Age | Commit message (Collapse) | Author |
|
The mesh interface can delay OGM messages to aggregate different ogms
together in a single OGM packet.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AGGREGATED_OGMS_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the VLANs on top of
the mesh/soft-interface have configuration settings. The genl interface
reflects this by allowing to get/set it using the vlan specific commands
BATADV_CMD_GET_VLAN/BATADV_CMD_SET_VLAN.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_VLAN command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the
slave/hard-interface have B.A.T.M.A.N. V specific configuration settings.
The genl interface reflects this by allowing to get/set it using the
hard-interface specific commands.
The BATADV_CMD_GET_HARDIFS (or short version BATADV_CMD_GET_HARDIF) is
reused as get command because it already allow sto dump the content of
other information from the slave/hard-interface which are not yet
configuration specific.
The set command BATADV_CMD_SET_HARDIF will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_HARDIF
command message type that settings might have been changed and what the
current values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
The main objects for this configuration is the mesh/soft-interface object.
Its actual object in memory already contains most of the available
configuration settings. The genl interface reflects this by allowing to
get/set it using the mesh specific commands.
The BATADV_CMD_GET_MESH_INFO (or short version BATADV_CMD_GET_MESH) is
reused as get command because it already provides the content of other
information from the mesh/soft-interface which are not yet configuration
specific.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_MESH command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit ff4c92d85c6f ("genetlink: introduce pre_doit/post_doit hooks")
intoduced a mechanism to run specific code for doit hooks before/after the
hooks are run. Since all doit hooks are requiring the batadv softif, it
should be retrieved/freed in these helpers to simplify the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
batadv_dat_put_dhcp is creating a new ARP packet via
batadv_dat_arp_create_reply and tries to forward it via
batadv_dat_send_data to different peers in the DHT. The original skb is not
consumed by batadv_dat_send_data and thus has to be consumed by the caller.
Fixes: b61ec31c8575 ("batman-adv: Snoop DHCPACKs for DAT")
Signed-off-by: Martin Weinelt <martin@linuxlounge.net>
[sven@narfation.org: add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Add DHCPACKs for DAT snooping, by Linus Luessing
- Update copyright years for 2019, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Avoid WARN to report incorrect configuration, by Sven Eckelmann
- Fix mac header position setting, by Sven Eckelmann
- Fix releasing station statistics, by Felix Fietkau
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the addition of TXQ stats in the per-tid statistics the struct
station_info grew significantly. This resulted in stack size warnings
due to the structure itself being above the limit for the warnings.
To work around this, the TID array was allocated dynamically. Also a
function to free this content was introduced with commit 7ea3e110f2f8
("cfg80211: release station info tidstats where needed") but the necessary
changes were not provided for batman-adv's B.A.T.M.A.N. V implementation.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8689c051a201 ("cfg80211: dynamically allocate per-tid stats for station info")
[sven@narfation.org: add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The caller of ndo_start_xmit may not already have called
skb_reset_mac_header. The returned value of skb_mac_header/eth_hdr
therefore can be in the wrong position and even outside the current skbuff.
This for example happens when the user binds to the device using a
PF_PACKET-SOCK_RAW with enabled qdisc-bypass:
int opt = 4;
setsockopt(sock, SOL_PACKET, PACKET_QDISC_BYPASS, &opt, sizeof(opt));
Since eth_hdr is used all over the codebase, the batadv_interface_tx
function must always take care of resetting it.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Reported-by: syzbot+9d7405c7faa390e60b4e@syzkaller.appspotmail.com
Reported-by: syzbot+7d20bc3f1ddddc0f9079@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
In a 1000 nodes mesh network (Freifunk Hamburg) we can still see
30KBit/s of ARP traffic (equalling about 25% of all layer two
specific overhead, remaining after some filtering) flooded through
the mesh. These 30KBit/s are mainly ARP Requests from the
gateways / DHCP servers.
By snooping DHCPACKs we can learn about MAC/IP address pairs
in the DHCP range without relying on ARP. This patch is in preparation
to eliminate the need for mesh wide message flooding for IPv4 address
resolution.
Also this allows to quickly update a MAC/IP pair at least in the DHT when
DHCP reassigns an IP address to a new host.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
It is not allowed to use WARN* helpers on potential incorrect input from
the user or transient problems because systems configured as panic_on_warn
will reboot due to such a problem.
A NULL return value of __dev_get_by_index can be caused by various problems
which can either be related to the system configuration or problems
(incorrectly returned network namespaces) in other (virtual) net_device
drivers. batman-adv should not cause a (harmful) WARN in this situation and
instead only report it via a simple message.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Reported-by: syzbot+c764de0fcfadca9a8595@syzkaller.appspotmail.com
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
|
|
Thanks to rigorous testing in wireless community mesh networks several
issues with multicast entries in the translation table were found and
fixed in the last 1.5 years. Now we see the first larger networks
(a few hundred nodes) with a batman-adv version with multicast
optimizations enabled arising, with no TT / multicast optimization
related issues so far.
Therefore it seems safe to enable multicast optimizations by default.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit ced72933a5e8 ("batman-adv: use CRC32C instead of CRC16 in TT
code") switched the translation table code from crc16 to crc32c. The
(optional) bridge loop avoidance code is the only user of this function.
batman-adv should only select CRC16 when it is actually using it.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Multiple datastructures use the hash helper functions to add and remove
entries from the simple hlist based hashes. These are often also dumped to
userspace via netlink and thus should have a generation sequence counter.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d14 ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The debug messages of batman-adv are not printed to the kernel log at all
but can be stored (depending on the compile setting) in the tracing buffer
or the batadv specific log buffer. There is also no debug module parameter
but a batadv netdev specific log_level setting to enable/disable different
classes of debug messages at runtime.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The BATMAN_ADV_DEBUGFS portion of batman-adv is marked as deprecated. Thus
all required functionality should be available without it. The debug log
was already modified to also output via the kernel tracing function but
still retained its BATMAN_ADV_DEBUGFS functionality.
Separate the entry point for the debug log from the debugfs portions to
make it possible to build with BATMAN_ADV_DEBUG and without
BATMAN_ADV_DEBUGFS.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batadv_dbg trace event uses different functionality and datastructures
which are not directly associated with the trace infrastructure. It should
not be expected that the trace headers indirectly provide them and instead
include the required headers directly.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit 00caf6a2b318 ("batman-adv: Mark debugfs functionality as
deprecated") introduced various messages to inform the user about the
deprecation of the debugfs based functionality. The messages also include
the context/task in which this problem was observed.
The datastructures and functions to access this information require special
headers. These should be included directly instead of depending on a more
complex and fragile include chain.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit dee222c7b20c ("batman-adv: Move OGM rebroadcast stats to
orig_ifinfo") removed all used functionality of the include linux/lockdep.h
from batadv_iv_ogm.c.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge")
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
Fixes: d6f94d91f766 ("batman-adv: ELP - adding basic infrastructure")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The batadv interfaces are virtual interfaces which just tunnel the traffic
over other ethernet compatible interfaces. It doesn't need serialization
during the tx phase and is using RCU for most of its internal
datastructures. Since it doesn't have actual queues which could be locked
independently, the throughput gets significantly reduced by the extra lock
in the core net code.
8 parallel TCP connections forwarded by an IPQ4019 based hardware over
5GHz could reach:
* without LLTX: 349 Mibit/s
* with LLTX: 563 Mibit/s
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
B.A.T.M.A.N. IV requires the number of rebroadcast from a neighboring
originator. These statistics are gathered per interface which transmitted
the OGM (and then received it again). Since an originator is not interface
specific, a resizable array was used in each originator.
This resizable array had an entry for each interface and had to be resizes
(for all OGMs) when the number of active interface was modified. This could
cause problems when a large number of interface is added and not enough
continuous memory is available to allocate the array.
There is already a per interface originator structure "batadv_orig_ifinfo"
which can be used to store this information.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
A private debug logging infrastructure is currently provided via
$debug_fs/batman_adv/*/log when CONFIG_BATMAN_ADV_DEBUG is enabled. This is
not well integrated in the rest of the tracing infrastructure of the
kernel.
Other components (like mac80211 or ath10k) allow to gather the debug
messages using generic trace events which are better integrated. This makes
it possible to interact with them using the existing userspace tools.
The tracepoint batadv:batadv_dbg will now be available when
CONFIG_BATMAN_ADV_DEBUG and CONFIG_BATMAN_ADV_TRACING is activated. The log
level mask is still used for filtering as usual.
A full system trace for offline parsing can be created (and read) using:
$ batctl ll all
$ trace-cmd record -e batadv:batadv_dbg
$ trace-cmd report
The same can also be done without recording to a file
$ batctl ll all
$ trace-cmd stream -e batadv:batadv_dbg
The trace infrastructure is especially helpful when tracing processes:
$ batctl ll all
$ ./tools/perf/perf trace --event "batadv:*" batctl p 10.204.32.1
0.000 batadv:batadv_dbg:batman_adv bat0 Parsing outgoing ARP REQUEST
0.045 batadv:batadv_dbg:batman_adv bat0 ARP MSG = [src: a2:64:14:53:f8:22-10.204.32.185 dst: 00:00:00:00:00:00-10.204.32.1]
0.067 batadv:batadv_dbg:batman_adv bat0 Entry updated: 10.204.32.185 a2:64:14:53:f8:22 (vid: -1)
0.099 batadv:batadv_dbg:batman_adv bat0 batadv_dat_select_candidates(): IP=10.204.32.1 hash(IP)=48902
0.757 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 0: selected fe:2c:91:68:29:2b addr=48977 dist=65460
1.178 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 1: selected fe:81:ab:c5:e3:03 addr=49181 dist=65256
1.809 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 2: selected 66:25:a7:48:37:fb addr=49328 dist=65109
1.828 batadv:batadv_dbg:batman_adv bat0 DHT_SEND for 10.204.32.1
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
CONFIG_BATMAN_ADV_DEBUGFS is disabled by default because debugfs is not
supported for batman-adv interfaces in any non-default netns. Any remaining
users of this interface should still be informed about the deprecation and
the generic netlink alternative.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The hardif_neigh refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The backbone_gw refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_tvlv_handler_register is responsible for adding new
tvlv_handler to the handler_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: ef26157747d4 ("batman-adv: tvlv - basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_tt_global_orig_entry_add is responsible for adding new
tt_orig_list_entry to the orig_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d657e621a0f5 ("batman-adv: add reference counting for type batadv_tt_orig_list_entry")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_softif_vlan_get is responsible for adding new
softif_vlan to the softif_vlan_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: 5d2c05b21337 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_nc_get_nc_node is responsible for adding new nc_nodes
to the in_coding_list and out_coding_list. It first checks whether the
entry already is in the list or not. If it is, then the creation of a new
entry is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d56b1705e28c ("batman-adv: network coding - detect coding nodes and remove these after timeout")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The function batadv_gw_node_add is responsible for adding new gw_node to
the gateway_list. It is expecting that the caller already checked that
there is not already an entry with the same key or not.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|