Age | Commit message (Collapse) | Author |
|
Extended Address Space Descriptors are new in ACPI 3.0 and allow the
BIOS to communicate device resource cacheability attributes (write-back,
write-through, uncacheable, etc) to the OS.
Previously, PNPACPI ignored these descriptors, so if a BIOS used them,
a device could be responding at addresses the OS doesn't know about.
This patch adds support for these descriptors in _CRS and _PRS. We
don't attempt to encode them for _SRS (just like we don't attempt to
encode the existing 16-, 32-, and 64-bit Address Space Descriptors).
Unfortunately, I don't have a way to test this.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add support for VGA load detection (pre-945).
drm/i915: Use an I2C algo to do the flip to SDVO DDC bus.
drm/i915: Determine type before initialising connector
drm/i915: Return SDVO LVDS VBT mode if no EDID modes are detected.
drm/i915: Fetch SDVO LVDS mode lines from VBT, then reserve them
i915: support 8xx desktop cursors
drm/i915: allocate large pointer arrays with vmalloc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: fix cpu buffer size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: determine exact CPU frequency for HW Pstates
[CPUFREQ] powernow-k8 cleanup msg if BIOS does not export ACPI _PSS cpufreq data
[CPUFREQ] fix timer teardown in ondemand governor
[CPUFREQ] fix timer teardown in conservative governor
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call
[CPUFREQ] powernow-k7 build fix when ACPI=n
[CPUFREQ] add atom family to p4-clockmod
|
|
When KVM is loaded, and hence VT set up, the vmcall instruction in an
lguest guest causes a #GP, not #UD.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
r8169: avoid losing MSI interrupts
tcp: tcp_vegas ssthresh bugfix
mac8390: fix regression caused during net_device_ops conversion
gianfar: fix BUG under load after introduction of skb recycling
wimax/i2400m: usb: fix device reset on autosuspend while not yet idle
RxRPC: Error handling for rxrpc_alloc_connection()
ipv4: Fix oops with FIB_TRIE
pktgen: do not access flows[] beyond its length
gigaset: beyond ARRAY_SIZE of iwb->data
IPv6: set RTPROT_KERNEL to initial route
net: fix rtable leak in net/ipv4/route.c
net: fix length computation in rt_check_expire()
wireless: beyond ARRAY_SIZE of intf->crypto_stats
iwlwifi: update 5000 ucode support to version 2 of API
cfg80211: fix race between core hint and driver's custom apply
airo: fix airo_get_encode{,ext} buffer overflow like I mean it...
ath5k: fix interpolation with equal power levels
iwlwifi: do not cancel delayed work inside spin_lock_irqsave
ath5k: fix exp off-by-one when computing OFDM delta slope
wext: verify buffer size for SIOCSIWENCODEEXT
...
|
|
* 'for-linus' of git://neil.brown.name/md:
md: don't use locked_ioctl.
md: don't update curr_resync_completed without also updating reshape_position.
md: raid5: avoid sector values going negative when testing reshape progress.
md: export 'frozen' resync state through sysfs
md: bitmap: improve bitmap maintenance code.
md: improve errno return when setting array_size
md: always update level / chunk_size / layout when writing v1.x metadata.
|
|
Two approaches for VGA detections: hot plug detection for 945G onwards
and load pipe detection for Pre-945G. Load pipe detection will get one free
pipe, set border color as red and blue, then check CRT status by
swf register. This is a sync-up with the 2D driver.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
>
(updated changelog)
cpufreq fix timer teardown in ondemand governor
The problem is that dbs_timer_exit() uses cancel_delayed_work() when it should
use cancel_delayed_work_sync(). cancel_delayed_work() does not wait for the
workqueue handler to exit.
The ondemand governor does not seem to be affected because the
"if (!dbs_info->enable)" check at the beginning of the workqueue handler returns
immediately without rescheduling the work. The conservative governor in
2.6.30-rc has the same check as the ondemand governor, which makes things
usually run smoothly. However, if the governor is quickly stopped and then
started, this could lead to the following race :
dbs_enable could be reenabled and multiple do_dbs_timer handlers would run.
This is why a synchronized teardown is required.
The following patch applies to, at least, 2.6.28.x, 2.6.29.1, 2.6.30-rc2.
Depends on patch
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: gregkh@suse.de
CC: stable@kernel.org
CC: cpufreq@vger.kernel.org
CC: Ingo Molnar <mingo@elte.hu>
CC: rjw@sisk.pl
CC: Ben Slusky <sluskyb@paranoiacs.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
>
(re-send with updated changelog)
cpufreq fix timer teardown in conservative governor
The problem is that dbs_timer_exit() uses cancel_delayed_work() when it should
use cancel_delayed_work_sync(). cancel_delayed_work() does not wait for the
workqueue handler to exit.
The ondemand governor does not seem to be affected because the
"if (!dbs_info->enable)" check at the beginning of the workqueue handler returns
immediately without rescheduling the work. The conservative governor in
2.6.30-rc has the same check as the ondemand governor, which makes things
usually run smoothly. However, if the governor is quickly stopped and then
started, this could lead to the following race :
dbs_enable could be reenabled and multiple do_dbs_timer handlers would run.
This is why a synchronized teardown is required.
Depends on patch
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
The following patch applies to 2.6.30-rc2. Stable kernels have a similar
issue which should also be fixed, but the code changed between 2.6.29
and 2.6.30, so this patch only applies to 2.6.30-rc.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: gregkh@suse.de
CC: stable@kernel.org
CC: cpufreq@vger.kernel.org
CC: Ingo Molnar <mingo@elte.hu>
CC: rjw@sisk.pl
CC: Ben Slusky <sluskyb@paranoiacs.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
The patches linked above depend on the following patch to remove
circular locking dependency :
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
(the following issue was faced when using cancel_delayed_work_sync() in the
timer teardown (which fixes a race).
* KOSAKI Motohiro (kosaki.motohiro@jp.fujitsu.com) wrote:
> Hi
>
> my box output following warnings.
> it seems regression by commit 7ccc7608b836e58fbacf65ee4f8eefa288e86fac.
>
> A: work -> do_dbs_timer() -> cpu_policy_rwsem
> B: store() -> cpu_policy_rwsem -> cpufreq_governor_dbs() -> work
>
>
Hrm, I think it must be due to my attempt to fix the timer teardown race
in ondemand governor mixed with new locking behavior in 2.6.30-rc.
The rwlock seems to be taken around the whole call to
cpufreq_governor_dbs(), when it should be only taken around accesses to
the locked data, and especially *not* around the call to
dbs_timer_exit().
Reverting my fix attempt would put the teardown race back in place
(replacing the cancel_delayed_work_sync by cancel_delayed_work).
Instead, a proper fix would imply modifying this critical section :
cpufreq.c: __cpufreq_remove_dev()
...
if (cpufreq_driver->target)
__cpufreq_governor(data, CPUFREQ_GOV_STOP);
unlock_policy_rwsem_write(cpu);
To make sure the __cpufreq_governor() callback is not called with rwsem
held. This would allow execution of cancel_delayed_work_sync() without
being nested within the rwsem.
Applies on top of the 2.6.30-rc5 tree.
Required to remove circular dep in teardown of both conservative and
ondemande governors so they can use cancel_delayed_work_sync().
CPUFREQ_GOV_STOP does not modify the policy, therefore this locking seemed
unneeded.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Greg KH <greg@kroah.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: "Rafael J. Wysocki" <rjw@sisk.pl>
CC: Ben Slusky <sluskyb@paranoiacs.org>
CC: Chris Wright <chrisw@sous-sol.org>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/inaky/wimax
|
|
The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.
The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: David Dillow <dave@thedillows.org>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changeset ca17584bf2ad1b1e37a5c0e4386728cc5fc9dabc ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.
Tested with a Kinetics EtherPort card.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
md has no need for the BKL - it does its own locking.
So md_ioctl doesn't need to be a locked_ioctl.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
In order for the metadata to always be consistent, we mustn't updated
curr_resync_completed without also updating reshape_position.
The reshape code updates both at the same time. However since
commit 97e4f42d62badb0f9fbc27c013e89bc1336a03bc
the common md_do_sync will sometimes update curr_resync_completed
but is not in a position to update reshape_position.
So if MD_RECOVERY_RESHAPE is set (indicating that a reshape is
happening, so reshape_position might change), don't update
curr_resync_completed in md_do_sync, leave it to the per-personality
reshape code.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
As sector_t in unsigned, we cannot afford to let 'safepos' etc go
negative.
So replace
a -= b;
by
a -= min(b,a);
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The md resync engine has a 'frozen' state which ensures that
no resync/recovery. This is used to avoid races.
Export this state through the 'sync_action' sysfs attribute
so that user-space can benefit and also avoid some races.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The code for checking which bits in the bitmap can be cleared
has 2 problems:
1/ it repeatedly takes and drops a spinlock, where it would make
more sense to just hold on to it most of the time.
2/ it doesn't make use of some opportunities to skip large sections
of the bitmap
This patch fixes those. It will only affect CPU consumption, not
correctness.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Instead of always returns EINVAL if anything goes wrong
when setting the array size, add the option of
E2BIG
if the size requested is too large. This makes it easier
for user-space to be sure what went wrong.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
We previously didn't update these fields when writing the metadata
because they could never change. They can now, so we better write
them.
v0.90 metadata always updated these fields.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Since commit 0fd56bb5be6455d0d42241e65aed057244665e5e ("gianfar:
Add support for skb recycling"), gianfar puts skbuffs that are in
the rx ring back onto the recycle list as-is in case there was a
receive error, but this breaks the following invariant: that all
skbuffs on the recycle list have skb->data = skb->head + NET_SKB_PAD.
The RXBUF_ALIGNMENT realignment done in gfar_new_skb() will be done
twice on skbuffs recycled in this way, causing there not to be enough
room in the skb anymore to receive a full packet, eventually leading
to an skb_over_panic from gfar_clean_rx_ring() -> skb_put().
Resetting the skb->data pointer to skb->head + NET_SKB_PAD before
putting the skb back onto the recycle list restores the mentioned
invariant, and should fix this issue.
Reported-by: Michael Guntsche <mike@it-loops.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We shouldn't hold dpm_list_mtx while executing
[disable|enable]_nonboot_cpus(), because theoretically this may lead
to a deadlock as shown by the following example (provided by Johannes
Berg):
CPU 3 CPU 2 CPU 1
suspend/hibernate
something:
rtnl_lock() device_pm_lock()
-> mutex_lock(&dpm_list_mtx)
mutex_lock(&dpm_list_mtx)
linkwatch_work
-> rtnl_lock()
disable_nonboot_cpus()
-> flush CPU 3 workqueue
Fortunately, device drivers are supposed to stop any activities that
might lead to the registration of new device objects way before
disable_nonboot_cpus() is called, so it shouldn't be necessary to
hold dpm_list_mtx over the entire late part of device suspend and
early part of device resume.
Thus, during the late suspend and the early resume of devices acquire
dpm_list_mtx only when dpm_list is going to be traversed and release
it right after that.
This patch is reported to fix the regressions tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=13245.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt2sas: fix driver version inconsistency
[SCSI] 3w-xxxx: scsi_dma_unmap fix
[SCSI] 3w-9xxx: scsi_dma_unmap fix
[SCSI] ses: fix problems caused by empty SES provided name
[SCSI] fc-transport: Close state transition-window during rport deletion.
[SCSI] initialize max_target_blocked in scsi_alloc_target
[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA
|
|
Actually the icom driver is crashing when is being removed because
the driver is kfreeing the adapter structure before calling
pci_release_regions(), which result in the following error:
Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6d33
Faulting instruction address: 0xc000000000246b80
Oops: Kernel access of bad area, sig: 11 [#1]
....
[c000000012d436a0] [c0000000001002d0] .kfree+0x120/0x34c (unreliable)
[c000000012d43730] [c000000000246d60] .pci_release_selected_regions+0x3c/0x68
[c000000012d437c0] [d000000002d54700] .icom_kref_release+0xf4/0x118 [icom]
[c000000012d43850] [c000000000232e50] .kref_put+0x74/0x94
[c000000012d438d0] [d000000002d56c58] .icom_remove+0x40/0xa4 [icom]
[c000000012d43960] [c000000000249e48] .pci_device_remove+0x50/0x90
[c000000012d439e0] [c0000000002d68d8] .__device_release_driver+0x94/0xd4
[c000000012d43a70] [c0000000002d7104] .driver_detach+0xf8/0x12c
[c000000012d43b00] [c0000000002d549c] .bus_remove_driver+0xbc/0x11c
[c000000012d43b90] [c0000000002d71dc] .driver_unregister+0x60/0x80
[c000000012d43c20] [c00000000024a07c] .pci_unregister_driver+0x44/0xe8
[c000000012d43cb0] [d000000002d56bf4] .icom_exit+0x1c/0x40 [icom]
[c000000012d43d30] [c000000000095fa8] .SyS_delete_module+0x214/0x2a8
[c000000012d43e30] [c00000000000852c] syscall_exit+0x0/0x40
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: stable@kernel.org
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Previously, we would set the control bus switch before calls were made
to request EDID information over DDC. But recently the DDC code started
doing multiple I2C transfers to get the EDID extensions as well. This
tripped up SDVO, because the control bus switch is only in effect until
the next STOP after a START. By doing our own algo, we can wrap each i2c
transaction on the DDC I2C bus with the control bus switch it requires.
freedesktop.org bug #21042
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Hand application for conflict, fixed error path]
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
drm_connector_init sets both the connector type and the connector type_id
on the newly initialised connector. As the connector type_id is coupled to
the connector type, the connector type cannot simply be modified on an
initialised connector.
This patch changes the order of operations on intel_sdvo_init so that the
type is determined before the connector is intialised.
This fixes a bug whereby the name card0-VGA-1 would be allocted to both a
CRT and an SDVO connector since the SDVO connector would be initialised
with type 'unknown' and hence have its type_id assigned from the wrong pool.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Some new SDVO LVDS hardware doesn't have DDC available, and this should
fix the display on it.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
For some reason we never added 8xx desktop cursor support to the
kernel. This patch fixes that.
[krh: Also set the size on pre-i915 hw.]
Tested-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
via82cxxx: Add VIA VX855 PCI Device ID
ide: report timeouts in ide_busy_sleep()
ide: improve failed opcode reporting
ide: fix printk() levels in ide_dump_ata[pi]_error()
ide: fix OOPS during ide-cd error recovery
ide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
video: stop sh_mobile_lcdcfb only if started
sh: ap325 camera without i2c driver fix
|
|
Instead of queuing IPMB messages before channel initialization, just
throw them away. Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.
Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Cc: Dan Frazier <dannf@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* change 'hwif' argument to 'drive'
* report an error on timeout
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fixes "<3>" in error messages like this one:
hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit 8588a2b732928b343233af9b1855705b8286bed4
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit e97564f362a93f8c248246c19828895950341252
("ide: More TSST drives with broken cable detection")
and in:
commit 3ced5c49bd2d1f2c7f769e3a54385883de63a652
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.
If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.
To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is rejected (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
|
This patch fixes the LCDC driver to avoid calling the
function sh_mobile_lcdc_start_stop(priv, 0) unless the
same function has been called before to start the LCDC
hardware.
Triggered when sh_mobile_lcdcfb.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI PM: Fix initialization and kexec breakage for some devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6:
drm: Copy back ioctl data to userspace regardless of return code.
drm: Round size of SHM maps to PAGE_SIZE
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
[ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *
[ARM] 5517/1: integrator: don't put clock lookups in __initdata
[ARM] 5518/1: versatile: don't put clock lookups in __initdata
[ARM] mach-l7200: fix spelling of SYS_CLOCK_OFF
[ARM] Double check memmap is actually valid with a memmap has unexpected holes V2
[ARM] realview: fix broadcast tick support
[ARM] realview: remove useless smp_cross_call_done()
[ARM] smp: fix cpumask usage in ARM SMP code
[ARM] 5513/1: Eurotech VIPER SBC: fix compilation error
[ARM] 5509/1: ep93xx: clkdev enable UARTS
ARM: OMAP2/3: Change omapfb to use clkdev for dispc and rfbi, v2
ARM: OMAP3: Fix HW SAVEANDRESTORE shift define
ARM: OMAP3: Fix number of GPIO lines for 34xx
[ARM] S3C: Do not set clk->owner field if unset
[ARM] S3C2410: mach-bast.c registering i2c data too early
[ARM] S3C24XX: Fix unused code warning in arch/arm/plat-s3c24xx/dma.c
[ARM] S3C64XX: fix GPIO debug
[ARM] S3C64XX: GPIO include cleanup
[ARM] nwfpe: fix 'floatx80_is_nan' sparse warning
[ARM] nwfpe: Add decleration for ExtendedCPDO
...
|
|
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fixes a regression from commit 9d5b3ffc42f7820e8ee07705496955e4c2c38dd9
('drm: fixup some of the ioctl function exit paths'): The vblank ioctl
needs to update the userspace parameters when interrupted by a signal,
which was prevented by the return code check. This could cause the X
server to hang in drmWaitVBlank().
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Do not go beyond ARRAY_SIZE of intf->crypto_stats
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"airo: airo_get_encode{,ext} potential buffer overflow" was actually a
no-op, due to an unrecognized type overflow in an assignment. Oddly,
gcc only seems to tell me about it when using -Wextra...grrr...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|