to know the current state of the Simple Pairing mode. So track any changes made by external entities and store the current mode in the HCI device structure. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-07-14[Bluetooth] Disable disconnect timer during Simple PairingMarcel Holtmann
During the Simple Pairing process the HCI disconnect timer must be disabled. The way to do this is by holding a reference count of the HCI connection. The Simple Pairing process on both sides starts with an IO Capabilities Request and ends with Simple Pairing Complete. Signed-off-by: Marcel Holtmann <marcel@holtmann.org>