| Age | Commit message (Collapse) | Author |
|---|
|
The standard way to check if the AQ is enabled is to look at the
count field. So we should only set this field after we have
successfully allocated memory. To do otherwise is to incite
panic among the populace.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kasprintf function can return NULL if the allocation fails. Check for
successful allocation before attempting to use the returned buffer.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver still was not offloading TSO on GRE tunnels because
it forgot to set the GSO_GRE flag, causing lots of retransmits.
This fixes generic GRE traffic (like a tunnel added like below)
whereas before it would get 1Gb/s or less, now on a 10G adapter
it gets 8.7Gb/s.
ip ad ad 11.1.0.2/24 dev ens2f0
ip l set ens2f0 up
ip link add gre2 type gretap remote 11.1.0.1 local 11.1.0.2 dev ens2f0
ip l set gre2 up
ip ad ad 192.168.124.2/24 dev gre2
ping 192.168.124.1
netperf -H 192.168.124.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
pull-request: wireless-drivers 2015-10-01
ath9k:
* declare required extra tx headroom
ath10k:
* fix DMA related firmware crashes on multiple devices
rt2800usb:
* add usb ID 1b75:3070 for Airlive WT-2000USB
b43:
* probe bcma core (device) rev 0x15
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If common clock framework is configured, the driver generates warnings,
which are fixed by this change:
WARNING: CPU: 0 PID: 1 at linux/drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #141
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc_eth_drv_probe+0xfc/0x99c)
[<>] (lpc_eth_drv_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (lpc_eth_driver_init+0x18/0x20)
[<>] (lpc_eth_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If asix_rx_fixup_internal() fails to allocate rx->ax_skb, it will return
but not clear rx->size. rx points to driver private data. A later call
assumes that nonzero size means ax_skb was allocated and passes a null
ax_skb to skb_put. Changed allocation failure return to clear size first.
Found testing board with AX88772B devices.
Signed-off-by: David B. Robins <linux@davidrobins.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-09-30
this is a pull request of a single patch for 4.3.
The patch is by Stephane Grosjean and add support for the peak OEM PCI card to
the peak_pci driver by adding its device ID.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added kfree() to avoid the memory leak when debugfs_create_dir() fails.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"),
pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the
PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to
PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the
following oops:
[ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0
[ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0
[ 570.144601] Oops: 0000 [#1] SMP
[ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio
[ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1
[ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000
[ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202
[ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206
[ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20
[ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000
[ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780
[ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0
[ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000
[ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0
[ 570.144601] Stack:
[ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0
[ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008
[ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5
[ 570.144601] Call Trace:
[ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75
[ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11
[ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5
[ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb
[ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90
[ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7
[ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b
[ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f
[ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00
[ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe]
[ 570.144601] RSP <ffff880036b63e08>
[ 570.144601] CR2: 00000000000004e0
[ 570.200518] ---[ end trace 46956baf17349563 ]---
pppoe_flush_dev() has no reason to override sk->sk_state with
PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to
PPPOX_DEAD, which is the correct state given that sk is unbound and
po->pppoe_dev is NULL.
Fixes: 2b018d57ff18 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release")
Tested-by: Oleksii Berezhniak <core@irc.lg.ua>
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.3 rc4:
MMC core:
- Allow users of mmc_of_parse() to succeed when CONFIG_GPIOLIB is
unset
- Prevent infinite loop of re-tuning for CRC-errors for CMD19 and
CMD21
MMC host:
- pxamci: Fix issues with card detect
- sunxi: Fix clk-delay settings"
* tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: fix dead loop of mmc_retune
mmc: pxamci: fix card detect with slot-gpio API
mmc: sunxi: Fix clk-delay settings
mmc: core: Don't return an error for CD/WP GPIOs when GPIOLIB is unset
|
|
Pull IOVA fixes from David Woodhouse:
"The main fix here is the first one, fixing the over-allocation of
size-aligned requests. The other patches simply make the existing
IOVA code available to users other than the Intel VT-d driver, with no
functional change.
I concede the latter really *should* have been submitted during the
merge window, but since it's basically risk-free and people are
waiting to build on top of it and it's my fault I didn't get it in, I
(and they) would be grateful if you'd take it"
* git://git.infradead.org/intel-iommu:
iommu: Make the iova library a module
iommu: iova: Export symbols
iommu: iova: Move iova cache management to the iova library
iommu/iova: Avoid over-allocating when size-aligned
|
|
Merge misc fixes from Andrew Morton:
"12 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dmapool: fix overflow condition in pool_find_page()
thermal: avoid division by zero in power allocator
memcg: remove pcp_counter_lock
kprobes: use _do_fork() in samples to make them work again
drivers/input/joystick/Kconfig: zhenhua.c needs BITREVERSE
memcg: make mem_cgroup_read_stat() unsigned
memcg: fix dirty page migration
dax: fix NULL pointer in __dax_pmd_fault()
mm: hugetlbfs: skip shared VMAs when unmapping private pages to satisfy a fault
mm/slab: fix unexpected index mapping result of kmalloc_size(INDEX_NODE+1)
userfaultfd: remove kernel header include from uapi header
arch/x86/include/asm/efi.h: fix build failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes mostly, for a few changes made in this cycle (the
intel_idle driver, the OPP library, the ACPI EC driver, turbostat) and
for some issues that have just been discovered (ACPI PCI IRQ
management, PCI power management documentation, turbostat), with a
couple of cleanups on top of them.
Specifics:
- intel_idle driver fixup for the recently added Skylake chips
support (Len Brown).
- Operating Performance Points (OPP) library fix related to the
recently added support for new DT bindings and a fix for a typo in
a comment (Viresh Kumar, Stephen Boyd).
- ACPI EC driver fix for a recently introduced memory leak in an
error code path (Lv Zheng).
- ACPI PCI IRQ management fix for the issue where an ISA IRQ is
shared with a PCI device which requires it to be configured in a
different way and may cause an interrupt storm to happen as a
result with an extra ACPI SCI IRQ handling simplification on top of
it (Jiang Liu).
- Update of the PCI power management documentation that became
outdated and started to actively confuse the readers to make it
actually reflect the code (Rafael J Wysocki).
- turbostat fixes including an IVB Xeon regression fix (related to
the --debug command line option), Skylake adjustment for the TSC
running at a frequency that doesn't match the base one exactly, and
a Knights Landing quirk to account for the fact that it only
updates APERF and MPERF every 1024 clock cycles plus bumping up the
turbostat version number (Len Brown, Hubert Chrzaniuk)"
* tag 'pm+acpi-4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power turbosat: update version number
tools/power turbostat: SKL: Adjust for TSC difference from base frequency
tools/power turbostat: KNL workaround for %Busy and Avg_MHz
tools/power turbostat: IVB Xeon: fix --debug regression
ACPI / PCI: Remove duplicated penalty on SCI IRQ
ACPI, PCI, irq: Do not share PCI IRQ with ISA IRQ
ACPI / EC: Fix a memory leak issue in acpi_ec_query()
PM / OPP: Fix typo modifcation -> modification
PCI / PM: Update runtime PM documentation for PCI devices
PM / OPP: of_property_count_u32_elems() can return errors
intel_idle: Skylake Client Support - updated
|
|
Pull networking fixes from David Miller:
1) Fix regression in SKB partial checksum handling, from Pravin B
Shalar.
2) Fix VLAN inside of VXLAN handling in i40e driver, from Jesse
Brandeburg.
3) Cure softlockups during accept() in SCTP, from Karl Heiss.
4) MSG_PEEK should return multiple SKBs worth of data in AF_UNIX, from
Aaron Conole.
5) IPV6 erroneously ignores output interface specifier in lookup key for
route lookups, fix from David Ahern.
6) In Marvell DSA driver, forward unknown frames to CPU port, from
Andrew Lunn.
7) Mission flow flag initializations in some code paths, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Initialize flow flags in input path
net: dsa: fix preparation of a port STP update
testptp: Silence compiler warnings on ppc64
net/mlx4: Handle return codes in mlx4_qp_attach_common
dsa: mv88e6xxx: Enable forwarding for unknown to the CPU port
skbuff: Fix skb checksum partial check.
net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set
net sysfs: Print link speed as signed integer
bna: fix error handling
af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag
af_unix: Convert the unix_sk macro to an inline function for type safety
net: sctp: Don't use 64 kilobyte lookup table for four elements
l2tp: protect tunnel->del_work by ref_count
net/ibm/emac: bump version numbers for correct work with ethtool
sctp: Prevent soft lockup when sctp_accept() is called during a timeout event
sctp: Whitespace fix
i40e/i40evf: check for stopped admin queue
i40e: fix VLAN inside VXLAN
r8169: fix handling rtl_readphy result
net: hisilicon: fix handling platform_get_irq result
|
|
During boot I get a div by zero Oops regression starting in v4.3-rc3.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in
vmlinux.
Cc: Fengguang Wu <fengguang.wu@gmail.com>
Cc: yalin wang <yalin.wang2010@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Fixes for mlx5 related issues
- Fixes for ipoib multicast handling
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: increase the max mcast backlog queue
IB/ipoib: Make sendonly multicast joins create the mcast group
IB/ipoib: Expire sendonly multicast joins
IB/mlx5: Remove pa_lkey usages
IB/mlx5: Remove support for IB_DEVICE_LOCAL_DMA_LKEY
IB/iser: Add module parameter for always register memory
xprtrdma: Replace global lkey with lkey local to PD
|
|
* pm-cpuidle:
intel_idle: Skylake Client Support - updated
* pm-opp:
PM / OPP: Fix typo modifcation -> modification
PM / OPP: of_property_count_u32_elems() can return errors
* pm-tools:
tools/power turbosat: update version number
tools/power turbostat: SKL: Adjust for TSC difference from base frequency
tools/power turbostat: KNL workaround for %Busy and Avg_MHz
tools/power turbostat: IVB Xeon: fix --debug regression
|
|
* acpi-ec:
ACPI / EC: Fix a memory leak issue in acpi_ec_query()
|
|
* pm-pci:
PCI / PM: Update runtime PM documentation for PCI devices
* acpi-pci:
ACPI / PCI: Remove duplicated penalty on SCI IRQ
ACPI, PCI, irq: Do not share PCI IRQ with ISA IRQ
|
|
Pull UBI/UBIFS fixes from Richard Weinberger:
"This contains three bug fixes for both UBI and UBIFS"
* tag 'upstream-4.3-rc4' of git://git.infradead.org/linux-ubifs:
UBI: return ENOSPC if no enough space available
UBI: Validate data_size
UBIFS: Kill unneeded locking in ubifs_init_security
|
|
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes:
- module autoload for 3 OF platform drivers
- poweroff behaviour on bcm2835 watchdog device
- I2C dependencies for iTCO_wdt.c"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO: Fix dependencies on I2C
watchdog: bcm2835: Fix poweroff behaviour
watchdog: Fix module autoload for OF platform driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmin fixes from Guenter Roeck:
"Fix module autoload for various drivers"
* tag 'hwmon-for-linus-v4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pwm-fan) Fix module autoload for OF platform driver
hwmon: (gpio-fan) Fix module autoload for OF platform driver
hwmon: (abx500) Fix module autoload for OF platform driver
|
|
When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21
to do tune, assume there were 10 clock phase need to try, phase 0 to
phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so
the last CMD19/CMD21 will get CRC error, host->need_retune was set and
cause mmc_retune was called, then dead loop of mmc_retune
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
While new PEAK_PCIE_OEM_ID has been defined since 3.17, no corresponding
entry has been added in the peak_pci_tbl[] of the peak_pci CAN driver.
This patch enables now users of the PCAN-PCI Express OEM card to run the
peak_pci driver too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Both new_steering_entry() and existing_steering_entry() return values
based on their success or failure, but currently they fall through
silently. This can make troubleshooting difficult, as we were unable
to tell which one of these two functions returned errors or
specifically what code was returned. This patch remedies that
situation by passing the return codes to err, which is returned by
mlx4_qp_attach_common() itself.
This also addresses a leak in the call to mlx4_bitmap_free() as well.
Signed-off-by: Robb Manes <rmanes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Frames destined to an unknown address must be forwarded to the CPU
port. Otherwise incoming ARP, dhcp leases, etc, do not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several functions can return negative value in case of error,
so their return type should be fixed as well as type of variables
to which this value is assigned.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Cc: stable@vger.kernel.org
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
|
|
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
|
|
Move pxamci to mmc slot-gpio API to fix interrupt request.
It fixes the case where the card detection is on a gpio expander, on I2C
for example on zylonite board. In this case, the card detect netsted
interrupt is called from a threaded interrupt. The request_irq() fails,
because a hard irq cannot be a nested interrupt from a threaded
interrupt (set __setup_irq()).
This was tested on zylonite and mioa701 boards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.
As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Fixes: 16b23787fc70 ("mmc: sdhci-of-arasan: Call OF parsing for MMC")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
|
|
The size of the MAC register dump used to be the size specified by the
reg property in the device tree. Userland has no good way of finding
out that size, and it was not specified consistently for each MAC type,
so ethtool would end up printing junk at the end of the register dump
if the device tree didn't match the size it assumed.
Using the new version numbers indicates unambiguously that the size of
the MAC register dump is dependent only on the MAC type.
Fixes: 5369c71f7ca2 ("net/ibm/emac: fix size of emac dump memory areas")
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's possible that while we are waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If we then attempt to use the queue, we will panic.
Add a check for this condition on the receive side. This matches
an existing check on the send queue side.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously to this patch, the hardware was removing
VLAN tags from the inner header of VXLAN packets. The
hardware configuration can be changed to leave the
packet alone since that is what the linux stack
expects for this type of VLAN in VXLAN packet.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If I2C is built as module, the iTCO watchdog driver must be built as module
as well. I2C_I801 must only be selected if I2C is configured.
This fixes the following build errors, seen if I2C=m and ITCO_WDT=y.
i2c-i801.c:(.text+0x2bf055): undefined reference to `i2c_del_adapter'
i2c-i801.c:(.text+0x2c13e0): undefined reference to `i2c_add_adapter'
i2c-i801.c:(.text+0x2c17bd): undefined reference to `i2c_new_device'
Fixes: 2a7a0e9bf7b3 ("watchdog: iTCO_wdt: Add support for TCO on Intel Sunrisepoint")
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Currently poweroff/halt results in a reboot on the Raspberry Pi.
The firmware uses the RSTS register to know which partiton to
boot from. The partiton value is spread into bits
0, 2, 4, 6, 8, 10. Partiton 63 is a special partition used by
the firmware to indicate halt.
The firmware made this change in 19 Aug 2013 and was matched
by the downstream commit:
Changes for new NOOBS multi partition booting from gsh
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Pull MIPS fixes from Ralf Baechle:
- Properly setup irq handling for ATH79 platforms
- Fix bootmem mapstart calculation for contiguous maps
- Handle little endian and older CPUs correct in BPF
- Fix console for Fulong 2E systems
- Handle FTLB correctly on R6 CPUs
- Fixes for CM, GIC and MAAR support code
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Initialise MAARs on secondary CPUs
MIPS: print MAAR configuration during boot
MIPS: mm: compile maar_init unconditionally
irqchip: mips-gic: Fix pending & mask reads for MIPS64 with 32b GIC.
irqchip: mips-gic: Convert CPU numbers to VP IDs.
MIPS: CM: Provide a function to map from CPU to VP ID.
MIPS: Fix FTLB detection for R6
MIPS: cpu-features: Add cpu_has_ftlb
MIPS: ATH79: Add irq chip ar7240-misc-intc
MIPS: ATH79: Set missing irq ack handler for ar7100-misc-intc irq chip
MIPS: BPF: Fix build on pre-R2 little endian CPUs
MIPS: BPF: Avoid unreachable code on little endian
MIPS: bootmem: Fix mapstart calculation for contiguous maps
MIPS: Fix console output for Fulong2e system
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux into pm-cpuidle
Pull an intel_idle update for v4.3 from Len Brown.
* 'cpuidle' of https://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
intel_idle: Skylake Client Support - updated
|
|
gic_handle_shared_int reads the GIC interrupt pending & mask registers
directly into a bitmap, which is defined as an array of unsigned longs.
The GIC pending registers may be 32 bits wide if the CM is older than
CM3, regardless of the bit width of the CPU, but for MIPS64 kernels
the unsigned longs in the bitmap will be 64 bits wide. In this case we
need to perform 2 x 32 bit reads per 64 bit unsigned long in order to
avoid missing interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11213/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Make use of the mips_cm_vp_id function to convert from Linux CPU numbers
to the VP IDs used by hardware, which are not identical in all systems.
Without doing so we map interrupts to incorrect VP(E)s.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11212/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomass Gleixner:
"A bugfix for the atmel aic5 irq chip driver which caches the wrong
data and thereby breaking resume"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/atmel-aic5: Use per chip mask caches in mask/unmask()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first real batch of fixes this release cycle. Nothing really
concerning, and diffstat is a bit inflated due to some DT contents
moving around on STi platforms.
There's a collection of them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in
QCOM SCM firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge
window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting
to see a few more users in the wild"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
ARM: dts: fix omap2+ address translation for pbias
firmware: qcom: scm: Add function stubs for ARM64
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
ARM: pxa: balloon3: Fix build error
ARM: dts: Fixup model name for HP t410 dts
ARM: dts: DRA7: fix a typo in ethernet
ARM: omap2plus_defconfig: make PCF857x built-in
ARM: dts: Use ti,pbias compatible string for pbias
ARM: OMAP5: Cleanup options for SoC only build
ARM: DRA7: Select missing options for SoC only build
ARM: OMAP2+: board-generic: Remove stale of_irq macros
ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
ARM: dts: am335x-phycore-som: Fix mpu voltage
...
|
|
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.3-rc cycle:
- Two more patches to fix most of the MMC regressions with the
PBIAS regulator changes. At least two MMC driver related issues
still seems to remain for omap3 legacy booting and omap4 duovero.
Note that the dts changes depend on a recent regulator fix, and
are based on the regulator commit now in mainline kernel
- Enable autoidle for am43xx clocks to prevent clocks from staying
always on
- Fix i2c5 pinctrl offsets for omap5-uevm
- Enable PCA953X as that's needed for HDMI to work on omap5
- Update phy supplies for beagle x15 beta board
- Use palmas-usb for on beagle x15 to start using the related
driver that recently got merged
* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: fix omap2+ address translation for pbias
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
regulator: pbias: program pbias register offset in pbias driver
ARM: omap2plus_defconfig: Enable MUSB DMA support
ARM: DRA752: Add ID detect for ES2.0
ARM: OMAP3: vc: fix 'or' always true warning
ARM: OMAP2+: Fix booting if no timer parent clock is available
ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- check the return value of platform_get_irq as signed int in xgene.
- skip adf_dev_restore on virtual functions in qat.
- fix double-free with backlogged requests in marvell_cesa"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: xgene - fix handling platform_get_irq
crypto: qat - VF should never trigger SBR on PH
crypto: marvell - properly handle CRYPTO_TFM_REQ_MAY_BACKLOG-flagged requests
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This includes a iser-target series from Jenny + Sagi @ Mellanox that
addresses the few remaining active I/O shutdown bugs, along with a
patch to support zero-copy for immediate data payloads that gives a
nice performance improvement for small block WRITEs.
Also included are some recent >= v4.2 regression bug-fixes. The most
notable is a RCU conversion regression for SPC-3 PR registrations, and
recent removal of obsolete RFC-3720 markers that introduced a login
regression bug with MSFT iSCSI initiators.
Thanks to everyone who has been testing + reporting bugs for v4.x"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Avoid OFMarker + IFMarker negotiation
target: Make TCM_WRITE_PROTECT failure honor D_SENSE bit
target: Fix target_sense_desc_format NULL pointer dereference
target: Propigate backend read-only to core_tpg_add_lun
target: Fix PR registration + APTPL RCU conversion regression
iser-target: Skip data copy if all the command data comes as immediate
iser-target: Change the recv buffers posting logic
iser-target: Fix pending connections handling in target stack shutdown sequnce
iser-target: Remove np_ prefix from isert_np members
iser-target: Remove unused variables
iser-target: Put the reference on commands waiting for unsol data
iser-target: remove command with state ISTATE_REMOVE
|
