Age | Commit message (Collapse) | Author |
|
This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.
If you need this flag to be persisted across reboots, it's suggested
to use a udev rule to call adjust it until the kernel could have your
configuration in a disallow list.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
commit e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME
systems") disabled s0ix flows for systems that have various incarnations of
the i219-LM ethernet controller. This changed caused power consumption
regressions on the following shipping Dell Comet Lake based laptops:
* Latitude 5310
* Latitude 5410
* Latitude 5410
* Latitude 5510
* Precision 3550
* Latitude 5411
* Latitude 5511
* Precision 3551
* Precision 7550
* Precision 7750
This commit was introduced because of some regressions on certain Thinkpad
laptops. This comment was potentially caused by an earlier
commit 632fbd5eb5b0e ("e1000e: fix S0ix flows for cable connected case").
or it was possibly caused by a system not meeting platform architectural
requirements for low power consumption. Other changes made in the driver
with extended timeouts are expected to make the driver more impervious to
platform firmware behavior.
Fixes: e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME systems")
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Per guidance from Intel ethernet architecture team, it may take
up to 1 second for unconfiguring ULP mode.
However in practice this seems to be taking up to 2 seconds on
some Lenovo machines. Detect scenarios that take more than 1 second
but less than 2.5 seconds and emit a warning on resume for those
scenarios.
Suggested-by: Aaron Ma <aaron.ma@canonical.com>
Suggested-by: Sasha Netfin <sasha.neftin@intel.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
CC: Mark Pearson <markpearson@lenovo.com>
Fixes: f15bb6dde738cc8fa0 ("e1000e: Add support for S0ix")
BugLink: https://bugs.launchpad.net/bugs/1865570
Link: https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20200323191639.48826-1-aaron.ma@canonical.com/
Link: https://lkml.org/lkml/2020/12/13/15
Link: https://lkml.org/lkml/2020/12/14/708
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If the shutdown failed, the part will be thawed and running
S0ix flows will put it into an undefined state.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- A series from Prashant for Type-C to implement TYPEC_STATUS,
parsing USB PD Partner ID VDOs, and registering partner altmodes.
cros_ec misc:
- Don't treat RTC events as wakeup sources in cros_ec_proto"
* tag 'tag-chrome-platform-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_typec: Tolerate unrecognized mux flags
platform/chrome: cros_ec_typec: Register partner altmodes
platform/chrome: cros_ec_typec: Parse partner PD ID VDOs
platform/chrome: cros_ec_typec: Introduce TYPEC_STATUS
platform/chrome: cros_ec: Import Type C host commands
platform/chrome: cros_ec_typec: Clear partner identity on device removal
platform/chrome: cros_ec_typec: Fix remove partner logic
platform/chrome: cros_ec_typec: Relocate set_port_params_v*() functions
platform/chrome: Don't treat RTC events as wakeup sources
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Removal of the pnx83xx driver
- Add a binding for A100's watchdog controller
- Add Rockchip compatibles to snps,dw-wdt.yaml
- hpwdt: Disable NMI in Crash Kernel
- Fix potential dereferencing of null pointer in watchdog_core
- Several other small fixes and improvements
* tag 'linux-watchdog-5.11-rc1' of git://www.linux-watchdog.org/linux-watchdog: (23 commits)
watchdog: convert comma to semicolon
watchdog: iTCO_wdt: use dev_*() instead of pr_*() for logging
dt-binding: watchdog: add Rockchip compatibles to snps,dw-wdt.yaml
watchdog: coh901327: add COMMON_CLK dependency
dt-bindings: watchdog: sun4i: Add A100 compatible
watchdog: qcom: Avoid context switch in restart handler
watchdog: iTCO_wdt: use module_platform_device() macro
watchdog: Fix potential dereferencing of null pointer
watchdog: wdat_wdt: Fix missing kerneldoc reported by W=1
watchdog/hpwdt: Reflect changes
watchdog/hpwdt: Disable NMI in Crash Kernel
wdt: sp805: add watchdog_stop on reboot
watchdog: sbc_fitpc2_wdt: add __user annotations
watchdog: geodewdt: remove unneeded break
watchdog: rti-wdt: fix reference leak in rti_wdt_probe
watchdog: qcom_wdt: set WDOG_HW_RUNNING bit when appropriate
watchdog: remove pnx83xx driver
watchdog: stm32_iwdg: don't print an error on probe deferral
watchdog: sprd: change to use usleep_range() instead of busy loop
watchdog: sprd: check busy bit before new loading rather than after that
...
|
|
Commit f9c6cea0b385 ("ibmvnic: Skip fatal error reset after passive init")
says "If the passive
CRQ initialization occurs before the FATAL reset task is processed,
the FATAL error reset task would try to access a CRQ message queue
that was freed, causing an oops. The problem may be most likely to
occur during DLPAR add vNIC with a non-default MTU, because the DLPAR
process will automatically issue a change MTU request.
Fix this by not processing fatal error reset if CRQ is passively
initialized after client-driven CRQ initialization fails."
The original commit skips a specific reset condition, but that does
not fix the problem it claims to fix, and misses a reset condition.
The effective fix is commit 0e435befaea4 ("ibmvnic: fix NULL pointer
dereference in ibmvic_reset_crq") and commit a0faaa27c716 ("ibmvnic:
fix NULL pointer dereference in reset_sub_crq_queues"). With above
two fixes, there are no more crashes seen as described even without
the original commit, so I would like to revert the original commit.
Fixes: f9c6cea0b385 ("ibmvnic: Skip fatal error reset after passive init")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201223204904.12677-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When mdiobus_register() fails, priv->mdio allocated
by mdiobus_alloc() has not been freed, which leads
to memleak.
Fixes: e7f4dc3536a4 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201223110615.31389-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch implements the same basic fix for event rings as the
previous one does for channels.
The result of issuing an event ring control command should be that
the event ring changes state. If enabled, a completion interrupt
signals that the event ring state has changed. This interrupt is
enabled by gsi_evt_ring_command() and disabled again after the
command has completed (or we time out).
There is a window of time during which the command could complete
successfully without interrupting. This would cause the event ring
to transition to the desired new state.
So whether a event ring command ends via completion interrupt or
timeout, we can consider the command successful if the event ring
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The result of issuing a channel control command should be that the
channel changes state. If enabled, a completion interrupt signals
that the channel state has changed. This interrupt is enabled by
gsi_channel_command() and disabled again after the command has
completed (or we time out).
There is a window of time--after the completion interrupt is disabled
but before the channel state is read--during which the command could
complete successfully without interrupting. This would cause the
channel to transition to the desired new state.
So whether a channel command ends via completion interrupt or
timeout, we can consider the command successful if the channel
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: d6c9e3f506ae8 ("net: ipa: only enable generic command completion IRQ when needed");
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We enable the completion interrupt for channel or event ring
commands only when we issue them. The interrupt is disabled after
the interrupt has fired, or after we have timed out waiting for it.
If we time out, the command could complete after the interrupt has
been disabled, causing a state change in the channel or event ring.
The interrupt associated with that state change would be delivered
the next time the completion interrupt is enabled.
To avoid previous command completions interfering with new commands,
clear all pending completion interrupts before re-enabling them for
a new command.
Fixes: b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add TGL-H PCI info and PCI IDs for the new TSN Controller to the list
of supported devices.
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Link: https://lore.kernel.org/r/20201222160337.30870-1-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in memory leak.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This is not a scsi driver.
Reviewed-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes a crash in drm_object_property_set_value() because the property
is not set for internal DP ports that connect to a bridge chips
(e.g., DP to VGA or DP to LVDS).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210739
Fixes: 65bf2cf95d3ade ("drm/amdgpu: utilize subconnector property for DP through atombios")
Tested-By: Kris Karas <bugs-a17@moonlit-rail.com>
Cc: Oleg Vasilev <oleg.vasilev@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x
|
|
This can suppress the annoying but unharmful prompts.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- restore lvtma_pwrseq_delay2 from vbios integrated info table
- restore MVID/NVID after power up.
- Enable timer wake up mask when enable timer interrupt.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
new_crtc_state is already dereferenced earlier in the function
[How]
Remove the check
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Need driver to pass values of backlight ramp start and ramp reduction so
that intensity can be ramped down appropriately.
[How]
Using abm_parameters structure to get these values from driver.
Signed-off-by: Rizvi <syerizvi@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
The sink count change HPD_IRQ will be ignored if the branch device has only
DP DFP.
[how]
To remove the port type restriction.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Some MST display may not report the internal panel to DEVICE_COUNT,
that makes the check condition always failed.
[how]
To update this condition with the reported device count + 1
(because the immediate repeater's internal panel is possibly
not included in DEVICE_COUNT)
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
handler is supposedly passed in as a function pointer;
however, the entire struct amdgpu_dm_irq_handler_data
gets from the list is used to check match.
[how]
use the interrupt_handler within amdgpu_dm_irq_handler_data
for checking match.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
GUI_IDLE interrupts controlled by CP_INT_CNTL_RING0
are only applicable to me0 pipe0.
For ASICs that have gfx pipe removed, don't toggle
those bits.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The number of crtc should be 0 for ASICs that don't
have display engine. Remove the unnecessary asic type
check then.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Check number of gfx ring, rather than asic type,
before cp gfx engine initialization so driver just
need to make sure number of gfx ring is initialized
correctly in gfx early_init phase. No need to add
additional asic type check everywhere when there is
new asic with gfx pipe removed.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When the core clock rate and interconnect bandwidth specifications
were moved into configuration data, a copy/paste bug was introduced,
causing the memory interconnect bandwidth to be set three times
rather than enabling the three different interconnects.
Fix this bug.
Fixes: 91d02f9551501 ("net: ipa: use config data for clocking")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201222151613.5730-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
virtnet_set_channels can recursively call cpus_read_lock if CONFIG_XPS
and CONFIG_HOTPLUG are enabled.
The path is:
virtnet_set_channels - calls get_online_cpus(), which is a trivial
wrapper around cpus_read_lock()
netif_set_real_num_tx_queues
netif_reset_xps_queues_gt
netif_reset_xps_queues - calls cpus_read_lock()
This call chain and potential deadlock happens when the number of TX
queues is reduced.
This commit the removes netif_set_real_num_[tr]x_queues calls from
inside the get/put_online_cpus section, as they don't require that it
be held.
Fixes: 47be24796c13 ("virtio-net: fix the set affinity bug when CPU IDs are not consecutive")
Signed-off-by: Jeff Dike <jdike@akamai.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20201223025421.671-1-jdike@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Coly Li <colyli@sue.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There have no reassign the bdev after check It is IS_ERR.
the double check !IS_ERR(bdev) is superfluous.
After commit 4e7b5671c6a8 ("block: remove i_bdev"),
"Switch the block device lookup interfaces to directly work with a dev_t
so that struct block_device references are only acquired by the
blkdev_get variants (and the blk-cgroup special case). This means that
we now don't need an extra reference in the inode and can generally
simplify handling of struct block_device to keep the lookups contained
in the core block layer code."
so after lookup_bdev call, there no need to do bdput.
remove a superfluous check the bdev & don't call bdput after lookup_bdev.
Fixes: 4e7b5671c6a8("block: remove i_bdev")
Signed-off-by: Yi Li <yili@winhong.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch includes a missing dependency (CRYPTO_AES) which may
lead to an "undefined reference to `aes_expandkey'" linking error.
Fixes: 5106dfeaeabe ("crypto: qat - add AES-XTS support for QAT GEN4 devices")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add dependency for CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 on HAS_IOMEM to
prevent build failures.
Fixes: 88574332451380f4 ("crypto: keembay - Add support for Keem Bay OCS AES/SM4")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The Intel Keem Bay Offload and Crypto Subsystem (OCS) is only present on
Intel Keem Bay SoCs. Hence add a dependency on ARCH_KEEMBAY, to prevent
asking the user about this driver when configuring a kernel without
Intel Keem Bay platform support.
While at it, fix a misspelling of "cipher".
Fixes: 88574332451380f4 ("crypto: keembay - Add support for Keem Bay OCS AES/SM4")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
First set of fixes for v5.11, more fixes than usual this time. For
ath11k we have several fixes for QCA6390 PCI support and mt76 has
several. Also one build fix for mt76.
mt76
* fix two NULL pointer dereference
* fix build error when CONFIG_MAC80211_MESH is disabled
rtlwifi
* fix use-after-free in firmware handling code
ath11k
* error handling fixes
* fix crash found during connect and disconnect test
* handle HT disable better
* avoid printing qmi memory failure during firmware bootup
* disable ASPM during firmware bootup
* tag 'wireless-drivers-2020-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
MAINTAINERS: switch to different email address
mt76: mt7915: fix MESH ifdef block
mt76: mt76s: fix NULL pointer dereference in mt76s_process_tx_queue
mt76: sdio: remove wake logic in mt76s_process_tx_queue
mt76: usb: remove wake logic in mt76u_status_worker
ath11k: pci: disable ASPM L0sLs before downloading firmware
ath11k: qmi: try to allocate a big block of DMA memory first
rtlwifi: rise completion at the last step of firmware callback
mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker
ath11k: Fix ath11k_pci_fix_l1ss()
ath11k: Fix error code in ath11k_core_suspend()
ath11k: start vdev if a bss peer is already created
ath11k: fix crash caused by NULL rx_channel
ath11k: add missing null check on allocated skb
====================
Link: https://lore.kernel.org/r/20201222163727.D4336C433C6@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPIP tunnels packets are unknown to device,
hence these packets are incorrectly parsed and
caused the packet corruption, so disable offlods
for such packets at run time.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20201221145530.7771-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When mvneta_port_power_up() fails, we should execute
cleanup functions after label err_netdev to avoid memleak.
Fixes: 41c2b6b4f0f80 ("net: ethernet: mvneta: Add back interface mode validation")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20201220082930.21623-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 34f0f4e3f488 ("ibmvnic: Fix login buffer memory leaks") frees
login_rsp_buffer in release_resources() and send_login()
because handle_login_rsp() does not free it.
Commit f3ae59c0c015 ("ibmvnic: store RX and TX subCRQ handle array in
ibmvnic_adapter struct") frees login_rsp_buffer in handle_login_rsp().
It seems unnecessary to free it in release_resources() and send_login().
There are chances that handle_login_rsp returns earlier without freeing
buffers. Double-checking the buffer is harmless since
release_login_buffer and release_login_rsp_buffer will
do nothing if buffer is already freed.
Fixes: f3ae59c0c015 ("ibmvnic: store RX and TX subCRQ handle array in ibmvnic_adapter struct")
Fixes: 34f0f4e3f488 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201219213919.21045-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dwmac glue registers on Amlogic Meson8b and newer SoCs has two clock
inputs:
- Meson8b and Meson8m2: MPLL2 and MPLL2 (the same parent is wired to
both inputs)
- GXBB, GXL, GXM, AXG, G12A, G12B, SM1: FCLK_DIV2 and MPLL2
All known vendor kernels and u-boots are using the first input only. We
let the common clock framework automatically choose the "right" parent.
For some boards this causes a problem though, specificially with G12A and
newer SoCs. The clock input is used for generating the 125MHz RGMII TX
clock. For the two input clocks this means on G12A:
- FCLK_DIV2: 999999985Hz / 8 = 124999998.125Hz
- MPLL2: 499999993Hz / 4 = 124999998.25Hz
In theory MPLL2 is the "better" clock input because it's gets us 0.125Hz
closer to the requested frequency than FCLK_DIV2. In reality however
there is a resource conflict because MPLL2 is needed to generate some of
the audio clocks. dwmac-meson8b probes first and sets up the clock tree
with MPLL2. This works fine until the audio driver comes and "steals"
the MPLL2 clocks and configures it with it's own rate (294909637Hz). The
common clock framework happily changes the MPLL2 rate but does not
reconfigure our RGMII TX clock tree, which then ends up at 73727409Hz,
which is more than 40% off the requested 125MHz.
Don't use the second clock input for now to force the common clock
framework to always select the first parent. This mimics the behavior
from the vendor driver and fixes the clock resource conflict with the
audio driver on G12A boards. Once the common clock framework can handle
this situation this change can be reverted again.
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20201219135036.3216017-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These make the ACPI enumeration of devices take _DEP information into
account more aggressively, fix device IDs matching in the ACPI part of
the PNP devices framework and update the ACPI code related to
suspend-to-idle to take systems based on AMD hardware into account
properly.
Specifics:
- Modify the ACPI device enumeration code to defer the enumeration of
devices with an _HID whose lists of operation region dependencies
returned by _DEP are not empty after eliminating the entries
representing known-benign dependencies from them (Rafael Wysocki,
Hans de Goede).
- Make the ACPI PNP code mathing device IDs also take the length of
the given ID string into account (Hui Wang).
- Add AMD systems support to the ACPI code handling suspend-to-idle
via the PNP0D80 (System Power Management Controller) device _DSM
interface (Shyam Sundar).
- Move the suspend-to-idle handling code related to the PNP0D80
device _DSM interface, which is x86-specific, to a separate file in
the x86/ subdirectory (Rafael Wysocki)"
* tag 'acpi-5.11-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Move x86-specific code to the x86 directory
ACPI: scan: Add Intel Baytrail Mailbox Device to acpi_ignore_dep_ids
ACPI: scan: Avoid unnecessary second pass in acpi_bus_scan()
ACPI: scan: Defer enumeration of devices with _DEP lists
ACPI: scan: Evaluate _DEP before adding the device
ACPI: PM: s2idle: Add AMD support to handle _DSM
ACPI: PNP: compare the string length in the matching_id()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These update the CPPC cpufreq driver and intel_pstate (which involves
updating the cpufreq core and the schedutil governor) and make
janitorial changes in the ACPI code handling processor objects.
Specifics:
- Rework the passive-mode "fast switch" path in the intel_pstate
driver to allow it receive the minimum (required) and target
(desired) performance information from the schedutil governor so as
to avoid running some workloads too fast (Rafael Wysocki).
- Make the intel_pstate driver allow the policy max limit to be
increased after the guaranteed performance value for the given CPU
has increased (Rafael Wysocki).
- Clean up the handling of CPU coordination types in the CPPC cpufreq
driver and make it export frequency domains information to user
space via sysfs (Ionela Voinescu).
- Fix the ACPI code handling processor objects to use a correct
coordination type when it fails to map frequency domains and drop a
redundant CPU map initialization from it (Ionela Voinescu, Punit
Agrawal)"
* tag 'pm-5.11-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Use most recent guaranteed performance values
cpufreq: intel_pstate: Implement the ->adjust_perf() callback
cpufreq: Add special-purpose fast-switching callback for drivers
cpufreq: schedutil: Add util to struct sg_cpu
cppc_cpufreq: replace per-cpu data array with a list
cppc_cpufreq: expose information on frequency domains
cppc_cpufreq: clarify support for coordination types
cppc_cpufreq: use policy->cpu as driver of frequency setting
ACPI: processor: fix NONE coordination for domain mapping failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Add DM verity support for signature verification with 2nd keyring
- Fix DM verity to skip verity work if IO completes with error while
system is shutting down
- Add new DM multipath "IO affinity" path selector that maps IO
destined to a given path to a specific CPU based on user provided
mapping
- Rename DM multipath path selector source files to have "dm-ps" prefix
- Add REQ_NOWAIT support to some other simple DM targets that don't
block in more elaborate ways waiting for IO
- Export DM crypt's kcryptd workqueue via sysfs (WQ_SYSFS)
- Fix error return code in DM's target_message() if empty message is
received
- A handful of other small cleanups
* tag 'for-5.11/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: simplify the return expression of load_mapping()
dm ebs: avoid double unlikely() notation when using IS_ERR()
dm verity: skip verity work if I/O error when system is shutting down
dm crypt: export sysfs of kcryptd workqueue
dm ioctl: fix error return code in target_message
dm crypt: Constify static crypt_iv_operations
dm: add support for REQ_NOWAIT to various targets
dm: rename multipath path selector source files to have "dm-ps" prefix
dm mpath: add IO affinity path selector
dm verity: Add support for signature verification with 2nd keyring
dm: remove unnecessary current->bio_list check when submitting split bio
|
|
* pm-cpufreq:
cpufreq: intel_pstate: Use most recent guaranteed performance values
cpufreq: intel_pstate: Implement the ->adjust_perf() callback
cpufreq: Add special-purpose fast-switching callback for drivers
cpufreq: schedutil: Add util to struct sg_cpu
cppc_cpufreq: replace per-cpu data array with a list
cppc_cpufreq: expose information on frequency domains
cppc_cpufreq: clarify support for coordination types
cppc_cpufreq: use policy->cpu as driver of frequency setting
ACPI: processor: fix NONE coordination for domain mapping failure
ACPI: processor: Drop duplicate setting of shared_cpu_map
|
|
Voltages and current are reported by Zen CPUs. However, the means
to do so is undocumented, changes from CPU to CPU, and the raw data
is not calibrated. Calibration information is available, but again
not documented. This results in less than perfect user experience,
up to concerns that loading the driver might possibly damage
the hardware (by reporting out-of range voltages). Effectively
support for reporting voltages and current is not maintainable.
Drop it.
Cc: Artem S. Tashkinov <aros@gmx.com>
Cc: Wei Huang <wei.huang2@amd.com>
Tested-by: Wei Huang <wei.huang2@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|