| Age | Commit message (Collapse) | Author |
|---|
|
The third argument of fuse_get_user_pages() "nbytesp" refers to the number of
bytes a caller asked to pack into fuse request. This value may be lesser
than capacity of fuse request or iov_iter. So fuse_get_user_pages() must
ensure that *nbytesp won't grow.
Now, when helper iov_iter_get_pages() performs all hard work of extracting
pages from iov_iter, it can be done by passing properly calculated
"maxsize" to the helper.
The other caller of iov_iter_get_pages() (dio_refill_pages()) doesn't need
this capability, so pass LONG_MAX as the maxsize argument here.
Fixes: c9c37e2e6378 ("fuse: switch to iov_iter_get_pages()")
Reported-by: Werner Baumann <werner.baumann@onlinehome.de>
Tested-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... instead of maximal size.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
New variant of iov_iter - ITER_BVEC in iter->type, backed with
bio_vec array instead of iovec one. Primitives taught to deal
with such beasts, __swap_write() switched to using that kind
of iov_iter.
Note that bio_vec is just a <page, offset, length> triple - there's
nothing block-specific about it. I've left the definition where it
was, but took it from under ifdef CONFIG_BLOCK.
Next target: ->splice_write()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
if we'd ended up in the end of a segment, jump to the
beginning of the next one (iov_offset = 0, iov++),
rather than having the next primitive deal with that.
Ought to be folded back...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
parallel to copy_page_to_iter(). pipe_write() switched to it (and became
->write_iter()).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
same as iov_iter_get_pages(), except that pages array is allocated
(kmalloc if possible, vmalloc if that fails) and left for caller to
free. Lustre and NFS ->direct_IO() switched to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
counts the pages covered by iov_iter, up to given limit.
do_block_direct_io() and fuse_iter_npages() switched to
it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
iov_iter_get_pages(iter, pages, maxsize, &start) grabs references pinning
the pages of up to maxsize of (contiguous) data from iter. Returns the
amount of memory grabbed or -error. In case of success, the requested
area begins at offset start in pages[0] and runs through pages[1], etc.
Less than requested amount might be returned - either because the contiguous
area in the beginning of iterator is smaller than requested, or because
the kernel failed to pin that many pages.
direct-io.c switched to using iov_iter_get_pages()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
For now, just use the same thing we pass to ->direct_IO() - it's all
iovec-based at the moment. Pass it explicitly to iov_iter_init() and
account for kvec vs. iovec in there, by the same kludge NFS ->direct_IO()
uses.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
returns the value aligned as badly as the worst remaining segment
in iov_iter is. Use instead of open-coded equivalents.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
all callers can use copy_page_from_iter() and it actually simplifies
them.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
