Age | Commit message (Collapse) | Author |
|
First control messages to the stick timeouts very often due to probable
hw bug. Repeat first message few times if it fails as workaround.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Bug causes 2nd FE MPEG TS buffer size to be zero and therefore no picture
when 2nd FE was enabled. Configure correct buffer size also for 2nd FE.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The default case of the switch didn't unlock the mutex.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
paging request at ffffffff
I'm using a "Hauppauge WinTV-NOVA-T DVB card" of PCI id "13c2:1005" with
kernel 2.6.27.9.
I've recently experienced the following fairly consistent kernel oops on
startup in grundig_29504_401_tuner_set_params from budget.c. As you
might expect, following this failure, the card doesn't work.
I'm not a kernel developer, nevertheless I seem to have managed to track
this down to a non-existent initialisation of
budget->dvb_frontend->tuner_priv.
The attached patch fixes the problem for me (and I've managed to tune
the card successfully as a result), but I don't know of anyone else
using the driver so I can't test it on other people.
Please let me know if this works for you or if I've done something
terribly wrong ;-(
BUG: unable to handle kernel paging request at ffffffff
IP: [<f8981e11>] :budget:grundig_29504_401_tuner_set_params+0x3b/0xf8
*pde = 007e0067 *pte = 00000000
Oops: 0000 [#1] SMP
Modules linked in: bridge stp bnep rfcomm l2cap asb100 hwmon_vid hwmon
fuse ipt_REJECT nf_conntrack_ipv4 iptable_filter ip_tables ip6t_REJECT
xt_tcpudp nf_conntrack_ipv6 xt_state nf_conntrack ip6table_filter
ip6_tables x_tables ipv6 loop dm_multipath scsi_dh ppdev snd_cmipci
gameport snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq
snd_pcm_oss snd_mixer_oss l64781 snd_pcm snd_page_alloc snd_opl3_lib
snd_timer parport_pc snd_hwdep parport btusb snd_mpu401_uart budget
budget_core snd_rawmidi bluetooth saa7146 snd_seq_device ttpci_eeprom
snd soundcore sr_mod i2c_sis96x cdrom dvb_core sis900 i2c_core floppy
pcspkr mii sata_sil sg dm_snapshot dm_zero dm_mirror dm_log dm_mod
pata_sis ata_generic pata_acpi libata sd_mod scsi_mod crc_t10dif ext3
jbd mbcache uhci_hcd ohci_hcd ehci_hcd [last unloaded: microcode]
Pid: 2319, comm: kdvb-fe-0 Not tainted (2.6.27.9-73.fc9.i686 #1)
EIP: 0060:[<f8981e11>] EFLAGS: 00010286 CPU: 0
EIP is at grundig_29504_401_tuner_set_params+0x3b/0xf8 [budget]
EAX: f6417f00 EBX: f6f53808 ECX: 00000000 EDX: ffffffff
ESI: f6f94404 EDI: f6417f00 EBP: f6417f10 ESP: f6417ef0
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process kdvb-fe-0 (pid: 2319, ti=f6417000 task=f642b2c0 task.ti=f6417000)
Stack: f6e39800 00000000 00000004 f6417f00 c064523c f6f53808 f6f53800 f6f94404
f6417f54 f8b2e45a f6417f24 00000286 f6417f4c f6417f38 00000000 00000286
f6417f3c c064520f f642b2c0 f6417f6c c064456f 00000001 f6f94400 00000001
Call Trace:
[<c064523c>] ? _spin_lock_irqsave+0x29/0x30
[<f8b2e45a>] ? apply_frontend_param+0x27/0x357 [l64781]
[<c064520f>] ? _spin_lock_irq+0x1c/0x20
[<c064456f>] ? __down_common+0x91/0xbf
[<f894f25d>] ? dvb_frontend_swzigzag_autotune+0x17d/0x1a4 [dvb_core]
[<f894f780>] ? dvb_frontend_swzigzag+0x1ac/0x209 [dvb_core]
[<f894fcc8>] ? dvb_frontend_thread+0x2eb/0x3b3 [dvb_core]
[<c043c166>] ? autoremove_wake_function+0x0/0x33
[<f894f9dd>] ? dvb_frontend_thread+0x0/0x3b3 [dvb_core]
[<c043bec3>] ? kthread+0x3b/0x61
[<c043be88>] ? kthread+0x0/0x61
[<c040494b>] ? kernel_thread_helper+0x7/0x10
=======================
Code: ec 14 8b 80 00 02 00 00 8b 93 08 02 00 00 8d 7d e4 8b 40 20 89 45
e0 31 c0 85 d2 f3 ab 8d 45 f0 66 c7 45 e8 04 00 89 45 ec 74 09 <0f> b6
02 66 89 45 e4 eb 06 66 c7 45 e4 61 00 8b 0e be 0a 8b 02
EIP: [<f8981e11>] grundig_29504_401_tuner_set_params+0x3b/0xf8 [budget]
SS:ESP 0068:f6417ef0
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Revert a change made in change 9743 which resulted in a kernel panic in some
cases on shutdown of the audio stream.
First discovered when working on the Pinnacle 880e support, and later
reproduced by a user on the mailing list with the HVR-900 as well.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix for KWorld 330U Board
Many thanks to Devin and Mauro!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix for KWorld 330U AC97
Many thanks to Devin and Mauro again!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx: Fix audio URB transfer buffer memory leak and race
condition/corruption of capture pointer
Leak fix kindly contributed by Pádraig Brady.
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
With the conversion to v4l2_subdev one bit of code was accidentally dropped:
on receiving the first command the driver has to load the fw. A new init()
command was introduced to do that explicitly for bridge drivers that are
converted to use v4l2_subdev, but old drivers that are not yet converted
no longer worked.
This patch fixes this regression for these old drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The VIDIOC_QUERYCTRL command needs to actually do a queryctrl, not a
querymenu. Similarly, the VIDIOC_QUERYMENU command needs to actually
do a querymenu not a queryctrl.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The following patch adds support for a new version of the
Terratec Cinergy DT USB XS Diversity Dual DVB-T TV tuner stick.
The USB ID of the new stick is 0ccd:0081.
The hardware of the stick has changed, when compared to the first version of
this stick, but it still uses quite standard components, so that only minor
changes are needed to the sources.
The patch has been successfully tested with hotplugging the device and then
2 x tzap and 2 x mplayer, to watch two different TV programs simultaneously.
The stick works with both, the old and new firmwares:
- dvb-usb-dib0700-1.10.fw and
- dvb-usb-dib0700-1.20.fw
Signed-off-by: Nicolas Fournier <nicolasfournier@yahoo.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
On Fri, 2009-01-09 at 15:40 +0300, Goga777 wrote:
> hI
>
> With today v4l-dvb I couldn't run my hvr4000 card on 2.6.27 kernel
> [ 14.555162] cx88/2: cx2388x dvb driver version 0.0.6 loaded
> [ 14.555231] cx88/2: registering cx8802 driver, type: dvb access: shared
> [ 14.555303] cx88[0]/2: subsystem: 0070:6900, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=68]
> [ 14.555374] cx88[0]/2: cx2388x based DVB/ATSC card
> [ 14.555446] BUG: unable to handle kernel NULL pointer dereference at 00000000
> [ 14.555560] IP: [<c02e6bff>] __mutex_lock_common+0x3c/0xe4
> [ 14.555652] *pde = 00000000
> [ 14.555735] Oops: 0002 [#1] SMP
> [ 14.555851] Modules linked in: cx88_dvb(+) cx88_vp3054_i2c videobuf_dvb wm8775 dvb_core tuner_simple tuner_types snd_seq_dummy tda9887 snd_seq_oss(+) snd_intel8x0(+) tda8290 snd_seq_midi snd_seq_midi_event snd_ac97_codec cx88_alsa(+) snd_seq ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_rawmidi snd_timer tuner snd_seq_device psmouse snd serio_raw ivtv(+) cx8800 cx8802 cx88xx soundcore cx2341x ir_common ns558 i2c_i801 v4l2_common videodev i2c_algo_bit gameport v4l1_compat snd_page_alloc tveeprom pcspkr floppy videobuf_dma_sg videobuf_core btcx_risc i2c_core parport_pc parport button intel_agp agpgart shpchp pci_hotplug rng_core iTCO_wdt sd_mod evdev usbhid hid ff_memless ext3 jbd mbcache ide_cd_mod cdrom ide_disk ata_piix libata dock 8139too usb_storage scsi_mod piix 8139cp mii ide_core uhci_hcd ehci_hcd usbcore thermal processor fan thermal_sys
> [ 14.557013]
> [ 14.557013] Pid: 2310, comm: modprobe Not tainted (2.6.27.1-custom-default1 #1)
> [ 14.557013] EIP: 0060:[<c02e6bff>] EFLAGS: 00010246 CPU: 1
> [ 14.557013] EIP is at __mutex_lock_common+0x3c/0xe4
> [ 14.557013] EAX: de653e98 EBX: de739118 ECX: de739120 EDX: 00000000
> [ 14.557013] ESI: dd4209e0 EDI: de73911c EBP: de653eb0 ESP: de653e88
> [ 14.557013] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
> [ 14.557013] Process modprobe (pid: 2310, ti=de652000 task=dd4209e0 task.ti=de652000)
> [ 14.557013] Stack: 3535352e 5d343733 00000002 de739120 de739120 00000000 c044a6c0 de739110
> [ 14.557013] de739118 00000001 de653ebc c02e6d38 c02e6b88 de653ec4 c02e6b88 de653ed8
> [ 14.557013] e1ac7115 de6a9000 00000001 00000000 de653f0c e1aeca62 de739004 de739000
> [ 14.557013] Call Trace:
> [ 14.557013] [<c02e6d38>] ? __mutex_lock_slowpath+0x17/0x1a
> [ 14.557013] [<c02e6b88>] ? mutex_lock+0x12/0x14
> [ 14.557013] [<c02e6b88>] ? mutex_lock+0x12/0x14
> [ 14.557013] [<e1ac7115>] ? videobuf_dvb_get_frontend+0x19/0x40 [videobuf_dvb]
> [ 14.557013] [<e1aeca62>] ? cx8802_dvb_probe+0xc9/0x1945 [cx88_dvb]
> [ 14.557013] [<e09ee41e>] ? cx8802_register_driver+0xbd/0x1ac [cx8802]
> [ 14.557013] [<e09ee467>] ? cx8802_register_driver+0x106/0x1ac [cx8802]
> [ 14.557013] [<e1aee37f>] ? dvb_init+0x22/0x27 [cx88_dvb]
> [ 14.557013] [<c0101132>] ? _stext+0x42/0x11a
> [ 14.557013] [<e1aee35d>] ? dvb_init+0x0/0x27 [cx88_dvb]
> [ 14.557013] [<c013d2ca>] ? __blocking_notifier_call_chain+0xe/0x51
> [ 14.557013] [<c014970b>] ? sys_init_module+0x8c/0x17d
> [ 14.557013] [<c0103b42>] ? syscall_call+0x7/0xb
> [ 14.557013] [<c013007b>] ? round_jiffies_relative+0x14/0x16
> [ 14.557013] =======================
> [ 14.557013] Code: 78 04 89 f8 89 55 e0 64 8b 35 00 30 3f c0 e8 2e 0c 00 00 8d 43 08 89 45 e4 8b 53 0c 8d 45 e8 8b 4d e4 89 43 0c 89 4d e8 89 55 ec <89> 02 89 75 f0 83 c8 ff 87 03 48 74 55 8a 45 e0 8b 4d e0 83 e0
> [ 14.557013] EIP: [<c02e6bff>] __mutex_lock_common+0x3c/0xe4 SS:ESP 0068:de653e88
> [ 14.565211] ---[ end trace 94d8b014e067ac7b ]---
Tested and confirmed to work by several users at linux-media@vger.kernel.org
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Some em28xx devices use the PCM IN AC 97 PIN for digital audio. However,
currently, the PCM IN selection is not set by the driver. This patch allows
specifying the PCM IN expected output, via board description table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The zoran driver does a module_get/put of THIS_MODULE on device open/close.
This isn't necessary as the kernel does this automatically.
Clean up the failure path of zoran_open() somewhat.
Make the dprintk()s on open/close a higher debug level and make the user
count printed take the current open/close into account.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The driver should only use the kernel mapped io address, zr36057_mem, and
not the PCI bus address, zr36057_adr. Since the latter is only printed out
once, there is no need to save it in the driver data structure.
There was some old code that looked like it was for the Alpha architecture
which would use the PCI bus address. It probably no longer applies to
modern kernels.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Instead of using custom code, just let the device layer look it up for us
from the pci device table. This requires extending the pci device table to
list each known card, plus a catch-all entry for the cards that don't have
sub-system vendor/device data.
Improve some of the info and error messages too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The driver was keeping a global array with an entry for each zoran device
probed. It was a leftover from when the driver didn't dynamically allocate
the driver data for each device.
There was only one use left, in the video device's ->open() method, looking
up the struct zoran for the opened device from the minor number. This can
be done better with video_get_drvdata().
Since zoran_num is now only used in the pci driver's ->probe() method, it
doesn't need to be an atomic_t and be static. There is a race if multiple
zoran cards could be probed at the same time, but currently the probe
method for a given driver is single threaded.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When initializing a module parameter that is a per-card array, use
"{ [0 ... (BUZ_MAX-1)] = -1 }" instead of "{ -1, -1, -1, -1 }". This way
all of the entries will be correctly set to -1 if someone changes BUZ_MAX
to a value other than 4.
Adjust some of the parameter help text too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
interrupts
When enabling a shared IRQ line, then saa7134_irq handler could be invoked
before the driver had completely set up internal structures, due to a shared
interrupt line firing. Clear the saa7134 interrupt status reg, before
requesting the irq line, so that stale IRQ status isn't processed before the
internal structures are set up.
Marcin Slusarz recently brought this Oops to the attention of the v4l-dvb
lists and provided an initial analysis by investigating reports found here:
http://kerneloops.org/guilty.php?guilty=mute_input_7133&version=2.6.27-release&start=1802240&end=1835007&class=oops
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
only cards
Analog support for HVR-1250 has not been completed, but does exist for
the HVR-1800.
Since both cards use the same driver, it tries to create the analog
dev for both devices, which is not possible.
This causes a NULL error to show up in video_open and mpeg_open.
-Mark
Iterations through the cx23885_devlist must check for NULL
pointers as some supported devices only have DVB support at the moment.
Mark Jenks encoutered an Oops in a system with both an HVR-1250 and HVR-1800
installed.
-Andy
Reported-by: Mark Jenks <mjenks1968@gmail.com>
Tested-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Register 0x2d has to be set differently in the saa7129 compared to the
saa7127. This was not done correctly, so S-Video was broken in certain
circumstances.
This fixes a regression introduced in 2.6.28.
Signed-off-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is a really old and crufty driver that wasn't using the long
established pci driver framework.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
[mchehab@redhat.com: Cleaned up a few CodingStyle issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If Hauppauge eeprom is corrupted, the driver returns tuner = 0, instead
of TUNER_ABSENT.
This makes the drivers to initialize tuner, instead of handling the
manual parameter.
Since the tuner core rejects that a tuner to have their type changed,
this breaks the manual tuner override.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Changeset 60b4bde48b36c0315ef41fd38c339b9c7e68c46f removed an unused
struct on zoran driver, when compiled with "Y".
However, as pointed by Jean Delvare <khali@linux-fr.org>, this is
neeeded when the driver is compiled as a module, since udev relies on it
to auto-load the module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Concurrent access to a single DVB CA 50221 interface slot is generally
discouraged. The underlying drivers (budget-av, budget-ci) do not implement
proper locking and thus two transactions could (and do) interfere with on
another.
This fixes the following problems seen by others and myself:
- sudden i/o errors when writing to the ci device which usually would
result in an undefined state of the hw and require a software restart
- errors about the CAM trying to send a buffer larger than the agreed size
usually also resulting in an undefined state of the hw
Due the to design of the DVB CA 50221 driver, implementing the locks in the
underlying drivers would not be enough and still leave some race conditions,
even though they were harder to trigger.
Signed-off-by: Matthias Dahl <devel@mortal-soul.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
to avoid:
| tvp514x 0-005c: No platform data
| !!<3>tvp514x 0-005d: No platform data
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Randy Dunlap <randy.dunlap@oracle.com> wrote:
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c: In function 'cx88_call_i2c_clients':
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:122: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:123: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:127: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:128: error: 'struct cx88_core' has no member named 'gate_ctrl'
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Commit 44f0079ec74330b457d990072c13cbe28b0f1abf erroneously considers all
GET_DEF requests as unsuccessful. Fix this by checking the request return
value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The UVC specification release number is a binary-coded decimal number, print
it as such.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch introduces support for dvb-t for the following dibcom based card:
Terratec Cinergy T Express (USB-ID: 0ccd:0062)
Signed-off-by: Yusuf Altin <yusuf.altin@t-online.de>
Signed-off-by: Albert Comerma <albert.comerma@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Removed unused #include <version.h>'s in files below,
drivers/media/video/cs5345.c
drivers/media/video/pwc/pwc-if.c
drivers/media/video/saa717x.c
drivers/media/video/upd64031a.c
drivers/media/video/upd64083.c
drivers/media/video/uvc/uvc_ctrl.c
drivers/media/video/uvc/uvc_driver.c
drivers/media/video/uvc/uvc_queue.c
drivers/media/video/uvc/uvc_video.c
drivers/media/video/uvc/uvc_status.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx were trying to access the third input entry, even for boards that
don't support it.
This patch reviews the input mux selection fixing this bug and a few
other troubles, like not validating the input on one userspace ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
|
|
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
|
|
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.
Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds a new device id
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|