| Age | Commit message (Collapse) | Author |
|---|
|
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit a144ea4b7a13087081ab5402fa9ad0bcfd249e67 [IPV4]: annotate struct in_ifaddr
Missed this extra byteswap as the isdn inlines hide the htonl inside
put_u32 which causes an extra byteswap on little-endian arches.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2
http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).
Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed debug print statements and improved conditionals around informational statements.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Joey Zhuo <joeyzhuo@via.com.tw>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the change the driver reported the same pause parameters
for all the ports, even only one of them was modified.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
Commit 46abc02175b3c246dd5141d878f565a8725060c9 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Of the various WOL options provided in include/linux/ethtool.h, the
L1 NIC supports only magic packet. Remove all options except magic
packet from the atl1 driver.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Inverting the crc after calling ether_crc_le() is unnecessary and breaks
multicast. Remove it.
Tested-by: David Madore <david.madore@ens.fr>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
We weren't unmapping DMA memory, which will break when gianfar gets used
on systems with more than 32-bits of memory. Also, it's just plain wrong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
p_{tx,rx}_fw_statistics_pram are special: they're available only when
a device is open. If the device is closed, we should just fill the data
with zeroes.
Fixes the following oops:
root@b1:~# ifconfig eth1 down
root@b1:~# ethtool -S eth1
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01e1dcc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01e1dcc] uec_get_ethtool_stats+0x98/0x124
LR [c0287cc8] ethtool_get_stats+0xfc/0x23c
Call Trace:
[cfaadde0] [c0287ca8] ethtool_get_stats+0xdc/0x23c (unreliable)
[cfaade20] [c0288340] dev_ethtool+0x2fc/0x588
[cfaade50] [c0285648] dev_ioctl+0x290/0x33c
[cfaadea0] [c0272238] sock_ioctl+0x80/0x2ec
[cfaadec0] [c00b5ae4] vfs_ioctl+0x40/0xc0
[cfaadee0] [c00b5fa8] do_vfs_ioctl+0x78/0x20c
[cfaadf10] [c00b617c] sys_ioctl+0x40/0x74
[cfaadf40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
---[ end trace b941007b2dfb9759 ]---
Segmentation fault
p.s. While at it, also remove u64 casts, they aren't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This driver is pretty mature, and the worst of the known
problems has been fixed (the 32-bit failures due to readq
implementation).
So let's finally give it a version of 1.0
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the Sun CP3260 ATCA blade which is
a N2 based ATCA blade with 2 NIU ports. The NIU ports do not
have on-board PHY.
Signed-off-by: Santwona Behera <santwona.behera@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix bnx2 so that netpoll works properly. Specifically:
1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device
2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (35 commits)
V4L/DVB (9516): cx18: Move DVB buffer transfer handling from irq handler to work_queue
V4L/DVB (9557): gspca: Small changes for the sensor HV7131B in zc3xx.
V4L/DVB (9556): gspca: Bad init sequence for sensor HV7131B in zc3xx.
V4L/DVB (9549): gspca: Fix a typo in one of gspca chips name.
V4L/DVB (9515): cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup
V4L/DVB (9493): kconfig patch
V4L/DVB (9527): af9015: fix compile warnings
V4L/DVB (9524): af9013: fix bug in status reading
V4L/DVB (9511): cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call
V4L/DVB (9510): cx18: Fix write retries for registers that always change - part 2.
V4L/DVB (9506): ivtv/cx18: fix test whether modules should be loaded or not.
V4L/DVB (9499): cx88-mpeg: final fix for analogue only compilation + de-alloc fix
V4L/DVB (9496): cx88-blackbird: bugfix: cx88-blackbird-mpeg-users
V4L/DVB (9495): cx88-blackbird: bugfix: cx88-blackbird-poll-fix
V4L/DVB (9494): anysee: initialize anysee_usb_mutex statically
V4L/DVB (9492): unplug oops from dvb_frontend_init...
V4L/DVB (9486): ivtv/ivtvfb: no longer experimental
V4L/DVB (9485): ivtv: remove incorrect V4L1 & tvaudio dependency
V4L/DVB (9482): Documentation, especially regarding audio and informational links
V4L/DVB (9475): cx18: Disable write retries for registers that always change - part 1.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Update desktop/server defconfigs
powerpc: Fix msr check in compat_sys_swapcontext
powerpc: Repair device bindings documentation
powerpc: Updated Freescale PPC related defconfigs
powerpc: Update QE/CPM2 usb_ctlr structures for USB support
powerpc/86xx: Correct SOC bus-frequency in GE Fanuc SBC610 DTS
powerpc: Fix Book-E watchdog timer interval setting
powerpc/fsl-booke: Fix synchronization bug w/local tlb invalidates
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Move legacy breadcrumb out of the reserved status page area
drm/i915: Filter pci devices based on PCI_CLASS_DISPLAY_VGA
drm/radeon: map registers at load time
drm: Remove infrastructure for supporting i915's vblank swapping.
i915: Remove racy delayed vblank swap ioctl.
i915: Don't whine when pci_enable_msi() fails.
i915: Don't attempt to short-circuit object_wait_rendering by checking domains.
i915: Clean up sarea pointers on leavevt
i915: Save/restore MCHBAR_RENDER_STANDBY on GM965/GM45
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: fix last_reset timestamp handling
libata: Avoid overflow in ata_tf_read_block() when tf->hba_lbal > 127
[libata] pata_pcmcia: another memory card support
[libata] pata_sch: notice attached slave devices
[libata] pata_cs553*.c: cleanup kernel-doc
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
dsa: fix master interface allmulti/promisc handling
dsa: fix skb->pkt_type when mac address of slave interface differs
net: fix setting of skb->tail in skb_recycle_check()
net: fix /proc/net/snmp as memory corruptor
mac80211: fix a buffer overrun in station debug code
netfilter: payload_len is be16, add size of struct rather than size of pointer
ipv6: fix ip6_mr_init error path
[4/4] dca: fixup initialization dependency
[3/4] I/OAT: fix async_tx.callback checking
[2/4] I/OAT: fix dma_pin_iovec_pages() error handling
[1/4] I/OAT: fix channel resources free for not allocated channels
ssb: Fix DMA-API compilation for non-PCI systems
SSB: hide empty sub menu
vlan: Fix typos in proc output string
[netdrvr] usb/hso: Cleanup rfkill error handling
sfc: Correct address of gPXE boot configuration in EEPROM
el3_common_init() should be __devinit, not __init
hso: rfkill type should be WWAN
mlx4_en: Start port error flow bug fix
af_key: mark policy as dead before destroying
|
|
work_queue
cx18: Move DVB buffer transfer handling from irq handler to work_queue thread.
In order to properly lock the epu2cpu mailbox for driver to CX23418 commands,
the DVB/TS buffer handling needs to be moved from the IRQ handler and IRQ
context to a work queue. This work_queue implmentation is strikingly similar
to the ivtv implementation - for better or worse.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- touch only one register for brightness change
- no quality control
- don't probe again at streamon time.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes the H flip and the R & B color inversion of mode 320x240.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
handling cleanup
cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup.
The SCB field definitions for Ack IRQ's for mailboxes were inconsistent with
the bitmasks being loaded into those SCB fields and the SW2 Ack IRQ handling
logic. Renamed fields in SCB to make things consistent and did misc IRQ
handling cleanups: removing legacy ivtv dma_reg_lock, HPU IRQ flags, etc.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Ok I made a patch that converts gspca kconfig file to a more standard=
one, with tabs + 2 white spaces, so that if a warning is added it still
compiles
please find it attached
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- use static to avoid compile warnings
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- ! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call.
Give the encoder time to complete the MDL release before destroying the
encoder internal task. This avoids an encoder lockup on the next digital
capture and error messages about buffers being returned for an inactive
encoder task handle.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
part 2.
cx18: Fix write retries for registers that always change - part 2.
Some registers, especially interrupt related ones, will never read
back the value just written. Modified interrupt register readback
checks to make sure the intended effect was achieved.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
de-alloc fix
Final fix for when analogue only is selected
for compilation (ie, !CX88_DVB)
This tidies up previous fix and adds missing
de-alloc memory leak on fault (eg, if fe1 fails to alloc
where fe0 was allocated).
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Allows multiple access to the mpeg device
Signed-off-by: Frederic CAND <frederic.cand@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
