| Age | Commit message (Collapse) | Author |
|---|
|
Add the gate action to the flow action entry. Add the gate parameters to
the tc_setup_flow_action() queueing to the entries of flow_action_entry
array provide to the driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a ingress frame gate control flow action.
Tc gate action does the work like this:
Assume there is a gate allow specified ingress frames can be passed at
specific time slot, and be dropped at specific time slot. Tc filter
chooses the ingress frames, and tc gate action would specify what slot
does these frames can be passed to device and what time slot would be
dropped.
Tc gate action would provide an entry list to tell how much time gate
keep open and how much time gate keep state close. Gate action also
assign a start time to tell when the entry list start. Then driver would
repeat the gate entry list cyclically.
For the software simulation, gate action requires the user assign a time
clock type.
Below is the setting example in user space. Tc filter a stream source ip
address is 192.168.0.20 and gate action own two time slots. One is last
200ms gate open let frame pass another is last 100ms gate close let
frames dropped. When the ingress frames have reach total frames over
8000000 bytes, the excessive frames will be dropped in that 200000000ns
time slot.
> tc qdisc add dev eth0 ingress
> tc filter add dev eth0 parent ffff: protocol ip \
flower src_ip 192.168.0.20 \
action gate index 2 clockid CLOCK_TAI \
sched-entry open 200000000 -1 8000000 \
sched-entry close 100000000 -1 -1
> tc chain del dev eth0 ingress chain 0
"sched-entry" follow the name taprio style. Gate state is
"open"/"close". Follow with period nanosecond. Then next item is internal
priority value means which ingress queue should put. "-1" means
wildcard. The last value optional specifies the maximum number of
MSDU octets that are permitted to pass the gate during the specified
time interval.
Base-time is not set will be 0 as default, as result start time would
be ((N + 1) * cycletime) which is the minimal of future time.
Below example shows filtering a stream with destination mac address is
10:00:80:00:00:00 and ip type is ICMP, follow the action gate. The gate
action would run with one close time slot which means always keep close.
The time cycle is total 200000000ns. The base-time would calculate by:
1357000000000 + (N + 1) * cycletime
When the total value is the future time, it will be the start time.
The cycletime here would be 200000000ns for this case.
> tc filter add dev eth0 parent ffff: protocol ip \
flower skip_hw ip_proto icmp dst_mac 10:00:80:00:00:00 \
action gate index 12 base-time 1357000000000 \
sched-entry close 200000000 -1 -1 \
clockid CLOCK_TAI
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the behavior of TCP_LINGER2 about its limit. The
sysctl_tcp_fin_timeout used to be the limit of TCP_LINGER2 but now it's
only the default value. A new macro named TCP_FIN_TIMEOUT_MAX is added
as the limit of TCP_LINGER2, which is 2 minutes.
Since TCP_LINGER2 used sysctl_tcp_fin_timeout as the default value
and the limit in the past, the system administrator cannot set the
default value for most of sockets and let some sockets have a greater
timeout. It might be a mistake that let the sysctl to be the limit of
the TCP_LINGER2. Maybe we can add a new sysctl to set the max of
TCP_LINGER2, but FIN-WAIT-2 timeout is usually no need to be too long
and 2 minutes are legal considering TCP specs.
Changes in v3:
- Remove the new socket option and change the TCP_LINGER2 behavior so
that the timeout can be set to value between sysctl_tcp_fin_timeout
and 2 minutes.
Changes in v2:
- Add int overflow check for the new socket option.
Changes in v1:
- Add a new socket option to set timeout greater than
sysctl_tcp_fin_timeout.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not much to be done here:
- add SPDX header;
- adjust title markup;
- remove a tail whitespace;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This PHY has two PHY IDs depending on its mode. Adjust the mask so that
it includes both IDs.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Output PPS signal on FIPER2 (Fixed Period Interval Pulse) in default
which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add, and use in generic netlink, helpers to dump out a netlink
policy to userspace, including all the range validation data,
nested policies etc.
This lets userspace discover what the kernel understands.
For families/commands other than generic netlink, the helpers
need to be used directly in an appropriate command, or we can
add some infrastructure (a new netlink family) that those can
register their policies with for introspection. I'm not that
familiar with non-generic netlink, so that's left out for now.
The data exposed to userspace also includes min and max length
for binary/string data, I've done that instead of letting the
userspace tools figure out whether min/max is intended based
on the type so that we can extend this later in the kernel, we
might want to just use the range data for example.
Because of this, I opted to not directly expose the NLA_*
values, even if some of them are already exposed via BPF, as
with min/max length we don't need to have different types here
for NLA_BINARY/NLA_MIN_LEN/NLA_EXACT_LEN, we just make them
all NL_ATTR_TYPE_BINARY with min/max length optionally set.
Similarly, we don't really need NLA_MSECS, and perhaps can
remove it in the future - but not if we encode it into the
userspace API now. It gets mapped to NL_ATTR_TYPE_U64 here.
Note that the exposing here corresponds to the strict policy
interpretation, and NLA_UNSPEC items are omitted entirely.
To get those, change them to NLA_MIN_LEN which behaves in
exactly the same way, but is exposed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helpers to get the policy's signed/unsigned range
validation data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a validation type instead, so we can later expose
the NLA_* values to userspace for policy descriptions.
Some transformations were done with this spatch:
@@
identifier p;
expression X, L, A;
@@
struct nla_policy p[X] = {
[A] =
-{ .type = NLA_EXACT_LEN_WARN, .len = L },
+NLA_POLICY_EXACT_LEN_WARN(L),
...
};
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since NLA_MSECS is really equivalent to NLA_U64, allow
it to have range validation as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using a pointer to a struct indicating the min/max values,
extend the ability to do range validation for arbitrary
values. Small values in the s16 range can be kept in the
policy directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the netlink policy, we currently have a void *validation_data
that's pointing to different things:
* a u32 value for bitfield32,
* the netlink policy for nested/nested array
* the string for NLA_REJECT
Remove the pointer and place appropriate type-safe items in the
union instead.
While at it, completely dissolve the pointer for the bitfield32
case and just put the value there directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a sysctl to control hrtimer slack, default of 100 usec.
This gives the opportunity to reduce system overhead,
and help very short RTT flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 86de5921a3d5 ("tcp: defer SACK compression after DupThresh")
I added a TCP_FASTRETRANS_THRESH bias to tp->compressed_ack in order
to enable sack compression only after 3 dupacks.
Since we plan to relax this rule for flows that involve
stacks not requiring this old rule, this patch adds
a distinct tp->dup_ack_counter.
This means the TCP_FASTRETRANS_THRESH value is now used
in a single location that a future patch can adjust:
if (tp->dup_ack_counter < TCP_FASTRETRANS_THRESH) {
tp->dup_ack_counter++;
goto send_now;
}
This patch also introduces tcp_sack_compress_send_ack()
helper to ease following patch comprehension.
This patch refines LINUX_MIB_TCPACKCOMPRESSED to not
count the acks that we had to send if the timer expires
or tcp_sack_compress_send_ack() is sending an ack.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-04-30
1) Add release all pages support, From Eran.
to release all FW pages at once on driver unload, when supported by FW.
2) From Maxim and Tariq, Trivial Data path cleanup and code improvements
in preparation for their next features, TLS offload and TX performance
improvements
3) Multiple cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- add a document title;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not much to be done here:
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds ability to filter sockets based on cgroup v2 ID.
Such filter is helpful in ss utility for filtering sockets by
cgroup pathname.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds cgroup v2 ID to common inet diag message attributes.
Cgroup v2 ID is kernfs ID (ino or ino+gen). This attribute allows filter
inet diag output by cgroup ID obtained by name_to_handle_at() syscall.
When net_cls or net_prio cgroup is activated this ID is equal to 1 (root
cgroup ID) for newly created sockets.
Some notes about this ID:
1) gets initialized in socket() syscall
2) incoming socket gets ID from listening socket
(not during accept() syscall)
3) not changed when process get moved to another cgroup
4) can point to deleted cgroup (refcounting)
v2:
- use CONFIG_SOCK_CGROUP_DATA instead if CONFIG_CGROUPS
v3:
- fix attr size by using nla_total_size_64bit() (Eric Dumazet)
- more detailed commit message (Konstantin Khlebnikov)
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-By: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates for both net-next and rdma-next:
1) HW bits and definitions for TLS and IPsec offlaods
2) Release all pages capability bits
3) New command interface helpers and some code cleanup as a result
4) Move qp.c out of mlx5 core driver into mlx5_ib rdma driver
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for nf-next:
1) Add IPS_HW_OFFLOAD status bit, from Bodong Wang.
2) Remove 128-bit limit on the set element data area, rise it
to 64 bytes.
3) Report EOPNOTSUPP for unsupported NAT types and flags.
4) Set up nft_nat flags from the control plane path.
5) Add helper functions to set up the nf_nat_range2 structure.
6) Add netmap support for nft_nat.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new TX WQE field for Connect-X6DX trailer insertion support,
when set, the HW adds a trailer to the packet, the WQE trailer
association flags are used to set to HW the header which the
trailer belongs.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add a bit in HCA capabilities layout to indicate if release all pages is
supported.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add TLS RX offload related IFC hardware fields and enumerations.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add needed structure layouts and defines for pci sync for fw update
event. The downstream patches will include event handlers for this event
type.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add needed structure layouts and defines for MFRL (Management Firmware
Reset Level) register. This structure will be used for the firmware
upgrade and reset flow in the downstream patches.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The imm_inval_pkey field can hold four different types of data,
depends on the usage, the data could be one of the below:
- Immediate field of the received message
- Invalidate rkey
- Pkey of the packet
- Flow table metadata
Current implementation doesn't reflect the intended usage of the
field at usage time.
Reflect the different types by replace this field with a union,
modify code where this field is used to reflect its intended
usage.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The alignment value is part of the input structure, so use it and spare
extra memory allocation when is not needed.
Now, using the new ability when allocating icm for Direct-Rule
insertion.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add IPsec offload related IFC structs, layouts and enumerations.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add COPY type to modify_header action. IPsec feature is the first
feature that needs COPY steering action.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
|
|
This patch allows you to NAT the network address prefix onto another
network address prefix, a.k.a. netmapping.
Userspace must specify the NF_NAT_RANGE_NETMAP flag and the prefix
address through the NFTA_NAT_REG_ADDR_MIN and NFTA_NAT_REG_ADDR_MAX
netlink attributes.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
So far, the set elements could store up to 128-bits in the data area.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Extend switchdev API to add support for MRP. The HW is notified in
following cases:
SWITCHDEV_OBJ_ID_MRP: This is used when a MRP instance is added/removed
from the MRP ring.
SWITCHDEV_OBJ_ID_RING_ROLE_MRP: This is used when the role of the node
changes. The current supported roles are MRM and MRC.
SWITCHDEV_OBJ_ID_RING_TEST_MRP: This is used when to start/stop sending
MRP_Test frames on the mrp ring ports. This is called only on nodes that have
the role MRM. In case this fails then the SW will generate the frames.
SWITCHDEV_OBJ_ID_RING_STATE_STATE: This is used when the ring changes it states
to open or closed. This is required to notify HW because the MRP_Test frame
contains the field MRP_InState which contains this information.
SWITCHDEV_ATTR_ID_MRP_PORT_STATE: This is used when the port's state is
changed. It can be in blocking/forwarding mode.
SWITCHDEV_ATTR_ID_MRP_PORT_ROLE: This is used when port's role changes. The
roles of the port can be primary/secondary. This is required to notify HW
because the MRP_Test frame contains the field MRP_PortRole that contains this
information.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new port attribute, IFLA_BRPORT_MRP_RING_OPEN, which allows
to notify the userspace when the port lost the continuite of MRP frames.
This attribute is set by kernel whenever the SW or HW detects that the ring is
being open or closed.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To integrate MRP into the bridge, first the bridge needs to be aware of ports
that are part of an MRP ring and which rings are on the bridge.
Therefore extend bridge interface with the following:
- add new flag(BR_MPP_AWARE) to the net bridge ports, this bit will be
set when the port is added to an MRP instance. In this way it knows if
the frame was received on MRP ring port
- add new flag(BR_MRP_LOST_CONT) to the net bridge ports, this bit will be set
when the port lost the continuity of MRP Test frames.
- add a list of MRP instances
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new nested netlink attribute to configure the MRP. These attributes are used
by the userspace to add/delete/configure MRP instances and by the kernel to
notify the userspace when the MRP ring gets open/closed. MRP nested attribute
has the following attributes:
IFLA_BRIDGE_MRP_INSTANCE - the parameter type is br_mrp_instance which contains
the instance id, and the ifindex of the two ports. The ports can't be part of
multiple instances. This is used to create/delete MRP instances.
IFLA_BRIDGE_MRP_PORT_STATE - the parameter type is u32. Which can be forwarding,
blocking or disabled.
IFLA_BRIDGE_MRP_PORT_ROLE - the parameter type is br_mrp_port_role which
contains the instance id and the role. The role can be primary or secondary.
IFLA_BRIDGE_MRP_RING_STATE - the parameter type is br_mrp_ring_state which
contains the instance id and the state. The state can be open or closed.
IFLA_BRIDGE_MRP_RING_ROLE - the parameter type is br_mrp_ring_role which
contains the instance id and the ring role. The role can be MRM or MRC.
IFLA_BRIDGE_MRP_START_TEST - the parameter type is br_mrp_start_test which
contains the instance id, the interval at which to send the MRP_Test frames,
how many test frames can be missed before declaring the ring open and the
period which represent for how long to send the test frames.
Also add the file include/uapi/linux/mrp_bridge.h which defines all the types
used by MRP that are also needed by the userpace.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bit indicates that the conntrack entry is offloaded to hardware
flow table. nf_conntrack entry will be tagged with [HW_OFFLOAD] if
it's offload to hardware.
cat /proc/net/nf_conntrack
ipv4 2 tcp 6 \
src=1.1.1.17 dst=1.1.1.16 sport=56394 dport=5001 \
src=1.1.1.16 dst=1.1.1.17 sport=5001 dport=56394 [HW_OFFLOAD] \
mark=0 zone=0 use=3
Note that HW_OFFLOAD/OFFLOAD/ASSURED are mutually exclusive.
Changelog:
* V1->V2:
- Remove check of lastused from stats. It was meant for cases such
as removing driver module while traffic still running. Better to
handle such cases from garbage collector.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In MPTCP, the receive window is shared across all subflows, because it
refers to the mptcp-level sequence space.
MPTCP receivers already place incoming packets on the mptcp socket
receive queue and will charge it to the mptcp socket rcvbuf until
userspace consumes the data.
Update __tcp_select_window to use the occupancy of the parent/mptcp
socket instead of the subflow socket in case the tcp socket is part
of a logical mptcp connection.
This commit doesn't change choice of initial window for passive or active
connections.
While it would be possible to change those as well, this adds complexity
(especially when handling MP_JOIN requests). Furthermore, the MPTCP RFC
specifically says that a MPTCP sender 'MUST NOT use the RCV.WND field
of a TCP segment at the connection level if it does not also carry a DSS
option with a Data ACK field.'
SYN/SYNACK packets do not carry a DSS option with a Data ACK field.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simple overlapping changes to linux/vermagic.h
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixlet from Ingo Molnar:
"A single fix for a comment that may show up in DocBook output"
* tag 'timers-urgent-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
vdso/datapage: Use correct clock mode name in comment
|
|
Pull networking fixes from David Miller:
1) Fix memory leak in netfilter flowtable, from Roi Dayan.
2) Ref-count leaks in netrom and tipc, from Xiyu Yang.
3) Fix warning when mptcp socket is never accepted before close, from
Florian Westphal.
4) Missed locking in ovs_ct_exit(), from Tonghao Zhang.
5) Fix large delays during PTP synchornization in cxgb4, from Rahul
Lakkireddy.
6) team_mode_get() can hang, from Taehee Yoo.
7) Need to use kvzalloc() when allocating fw tracer in mlx5 driver,
from Niklas Schnelle.
8) Fix handling of bpf XADD on BTF memory, from Jann Horn.
9) Fix BPF_STX/BPF_B encoding in x86 bpf jit, from Luke Nelson.
10) Missing queue memory release in iwlwifi pcie code, from Johannes
Berg.
11) Fix NULL deref in macvlan device event, from Taehee Yoo.
12) Initialize lan87xx phy correctly, from Yuiko Oshino.
13) Fix looping between VRF and XFRM lookups, from David Ahern.
14) etf packet scheduler assumes all sockets are full sockets, which is
not necessarily true. From Eric Dumazet.
15) Fix mptcp data_fin handling in RX path, from Paolo Abeni.
16) fib_select_default() needs to handle nexthop objects, from David
Ahern.
17) Use GFP_ATOMIC under spinlock in mac80211_hwsim, from Wei Yongjun.
18) vxlan and geneve use wrong nlattr array, from Sabrina Dubroca.
19) Correct rx/tx stats in bcmgenet driver, from Doug Berger.
20) BPF_LDX zero-extension is encoded improperly in x86_32 bpf jit, fix
from Luke Nelson.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (100 commits)
selftests/bpf: Fix a couple of broken test_btf cases
tools/runqslower: Ensure own vmlinux.h is picked up first
bpf: Make bpf_link_fops static
bpftool: Respect the -d option in struct_ops cmd
selftests/bpf: Add test for freplace program with expected_attach_type
bpf: Propagate expected_attach_type when verifying freplace programs
bpf: Fix leak in LINK_UPDATE and enforce empty old_prog_fd
bpf, x86_32: Fix logic error in BPF_LDX zero-extension
bpf, x86_32: Fix clobbering of dst for BPF_JSET
bpf, x86_32: Fix incorrect encoding in BPF_LDX zero-extension
bpf: Fix reStructuredText markup
net: systemport: suppress warnings on failed Rx SKB allocations
net: bcmgenet: suppress warnings on failed Rx SKB allocations
macsec: avoid to set wrong mtu
mac80211: sta_info: Add lockdep condition for RCU list usage
mac80211: populate debugfs only after cfg80211 init
net: bcmgenet: correct per TX/RX ring statistics
net: meth: remove spurious copyright text
net: phy: bcm84881: clear settings on link down
chcr: Fix CPU hard lockup
...
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2020-04-24
The following pull-request contains BPF updates for your *net* tree.
We've added 17 non-merge commits during the last 5 day(s) which contain
a total of 19 files changed, 203 insertions(+), 85 deletions(-).
The main changes are:
1) link_update fix, from Andrii.
2) libbpf get_xdp_id fix, from David.
3) xadd verifier fix, from Jann.
4) x86-32 JIT fixes, from Luke and Wang.
5) test_btf fix, from Stanislav.
6) freplace verifier fix, from Toke.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch fixes:
$ scripts/bpf_helpers_doc.py > bpf-helpers.rst
$ rst2man bpf-helpers.rst > bpf-helpers.7
bpf-helpers.rst:1105: (WARNING/2) Inline strong start-string without end-string.
Signed-off-by: Jakub Wilk <jwilk@jwilk.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200422082324.2030-1-jwilk@jwilk.net
|
|
commit 877d1f6291f8 ("net: Set sk_txhash from a random number")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no callers in-tree anymore.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
we don't need genphy_no_soft_reset() any longer. Not setting
callback soft_reset results in a no-op now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the callback into the phylink_config structure, rather than
providing a callback to set this up.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
