| Age | Commit message (Collapse) | Author |
|---|
|
osc->cko2_sel->cko2_podf->clk_cko2->clk_cko
Example of usage to provide clock to the sgtl5000
codec: sgtl5000@0a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
clocks = <&clks IMX6UL_CLK_OSC>;
#sound-dai-cells = <0>;
clocks = <&clks IMX6UL_CLK_CKO>;
assigned-clocks = <&clks IMX6UL_CLK_CKO2_SEL>,
<&clks IMX6UL_CLK_CKO2_PODF>,
<&clks IMX6UL_CLK_CKO2>,
<&clks IMX6UL_CLK_CKO>;
assigned-clock-parents = <&clks IMX6UL_CLK_OSC>,
<&clks IMX6UL_CLK_CKO2_SEL>,
<&clks IMX6UL_CLK_CKO2_PODF>,
<&clks IMX6UL_CLK_CKO2>;
clock-names = "mclk";
wlf,shared-lrclk;
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Just add binding for a required reset referenced by Mali-450 on MT7623
or MT2701 SoC.
Cc: devicetree@vger.kernel.org
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Just add binding for a required clock referenced by Mali-450 on MT7623
or MT2701 SoC.
Cc: devicetree@vger.kernel.org
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The hdmitx_dig_cts clock signal is not a child of clk26m,
and the actual output of the PLL block is derived from
the tvdpll via a configurable PLL post-divider.
It is used as the PLL reference input to the HDMI PHY module.
Fixes: e9862118272a ("clk: mediatek: Add MT2701 clock support")
Signed-off-by: Chunhui Dai <chunhui.dai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
There are two USB3 host controllers on Hi3798CV200 SoC.
This commit adds missing clocks for them.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This commit fixes incorrect setting of reset bits for PCI/VGA and
PECI modules.
1. Reset bit for PCI/VGA is 8.
2. PECI reset bit is missing so added bit 10 as its reset bit.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Fixes: 15ed8ce5f84e ("clk: aspeed: Register gated clocks")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The ast2500 has an additional reset register that contains resets not
present in the ast2400. This enables support for this register, and adds
the one reset line that is controlled by it.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add dt-bindings headers for the Meson-AXG's AO clock and
reset controller.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add DT bindings for ASM (Audio Stream Manager) DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch add DT bindings for AFE (Audio Frontend) DSP module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-and-tested-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch add dt bindings for Qualcomm APR (Asynchronous Packet Router)
bus driver. This bus is used for communicating with DSP which provides
audio and various other services to cpu.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add devicetree-bindings for the dmic, jack-detect source and overcurrent-
detect threshold settings.
The dmic bindings mirror the existing bindings for the rt5645.
The jd-src and ovcd bindings mirror the existing bindings for the rt5651.
Cc devicetree@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add compatible string and the include file for gcc clock
controller for SDM845.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
i.MX6SX has lvds2 (analog clock2), an I/O clock like lvds1.
And this lvds2, along with lvds1, can be used to provide
external clock source to the internal pll, such as pll4_audio
and pll5_video.
This patch mainly adds the lvds2 to the clock tree and fix its
relationship with pll accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The H6 has clock/reset controls in PRCM part, like old SoCs such as H3
and A64. However, the PRCM CCU is rearranged; the register arragement
is now similar to the main CCU of H6, and the PRCM now has two APB
buses to control -- one is clocked from AHB clock derivde from AR100
clock, the other is clocked from the same mux with AR100 clock.
Therefore a new driver is written for it.
As there's no official document about the PRCM in H6, all the information
are indirectly collected from BSP and parts of the document, and the
information source is noted as comments in the driver's source code. If
reliable information is provided furtherly, the driver needs to be
rechecked.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add RPMh clock device bindings for Qualcomm Technology Inc's SoCs. These
devices would be used for communicating resource state requests to control
the clocks managed by RPMh.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the devicetree node to support the DMA controller found
in JZ480 SoCs.
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fulfill the pinmux macros for MT7623
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add definitions for the Tegra20+ memory controller hot resets.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Export video decoder clock dt-bindings
Signed-off-by: Maxime Jourdan <maxi.jourdan@wanadoo.fr>
[added commit description]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the NAND clock to the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
This patch adds all R-Car E3 Clock Pulse Generator Core Clock Outputs.
Note that internal CPG clocks (S0, S1, S2, S3, SDSRC, POST3) are not
included, as they are used as internal clock sources only, and never
referenced from DT.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Conflicts were simple overlapping changes in microchip
driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the global clock controller found on MSM8998
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Imran Khan <kimran@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Specify regs for alpha_plls, fix white spaces and add binding]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
* clk-stm32mp1:
clk: stm32mp1: remove ck_apb_dbg clock
clk: stm32mp1: set stgen_k clock as critical
clk: stm32mp1: add missing tzc2 clock
clk: stm32mp1: fix SAI3 & SAI4 clocks
clk: stm32mp1: remove unused dfsdm_src[] const
clk: stm32mp1: add missing static
|
|
This patch adds power domain indices for R-Car E3.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: add commit log and SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for RZ/G1C (R8A77470) SoC power areas to the R-Car SYSC
driver.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add all RZ/G1C Clock Pulse Generator Core Clock Outputs, as listed in
Table 7.2 ("List of Clocks [RZ/G1C]") of the RZ/G1C Hardware User's
Manual.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
[geert: Use consecutive numbering]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
|
|
It's recommended to use only clk_sys_dbg clock instead to activate
debug IP.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch adds tzc2 clock and rename tzc clock into tzc1
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
'clk-imx6sll' into clk-next
* clk-stratix10:
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
* clk-imx:
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: imx: pllv2: avoid using uninitialized values
clk: imx6ull: Add epdc_podf instead of sim_podf
clk: imx: imx7d: correct video pll clock tree
clk: imx: imx7d: add the Keypad Port module clock
clk: imx7d: add CAAM clock
clk: imx: imx7d: add the snvs clock
clk: imx: imx6sx: update cko mux options
* clk-bcm:
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
* clk-cs2000:
clk: cs2000: set pm_ops in hibernate-compatible way
* clk-imx6sll:
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
|
|
and 'clk-ti-flag-fix' into clk-next
* clk-davinci:
clk: davinci: Remove redundant dev_err calls
clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks
clk: davinci: New driver for TI DA8XX CFGCHIP clocks
dt-bindings: clock: Add bindings for DA8XX CFGCHIP clocks
clk: davinci: Add platform information for TI DM646x PSC
clk: davinci: Add platform information for TI DM644x PSC
clk: davinci: Add platform information for TI DM365 PSC
clk: davinci: Add platform information for TI DM355 PSC
clk: davinci: Add platform information for TI DA850 PSC
clk: davinci: Add platform information for TI DA830 PSC
clk: davinci: New driver for davinci PSC clocks
dt-bindings: clock: New bindings for TI Davinci PSC
clk: davinci: Add platform information for TI DM646x PLL
clk: davinci: Add platform information for TI DM644x PLL
clk: davinci: Add platform information for TI DM365 PLL
clk: davinci: Add platform information for TI DM355 PLL
clk: davinci: Add platform information for TI DA850 PLL
clk: davinci: Add platform information for TI DA830 PLL
clk: davinci: New driver for davinci PLL clocks
dt-bindings: clock: Add new bindings for TI Davinci PLL clocks
* clk-si544:
clk: Add driver for the si544 clock generator chip
* clk-rockchip:
clk: rockchip: assign correct id for pclk_ddr and hclk_sd in rk3399
clk: rockchip: Fix error return in phase clock registration
clk: rockchip: Correct the behaviour of restoring cached phase
clk: rockchip: Fix wrong parents for MMC phase clock for rk3328
clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228
clk: rockchip: Add 1.6GHz PLL rate for rk3399
clk: rockchip: Restore the clock phase after the rate was changed
clk: rockchip: Prevent calculating mmc phase if clock rate is zero
clk: rockchip: Free the memory on the error path
clk: rockchip: document hdmi_phy external input for rk3328
clk: rockchip: add flags for rk3328 dclk_lcdc
clk: rockchip: remove ignore_unused flag from rk3328 vio_h2p clocks
clk: rockchip: protect all remaining rk3328 interconnect clocks
clk: rockchip: export sclk_hdmi_sfc on rk3328
clk: rockchip: remove HCLK_VIO from rk3328 dt header
clk: rockchip: fix hclk_vio_niu on rk3328
* clk-uniphier:
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: uniphier: add ethernet clock control support for PXs3
clk: uniphier: add Pro4/Pro5/PXs2 audio system clock
* clk-ti-flag-fix:
clk: ti: fix flag space conflict with clkctrl clocks
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
|
|
'clk-renesas' into clk-next
* clk-mediatek:
clk: mediatek: add audsys support for MT2701
clk: mediatek: add devm_of_platform_populate() for MT7622 audsys
dt-bindings: clock: mediatek: add audsys support for MT2701
dt-bindings: clock: mediatek: update audsys documentation to adapt MFD device
clk: mediatek: update missing clock data for MT7622 audsys
clk: mediatek: fix PWM clock source by adding a fixed-factor clock
dt-bindings: clock: mediatek: add binding for fixed-factor clock axisel_d4
* clk-hisi:
clk: hisilicon: fix potential NULL dereference in hisi_clk_alloc()
clk: hisilicon: mark wdt_mux_p[] as const
clk: hisilicon: Mark phase_ops static
clk: hi3798cv200: add emmc sample and drive clock
clk: hisilicon: add hisi phase clock support
clk: hi3798cv200: add COMBPHY0 clock support
clk: hi3798cv200: fix define indentation
clk: hi3798cv200: add support for HISTB_USB2_OTG_UTMI_CLK
clk: hi3798cv200: correct IR clock parent
clk: hi3798cv200: fix unregister call sequence in error path
* clk-allwinner:
clk: sunxi-ng: add missing hdmi-slow clock for H6 CCU
clk: sunxi-ng: add support for the Allwinner H6 CCU
dt-bindings: add device tree binding for Allwinner H6 main CCU
clk: sunxi-ng: Support fixed post-dividers on NKMP style clocks
clk: sunxi-ng: h3: h5: export CLK_PLL_VIDEO
clk: sunxi-ng: h3: h5: Allow some clocks to set parent rate
clk: sunxi-ng: h3: h5: Add minimal rate for video PLL
clk: sunxi-ng: Add check for minimal rate to NM PLLs
clk: sunxi-ng: Use u64 for calculation of nkmp rate
clk: sunxi-ng: Mask nkmp factors when setting register
clk: sunxi-ng: remove select on obsolete SUNXI_CCU_X kconfig name
* clk-ux500:
clk: ux500: Drop AB8540/9540 support
* clk-renesas: (27 commits)
clk: renesas: cpg-mssr: Adjust r8a77980 ifdef
clk: renesas: rcar-gen3: Always use readl()/writel()
clk: renesas: sh73a0: Always use readl()/writel()
clk: renesas: rza1: Always use readl()/writel()
clk: renesas: rcar-gen2: Always use readl()/writel()
clk: renesas: r8a7740: Always use readl()/writel()
clk: renesas: r8a73a4: Always use readl()/writel()
clk: renesas: mstp: Always use readl()/writel()
clk: renesas: div6: Always use readl()/writel()
clk: fix false-positive Wmaybe-uninitialized warning
clk: renesas: r8a77965: Replace DU2 clock
clk: renesas: cpg-mssr: Add support for R-Car M3-N
clk: renesas: cpg-mssr: add R8A77980 support
dt-bindings: clock: add R8A77980 CPG core clock definitions
clk: renesas: r8a7792: Add rwdt clock
clk: renesas: r8a7794: Add rwdt clock
clk: renesas: r8a7791/r8a7793: Add rwdt clock
clk: renesas: r8a7790: Add rwdt clock
clk: renesas: r8a7745: Add rwdt clock
clk: renesas: r8a7743: Add rwdt clock
...
|
|
'clk-qcom-rpmcc' into clk-next
* clk-mvebu:
clk: mvebu: armada-38x: add support for missing clocks
clk: mvebu: cp110: Fix clock tree representation
* clk-phase:
clk: Don't show the incorrect clock phase
clk: update cached phase to respect the fact when setting phase
* clk-nxp:
clk: lpc32xx: Set name of regmap_config
* clk-mtk2712:
clk: mediatek: update clock driver of MT2712
dt-bindings: clock: add clocks for MT2712
* clk-qcom-rpmcc:
clk: qcom: rpmcc: Add support to XO buffered clocks
|
|
and 'clk-gpio' into clk-next
* clk-spreadtrum:
clk: sprd: add RTC gate for SC9860
dt-bindings: clocks: add APB RTC gate for SC9860
* clk-stm32f:
clk: stm32: Add clk entry for SDMMC2 on stm32F769
clk: stm32: Add DSI clock for STM32F469 Board
clk: stm32: END_PRIMARY_CLK should be declare after CLK_SYSCLK
* clk-stm32mp1:
clk: stm32: add configuration flags for each of the stm32 drivers
clk: stm32mp1: add Debug clocks
clk: stm32mp1: add MCO clocks
clk: stm32mp1: add RTC clock
clk: stm32mp1: add Peripheral & Kernel Clocks
clk: stm32mp1: add Kernel timers
clk: stm32mp1: add Sub System clocks
clk: stm32mp1: add Post-dividers for PLL
clk: stm32mp1: add PLL clocks
clk: stm32mp1: add Source Clocks for PLLs
clk: stm32mp1: add MP1 gate for hse/hsi/csi oscillators
clk: stm32mp1: Introduce STM32MP1 clock driver
dt-bindings: Document STM32MP1 Reset Clock Controller (RCC) bindings
* clk-hi655x:
clk: enable hi655x common clk automatically
* clk-gpio:
clk: clk-gpio: Allow GPIO to sleep in set/get_parent
|
|
clk-next
* clk-ti:
clk: keystone: sci-clk: add support for dynamically probing clocks
clk: ti: add support for clock latching to mux clocks
clk: ti: add support for clock latching to divider clocks
clk: ti: add generic support for clock latching
clk: ti: add support for register read-modify-write low-level operation
dt-bindings: clock: ti: add latching support to mux and divider clocks
* clk-amlogic: (50 commits)
clk: meson: Drop unused local variable and add static
clk: meson: clean-up clk81 clocks
clk: meson: add fdiv clock gates
clk: meson: add mpll pre-divider
clk: meson: axg: add hifi pll clock
clk: meson: axg: add hifi clock bindings
clk: meson: add ROUND_CLOSEST to the pll driver
clk: meson: add gp0 frac parameter for axg and gxl
clk: meson: improve pll driver results with frac
clk: meson: remove special gp0 lock loop
clk: meson: poke pll CNTL last
clk: meson: add fractional part of meson8b fixed_pll
clk: meson: use hhi syscon if available
clk: meson: remove obsolete cpu_clk
clk: meson: rework meson8b cpu clock
clk: meson: split divider and gate part of mpll
clk: meson: migrate plls clocks to clk_regmap
clk: meson: migrate the audio divider clock to clk_regmap
clk: meson: migrate mplls clocks to clk_regmap
clk: meson: add regmap helpers for parm
...
* clk-tegra:
clk: tegra: Fix pll_u rate configuration
clk: tegra: Specify VDE clock rate
clk: tegra20: Correct PLL_C_OUT1 setup
clk: tegra: Mark HCLK, SCLK and EMC as critical
clk: tegra: MBIST work around for Tegra210
clk: tegra: add fence_delay for clock registers
clk: tegra: Add la clock for Tegra210
* clk-samsung: (22 commits)
clk: samsung: Mark a few things static
clk: samsung: Add fout=196608001 Hz EPLL rate entry for exynos4412
clk: samsung: exynos5250: Add missing clocks for FIMC LITE SYSMMU devices
clk: samsung: exynos5420: Add more entries to EPLL rate table
clk: samsung: exynos5420: Add CLK_SET_RATE_PARENT flag to mout_mau_epll_clk
clk: samsung: exynos5250: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: exynos5420: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: Add Exynos5 sub-CMU clock driver
soc: samsung: pm_domains: Add blacklisting clock handling
clk: samsung: Add compile time PLL rate validators
clk: samsung: s3c2410: Fix PLL rates
clk: samsung: exynos7: Fix PLL rates
clk: samsung: exynos5433: Fix PLL rates
clk: samsung: exynos5260: Fix PLL rates
clk: samsung: exynos5250: Fix PLL rates
clk: samsung: exynos3250: Fix PLL rates
clk: exynos5433: Extend list of available AUD_PLL output frequencies
clk: exynos5433: Add CLK_IGNORE_UNUSED flag to sclk_ioclk_i2s1_bclk
clk: samsung: Add a git tree entry to MAINTAINERS
clk: samsung: Remove redundant dev_err call in exynos_audss_clk_probe()
...
|
|
Add clock binding doc update for imx6sll.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Document that Stratix10 clock bindings, and add the clock header file. The
clock header is an enumeration of all the different clocks on the Stratix10
platform.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes
and the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we
get two new machines based on its older siblings: the H5 based
OrangePi Zero+ and the A64 based Teres-I Laptop from Olimex. On the
32-bit side, we add The Olimex som204 based on Allwinner A20, and
the Banana Pi M2 Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6 family
of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones
Qualcomm msm8974 based Galaxy S5 is a rather different phone made
by the same company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre
Computer Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on
Rockchips RK3368 and made by Theobroma Systems"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (701 commits)
arm: dts: modify Nuvoton NPCM7xx device tree structure
arm: dts: modify Makefile NPCM750 configuration name
arm: dts: modify clock binding in NPCM750 device tree
arm: dts: modify timer register size in NPCM750 device tree
arm: dts: modify UART compatible name in NPCM750 device tree
arm: dts: add watchdog device to NPCM750 device tree
arm64: dts: uniphier: add ethernet node for PXs3
ARM: dts: uniphier: add pinctrl groups of ethernet for second instance
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for board using GPL-2.0+
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0+/MIT
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0
arm: dts: armada-385-turris-omnia: use SPDX-License-Identifier
arm: dts: armada-385-db-ap: use SPDX-License-Identifier
arm: dts: armada-388-rd: use SPDX-License-Identifier
arm: dts: armada-xp-db-xc3-24g4xg: use SPDX-License-Identifier
arm: dts: armada-xp-db-dxbc2: use SPDX-License-Identifier
arm: dts: armada-370-db: use SPDX-License-Identifier
arm: dts: armada-*.dts: use SPDX-License-Identifier for most of the Armada based board
arm: dts: armada-xp-98dx: use SPDX-License-Identifier for prestara 98d SoCs
arm: dts: armada-*.dtsi: use SPDX-License-Identifier for most of the Armada SoCs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- new driver for PhoenixRC Flight Controller Adapter
- new driver for RAVE SP Power button
- fixes for autosuspend-related deadlocks in a few unput USB dirvers
- support for 2nd wheel in ATech PS/2 mouse
- fix for ALPS trackpoint detection on Thinkpad L570 and Latitude 7370
- bunch of cleanups in various in PS/2 protocols
- other assorted changes and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: i8042 - enable MUX on Sony VAIO VGN-CS series to fix touchpad
Input: stmfts, s6sy761 - update my e-mail
Input: stmfts - use async probe & suspend/resume to avoid 2s delay
Input: ALPS - fix TrackStick detection on Thinkpad L570 and Latitude 7370
Input: xpad - add PDP device id 0x02a4
Input: alps - report pressure of v3 and v7 trackstick
Input: pxrc - new driver for PhoenixRC Flight Controller Adapter
Input: usbtouchscreen - do not rely on input_dev->users
Input: usbtouchscreen - fix deadlock in autosuspend
Input: pegasus_notetaker - do not rely on input_dev->users
Input: pagasus_notetaker - fix deadlock in autosuspend
Input: synaptics_usb - do not rely on input_dev->users
Input: synaptics_usb - fix deadlock in autosuspend
Input: gpio-keys - add support for wakeup event action
Input: appletouch - use true and false for boolean values
Input: silead - add Chuwi Hi8 support
Input: analog - use get_cycles() on PPC
Input: stmpe-keypad - remove VLA usage
Input: i8042 - add Lenovo ThinkPad L460 to i8042 reset list
Input: add RAVE SP Powerbutton driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became a large update. The changes are scattered widely, and the
majority of them are attributed to ASoC componentization. The gitk
output made me dizzy, but it's slightly better than London tube.
OK, below are some highlights:
- Continued hardening works in ALSA PCM core; most of the existing
syzkaller reports should have been covered.
- USB-audio got the initial USB Audio Class 3 support, as well as
UAC2 jack detection support and more DSD-device support.
- ASoC componentization: finally each individual driver was converted
to components framework, which is more future-proof for further
works. Most of conversations were systematic.
- Lots of fixes for Intel Baytrail / Cherrytrail devices with Realtek
codecs, typically tablets and small PCs.
- Fixes / cleanups for Samsung Odroid systems
- Cleanups in Freescale SSI driver
- New ASoC drivers:
* AKM AK4458 and AK5558 codecs
* A few AMD based machine drivers
* Intel Kabylake machine drivers
* Maxim MAX9759 codec
* Motorola CPCAP codec
* Socionext Uniphier SoCs
* TI PCM1789 and TDA7419 codecs
- Retirement of Blackfin drivers along with architecture removal"
* tag 'sound-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (497 commits)
ALSA: pcm: Fix UAF at PCM release via PCM timer access
ALSA: usb-audio: silence a static checker warning
ASoC: tscs42xx: Remove owner assignment from i2c_driver
ASoC: mediatek: remove "simple-mfd" in the example
ASoC: cpcap: replace codec to component
ASoC: Intel: bytcr_rt5651: don't use codec anymore
ASoC: amd: don't use codec anymore
ALSA: usb-audio: fix memory leak on cval
ALSA: pcm: Fix mutex unbalance in OSS emulation ioctls
ASoC: topology: Fix kcontrol name string handling
ALSA: aloop: Mark paused device as inactive
ALSA: usb-audio: update clock valid control
ALSA: usb-audio: UAC2 jack detection
ALSA: pcm: Return -EBUSY for OSS ioctls changing busy streams
ALSA: pcm: Avoid potential races between OSS ioctls and read/write
ALSA: usb-audio: Integrate native DSD support for ITF-USB based DACs.
ALSA: usb-audio: FIX native DSD support for TEAC UD-501 DAC
ALSA: usb-audio: Add native DSD support for Luxman DA-06
ALSA: usb-audio: fix uac control query argument
ASoC: nau8824: recover system clock when device changes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CEC pin injection code for testing purposes
- DVB frontend cxd2099 promoted from staging
- new platform driver for Sony cxd2880 DVB devices
- new sensor drivers: mt9t112, ov2685, ov5695, ov772x, tda1997x,
tw9910.c
- removal of unused cx18 and ivtv alsa mixers
- the reneseas-ceu driver doesn't depend on soc_camera anymore and
moved from staging
- removed the mantis_vp3028 driver, unused since 2009
- s5p-mfc: add support for version 10 of the MSP
- added a decoder for imon protocol
- atomisp: lots of cleanups
- imx074 and mt9t031: don't depend on soc_camera anymore, being
promoted from staging
- added helper functions to better support DVB I2C binding
- lots of driver improvements and cleanups
* tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (438 commits)
media: v4l2-ioctl: rename a temp var that stores _IOC_SIZE(cmd)
media: fimc-capture: get rid of two warnings
media: dvb-usb-v2: fix a missing dependency of I2C_MUX
media: uvc: to the right check at uvc_ioctl_enum_framesizes()
media: cec-core: fix a bug at cec_error_inj_write()
media: tda9840: cleanup a warning
media: tm6000: avoid casting just to print pointer address
media: em28xx-input: improve error handling code
media: zr364xx: avoid casting just to print pointer address
media: vivid-radio-rx: add a cast to avoid a warning
media: saa7134-alsa: don't use casts to print a buffer address
media: solo6x10: get rid of an address space warning
media: zoran: don't cast pointers to print them
media: ir-kbd-i2c: change the if logic to avoid a warning
media: ir-kbd-i2c: improve error handling code
media: saa7134-input: improve error handling
media: s2255drv: fix a casting warning
media: ivtvfb: Cleanup some warnings
media: videobuf-dma-sg: Fix a weird cast
soc_camera: fix a weird cast on printk
...
|
|
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spin |
