Age | Commit message (Collapse) | Author |
|
Bartek reported that after few cable unplug/replug cycles suddenly
replug isn't detected any longer. His system uses a RTL8106, I wasn't
able to reproduce the issue with RTL8168g. According to his bisect
the referenced commit caused the regression. As Realtek doesn't
release datasheets or errata it's hard to say what's the actual root
cause, but this change was reported to fix the issue.
Fixes: 38caff5a445b ("r8169: handle all interrupt events in the hard irq handler")
Reported-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Suggested-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Tested-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ti/netcp_ethss.c:3661:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
./drivers/net/ethernet/ti/netcp_ethss.c:3665:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to ehea_get_eth_dn returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ibm/ehea/ehea_main.c:3163:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3154, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Douglas Miller <dougmill@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the original patch network starts to crash on heavy load.
It's not fully clear why this additional register read has such side
effects, but removing it fixes the issue.
Thanks also to Alex for his contribution and hints.
[0] https://marc.info/?t=155268170400002&r=1&w=2
Fixes: e782410ed237 ("r8169: improve spurious interrupt detection")
Reported-by: VDR User <user.vdr@gmail.com>
Tested-by: VDR User <user.vdr@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When there is only one byte in a frag, the current calculation
using "(size + HNS3_MAX_BD_SIZE - 1) >> HNS3_MAX_BD_SIZE_OFFSET"
will return zero, because HNS3_MAX_BD_SIZE is 65535 and
HNS3_MAX_BD_SIZE_OFFSET is 16. So it will cause tx error when
a frag's size is one byte.
This patch fixes it by using DIV_ROUND_UP.
Fixes: 3fe13ed95dd3 ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both PCLK and HCLK are "required" clocks according to macb devicetree
documentation. There is a chance that devm_clk_get doesn't return a
negative error but just a NULL clock structure instead. In such a case
the driver proceeds as usual and uses pclk value 0 to calculate MDC
divisor which is incorrect. Hence fix the same in clock initialization.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we don't try to enqueue XDP_REDIRECT frames to an
inexistent FQ.
While it is guaranteed not to have more than one queue per core,
having fewer queues than CPUs on an interface is a valid
configuration.
Fixes: d678be1dc1ec ("dpaa2-eth: add XDP_REDIRECT support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or
with a so-called non-PCI interface (KSZ8851-16MLL). When the driver
for the latter was introduced with commit a55c0a0ed415 ("drivers/net:
ks8851_mll ethernet network driver"), it duplicated the register macros
introduced by the driver for the former with commit 3ba81f3ece3c ("net:
Micrel KS8851 SPI network driver").
The chips are almost identical, so the duplication seems unwarranted.
There are a handful of bits which are in use on the KSZ8851-16MLL but
reserved on the KSZ8851SNL, and vice-versa, but there are no actual
collisions.
Thus, remove the duplicate definitions from the KSZ8851-16MLL driver.
Mark all bits which differ between the two chips. Move the SPI frame
opcodes, which are specific to KSZ8851SNL, to its driver.
The KSZ8851-16MLL driver added a RXFCTR_THRESHOLD_MASK macro which is a
duplication of the RXFCTR_RXFCT_MASK macro, rename it where it's used.
Same for P1MBCR_FORCE_FDX, which duplicates the BMCR_FULLDPLX macro and
OBCR_ODS_16MA, which duplicates OBCR_ODS_16mA.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the header file accompanying the ks8851 driver, the P1SCLMD register
macros are misnamed, they actually pertain to the P1CR register.
The P1CR macros in turn pertain to the P1SR register, see pages 65 to 68
of the spec:
http://www.hqchip.com/uploads/pdf/201703/47c98946d6c97a4766e14db3f24955f2.pdf
The misnomers have no negative consequences so far because the macros
aren't used by ks8851.c, but that's about to change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.
The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.
The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver currently requests the IRQ before registering the
net_device. Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present. Most other drivers delay
requesting the IRQ until the net_device is opened. Do the same.
The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.
However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").
However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management: On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.
The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.
Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.
The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status
[...]
1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e
^^^^^^^^^^^^^^^^^^^^^
2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e
^^^^^^^^^^^^^^^^^^^^^
A simple ping test will now report bad data:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recently added function in mlxsw triggers a harmless compiler warning:
In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17,
from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7:
drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get':
drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
#define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125)
~~~~~^~~~~~
drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC'
if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) {
^~~~~~~~~~~~~~~~~~~~~~~~~
The warning is normally disabled, but it would be nice to enable
it to find real bugs, and there are no other known instances at
the moment.
Replace the negation with a zero-comparison, which also matches
the comment above it.
Fixes: d93c19a1d95c ("mlxsw: core: Add API for QSFP module temperature thresholds reading")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
First set of fixes for 5.1. Lots of fixes for mt76 this time.
iwlwifi
* fix warning with do_div()
mt7601u
* avoid using hardware which is supported by mt76
mt76
* more fixes for hweight8() usage
* fix hardware restart for mt76x2
* fix writing txwi on USB devices
* fix (and disable by default) ED/CCA support on 76x2
* fix powersave issues on 7603
* fix return value check for ioremap on 7603
* fix duplicate USB device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My commit 26a7b5473191 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).
Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.
Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.
Fixes: 26a7b5473191 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix following schedule while atomic in mt76x02_reset_state
since synchronize_rcu is run inside a RCU section
[44036.944222] mt76x2e 0000:06:00.0: MCU message 31 (seq 3) timed out
[44036.944281] BUG: sleeping function called from invalid context at kernel/rcu/tree_exp.h:818
[44036.944284] in_atomic(): 1, irqs_disabled(): 0, pid: 28066, name: kworker/u4:1
[44036.944287] INFO: lockdep is turned off.
[44036.944292] CPU: 1 PID: 28066 Comm: kworker/u4:1 Tainted: G W 5.0.0-rc7-wdn-t1+ #7
[44036.944294] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009
[44036.944305] Workqueue: phy1 mt76x02_wdt_work [mt76x02_lib]
[44036.944308] Call Trace:
[44036.944317] dump_stack+0x67/0x90
[44036.944322] ___might_sleep.cold.88+0x9f/0xaf
[44036.944327] rcu_blocking_is_gp+0x13/0x50
[44036.944330] synchronize_rcu+0x17/0x80
[44036.944337] mt76_sta_state+0x138/0x1d0 [mt76]
[44036.944349] mt76x02_wdt_work+0x1c9/0x610 [mt76x02_lib]
[44036.944355] process_one_work+0x2a5/0x620
[44036.944361] worker_thread+0x35/0x3e0
[44036.944368] kthread+0x11c/0x140
[44036.944376] ret_from_fork+0x3a/0x50
[44036.944384] BUG: scheduling while atomic: kworker/u4:1/28066/0x00000002
[44036.944387] INFO: lockdep is turned off.
[44036.944389] Modules linked in: cmac ctr ccm af_packet snd_hda_codec_hdmi
Introduce __mt76_sta_remove in order to run sta_remove without holding dev->mutex.
Move __mt76_sta_remove outside of RCU section in mt76x02_reset_state
Fixes: e4ebb8b403d1 ("mt76: mt76x2: implement full device restart on watchdog reset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since some USB device IDs are duplicated between mt7601u and mt76x0u
devices, check chip version on probe and return error if not match
0x7601.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not mt7601u device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
|
|
As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.
Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.
Fixes: dc149e3764d8 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.
Fixes: ebccc7397e4a ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device ID alone does not uniquely identify a device. Test both the
vendor and device ID to make sure we don't mistakenly think some other
vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex
ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device
ID table.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit ad6c9986bcb62 ("vxlan: Fix GRO cells race condition between
receive and link delete") fixed a race condition for the typical case a vxlan
device is dismantled from the current netns. But if a netns is dismantled,
vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue()
of all the vxlan tunnels that are related to this netns.
In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before
unregister_netdevice_queue(). This means that the gro_cells_destroy() call is
done too soon, for the same reasons explained in above commit.
So we need to fully respect the RCU rules, and thus must remove the
gro_cells_destroy() call or risk use after-free.
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer")
Signed-off-by: Suanming.Mou <mousuanming@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP/UDP checksum validity was propagated to skb
only if IP checksum is valid.
But for IPv6 there is no validity as there is no checksum in IPv6.
This patch propagates TCP/UDP checksum validity regardless of IP checksum.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 2964db0f5904 ("m68k: Mac DP8390 update")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to commit a7603ac1fc8c ("geneve: change NET_UDP_TUNNEL
dependency to select"), GTP has a dependency on NET_UDP_TUNNEL which
makes impossible to compile it if no other protocol depending on
NET_UDP_TUNNEL is selected.
Fix this by changing the depends to a select, and drop NET_IP_TUNNEL from
the select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In my latest patch I missed one rcu_read_unlock(), in case
device is down.
Fixes: 4477138fa0ae ("tun: properly test for IFF_UP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Same reasons than the ones explained in commit 4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")
netif_rx_ni() or napi_gro_frags() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
A similar protocol is used for gro layer.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Fixes: 1bd4978a88ac ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an interrupt is already pending when the interrupt is enabled on the
GXL phy, no IRQ will ever be triggered.
The fix is simply to make sure pending IRQs are cleared before setting
up the irq mask.
Fixes: cf127ff20af1 ("net: phy: meson-gxl: add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several statements that contain extra spacing in
the indentation; clean this up by removing spaces. Also
add { } braces on if statement to keep to kernel coding
style.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a statement that is indented incorrectly; replace
spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_alloc_skb can fail and return a NULL pointer which is
dereferenced without a check. The patch avoids such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending non-linear skbs with jumbo frames, we set up the non-paged
data and mark that as a last segment, although the paged fragments are
also prepared. This will stall the TX queue and trigger a watchdog warning
(a simple reproducer is to run an iperf client mode TCP test with a large
MTU - networking fails instantly).
Fix by checking if the skb is non-linear.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit
routine") overlooked jumbo frames when re-ordering the code, and as a
result the own bit was not getting set anymore for the first jumbo frame
descriptor. Commit 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo
frames") tried to fix this, but now the bit is getting set too early and
the DMA may start while we are still setting up the remaining descriptors.
And with the chain mode the own bit remains still unset.
Fix by setting the own bit at the end of xmit also with jumbo frames.
Fixes: 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit routine")
Fixes: 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo frames")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc patches from Andrew Morton:
- a little bit more MM
- a few fixups
[ The "little bit more MM" is actually just one of the three patches
Andrew sent for mm/filemap.c, I'm still mulling over two more of them
from Josef Bacik - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
include/linux/swap.h: use offsetof() instead of custom __swapoffset macro
tools/testing/selftests/proc/proc-pid-vm.c: test with vsyscall in mind
zram: default to lzo-rle instead of lzo
filemap: pass vm_fault to the mmap ra helpers
|
|
lzo-rle gives higher performance and similar compression ratios to lzo.
Link: http://lkml.kernel.org/r/20190205155944.16007-4-dave.rodgman@arm.com
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These fix a couple of issues and do some cleanups on top of the
previous ACPI changes for 5.1-rc1.
Specifics:
- Fix a crash caused by unloading an SSDT overlay (Andy Shevchenko)
- Prevent user space from getting confusing error values on failing
ACPI sysfs accesses (Rafael Wysocki)
- Simplify leaf node detection in the PPTT parsing code by using a
new flag defined in ACPI 6.3 (Jeremy Linton)
- Add missing "static" in some places in the ACPI configfs code (Andy
Shevchenko)
- Fix acpidbg tool path in the ACPI documentation (Flavio Suligoi)"
* tag 'acpi-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sysfs: Prevent get_status() from returning acpi_status
ACPI / device_sysfs: Avoid OF modalias creation for removed device
ACPI / configfs: Mark local data structures static
ACPI / configfs: Mark local functions static
ACPI: tables: Simplify PPTT leaf node detection
ACPI: Documentation: Fix path for acpidbg tool
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups on top of the previously merged
power management material for 5.1-rc1 with one cpupower utility update
that wasn't pushed earlier due to unfortunate timing.
Specifics:
- Fix registration of new cpuidle governors partially broken during
the 5.0 development cycle by mistake (Rafael Wysocki).
- Avoid integer overflows in the menu cpuidle governor by making it
discard the overflowing data points upfront (Rafael Wysocki).
- Fix minor mistake in the recent update of the iowait boost
computation in the intel_pstate driver (Rafael Wysocki).
- Drop incorrect __init annotation from one function in the pxa2xx
cpufreq driver (Arnd Bergmann).
- Fix the operating performance points (OPP) framework initialization
for devices in multiple power domains if only one of them is
scalable (Rajendra Nayak).
- Fix mistake in dev_pm_opp_set_rate() which causes it to skip
updating the performance state if the new frequency is the same as
the old one (Viresh Kumar).
- Rework the cancellation of wakeup source timers to avoid potential
issues with it and do some cleanups unlocked by that change (Viresh
Kumar, Rafael Wysocki).
- Clean up the code computing the active/suspended time of devices in
the PM-runtime framework after recent changes (Ulf Hansson).
- Make the power management infrastructure code use pr_fmt()
consistently (Joe Perches).
- Clean up the generic power domains (genpd) framework somewhat
(Aisheng Dong).
- Improve kerneldoc comments for two functions in the cpufreq core
(Rafael Wysocki).
- Fix typo in a PM QoS file description comment (Aisheng Dong).
- Update the handling of CPU boost frequencies in the cpupower
utility (Abhishek Goel)"
* tag 'pm-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: governor: Add new governors to cpuidle_governors again
cpufreq: intel_pstate: Fix up iowait_boost computation
PM / OPP: Update performance state when freq == old_freq
PM / wakeup: Drop wakeup_source_drop()
PM / wakeup: Rework wakeup source timer cancellation
PM / domains: Remove one unnecessary blank line
PM / Domains: Return early for all errors in _genpd_power_off()
PM / Domains: Improve warn for multiple states but no governor
OPP: Fix handling of multiple power domains
PM / QoS: Fix typo in file description
cpufreq: pxa2xx: remove incorrect __init annotation
PM-runtime: Call pm_runtime_active|suspended_time() from sysfs
PM-runtime: Consolidate code to get active/suspended time
PM: Add and use pr_fmt()
cpufreq: Improve kerneldoc comments for cpufreq_cpu_get/put()
cpuidle: menu: Avoid overflows when computing variance
tools/power/cpupower: Display boost frequency separately
|
|
Pull networking fixes from David Miller:
"More fixes in the queue:
1) Netfilter nat can erroneously register the device notifier twice,
fix from Florian Westphal.
2) Use after free in nf_tables, from Pablo Neira Ayuso.
3) Parallel update of steering rule fix in mlx5 river, from Eli
Britstein.
4) RX processing panic in lan743x, fix from Bryan Whitehead.
5) Use before initialization of TCP_SKB_CB, fix from Christoph Paasch.
6) Fix locking in SRIOV mode of mlx4 driver, from Jack Morgenstein.
7) Fix TX stalls in lan743x due to mishandling of interrupt ACKing
modes, from Bryan Whitehead.
8) Fix infoleak in l2tp_ip6_recvmsg(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
pptp: dst_release sk_dst_cache in pptp_sock_destruct
MAINTAINERS: GENET & SYSTEMPORT: Add internal Broadcom list
l2tp: fix infoleak in l2tp_ip6_recvmsg()
net/tls: Inform user space about send buffer availability
net_sched: return correct value for *notify* functions
lan743x: Fix TX Stall Issue
net/mlx4_core: Fix qp mtt size calculation
net/mlx4_core: Fix locking in SRIOV mode when switching between events and polling
net/mlx4_core: Fix reset flow when in command polling mode
mlxsw: minimal: Initialize base_mac
mlxsw: core: Prevent duplication during QSFP module initialization
net: dwmac-sun8i: fix a missing check of of_get_phy_mode
net: sh_eth: fix a missing check of of_get_phy_mode
net: 8390: fix potential NULL pointer dereferences
net: fujitsu: fix a potential NULL pointer dereference
net: qlogic: fix a potential NULL pointer dereference
isdn: hfcpci: fix potential NULL pointer dereference
Documentation: devicetree: add a new optional property for port mac address
net: rocker: fix a potential NULL pointer dereference
net: qlge: fix a potential NULL pointer dereference
...
|
|
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
|
|
Pull remoteproc updates from Bjorn Andersson:
"This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs"
* tag 'rproc-v5.1' of git://github.com/andersson/remoteproc: (33 commits)
remoteproc: fix for "dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag"
remoteproc: fix rproc_check_carveout_da() returned error and comments
remoteproc: fix trace buffer va initialization
remoteproc: fix rproc_alloc_carveout() for rproc with iommu domain
remoteproc: add warning on resource table cast
remoteproc: fix rproc_alloc_carveout() bad variable cast
remoteproc: fix rproc_da_to_va in case of unallocated carveout
remoteproc: correct rproc_mem_entry_init() comments
remoteproc: fix recovery procedure
rpmsg: virtio: change header file sort style
rpmsg: virtio: allocate buffer from parent
remoteproc: st: add reserved memory support
remoteproc: create vdev subdevice with specific dma memory pool
remoteproc: q6v5_adsp: Remove voting for lpass_aon clock
dt-binding: remoteproc: Remove lpass_aon clock from adsp pil clock list
remoteproc: q6v5-mss: Active powerdomain for SDM845
remoteproc: q6v5-mss: Vote for rpmh power domains
remoteproc: qcom: Add support for parsing fw dt bindings
remoteproc: qcom_q6v5: don't auto boot remote processor
remoteproc: qcom: Wait for shutdown-ack/ind on sysmon shutdown
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
|