| Age | Commit message (Collapse) | Author |
|---|
|
Add support for the Texas Instruments INA219 and INA226 power monitors.
Signed-off-by: Lothar Felten <l-felten@ti.com>
[guenter.roeck@ericsson.com: formatting cleanup; check for smbus word data;
select PGA=8 for INA219]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
On IT8782F and IT8783F, some voltage input pins may be disabled. Don't create
sysfs attribute files if that is the case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Fix checkpatch WARNING: quoted string split across lines
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
The following build warning is seen in some configurations:
drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp':
drivers/hwmon/ntc_thermistor.c:293: warning: 'temp' may be used uninitialized in this function
Fix the problem by re-arranging the code to overload return values with error
codes, and by avoiding error returns whenever possible.
Specifically,
Simplify lookup_comp() to not return an error. Instead, return i_low == i_high
if there is an exact match, or if the ohm value is outside the lookup table
range.
Modify get_temp_mC() to not return an error. Since it only returns an error
after lookup_comp() returned an error, this is quite straightforward after above
change.
Separate ntc_thermistor_read() into a function to read the resistor value (which
can return an error), and the call to get_temp_mC() which doesn't. Call the
functions directly from ntc_show_temp().
Code was tested using a test program, comparing the result of the old and new
versions of get_temp_mC() for resistor values between 0 and 2,000,000 ohm.
As a side effect, this patch reduces code size by approximately 400 bytes on
x86_64.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
hwmon_device_register() never returns a NULL pointer in case of errors, but
an error value. Use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
This avoids memory leaks, and makes the code a bit simpler and smaller.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Remove unused defines AD7314_PD, AD7314_TEMP_SIGN, and ADT7301_TEMP_SIGN.
Rename AD7314_TEMP_OFFSET to the more appropriate AD7314_TEMP_SHIFT.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
We don't need to duplicate if (res) checks if we're always running
one or the other.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
We always register these two together, so move meter_rw_attrs into
meter_ro_attrs and use the same for both since we no longer have two
register_attr paths.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Key off the attr->set method being present to set the sysfs attribute
as writable.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Similar to how we do PCI/USB device id structs.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
We don't need both, when we can just key the read/write off of the
presence of the .set member.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
This patch converts the drivers in drivers/hwmon/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Pull block layer fixes from Jens Axboe:
"A few small, but important fixes. Most of them are marked for stable
as well
- Fix failure to release a semaphore on error path in mtip32xx.
- Fix crashable condition in bio_get_nr_vecs().
- Don't mark end-of-disk buffers as mapped, limit it to i_size.
- Fix for build problem with CONFIG_BLOCK=n on arm at least.
- Fix for a buffer overlow on UUID partition printing.
- Trivial removal of unused variables in dac960."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix buffer overflow when printing partition UUIDs
Fix blkdev.h build errors when BLOCK=n
bio allocation failure due to bio_get_nr_vecs()
block: don't mark buffers beyond end of disk as mapped
mtip32xx: release the semaphore on an error path
dac960: Remove unused variables from DAC960_CreateProcEntries()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull a dm fix from Alasdair G Kergon:
"A fix to the thin provisioning userspace interface."
* tag 'dm-3.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: fix table output when pool target disables discard passdown internally
|
|
When the thin pool target clears the discard_passdown parameter
internally, it incorrectly changes the table line reported to userspace.
This breaks dumb string comparisons on these table lines in generic
userspace device-mapper library code and leads to tables being reloaded
repeatedly when nothing is actually meant to be changing.
This patch corrects this by no longer changing the table line when
discard passdown was disabled.
We can still tell when discard passdown is overridden by looking for the
message "Discard unsupported by data device (sdX): Disabling discard passdown."
This automatic detection is also moved from the 'load' to the 'resume'
so that it is re-evaluated should the properties of underlying devices
change.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Pull one more md bugfix from NeilBrown:
"Fix bug in recent fix to RAID10.
Without this patch, recovery will crash"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/raid10: fix transcription error in calc_sectors conversion.
|
|
The old code was
sector_div(stride, fc);
the new code was
sector_dir(size, conf->near_copies);
'size' is right (the stride various wasn't really needed), but
'fc' means 'far_copies', and that is an important difference.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Merge misc fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (4 patches)
frv: delete incorrect task prototypes causing compile fail
slub: missing test for partial pages flush work in flush_all()
fs, proc: fix ABBA deadlock in case of execution attempt of map_files/ entries
drivers/rtc/rtc-pl031.c: configure correct wday for 2000-01-01
|
|
The reset date of the ST Micro version of PL031 is 2000-01-01. The
correct weekday for 2000-01-01 is saturday, but pl031 is initialized to
sunday. This may lead to alarm malfunction, so configure the correct
wday if RTC_DR indicates reset.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull two networking fixes from David S. Miller:
1) Thanks to Willy Tarreau and Eric Dumazet, we've unlocked a bug that's
been present in do_tcp_sendpages() since that function was written in
2002.
When we block to wait for memory we have to unconditionally try and
push out pending TCP data, otherwise we can block for an unreasonably
long amount of time.
2) Fix deadlock in e1000, fixes kernel bugzilla 43132
From Tushar Dave.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
e1000: Prevent reset task killing itself.
tcp: do_tcp_sendpages() must try to push data out on oom conditions
|
|
Commit 1cc0c998fdf2 ("ACPI: Fix D3hot v D3cold confusion") introduced a
bug in __acpi_bus_set_power() and changed the behavior of
acpi_pci_set_power_state() in such a way that it generally doesn't work
as expected if PCI_D3hot is passed to it as the second argument.
First off, if ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) is passed to
__acpi_bus_set_power() and the explicit_set flag is set for the D3cold
state, the function will try to execute AML method called "_PS4", which
doesn't exist.
Fix this by adding a check to ensure that the name of the AML method
to execute for transitions to ACPI_STATE_D3_COLD is correct in
__acpi_bus_set_power(). Also make sure that the explicit_set flag
for ACPI_STATE_D3_COLD will be set if _PS3 is present and modify
acpi_power_transition() to avoid accessing power resources for
ACPI_STATE_D3_COLD, because they don't exist.
Second, if PCI_D3hot is passed to acpi_pci_set_power_state() as the
target state, the function will request a transition to
ACPI_STATE_D3_HOT instead of ACPI_STATE_D3. However,
ACPI_STATE_D3_HOT is now only marked as supported if the _PR3 AML
method is defined for the given device, which is rare. This causes
problems to happen on systems where devices were successfully put
into ACPI D3 by pci_set_power_state(PCI_D3hot) which doesn't work
now. In particular, some unused graphics adapters are not turned
off as a result.
To fix this issue restore the old behavior of
acpi_pci_set_power_state(), which is to request a transition to
ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) if either PCI_D3hot or
PCI_D3cold is passed to it as the argument.
This approach is not ideal, because generally power should not
be removed from devices if PCI_D3hot is the target power state,
but since this behavior is relied on, we have no choice but to
restore it at the moment and spend more time on designing a
better solution in the future.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43228
Reported-by: rocko <rockorequin@hotmail.com>
Reported-by: Cristian Rodríguez <crrodriguez@opensuse.org>
Reported-and-tested-by: Peter <lekensteyn@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Killing reset task while adapter is resetting causes deadlock.
Only kill reset task if adapter is not resetting.
Ref bug #43132 on bugzilla.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull two more target-core updates from Nicholas Bellinger:
"The first patch addresses a SPC-2 reservations RELEASE bug in a
special (iscsi specific) multi-ISID setup case that was allowing the
same initiator to be able to incorrect release it's own reservation on
a different SCSI path with enforce_pr_isid=1 operation. This bug was
caught by Bernhard Kohl.
The second patch is to address a bug with FILEIO backends where the
incorrect number of blocks for READ_CAPACITY was being reported after
an underlying device-mapper block_device size change. This patch uses
now i_size_read() in fd_get_blocks() for FILEIO backends with an
underlying block_device, instead of trying to determine this value at
setup time during fd_create_virtdevice(). (hch CC'ed)
Both are CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix bug in handling of FILEIO + block_device resize ops
target: Fix SPC-2 RELEASE bug for multi-session iSCSI client setups
|
|
This patch fixes a bug in the handling of FILEIO w/ underlying block_device
resize operations where the original fd_dev->fd_dev_size was incorrectly being
used in fd_get_blocks() for READ_CAPACITY response payloads.
This patch avoids using fd_dev->fd_dev_size for FILEIO devices with
an underlying block_device, and instead changes fd_get_blocks() to
get the sector count directly from i_size_read() as recommended by hch.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pull slave-dmaengine fixes fromVinod Koul:
"fixes of cylic dma usages in slave dma drivers"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: fix cyclic dma usage
dmaengine: pl330: dont complete descriptor for cyclic dma
|
|
Pull last minute virtio fixes from Michael S. Tsirkin:
"Here are a couple of last minute virtio fixes for 3.4. Hope it's not
too late yes - I might have tried too hard to make sure the fix is
well tested.
Fixes are by Amit and myself. One fixes module removal and one
suspend of a VM, the last one the handling of out of memory condition.
They are thus very low risk as most people never hit these paths, but
do fix very annoying problems for people that do use the feature.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: invoke softirqs after __napi_schedule
virtio: balloon: let host know of updated balloon size before module removal
virtio: console: tell host of open ports after resume from s3/s4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"I will stop trying to predict when we're done with fixes for a
release.
Here's another small batch of three patches for arm-soc:
- A fix for a boot time WARN_ON() due to irq domain conversion on
PRIMA2
- Fix for a regression in Tegra SMP spinup code due to swapped
register offsets
- Fixed config dependency for mv_cesa crypto driver to avoid build
breakage"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PRIMA2: fix irq domain size and IRQ mask of internal interrupt controller
crypto: mv_cesa requires on CRYPTO_HASH to build
ARM: tegra: Fix flow controller accesses
|
|
Pull two md fixes from NeilBrown:
"One fixes a bug in the new raid10 resize code so is relevant to 3.4
only.
The other fixes a bug in the use of md by dm-raid, so is relevant to
any kernel with dm-raid support"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
MD: Add del_timer_sync to mddev_suspend (fix nasty panic)
md/raid10: set dev_sectors properly when resizing devices in array.
|
|
__napi_schedule might raise softirq but nothing
causes do_softirq to trigger, so it does not in fact
run. As a result,
the error message "NOHZ: local_softirq_pending 08"
sometimes occurs during boot of a KVM guest when the network service is
started and we are oom:
...
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0...NOHZ: local_softirq_pending 08
done.
[ OK ]
...
Further, receive queue processing might get delayed
indefinitely until some interrupt triggers:
virtio_net expected napi to be run immediately.
One way to cause do_softirq to be executed is by
invoking local_bh_enable(). As __napi_schedule is
normally called from bh or irq context, this
seems to make sense: disable bh before __napi_schedule
and enable afterwards.
In fact it's a very complicated way of calling do_softirq(),
and works since this function is only used when we are not
in interrupt context. It's not hot at all, in any ideal scenario.
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Tested-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
When the balloon module is removed, we deflate the balloon, reclaiming
all the pages that were given to the host. However, we don't update the
config values for the new balloon size, resulting in the host showing
outdated balloon values.
The size update is done after each leak and fill operation, only the
module removal case was left out.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
If a port was open before going into one of the sleep states, the port
can continue normal operation after restore. However, the host has to
be told that the guest side of the connection is open to restore
pre-suspend state.
This wasn't noticed so far due to a bug in qemu that was fixed recently
(which marked the guest-side connection as always open).
CC: stable@vger.kernel.org # Only for 3.3
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Use del_timer_sync to remove timer before mddev_suspend finishes.
We don't want a timer going off after an mddev_suspend is called. This is
especially true with device-mapper, since it can call the destructor function
immediately following a suspend. This results in the removal (kfree) of the
structures upon which the timer depends - resulting in a very ugly panic.
Therefore, we add a del_timer_sync to mddev_suspend to prevent this.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
raid10 stores dev_sectors in 'conf' separately from the one in
'mddev' because it can have a very significant effect on block
addressing and so need to be updated carefully.
However raid10_resize isn't updating it at all!
To update it correctly, we need to make sure it is a proper
multiple of the chunksize taking various details of the layout
in to account.
This calculation is currently done in setup_conf. So split it
out from there and call it from raid10_resize as well.
Then set conf->dev_sectors properly.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc fix from Ohad Ben-Cohen:
"Fix a nasty off-by-one remoteproc bug which leaks memory when a remote
processor is shut down and, on certain circumstances, can indirectly
prevent it from being reloaded."
* tag 'rproc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: fix off-by-one bug in __rproc_free_vrings
|
|
Pull networking tree from David Miller:
1) ptp_pch driver build broke during this merge window due to missing
slab.h header, fix from Geery Uytterhoeven.
2) If ipset passes in a bogus hash table size we crash because the size
is not validated properly. Compounding this, gcc-4.7 can miscompile
ipset such that even when the user specifies legitimate parameters
the tool passes in an out-of-range size to the kernel.
Fix from Jozsef Kadlecsik.
3) Users have reported that the netdev watchdog can trigger with pch_gbe
devices, and it turns out this is happening because of races in the
TX path of the driver leading to the transmitter hanging. Fix from
Eric Dumazet, reported and tested by Andy Cress.
4) Novatel USB551L devices match the generic class entries for the cdc
ethernet USB driver, but they don't work because they have generic
descriptors and thus need FLAG_WWAN to function properly.
Add the necessary ID table entry to fix this, from Dan Williams.
5) A recursive locking fix in the USBNET driver added a new problem, in
that packet list traversal is now racy and we can thus access
unlinked SKBs and crash.
Avoid this situation by adding some extra state tracking, from Ming
Lei.
6) The rtlwifi conversion to asynchronous firmware loading is racy, fix
by reordering the probe procedure. From Larry Finger.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=43187
7) Fix regressions with bluetooth keyboards by notifying userland
properly when the security level changes, from Gustavo Padovan.
8) Bluetooth needs to make sure device connected events are emitted
before other kinds of events, otherwise userspace will think there is
no baseband link yet and therefore abort the sockets associated with
that connection.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ipset: fix hash size checking in kernel
ptp_pch: Add missing #include <linux/slab.h>
pch_gbe: fix transmit races
cdc_ether: add Novatel USB551L device IDs for FLAG_WWAN
usbnet: fix skb traversing races during unlink(v2)
Bluetooth: mgmt: Fix device_connected sending order
Bluetooth: notify userspace of security level change
rtlwifi: fix for race condition when firmware is cached
|
|
drivers/ptp/ptp_pch.c: In function 'pch_remove':
drivers/ptp/ptp_pch.c:576:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
drivers/ptp/ptp_pch.c: In function 'pch_probe':
drivers/ptp/ptp_pch.c:587:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John Linville says:
Here are three more fixes that some of my developers are desperate to
see included in 3.4...
Johan Hedberg went to some length justifyng the inclusion of these two
Bluetooth fixes:
"The device_connected fix should be quite self-explanatory, but it's
actually a wider issue than just for keyboards. All profiles that do
incoming connection authorization (e.g. headsets) will break without it
with specific hardware. The reason it wasn't caught earlier is that it
only occurs with specific Bluetooth adapters.
As for the security level patch, this fixes L2CAP socket based security
level elevation during a connection. The HID profile needs this (for
keyboards) and it is the only way to achieve the security level
elevation when using the management interface to talk to the kernel
(hence the management enabling patch being the one that exposes this"
The rtlwifi fix addresses a regression related to firmware loading,
as described in kernel.org bug 43187. It basically just moves a hunk
of code to a more appropriate place.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Andy reported pch_gbe triggered "NETDEV WATCHDOG" errors.
May 11 11:06:09 kontron kernel: WARNING: at net/sched/sch_generic.c:261
dev_watchdog+0x1ec/0x200() (Not tainted)
May 11 11:06:09 kontron kernel: Hardware name: N/A
May 11 11:06:09 kontron kernel: NETDEV WATCHDOG: eth0 (pch_gbe):
transmit queue 0 timed out
It seems pch_gbe has a racy tx path (races with TX completion path)
Remove tx_queue_lock lock since it has no purpose, we must use tx_lock
instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Cress <andy.cress@us.kontron.com>
Tested-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Needs to be tagged with FLAG_WWAN, which since it has generic
descriptors, won't happen if we don't override the generic
driver info.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock before unlink, but may
cause skb traversing races:
- after URB is unlinked and the queue lock is released,
the refered skb and skb->next may be moved to done queue,
even be released
- in skb_queue_walk_safe, the next skb is still obtained
by next pointer of the last skb
- so maybe trigger oops or other problems
This patch extends the usage of entry->state to describe 'start_unlink'
state, so always holding the queue(rx/tx) lock to change the state if
the referd skb is in rx or tx queue because we need to know if the
refered urb has been started unlinking in unlink_urbs.
The other part of this patch is based on Huajun's patch:
always traverse from head of the tx/rx queue to get skb which is
to be unlinked but not been started unlinking.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for cyclic dma, dont makr the descriptor as complte. Fix the remaining users of
cyclic dma which do so
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Mika Westerberg <mika.westerberg@iki.fi>
|
|
Without CRYPTO_HASH being selected, mv_cesa has a lot of hooks
into undefined exports.
----
MODPOST 81 modules
Kernel: arch/arm/boot/Image is ready
AS arch/arm/boot/compressed/head.o
GZIP arch/arm/boot/compressed/piggy.gzip
CC arch/arm/boot/compressed/misc.o
CC arch/arm/boot/compressed/decompress.o
ERROR: "crypto_ahash_type" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_final" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_register_ahash" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_unregister_ahash" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_update" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_digest" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_shash_setkey" [drivers/crypto/mv_cesa.ko] undefined!
ERROR: "crypto_alloc_shash" [drivers/crypto/mv_cesa.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
make: *** Waiting for unfinished jobs....
----
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
|
|
This patch addresses a bug in a special case for target core SPC-2 RELEASE
logic where the same physical client (eg: iSCSI InitiatorName) with
differing iSCSI session identifiers (ISID) is allowed to incorrectly release
the same client's SPC-2 reservation from the non reservation holding path.
Note this bug is specific to iscsi-target w/ SPC-2 reservations, and
with the default enforce_pr_isids=1 device attr setting in target-core
controls if a InitiatorName + different ISID reservations are handled
the same as a single iSCSI client entity.
Signed-off-by: Bernhard Kohl <bernhard.kohl@gmx.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For a some fix patches for v3.4, including a regression fix at DVB core"
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca - sonixj: Fix a zero divide in isoc interrupt
[media] media: videobuf2-dma-contig: include header for exported symbols
[media] media: videobuf2-dma-contig: quiet sparse noise about plain integer as NULL pointer
[media] media: vb2-memops: Export vb2_get_vma symbol
[media] s5p-fimc: Correct memory allocation for VIDIOC_CREATE_BUFS
[media] s5p-fimc: Fix locking in subdev set_crop op
[media] dvb_frontend: fix a regression with DVB-S zig-zag
[media] fintek-cir: change || to &&
[media] V4L: Schedule V4L2_CID_HCENTER, V4L2_CID_VCENTER controls for removal
[media] rc: Postpone ISR registration
[media] marvell-cam: fix an ARM build error
[media] V4L: soc-camera: protect hosts during probing from overzealous user-space
|
|
Pull networking fixes from David Miller:
"The main purpose of this pull request is to fix up the erroneous
bonding patch I applied last round. I meant to apply v4 of the patch
from Jiri but I applied v3 by accident. Mea culpa.
Also, eagle eyed Dan Carpenter noticed that openvswitch has one of
those "X = alloc(); if (!Y)" mistakes, test the proper pointer
instead."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
|
|
In commit b0302ab, the rtlwifi family of drivers was converted to use
asynchronous firmware loading. Unfortumately, the implementation was
racy, and the ieee80211 routines could be started before rtl_init_core()
was called to setup the data.
This patch fixes the bug noted in https://bugzilla.kernel.org/show_bug.cgi?id=43187.
Reported-by: Joshua Roys <Joshua.Roys@gtri.gatech.edu>
Tested-by: Neptune Ning <frostyplanet@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.3]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
3.4-rc introduced a regression when setting the LEDS. We do the right thing
but then return an error code.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43144
Reported-by: Christian Casteyde
Signed-off-by: Alan Cox <alan@linux/intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
