Age | Commit message (Collapse) | Author |
|
Pull pwm changes from Thierry Reding:
"A new driver has been added for the SPEAr platform and the
TWL4030/6030 driver has been replaced by two drivers that control the
regular PWMs and the PWM driven LEDs provided by the chips.
The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have
all been improved and the device tree bindings now support the PWM
signal polarity."
Fix up trivial conflicts due to __devinit/exit removal.
* tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (21 commits)
pwm: samsung: add missing s3c->pwm_id assignment
pwm: lpc32xx: Set the chip base for dynamic allocation
pwm: lpc32xx: Properly disable the clock on device removal
pwm: lpc32xx: Fix the PWM polarity
pwm: i.MX: eliminate build warning
pwm: Export of_pwm_xlate_with_flags()
pwm: Remove pwm-twl6030 driver
pwm: New driver to support PWM driven LEDs on TWL4030/6030 series of PMICs
pwm: New driver to support PWMs on TWL4030/6030 series of PMICs
pwm: pwm-tiehrpwm: pinctrl support
pwm: tiehrpwm: Add device-tree binding
pwm: pwm-tiehrpwm: Adding TBCLK gating support.
pwm: pwm-tiecap: pinctrl support
pwm: tiecap: Add device-tree binding
pwm: Add TI PWM subsystem driver
pwm: Device tree support for PWM polarity
pwm: vt8500: Ensure PWM clock is enabled during pwm_config
pwm: vt8500: Fix build error
pwm: spear: Staticize spear_pwm_config()
pwm: Add SPEAr PWM chip driver support
...
|
|
Pull battery update, part 2, from Anton Vorontsov:
"These are left overs that I didn't have time to review/apply before
the merge window opened. I didn't want to "spoil" the first pull
request with these late patches, so they were not included:
- A small patch for the RX51 OMAP board (Nokia N900 phone), the patch
creates a battery monitor device instance, so that it can be
probed. It was acked by the OMAP maintainer;
- A couple of late bug fixes for the charger-manager: corrects corner
cases for the battery full handling."
* tag 'for-v3.8-part2' of git://git.infradead.org/battery-2.6:
charger-manager: Fix bug when check dropped voltage after fullbatt event
charger-manager: Fix bug related to checking fully charged state of battery
ARM: OMAP: rx51: Register platform device for rx51_battery
|
|
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
|
|
Merge patches from Andrew Morton:
"Most of the rest of MM, plus a few dribs and drabs.
I still have quite a few irritating patches left around: ones with
dubious testing results, lack of review, ones which should have gone
via maintainer trees but the maintainers are slack, etc.
I need to be more activist in getting these things wrapped up outside
the merge window, but they're such a PITA."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (48 commits)
mm/vmscan.c: avoid possible deadlock caused by too_many_isolated()
vmscan: comment too_many_isolated()
mm/kmemleak.c: remove obsolete simple_strtoul
mm/memory_hotplug.c: improve comments
mm/hugetlb: create hugetlb cgroup file in hugetlb_init
mm/mprotect.c: coding-style cleanups
Documentation: ABI: /sys/devices/system/node/
slub: drop mutex before deleting sysfs entry
memcg: add comments clarifying aspects of cache attribute propagation
kmem: add slab-specific documentation about the kmem controller
slub: slub-specific propagation changes
slab: propagate tunable values
memcg: aggregate memcg cache values in slabinfo
memcg/sl[au]b: shrink dead caches
memcg/sl[au]b: track all the memcg children of a kmem_cache
memcg: destroy memcg caches
sl[au]b: allocate objects from memcg cache
sl[au]b: always get the cache from its page in kmem_cache_free()
memcg: skip memcg kmem allocations in specified code regions
memcg: infrastructure to match an allocation to the right cache
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixlet from Guenter Roeck:
"Fix fallout from __devexit removal"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (twl4030-madc-hwmon) Fix warning message caused by removal of __devexit
|
|
This happens to do the right thing in all cases on fibre channel but not on
other media types
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes the checkpatch error and warning as below:
WARNING: space prohibited between function name and open parenthesis '('
ERROR: trailing statements should be on next line
Also, long comments are fixed for the preferred style and unnecessary
lines are removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"As usual, there are a couple of new drivers, input core now supports
managed input devices (devres), a slew of drivers now have device tree
support and a bunch of fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: walkera0701 - fix crash on startup
Input: matrix-keymap - provide a proper module license
Input: gpio_keys_polled - switch to using gpio_request_one()
Input: gpio_keys - switch to using gpio_request_one()
Input: wacom - fix touch support for Bamboo Fun CTH-461
Input: xpad - add a few new VID/PID combinations
Input: xpad - minor formatting fixes
Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
Input: tca8418-keypad - switch to using managed resources
Input: tca8418_keypad - increase severity of failures in probe()
Input: tca8418_keypad - move device ID tables closer to where they are used
Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
Input: tca8418_keypad - use a temporary variable for parent device
Input: tca8418_keypad - add support for shared interrupt
Input: tca8418_keypad - add support for device tree bindings
Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
Input: bu21013_ts - add support for Device Tree booting
Input: bu21013_ts - move GPIO init and exit functions into the driver
Input: bu21013_ts - request regulator that actually exists
ARM: ux500: Strip out duplicate touch screen platform information
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
|
|
Pull md update from Neil Brown:
"Mostly just little fixes. Probably biggest part is AVX accelerated
RAID6 calculations."
* tag 'md-3.8' of git://neil.brown.name/md:
md/raid5: add blktrace calls
md/raid5: use async_tx_quiesce() instead of open-coding it.
md: Use ->curr_resync as last completed request when cleanly aborting resync.
lib/raid6: build proper files on corresponding arch
lib/raid6: Add AVX2 optimized gen_syndrome functions
lib/raid6: Add AVX2 optimized recovery functions
md: Update checkpoint of resync/recovery based on time.
md:Add place to update ->recovery_cp.
md.c: re-indent various 'switch' statements.
md: close race between removing and adding a device.
md: removed unused variable in calc_sb_1_csm.
|
|
Merge misc patches from Andrew Morton:
"Incoming:
- lots of misc stuff
- backlight tree updates
- lib/ updates
- Oleg's percpu-rwsem changes
- checkpatch
- rtc
- aoe
- more checkpoint/restart support
I still have a pile of MM stuff pending - Pekka should be merging
later today after which that is good to go. A number of other things
are twiddling thumbs awaiting maintainer merges."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
scatterlist: don't BUG when we can trivially return a proper error.
docs: update documentation about /proc/<pid>/fdinfo/<fd> fanotify output
fs, fanotify: add @mflags field to fanotify output
docs: add documentation about /proc/<pid>/fdinfo/<fd> output
fs, notify: add procfs fdinfo helper
fs, exportfs: add exportfs_encode_inode_fh() helper
fs, exportfs: escape nil dereference if no s_export_op present
fs, epoll: add procfs fdinfo helper
fs, eventfd: add procfs fdinfo helper
procfs: add ability to plug in auxiliary fdinfo providers
tools/testing/selftests/kcmp/kcmp_test.c: print reason for failure in kcmp_test
breakpoint selftests: print failure status instead of cause make error
kcmp selftests: print fail status instead of cause make error
kcmp selftests: make run_tests fix
mem-hotplug selftests: print failure status instead of cause make error
cpu-hotplug selftests: print failure status instead of cause make error
mqueue selftests: print failure status instead of cause make error
vm selftests: print failure status instead of cause make error
ubifs: use prandom_bytes
mtd: nandsim: use prandom_bytes
...
|
|
When compiling efivars.c the build fails with:
CC drivers/firmware/efivars.o
drivers/firmware/efivars.c: In function ‘efivarfs_get_inode’:
drivers/firmware/efivars.c:886:31: error: incompatible types when assigning to type ‘kgid_t’ from type ‘int’
make[2]: *** [drivers/firmware/efivars.o] Error 1
make[1]: *** [drivers/firmware/efivars.o] Error 2
Fix the build error by removing the duplicate initialization of i_uid and
i_gid inode_init_always has already initialized them to 0.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This also removes unnecessary memset call which is immediately overwritten
with random bytes.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Laight <david.laight@aculab.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use prandom_bytes() to fill rss key with pseudo-random bytes.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Laight <david.laight@aculab.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This renames all random32 functions to have 'prandom_' prefix as follows:
void prandom_seed(u32 seed); /* rename from srandom32() */
u32 prandom_u32(void); /* rename from random32() */
void prandom_seed_state(struct rnd_state *state, u64 seed);
/* rename from prandom32_seed() */
u32 prandom_u32_state(struct rnd_state *state);
/* rename from prandom32() */
The purpose of this renaming is to prevent some kernel developers from
assuming that prandom32() and random32() might imply that only
prandom32() was the one using a pseudo-random number generator by
prandom32's "p", and the result may be a very embarassing security
exposure. This concern was expressed by Theodore Ts'o.
And furthermore, I'm going to introduce new functions for getting the
requested number of pseudo-random bytes. If I continue to use both
prandom32 and random32 prefixes for these functions, the confusion
is getting worse.
As a result of this renaming, "prandom_" is the common prefix for
pseudo-random number library.
Currently, srandom32() and random32() are preserved because it is
difficult to rename too many users at once.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: David Laight <david.laight@aculab.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We should return NULL on failure instead of returning a freed pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This version number is printed to the console on module initialization
and is available in sysfs, which is where the userland aoe-version tool
looks for it.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This change only affects experimental AoE storage networks.
It modifies the console message about runt packets detected so that the
AoE major and minor addresses of the AoE target that generated the runt
are mentioned.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
By default, the aoe driver uses any ethernet interface for AoE, but the
aoe_iflist module parameter provides a convenient way to limit AoE
traffic to a specific list of local network interfaces.
This change allows a list to be specified using the comma character as a
separator. For example,
modprobe aoe aoe_iflist=eth2,eth3
Before, it was inconvenient to get the quoting right in shell scripts
when setting aoe_iflist to have more than one network interface.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this change, the aoe driver treats the value zero as special for
the aoe_deadsecs module parameter. Normally, this value specifies the
number of seconds during which the driver will continue to attempt
retransmits to an unresponsive AoE target. After aoe_deadsecs has
elapsed, the aoe driver marks the aoe device as "down" and fails all
I/O.
The new meaning of an aoe_deadsecs of zero is for the driver to
retransmit commands indefinitely.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many AoE targets have four or fewer network ports, but some existing
storage devices have many, and the AoE protocol sets no limit.
This patch allows the use of more than eight remote MAC addresses per AoE
target, while reducing the amount of memory used by the aoe driver in
cases where there are many AoE targets with fewer than eight MAC addresses
each.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This change avoids a race that could result in a NULL pointer derference
following a WARNing from kobject_add_internal, "don't try to register
things with the same name in the same directory."
The problem was found with a test that forgets and discovers an
aoe device in a loop:
while test ! -r /tmp/stop; do
aoe-flush -a
aoe-discover
done
The race was between aoedev_flush taking aoedevs out of the devlist,
allowing a new discovery of the same AoE target to take place before the
driver gets around to calling sysfs_remove_group. Fixing that one
revealed another race between do_open and add_disk, and this patch avoids
that, too.
The fix required some care, because for flushing (forgetting) an aoedev,
some of the steps must be performed under lock and some must be able to
sleep. Also, for discovering a new aoedev, some steps might sleep.
The check for a bad aoedev pointer remains from a time when about half of
this patch was done, and it was possible for the
bdev->bd_disk->private_data to become corrupted. The check should be
removed eventually, but it is not expected to add significant overhead,
occurring in the aoeblk_open routine.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
An AoE target can have multiple network ports used for AoE, and in the
aoe driver, those are tracked by the aoetgt struct. These changes allow
the aoe driver to handle network paths, or aoetgts, that are not working
well, compared to the others.
Paths that do not get responses despite the retransmission of AoE
commands are marked as "tainted", and non-tainted paths are preferred.
Meanwhile, the aoe driver attempts to "probe" the tainted path in the
background by issuing reads of LBA 0 that are padded out to full
(possibly jumbo-frame) size. If the probes get responses, then the path
is "redeemed", and its taint is removed.
This mechanism has been shown to be helpful in transparently handling
and recovering from real-world network "brown outs" in ways that the
earlier "shoot the help-needing target in the head" mechanism could not.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The value returned by the static minor device number number allocator is
the real minor number, so it must be multiplied by the supported number
of partitions per aoedev.
Without this fix the support for systems without udev is incomplete, and
the few users of aoe on such systems will have surprising results when
device nodes names do not match the AoE target.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Because the minor_get and related functions use the return values for
errors, the compiler doesn't know that sysminor will always either 1) be
initialized in aoedev_by_aoeaddr by the call to minor_get, or 2) be
unused as the "goto out" is executed.
This patch avoids the compiler warning.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For some special-purpose systems where udev isn't present, static
allocation of minor numbers is desirable. This update distinguishes
different failure scenarios, to help the user understand what went
wrong.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is no need to call the request handler function in the I/O
completion routine. The user impact of not doing it is a more "nice" aoe
driver that is less susceptible to causing soft lockups.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A misplaced comment was attached to the nout member of the aoetgt. This
change corrects the comment.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The aoe driver will never be waiting for more than aoe_maxout AoE
commands from a given remote network port on an AoE target. Increasing
the cap increases performance. Users can tighten the setting to reduce
the amount of memory used for handling AoE traffic or the network
bandwidth used for AoE.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before the aoe driver was an I/O request handler, it was a
make_request-style block driver. Even so, there was a problem where
sysfs expected a request queue to exist, so one was provided in commit
7135a71b19be ("aoe: allocate unused request_queue for sysfs").
During the transition to the request-handler style, a patch was merged
that was based on a driver without the noop queue, and the noop queue
remained in place after the patch was merged, even though a new
functional queue was introduced by the patch, allocated through
blk_init_queue.
The user impact is a memory leak proportional to the number of AoE
targets discovered. This patch removes the memory leak and cleans up
vestiges of the old do-nothing queue from the aoeblk_gdalloc function.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit f3b8e07af774 ("aoe: commands in retransmit queue use new
destination on failure") omits the copying of the coarse-grained time
when an AoE command was sent during the failover from one destination
MAC address on the AoE target to another.
The coarse-grained timing is only used when the system time changes or
an unlikely length of time has passed since the sending of the AoE
command. Users will not be impacted unless their system clock is very
inaccurate or something unusual (e.g., 10 GbE link reset) happens during
the period when the aoe driver is handling the failure of a port on the
AoE target. Being effected will mean that an AoE target could be
considered "down" too eagerly.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When one remote MAC address isn't working as a destination for AoE
commands, the frames used to track information associated with the AoE
commands are moved to a new aoetgt (defined by the tuple of {AoE major,
AoE minor, target MAC address}).
This patch makes sure that the frames on the queue for retransmits that
need to be done are updated to use the new destination, so that
retransmits will be sent through a working network path.
Without this change, packets on the retransmit queue will be needlessly
retransmitted to the unresponsive destination MAC, possibly causing
premature target failure before there's time for the retransmit timer to
run again, decide to retransmit again, and finally update the destination
to a working MAC address on the AoE target.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These changes improve the accuracy of the decision about whether it's time
to retransmit an AoE command by using the microsecond-resolution
gettimeofday instead of jiffies.
Because the system time can jump suddenly, the decision reverts to using
jiffies if the high-resolution time difference is relatively large.
Otherwise the AoE targets could be considered failed inappropriately.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this bugfix in place the calculation of the criterion for "lateness"
is performed under lock. Without the lock, there is a chance that one of
the non-atomic operations performed on the round trip time statistics
could be incomplete, such that an incorrect lateness criterion would be
calculated.
Without this change, the effect of the bug would be rare unecessary but
benign retransmissions.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The /dev/etherd/err character device provides low-level information about
normal but sometimes interesting AoE command retransmits and "unexpected
responses", i.e., responses for packets that have already been
retransmitted.
This change adds MAC addresses to the messages about unexpected responses,
so that when they occur, it's more easy to determine the network paths to
which they belong.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The aoe driver already had some congestion handling, but it was limited in
its ability to cope with the kind of congestion that can arise on more
complex networks such as those involving paths through multiple ethernet
switches.
Some of the lessons from TCP's history of development can be applied to
improving the congestion control and avoidance on AoE storage networks.
These changes use familar concepts from Van Jacobson's "Congestion
Avoidance and Control" paper from '88, without adding significant
overhead.
This patch depends on an upcoming patch that covers the failover case when
AoE commands being retransmitted are transferred from one retransmit queue
to another. Another upcoming patch increases the timing accuracy.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make the aoe driver follow expected behavior when the user uses ioctl to
get the ATA device identify information, allowing access to model, serial
number, etc.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The userland aoetools package includes an "aoe-stat" command that can
display a "payload size" column when the aoe driver exports this
information. Users can quickly see what amount of user data is
transferred inside each AoE command on the network, network headers
excluded.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The GPFS filesystem is an example of an aoe user that requires the aoe
driver to support I/O request sizes larger than the default. Most users
will not need large I/O request sizes, because they would need to be split
up into multiple AoE commands anyway.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Users sometimes want to cause the aoe driver to forget a particular
previously discovered device when it is no longer online. The aoetools
provide an "aoe-flush" command that users run to perform this
administrative task. The changes below provide the support needed in the
driver.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The ATA over Ethernet config query response contains a "buffer count"
field reflecting the AoE target's capacity to buffer incoming AoE
commands.
By taking the current value of this field into accound, we increase
performance throughput or avoid network congestion, when the value
has increased or decreased, respectively.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Dropped transmits are not common, but when they do occur, increasing
the transmit queue length often helps.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A driver for the DA9055 PMIC. This has a dependency upon the DA9055 MFD
core.
Functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This eliminates having an #ifdef returning NULL for the case when OF is
disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Enabling RTC HW block depends on the default value of TPS65910 register.
In some mode, RTC block is disabled by default.(eg. AM3517 Craneboard) In
this case, RTC_PWDN(RTC power down) bit should be cleared to enable the
RTC HW block.
This patch also works in case that RTC block is active by default, because
there is no side effect even if the bit is updated again.
Tested on AM3517 Craneboard.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Sivaram Nair <sivaramn@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|