Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes and an old API removal now that all users are
gone"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: tegra: Synchronize DMA before termination
i2c: tegra: Better handle case where CPU0 is busy for a long time
i2c: remove i2c_new_probed_device API
i2c: altera: use proper variable to hold errno
i2c: designware: platdrv: Remove DPM_FLAG_SMART_SUSPEND flag on BYT and CHT
|
|
Pull block fixes from Jens Axboe:
- Fix for a driver tag leak in error handling (John)
- Remove now defunct Kconfig selection from dasd (Stefan)
- blk-wbt trace fiexs (Tommi)
* tag 'block-5.7-2020-04-17' of git://git.kernel.dk/linux-block:
blk-wbt: Drop needless newlines from tracepoint format strings
blk-wbt: Use tracepoint_string() for wbt_step tracepoint string literals
s390/dasd: remove IOSCHED_DEADLINE from DASD Kconfig
blk-mq: Put driver tag in blk_mq_dispatch_rq_list() when no budget
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"One significant regression fix is for HD-audio buffer preallocation.
In 5.6 it was set to non-prompt for x86 and forced to 0, but this
turned out to be problematic for some applications, hence it gets
reverted. Distros would need to restore CONFIG_SND_HDA_PREALLOC_SIZE
value to the earlier values they've used in the past.
Other than that, we've received quite a few small fixes for HD-audio
and USB-audio. Most of them are for dealing with the broken TRX40
mobos and the runtime PM without HD-audio codecs"
* tag 'sound-5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: call runtime_allow() for all hda controllers
ALSA: hda: Allow setting preallocation again for x86
ALSA: hda: Explicitly permit using autosuspend if runtime PM is supported
ALSA: hda: Skip controller resume if not needed
ALSA: hda: Keep the controller initialization even if no codecs found
ALSA: hda: Release resources at error in delayed probe
ALSA: hda: Honor PM disablement in PM freeze and thaw_noirq ops
ALSA: hda: Don't release card at firmware loading error
ALSA: usb-audio: Check mapping at creating connector controls, too
ALSA: usb-audio: Don't create jack controls for PCM terminals
ALSA: usb-audio: Don't override ignore_ctl_error value from the map
ALSA: usb-audio: Filter error from connector kctl ops, too
ALSA: hda/realtek - Enable the headset mic on Asus FX505DT
ALSA: ctxfi: Remove unnecessary cast in kfree
|
|
Drop needless newlines from tracepoint format strings, they only add
empty lines to perf tracing output.
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
|
|
To rehash a previous explanation given in commit 1c44ce560b4d ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e36e ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All in-tree users have been converted to the new i2c_new_scanned_device
function, so remove this deprecated one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- a series from Tianyu Lan to fix crash reporting on Hyper-V
- three miscellaneous cleanup patches
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/Hyper-V: Report crash data in die() when panic_on_oops is set
x86/Hyper-V: Report crash register data when sysctl_record_panic_msg is not set
x86/Hyper-V: Report crash register data or kmsg before running crash kernel
x86/Hyper-V: Trigger crash enlightenment only once during system crash.
x86/Hyper-V: Free hv_panic_page when fail to register kmsg dump
x86/Hyper-V: Unload vmbus channel in hv panic callback
x86: hyperv: report value of misc_features
hv_debugfs: Make hv_debug_root static
hv: hyperv_vmbus.h: Replace zero-length array with flexible-array member
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few regressions and one fix for stable:
- revert fsync optimization
- fix lost i_size update
- fix a space accounting leak
- build fix, add back definition of a deprecated ioctl flag
- fix search condition for old roots in relocation"
* tag 'for-5.7-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: re-instantiate the removed BTRFS_SUBVOL_CREATE_ASYNC definition
btrfs: fix reclaim counter leak of space_info objects
btrfs: make full fsyncs always operate on the entire file again
btrfs: fix lost i_size update after cloning inline extent
btrfs: check commit root generation in should_ignore_root
|
|
Update missing kernel-doc annotations and fix of related warnings
at 'make htmldocs'.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://lore.kernel.org/r/20200408231013.28370-1-l.rubusch@gmail.com
[fix indentation, attribute references]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The HD-audio controller does system-suspend and resume operations by
directly calling its helpers __azx_runtime_suspend() and
__azx_runtime_resume(). However, in general, we don't have to resume
always the device fully at the system resume; typically, if a device
has been runtime-suspended, we can leave it to runtime resume.
Usually for achieving this, the driver would call
pm_runtime_force_suspend() and pm_runtime_force_resume() pairs in the
system suspend and resume ops. Unfortunately, this doesn't work for
the resume path in our case. For handling the jack detection at the
system resume, a child codec device may need the (literally) forcibly
resume even if it's been runtime-suspended, and for that, the
controller device must be also resumed even if it's been suspended.
This patch is an attempt to improve the situation. It replaces the
direct __azx_runtime_suspend()/_resume() calls with with
pm_runtime_force_suspend() and pm_runtime_force_resume() with a slight
trick as we've done for the codec side. More exactly:
- azx_has_pm_runtime() check is dropped from azx_runtime_suspend() and
azx_runtime_resume(), so that it can be properly executed from the
system-suspend/resume path
- The WAKEEN handling depends on the card's power state now; it's set
and cleared only for the runtime-suspend
- azx_resume() checks whether any codec may need the forcible resume
beforehand. If the forcible resume is required, it does temporary
PM refcount up/down for actually triggering the runtime resume.
- A new helper function, hda_codec_need_resume(), is introduced for
checking whether the codec needs a forcible runtime-resume, and the
existing code is rewritten with that.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207043
Link: https://lore.kernel.org/r/20200413082034.25166-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Three small fixes/updates for the locking core code:
- Plug a task struct reference leak in the percpu rswem
implementation.
- Document the refcount interaction with PID_MAX_LIMIT
- Improve the 'invalid wait context' data dump in lockdep so it
contains all information which is required to decode the problem"
* tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Improve 'invalid wait context' splat
locking/refcount: Document interaction with PID_MAX_LIMIT
locking/percpu-rwsem: Fix a task_struct refcount
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
|
|
When oops happens with panic_on_oops unset, the oops
thread is killed by die() and system continues to run.
In such case, guest should not report crash register
data to host since system still runs. Check panic_on_oops
and return directly in hyperv_report_panic() when the function
is called in the die() and panic_on_oops is unset. Fix it.
Fixes: 7ed4325a44ea ("Drivers: hv: vmbus: Make panic reporting to be more useful")
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20200406155331.2105-7-Tianyu.Lan@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Merge yet more updates from Andrew Morton:
- Almost all of the rest of MM (memcg, slab-generic, slab, pagealloc,
gup, hugetlb, pagemap, memremap)
- Various other things (hfs, ocfs2, kmod, misc, seqfile)
* akpm: (34 commits)
ipc/util.c: sysvipc_find_ipc() should increase position index
kernel/gcov/fs.c: gcov_seq_next() should increase position index
fs/seq_file.c: seq_read(): add info message about buggy .next functions
drivers/dma/tegra20-apb-dma.c: fix platform_get_irq.cocci warnings
change email address for Pali Rohár
selftests: kmod: test disabling module autoloading
selftests: kmod: fix handling test numbers above 9
docs: admin-guide: document the kernel.modprobe sysctl
fs/filesystems.c: downgrade user-reachable WARN_ONCE() to pr_warn_once()
kmod: make request_module() return an error when autoloading is disabled
mm/memremap: set caching mode for PCI P2PDMA memory to WC
mm/memory_hotplug: add pgprot_t to mhp_params
powerpc/mm: thread pgprot_t through create_section_mapping()
x86/mm: introduce __set_memory_prot()
x86/mm: thread pgprot_t through init_memory_mapping()
mm/memory_hotplug: rename mhp_restrictions to mhp_params
mm/memory_hotplug: drop the flags field from struct mhp_restrictions
mm/special: create generic fallbacks for pte_special() and pte_mkspecial()
mm/vma: introduce VM_ACCESS_FLAGS
mm/vma: define a default value for VM_DATA_DEFAULT_FLAGS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- two cleanups
- fix a boot regression introduced in this merge window
- fix wrong use of memory allocation flags
* tag 'for-linus-5.7-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: fix booting 32-bit pv guest
x86/xen: make xen_pvmmu_arch_setup() static
xen/blkfront: fix memory allocation flags in blkfront_setup_indirect()
xen: Use evtchn_type_t as a type for event channels
|
|
For security reasons I stopped using gmail account and kernel address is
now up-to-date alias to my personal address.
People periodically send me emails to address which they found in source
code of drivers, so this change reflects state where people can contact
me.
[ Added .mailmap entry as per Joe Perches - Linus ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200307104237.8199-1-pali@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
devm_memremap_pages() is currently used by the PCI P2PDMA code to create
struct page mappings for IO memory. At present, these mappings are
created with PAGE_KERNEL which implies setting the PAT bits to be WB.
However, on x86, an mtrr register will typically override this and force
the cache type to be UC-. In the case firmware doesn't set this
register it is effectively WB and will typically result in a machine
check exception when it's accessed.
Other arches are not currently likely to function correctly seeing they
don't have any MTRR registers to fall back on.
To solve this, provide a way to specify the pgprot value explicitly to
arch_add_memory().
Of the arches that support MEMORY_HOTPLUG: x86_64, and arm64 need a
simple change to pass the pgprot_t down to their respective functions
which set up the page tables. For x86_32, set the page tables
explicitly using _set_memory_prot() (seeing they are already mapped).
For ia64, s390 and sh, reject anything but PAGE_KERNEL settings -- this
should be fine, for now, seeing these architectures don't support
ZONE_DEVICE.
A check in __add_pages() is also added to ensure the pgprot parameter
was set for all arches.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Eric Badger <ebadger@gigaio.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200306170846.9333-7-logang@deltatee.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The mhp_restrictions struct really doesn't specify anything resembling a
restriction anymore so rename it to be mhp_params as it is a list of
extended parameters.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Eric Badger <ebadger@gigaio.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200306170846.9333-3-logang@deltatee.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "Allow setting caching mode in arch_add_memory() for
P2PDMA", v4.
Currently, the page tables created using memremap_pages() are always
created with the PAGE_KERNEL cacheing mode. However, the P2PDMA code is
creating pages for PCI BAR memory which should never be accessed through
the cache and instead use either WC or UC. This still works in most
cases, on x86, because the MTRR registers typically override the caching
settings in the page tables for all of the IO memory to be UC-.
However, this tends not to work so well on other arches or some rare x86
machines that have firmware which does not setup the MTRR registers in
this way.
Instead of this, this series proposes a change to arch_add_memory() to
take the pgprot required by the mapping which allows us to explicitly
set pagetable entries for P2PDMA memory to UC.
This changes is pretty routine for most of the arches: x86_64, arm64 and
powerpc simply need to thread the pgprot through to where the page
tables are setup. x86_32 unfortunately sets up the page tables at boot
so must use _set_memory_prot() to change their caching mode. ia64, s390
and sh don't appear to have an easy way to change the page tables so,
for now at least, we just return -EINVAL on such mappings and thus they
will not support P2PDMA memory until the work for this is done. This
should be fine as they don't yet support ZONE_DEVICE.
This patch (of 7):
This variable is not used anywhere and should therefore be removed from
the structure.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Badger <ebadger@gigaio.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Link: http://lkml.kernel.org/r/20200306170846.9333-2-logang@deltatee.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently there are many platforms that dont enable ARCH_HAS_PTE_SPECIAL
but required to define quite similar fallback stubs for special page
table entry helpers such as pte_special() and pte_mkspecial(), as they
get build in generic MM without a config check. This creates two
generic fallback stub definitions for these helpers, eliminating much
code duplication.
mips platform has a special case where pte_special() and pte_mkspecial()
visibility is wider than what ARCH_HAS_PTE_SPECIAL enablement requires.
This restricts those symbol visibility in order to avoid redefinitions
which is now exposed through this new generic stubs and subsequent build
failure. arm platform set_pte_at() definition needs to be moved into a
C file just to prevent a build failure.
[anshuman.khandual@arm.com: use defined(CONFIG_ARCH_HAS_PTE_SPECIAL) in mips per Thomas]
Link: http://lkml.kernel.org/r/1583851924-21603-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Guo Ren <guoren@kernel.org> [csky]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Stafford Horne <shorne@gmail.com> [openrisc]
Acked-by: Helge Deller <deller@gmx.de> [parisc]
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Sam Creasey <sammy@sammy.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: http://lkml.kernel.org/r/1583802551-15406-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are many places where all basic VMA access flags (read, write,
exec) are initialized or checked against as a group. One such example
is during page fault. Existing vma_is_accessible() wrapper already
creates the notion of VMA accessibility as a group access permissions.
Hence lets just create VM_ACCESS_FLAGS (VM_READ|VM_WRITE|VM_EXEC) which
will not only reduce code duplication but also extend the VMA
accessibility concept in general.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Springer <rspringer@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/1583391014-8170-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are many platforms with exact same value for VM_DATA_DEFAULT_FLAGS
This creates a default value for VM_DATA_DEFAULT_FLAGS in line with the
existing VM_STACK_DEFAULT_FLAGS. While here, also define some more
macros with standard VMA access flag combinations that are used
frequently across many platforms. Apart from simplification, this
reduces code duplication as well.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Link: http://lkml.kernel.org/r/1583391014-8170-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the ability to insert multiple pages at once to a user VM with lower
PTE spinlock operations.
The intention of this patch-set is to reduce atomic ops for tcp zerocopy
receives, which normally hits the same spinlock multiple times
consecutively.
[akpm@linux-foundation.org: pte_alloc() no longer takes the `addr' argument]
[arjunroy@google.com: add missing page_count() check to vm_insert_pages()]
Link: http://lkml.kernel.org/r/20200214005929.104481-1-arjunroy.kdev@gmail.com
[arjunroy@google.com: vm_insert_pages() checks if pte_index defined]
Link: http://lkml.kernel.org/r/20200228054714.204424-2-arjunroy.kdev@gmail.com
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20200128025958.43490-2-arjunroy.kdev@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 944d9fec8d7a ("hugetlb: add support for gigantic page allocation
at runtime") has added the run-time allocation of gigantic pages.
However it actually works only at early stages of the system loading,
when the majority of memory is free. After some time the memory gets
fragmented by non-movable pages, so the chances to find a contiguous 1GB
block are getting close to zero. Even dropping caches manually doesn't
help a lot.
At large scale rebooting servers in order to allocate gigantic hugepages
is quite expensive and complex. At the same time keeping some constant
percentage of memory in reserved hugepages even if the workload isn't
using it is a big waste: not all workloads can benefit from using 1 GB
pages.
The following solution can solve the problem:
1) On boot time a dedicated cma area* is reserved. The size is passed
as a kernel argument.
2) Run-time allocations of gigantic hugepages are performed using the
cma allocator and the dedicated cma area
In this case gigantic hugepages can be allocated successfully with a
high probability, however the memory isn't completely wasted if nobody
is using 1GB hugepages: it can be used for pagecache, anon memory, THPs,
etc.
* On a multi-node machine a per-node cma area is allocated on each node.
Following gigantic hugetlb allocation are using the first available
numa node if the mask isn't specified by a user.
Usage:
1) configure the kernel to allocate a cma area for hugetlb allocations:
pass hugetlb_cma=10G as a kernel argument
2) allocate hugetlb pages as usual, e.g.
echo 10 > /sys/kernel/mm/hugepages/hugepages-1048576kB/nr_hugepages
If the option isn't enabled or the allocation of the cma area failed,
the current behavior of the system is preserved.
x86 and arm-64 are covered by this patch, other architectures can be
trivially added later.
The patch contains clean-ups and fixes proposed and implemented by Aslan
Bakirov and Randy Dunlap. It also contains ideas and suggestions
proposed by Rik van Riel, Michal Hocko and Mike Kravetz. Thanks!
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Andreas Schaufler <andreas.schaufler@gmx.de>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@kernel.org>
Cc: Aslan Bakirov <aslan@fb.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Link: http://lkml.kernel.org/r/20200407163840.92263-3-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I've noticed that there is no interface exposed by CMA which would let
me to declare contigous memory on particular NUMA node.
This patchset adds the ability to try to allocate contiguous memory on a
specific node. It will fallback to other nodes if the specified one
doesn't work.
Implement a new method for declaring contigous memory on particular node
and keep cma_declare_contiguous() as a wrapper.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Aslan Bakirov <aslan@fb.com>
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@kernel.org>
Cc: Andreas Schaufler <andreas.schaufler@gmx.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Link: http://lkml.kernel.org/r/20200407163840.92263-2-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a typo at the cross-reference link, causing this warning:
include/linux/slab.h:11: WARNING: undefined label: memory-allocation (if the link has no caption the label must precede a section header)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Link: http://lkml.kernel.org/r/0aeac24235d356ebd935d11e147dcc6edbb6465c.1586359676.git.mchehab+huawei@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
printk_deferred(), similarly to printk_safe/printk_nmi, does not
immediately attempt to print a new message on the consoles, avoiding
calls into non-reentrant kernel paths, e.g. scheduler or timekeeping,
which potentially can deadlock the system.
Those printk() flavors, instead, rely on per-CPU flush irq_work to print
messages from safer contexts. For same reasons (recursive scheduler or
timekeeping calls) printk() uses per-CPU irq_work in order to wake up
user space syslog/kmsg readers.
However, only printk_safe/printk_nmi do make sure that per-CPU areas
have been initialised and that it's safe to modify per-CPU irq_work.
This means that, for instance, should printk_deferred() be invoked "too
early", that is before per-CPU areas are initialised, printk_deferred()
will perform illegal per-CPU access.
Lech Perczak [0] reports that after commit 1b710b1b10ef ("char/random:
silence a lockdep splat with printk()") user-space syslog/kmsg readers
are not able to read new kernel messages.
The reason is printk_deferred() being called too early (as was pointed
out by Petr and John).
Fix printk_deferred() and do not queue per-CPU irq_work before per-CPU
areas are initialized.
Link: https://lore.kernel.org/lkml/aa0732c6-5c4e-8a8b-a1c1-75ebe3dca05b@camlintechnologies.com/
Reported-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Jann Horn <jannh@google.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull proc fix from Eric Biederman:
"A brown paper bag slipped through my proc changes, and syzcaller
caught it when the code ended up in your tree.
I have opted to fix it the simplest cleanest way I know how, so there
is no reasonable chance for the bug to repeat"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use a dedicated lock in struct pid
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"There's quite a few changes this time around.
Most of these are fixes and cleanups, but there's also new chip
support for some drivers and a bit of rework"
* tag 'pwm/for-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (33 commits)
pwm: pca9685: Fix PWM/GPIO inter-operation
pwm: Make pwm_apply_state_debug() static
pwm: meson: Remove redundant assignment to variable fin_freq
pwm: jz4740: Allow selection of PWM channels 0 and 1
pwm: jz4740: Obtain regmap from parent node
pwm: jz4740: Improve algorithm of clock calculation
pwm: jz4740: Use clocks from TCU driver
pwm: sun4i: Remove redundant needs_delay
pwm: omap-dmtimer: Implement .apply callback
pwm: omap-dmtimer: Do not disable PWM before changing period/duty_cycle
pwm: omap-dmtimer: Fix PWM enabling sequence
pwm: omap-dmtimer: Update description for PWM OMAP DM timer
pwm: omap-dmtimer: Drop unused header file
pwm: renesas-tpu: Drop confusing registered message
pwm: renesas-tpu: Fix late Runtime PM enablement
pwm: rcar: Fix late Runtime PM enablement
dt-bindings: pwm: renesas-tpu: Document more R-Car Gen2 support
pwm: meson: Fix confusing indentation
pwm: pca9685: Use gpio core provided macro GPIO_LINE_DIRECTION_OUT
pwm: pca9685: Replace CONFIG_PM with __maybe_unused
...
|
|
Pull more drm fixes from Dave Airlie:
"As expected, more fixes did turn up in the latter part of the week.
The drm_local_map build regression fix is here, along with temporary
disabling of the hugepage work due to some amdgpu related crashes.
Otherwise it's just a bunch of i915, and amdgpu fixes.
legacy:
- fix drm_local_map.offset type
ttm:
- temporarily disable hugepages to debug amdgpu problems.
prime:
- fix sg extraction
amdgpu:
- Various Renoir fixes
- Fix gfx clockgating sequence on gfx10
- RAS fixes
- Avoid MST property creation after registration
- Various cursor/viewport fixes
- Fix a confusing log message about optional firmwares
i915:
- Flush all the reloc_gpu batch (Chris)
- Ignore readonly failures when updating relocs (Chris)
- Fill all the unused space in the GGTT (Chris)
- Return the right vswing table (Jose)
- Don't enable DDI IO power on a TypeC port in TBT mode for ICL+ (Imre)
analogix_dp:
- probe fix
virtio:
- oob fix in object create"
* tag 'drm-next-2020-04-10' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/ttm: Temporarily disable the huge_fault() callback
drm/bridge: analogix_dp: Split bind() into probe() and real bind()
drm/legacy: Fix type for drm_local_map.offset
drm/amdgpu/display: fix warning when compiling without debugfs
drm/amdgpu: unify fw_write_wait for new gfx9 asics
drm/amd/powerplay: error out on forcing clock setting not supported
drm/amdgpu: fix gfx hang during suspend with video playback (v2)
drm/amd/display: Check for null fclk voltage when parsing clock table
drm/amd/display: Acknowledge wm_optimized_required
drm/amd/display: Make cursor source translation adjustment optional
drm/amd/display: Calculate scaling ratios on every medium/full update
drm/amd/display: Program viewport when source pos changes for DCN20 hw seq
drm/amd/display: Fix incorrect cursor pos on scaled primary plane
drm/amd/display: change default pipe_split policy for DCN1
drm/amd/display: Translate cursor position by source rect
drm/amd/display: Update stream adjust in dc_stream_adjust_vmin_vmax
drm/amd/display: Avoid create MST prop after registration
drm/amdgpu/psp: dont warn on missing optional TA's
drm/amdgpu: update RAS related dmesg print
drm/amdgpu: resolve mGPU RAS query instability
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes gathered since the previous update.
ALSA core:
- Regression fix for OSS PCM emulation
ASoC:
- Trivial fixes in reg bit mask ops, DAPM, DPCM and topology
- Lots of fixes for Intel-based devices
- Minor fixes for AMD, STM32, Qualcomm, Realtek
Others:
- Fixes for the bugs in mixer handling in HD-audio and ice1724
drivers that were caught by the recent kctl validator
- New quirks for HD-audio and USB-audio
Also this contains a fix for EDD firmware fix, which slipped from
anyone's hands"
* tag 'sound-fix-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda: Add driver blacklist
ALSA: usb-audio: Add mixer workaround for TRX40 and co
ALSA: hda/realtek - Add quirk for MSI GL63
ALSA: ice1724: Fix invalid access for enumerated ctl items
ALSA: hda: Fix potential access overflow in beep helper
ASoC: cs4270: pull reset GPIO low then high
ALSA: hda/realtek - Add HP new mute led supported for ALC236
ALSA: hda/realtek - Add supported new mute Led for HP
ASoC: rt5645: Add platform-data for Medion E1239T
ASoC: Intel: bytcr_rt5640: Add quirk for MPMAN MPWIN895CL tablet
ASoC: stm32: sai: Add missing cleanup
ALSA: usb-audio: Add registration quirk for Kingston HyperX Cloud Alpha S
ASoC: Intel: atom: Fix uninitialized variable compiler warning
ASoC: Intel: atom: Check drv->lock is locked in sst_fill_and_send_cmd_unlocked
ASoC: Intel: atom: Take the drv->lock mutex before calling sst_send_slot_map()
ASoC: SOF: Turn "firmware boot complete" message into a dbg message
ALSA: usb-audio: Add Pioneer DJ DJM-250MK2 quirk
ALSA: pcm: oss: Fix regression by buffer overflow fix (again)
ALSA: pcm: oss: Fix regression by buffer overflow fix
edd: Use scnprintf() for avoiding potential buffer overflow
...
|
|
Pull block fixes from Jens Axboe:
"Here's a set of fixes that should go into this merge window. This
contains:
- NVMe pull request from Christoph with various fixes
- Better discard support for loop (Evan)
- Only call ->commit_rqs() if we have queued IO (Keith)
- blkcg offlining fixes (Tejun)
- fix (and fix the fix) for busy partitions"
* tag 'block-5.7-2020-04-10' of git://git.kernel.dk/linux-block:
block: fix busy device checking in blk_drop_partitions again
block: fix busy device checking in blk_drop_partitions
nvmet-rdma: fix double free of rdma queue
blk-mq: don't commit_rqs() if none were queued
nvme-fc: Revert "add module to ops template to allow module references"
nvme: fix deadlock caused by ANA update wrong locking
nvmet-rdma: fix bonding failover possible NULL deref
loop: Better discard support for block devices
loop: Report EOPNOTSUPP properly
nvmet: fix NULL dereference when removing a referral
nvme: inherit stable pages constraint in the mpath stack device
blkcg: don't offline parent blkcg first
blkcg: rename blkcg->cgwb_refcnt to ->online_pin and always use it
nvme-tcp: fix possible crash in recv error flow
nvme-tcp: don't poll a non-live queue
nvme-tcp: fix possible crash in write_zeroes processing
nvmet-fc: fix typo in comment
nvme-rdma: Replace comma with a semicolon
nvme-fcloop: fix deallocation of working context
nvme: fix compat address handling in several ioctls
|
|
The commit 9c1036fdb1d1ff1b ("btrfs: Remove BTRFS_SUBVOL_CREATE_ASYNC
support") breaks strace build with the kernel headers from git:
btrfs.c: In function "btrfs_test_subvol_ioctls":
btrfs.c:531:23: error: "BTRFS_SUBVOL_CREATE_ASYNC" undeclared (first use
in this function)
vol_args_v2.flags = BTRFS_SUBVOL_CREATE_ASYNC;
Moreover, it is improper to break UAPI, strace uses the definitions to
decode ioctls that are considered part of public API.
Restore the macro definition and put it under "#ifndef __KERNEL__"
in order to prevent inadvertent in-kernel usage.
Fixes: 9c1036fdb1d1ff1b ("btrfs: Remove BTRFS_SUBVOL_CREATE_ASYNC support")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains a handful of new features:
- Partial support for the Kendryte K210.
There are still a few outstanding issues that I have patches for,
but I don't actually have a board to test them so they're not
included yet.
- SBI v0.2 support.
- Fixes to support for building with LLVM-based toolchains. The
resulting images are known not to boot yet.
I don't anticipate a part two, but I'll probably have something early
in the RCs to finish up the K210 support"
* tag 'riscv-for-linus-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (38 commits)
riscv: create a loader.bin boot image for Kendryte SoC
riscv: Kendryte K210 default config
riscv: Add Kendryte K210 device tree
riscv: Select required drivers for Kendryte SOC
riscv: Add Kendryte K210 SoC support
riscv: Add SOC early init support
riscv: Unaligned load/store handling for M_MODE
RISC-V: Support cpu hotplug
RISC-V: Add supported for ordered booting method using HSM
RISC-V: Add SBI HSM extension definitions
RISC-V: Export SBI error to linux error mapping function
RISC-V: Add cpu_ops and modify default booting method
RISC-V: Move relocate and few other functions out of __init
RISC-V: Implement new SBI v0.2 extensions
RISC-V: Introduce a new config for SBI v0.1
RISC-V: Add SBI v0.2 extension definitions
RISC-V: Add basic support for SBI v0.2
RISC-V: Mark existing SBI as 0.1 SBI.
riscv: Use macro definition instead of magic number
riscv: Add support to dump the kernel page tables
...
|