Age | Commit message (Collapse) | Author |
|
Add support for blackhole nexthops by programming them to the adjacency
table with a discard action.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The two are the same, but for blackhole nexthops we will not have an
associated neighbour struct, so resolve the RIF from the nexthop struct
itself instead.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the driver creates a loopback RIF during its initialization, it
can be used to program the adjacency entries for unresolved nexthops
instead of other RIFs. The loopback RIF is guaranteed to exist for the
entire life time of the driver, unlike other RIFs that come and go.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unresolved nexthops are currently written to the adjacency table with a
discard action. Packets hitting such entries are trapped to the CPU via
the 'DISCARD_ROUTER3' trap which can be enabled or disabled on demand,
but is always enabled in order to ensure the kernel can resolve the
unresolved neighbours.
This trap will be needed for blackhole nexthops support. Therefore, move
unresolved nexthops to explicitly program the adjacency entries with a
trap action and a different trap identifier, 'RTR_EGRESS0'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Up until now RIFs (router interfaces) were created on demand (e.g.,
when an IP address was added to a netdev). However, sometimes the device
needs to be provided with a RIF when one might not be available.
For example, adjacency entries that drop packets need to be programmed
with an egress RIF despite the RIF not being used to forward packets.
Create such a RIF during initialization so that it could be used later
on to support blackhole nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver uses a normal timer for TX coalescing, which means that the
with the default tx-usecs of 1000 microseconds the cleanups actually
happen 10 ms or more later with HZ=100. This leads to very low
througput with TCP when bridged to a slow link such as a 4G modem. Fix
this by using an hrtimer instead.
On my ARM platform with HZ=100 and the default TX coalescing settings
(tx-frames 25 tx-usecs 1000), with "tc qdisc add dev eth0 root netem
delay 60ms 40ms rate 50Mbit" run on the server, netperf's TCP_STREAM
improves from ~5.5 Mbps to ~100 Mbps.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20201120150208.6838-1-vincent.whitchurch@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Memory allocation are done with 'dma_alloc_coherent()'. Be consistent
and use 'dma_free_coherent()' to free the corresponding memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201121090330.1332543-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'pci_set_dma_mask()' + 'pci_set_consistent_dma_mask()' can be replaced by
an equivalent 'dma_set_mask_and_coherent()' which is much less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201121090302.1332491-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When DSA is not loaded when the driver is probed an error message is
printed. But, that's not really an error, just a defer. Use dev_err_probe()
instead.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove driver internal defines for this. Masking msgtype with 0xf is
already done within ptp_get_msgtype().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove usage of magic numbers.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Call netdev notifiers before and after changing the device type.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20201118063919.29485-1-ms@dev.tdt.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to choose RSS flow key algorithm with IPv4 transport protocol
field included in hashing input data. This will be enabled by default.
There-by enabling 3/5 tuple hash
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: George Cherian <george.cherian@marvell.com>
Link: https://lore.kernel.org/r/20201120093906.2873616-1-george.cherian@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2020-11-20
The first patch is by Yegor Yefremov and he improves the j1939 documentaton by
adding tables for the CAN identifier and its fields.
Then there are 8 patches by Oliver Hartkopp targeting the CAN driver
infrastructure and drivers. These add support for optional DLC element to the
Classical CAN frame structure. See patch ea7800565a12 ("can: add optional DLC
element to Classical CAN frame structure") for details. Oliver's last patch
adds len8_dlc support to several drivers. Stefan Mätje provides a patch to add
len8_dlc support to the esd_usb2 driver.
The next patch is by Oliver Hartkopp, too and adds support for modification of
Classical CAN DLCs to CAN GW sockets.
The next 3 patches target the nxp,flexcan DT bindings. One patch by my adds the
missing uint32 reference to the clock-frequency property. Joakim Zhang's
patches fix the fsl,clk-source property and add the IMX_SC_R_CAN() macro to the
imx firmware header file, which will be used in the flexcan driver later.
Another patch by Joakim Zhang prepares the flexcan driver for SCU based
stop-mode, by giving the existing, GPR based stop-mode, a _GPR postfix.
The next 5 patches are by me, target the flexcan driver, and clean up the
.ndo_open and .ndo_stop callbacks. These patches try to fix a sporadically
hanging flexcan_close() during simultanious ifdown, sending of CAN messages and
probably open CAN bus. I was never able to reproduce, but these seem to fix the
problem at the reporting user. As these changes are rather big, I'd like to
mainline them via net-next/master.
The next patches are by Jimmy Assarsson and Christer Beskow, they add support
for new USB devices to the existing kvaser_usb driver.
The last patch is by Kaixu Xia and simplifies the return in the
mcp251xfd_chip_softreset() function in the mcp251xfd driver.
* tag 'linux-can-next-for-5.11-20201120' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (25 commits)
can: mcp251xfd: remove useless code in mcp251xfd_chip_softreset
can: kvaser_usb: Add new Kvaser hydra devices
can: kvaser_usb: kvaser_usb_hydra: Add support for new device variant
can: kvaser_usb: Add new Kvaser Leaf v2 devices
can: kvaser_usb: Add USB_{LEAF,HYDRA}_PRODUCT_ID_END defines
can: flexcan: flexcan_close(): change order if commands to properly shut down the controller
can: flexcan: flexcan_open(): completely initialize controller before requesting IRQ
can: flexcan: flexcan_rx_offload_setup(): factor out mailbox and rx-offload setup into separate function
can: flexcan: move enabling/disabling of interrupts from flexcan_chip_{start,stop}() to callers
can: flexcan: factor out enabling and disabling of interrupts into separate function
can: flexcan: rename macro FLEXCAN_QUIRK_SETUP_STOP_MODE -> FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
dt-bindings: firmware: add IMX_SC_R_CAN(x) macro for CAN
dt-bindings: can: fsl,flexcan: fix fsl,clk-source property
dt-bindings: can: fsl,flexcan: add uint32 reference to clock-frequency property
can: gw: support modification of Classical CAN DLCs
can: drivers: add len8_dlc support for esd_usb2 CAN adapter
can: drivers: add len8_dlc support for various CAN adapters
can: drivers: introduce helpers to access Classical CAN DLC values
can: update documentation for DLC usage in Classical CAN
can: rename CAN FD related can_len2dlc and can_dlc2len helpers
...
====================
Link: https://lore.kernel.org/r/20201120133318.3428231-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adds debugfs to dump new shaping parameters: rate and flag.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the calculation of the driver is fixed, if the number of
queue or clock changed, the calculated result may be inaccurate.
So for compatible and maintainable, add a new flag to tell the
firmware to calculate the shaping parameters with the specified
rate.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For HNAE3_DEVICE_VERSION_V3, a maximum of 1281 interrupt
resources are supported. To utilize these new resources,
extend the corresponding field or variable to 16bit type,
and remove the restriction of NIC client that only use a
maximum of 65 interrupt vectors. In addition, the I/O address
of the extended interrupt resources are different, so an extra
handler is needed.
Currently, the total number of interrupts is the sum of RoCE's
number and RoCE's offset (RoCE is in front of NIC), since
the number of both NIC and RoCE are same. For readability,
rewrite the corresponding field of the command, rename the
RoCE's offset field as the number of NIC interrupts, then
the total number of interrupts is sum of the number of RoCE
and NIC, and replace vport->back with hdev in
hclge_init_roce_base_info() for simplifying the code.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For device who has device memory accessed through the PCI BAR4,
IO descriptor push of NIC and direct WQE(Work Queue Element) of
RoCE will use this device memory, so add support for mapping
this device memory, and add this info to the RoCE client whose
new feature needs.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For DEVICE_VERSION_V1/2, there are total 1024 queues and
queue sets. For DEVICE_VERSION_V3, it increases to 1280,
and can be assigned to one pf, so remove the limitation
of 1024.
To keep compatible with DEVICE_VERSION_V1/2 and old driver
version, the queue number is split into two part:
tqp_num(range 0~1023) and ext_tqp_num(range 1024~1279).
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reduce the amount of time spent replenishing RX buffers by only doing
so once available buffers has fallen under a certain threshold, in this
case half of the total number of buffers, or if the polling loop exits
before the packets processed is less than its budget. Non-exhaustion of
NAPI budget implies lower incoming packet pressure, allowing the leeway
to refill the buffers in preparation for any impending burst.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Take advantage of the additional optimizations in netdev_alloc_skb when
allocating socket buffers to be used for packet reception.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the current NAPI polling loop exits without completing it's
budget, only re-enable interrupts if there are no entries remaining
in the queue and napi_complete_done is successful. If there are entries
remaining on the queue that were missed, restart the polling loop.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PCI bus slowdowns were observed on IBM VNIC devices as a result
of partial cache line writes and non-cache aligned full cache line writes.
Ensure that packet data buffers are cache-line aligned to avoid these
slowdowns.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is not longer used, so remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unused and superfluous code and members in
existing TX implementation and data structures.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Include support for the xmit_more feature utilizing the
H_SEND_SUB_CRQ_INDIRECT hypervisor call which allows the sending
of multiple subordinate Command Response Queue descriptors in one
hypervisor call via a DMA-mapped buffer. This update reduces hypervisor
calls and thus hypervisor call overhead per TX descriptor.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Utilize the H_SEND_SUB_CRQ_INDIRECT hypervisor call to send
multiple RX buffer descriptors to the device in one hypervisor
call operation. This change will reduce the number of hypervisor
calls and thus hypervisor call overhead needed to transmit
RX buffer descriptors to the device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch introduces the infrastructure to send batched subordinate
Command Response Queue descriptors, which are used by the ibmvnic
driver to send TX frame and RX buffer descriptors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A system shutdown can happen at essentially any time, and it's
possible that the IPA driver is busy when a shutdown is underway.
IPA hardware accesses IMEM and SMEM memory regions using an IOMMU,
and at some point during shutdown, needed I/O mappings could become
invalid. This could be disastrous for any "in flight" IPA activity.
Avoid this by defining a new driver shutdown callback that stops all
IPA activity and cleanly shuts down the driver. It merely calls the
driver's existing remove callback, reporting the error if it returns
one.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IPA driver remove callback, ipa_remove(), calls ipa_modem_stop()
if the setup stage of initialization is complete. If a concurrent
call to ipa_modem_start() or ipa_modem_stop() has begin but not
completed, ipa_modem_stop() can return an error (-EBUSY).
The next patch adds a driver shutdown callback, which will simply
call ipa_remove(). We really want our shutdown callback to clean
things up. So add a single retry to the ipa_modem_stop() call in
ipa_remove() after a short (millisecond) delay. This offers no
guarantee the shutdown will complete successfully, but we'll at
least try a little harder before giving up.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When stopping an AP RX channel, there can be a transient period
while the channel enters STOP_IN_PROC state before reaching the
final STOPPED state. In that case we make another attempt to stop
the channel.
Similarly, when stopping a modem channel (using a GSI generic
command issued from the AP), it's possible that multiple attempts
will be required before the channel reaches STOPPED state.
Add a field to the GSI structure to record an errno representing the
result code provided when a generic command completes. If the
result learned in gsi_isr_gp_int1() is RETRY, record -EAGAIN in the
result code, otherwise record 0 for success, or -EIO for any other
result.
If we time out nf gsi_generic_command() waiting for the command to
complete, return -ETIMEDOUT (as before). Otherwise return the
result stashed by gsi_isr_gp_int1().
Add a loop in gsi_modem_channel_halt() to reissue the HALT command
if the result code indicates -EAGAIN. Limit this to 10 retries
(after the initial attempt).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v4.2 has a hardware quirk that requires the AP to allocate GSI
channels for the modem to use. It is recommended that these modem
channels get stopped (with a HALT generic command) by the AP when
its IPA driver gets removed.
The AP has no way of knowing the current state of a modem channel.
So when the IPA driver issues a HALT command it's possible the
channel is not running, and in that case we get an error indication.
This error simply means we didn't need to stop the channel, so we
can ignore it.
This patch adds an explanation for this situation, and arranges for
this condition to *not* report an error message.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the rmnet_ipa0 network device has not been opened at the time
we remove or shut down the IPA driver, its underlying TX and RX
GSI channels will not have been started, and they will still be
in ALLOCATED state.
The RESET command on a channel is meant to return a channel to
ALLOCATED state after it's been stopped. But if it was never
started, its state will still be ALLOCATED, the RESET command
is not required.
Quietly skip doing the reset without printing an error message if a
channel is already in ALLOCATED state when we request it be reset.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a GSI command is used to change the state of a channel or event
ring we check the state before and after the command to ensure it is
as expected. If not, we print an error message, but it does not
include the channel or event ring id, and it easily can. Add the
channel or event ring id to these error messages.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stop assuming a fixed IPA core clock rate and interconnect
bandwidths. Use the configuration data defined for these
things instead. Get rid of the previously-used constants.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Populate the core clock rate and interconnect average and peak
bandwidth data for SDM845 and SC7180 in their configuration data
files. At this point we still don't *use* this data.
Note that SC7180 actually defines a new core clock rate (100 MHz
instead of 75 MHz) and new interconnect bandwidth values. They
will be activated in the next commit, which uses the configured
values rather than the fixed constants.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define a new type of configuration data, used to initialize the
IPA core clock and interconnects. This is the first of three
patches, and defines the data types and interface but doesn't
yet use them.
Switch the return value if there is no matching configuration data
to ENODEV instead of ENOTSUPP (to avoid using the nonstandard errno).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mdio_bus may have dependencies from GPIO controller and so got
deferred. Now it will print error message every time -EPROBE_DEFER is
returned which from:
__mdiobus_register()
|-devm_gpiod_get_optional()
without actually identifying error code.
"mdio_bus 4a101000.mdio: mii_bus 4a101000.mdio couldn't get reset GPIO"
Hence, suppress error message for devm_gpiod_get_optional() returning
-EPROBE_DEFER case by using dev_err_probe().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201119203446.20857-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tiny improvement, let dev_err_probe() deal with EPROBE_DEFER.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/b0c4ebcf-2047-e933-b890-8a20e4bdb19f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some chip versions have a hw bug resulting in lost door bell rings.
To work around this the doorbell is also rung whenever we still have
tx descriptors in flight after having cleaned up tx descriptors.
These PCI(e) writes come at a cost, therefore let's reduce the number
of extra doorbell rings.
If skb is NULL then this means:
- last cleaned-up descriptor belongs to a skb with at least one fragment
and last fragment isn't marked as sent yet
- hw is in progress sending the skb, therefore no extra doorbell ring
is needed for this skb
- once last fragment is marked as transmitted hw will trigger
a tx done interrupt and we come here again (with skb != NULL)
and ring the doorbell if needed
Therefore skip the workaround doorbell ring if skb is NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/0a15a83c-aecf-ab51-8071-b29d9dcd529a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the driver supports nexthop objects, the check is no longer
necessary. Remove it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the FIB info (i.e, 'struct fib_info', 'struct fib6_info') uses a
nexthop object, then use the object's identifier to resolve the nexthop
group.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Register a listener to the nexthop notification chain and parse notified
nexthop objects into the existing mlxsw nexthop data structures.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add ethtool ring and coalesce settings support for testing.
Signed-off-by: Antonio Cardace <acardace@redhat.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This will help the refactoring in the next commit
when coalesce and ring settings are added.
Signed-off-by: Antonio Cardace <acardace@redhat.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The call to pc_delete_flow can kfree the iter object, so the following
dev_err message that accesses iter->entry can accessmemory that has
just been kfree'd. Fix this by adding a temporary variable 'entry'
that has a copy of iter->entry and also use this when indexing into
the array mcam->entry2target_pffunc[]. Also print the unsigned value
using the %u format specifier rather than %d.
Addresses-Coverity: ("Read from pointer after free")
Fixes: 55307fcb9258 ("octeontx2-af: Add mbox messages to install and delete MCAM rules")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201118143803.463297-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the variable err may be uninitialized if several of the if
statements are not executed in function nix_tx_vtag_decfg and a garbage
value in err is returned. Fix this by initialized ret at the start of
the function.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 9a946def264d ("octeontx2-af: Modify nix_vtag_cfg mailbox to support TX VTAG entries")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201118132502.461098-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The shifting of the u16 result from ntohs(proto) by 16 bits to the
left will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the event that the top bit of the return from ntohs(proto)
is set then all then all the upper 32 bits of a 64 bit long end up as
also being set because of the sign-extension. Fix this by casting to
a u64 long before the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: f0c2982aaf98 ("octeontx2-pf: Add support for SR-IOV management function")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201118130520.460365-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add entries to debugfs at /sys/kernel/debug/octeontx2/cpt.
cpt_pc: dump cpt performance HW registers.
Usage:
cat /sys/kernel/debug/octeontx2/cpt/cpt_pc
cpt_ae_sts: show cpt asymmetric engines current state
Usage:
cat /sys/kernel/debug/octeontx2/cpt/cpt_ae_sts
cpt_se_sts: show cpt symmetric engines current state
Usage:
cat /sys/kernel/debug/octeontx2/cpt/cpt_se_sts
cpt_engines_info: dump cpt engine control registers.
Usage:
cat /sys/kernel/debug/octeontx2/cpt/cpt_engines_info
cpt_lfs_info: dump cpt lfs control registers.
Usage:
cat /sys/kernel/debug/octeontx2/cpt/cpt_lfs_info
cpt_err_info: dump cpt error registers.
Usage:
cat /sys/kernel/debug/octeontx2/cpt/cpt_err_info
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|