| Age | Commit message (Collapse) | Author |
|---|
|
As for SPI, follow "vendor,chip" format 'compatible' string also for
SDIO bus.
Fixes: 0096214a59a7 ("staging: wfx: add support for I/O access")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/96b95d52d0b613065fe655f1d0fe9d7c6adf65fb.1581416843.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current code races in init/exit with interrupt handlers. This is noticed
by the warning below. Fix it by using devres for ordering allocations and
IRQ de/registration.
WARNING: CPU: 0 PID: 827 at drivers/staging/wfx/bus_spi.c:142 wfx_spi_irq_handler+0x5c/0x64 [wfx]
race condition in driver init/deinit
Cc: stable@vger.kernel.org
Fixes: 0096214a59a7 ("staging: wfx: add support for I/O access")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/f0c66cbb3110c2736cd4357c753fba8c14ee3aee.1581416843.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Align to fix multiple warnings of line over 80 characters.
Issue detected by checkpatch tool.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20191113110052.14855-1-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix warning of lines over 80 characters.
Issue detected by checkpatch tool.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20191019140719.2542-3-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix warnings of no space is necessary after a cast.
Issue detected by checkpatch tool.
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20191019140719.2542-2-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most of calls to BUG_ON() could replaced by WARN().
By the way, this patch also try to favor WARN() (that include a comment
about the problem) instead of WARN_ON().
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191008094232.10014-7-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A few tasks remain to be done in order to finish chip initial
configuration:
- configure chip to use multi-tx confirmation (speed up data
transfer)
- configure chip to use wake-up feature (save power consumption
during runtime)
- set hardware configuration (clocks, RF, pinout, etc...) using a
Platform Data Set (PDS) file
On release, driver completely shutdown the chip to save power
consumption.
Documentation about PDS and PDS data for sample boards are available
here[1]. One day, PDS data may find a place in device tree but,
currently, PDS is too much linked with firmware to allowing that.
This patch also add "send_pds" file in debugfs to be able to dynamically
change PDS (only for debug, of course).
[1]: https://github.com/SiliconLabs/wfx-firmware/tree/master/PDS
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20190919142527.31797-15-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
bh_work() is in charge to schedule all HIF message from/to chip.
On normal operation, when an IRQ is received, driver can get size of
next message in control register. In order to save control register
access, when chip send a message, it also appends a copy of control
register after the message (this register is not accounted in message
length declared in message header, but must accounted in bus request).
This copy of control register is called "piggyback".
It also handles a power saving mechanism specific to WFxxx series. This
mechanism is based on a GPIO called "wakeup" GPIO. Obviously, this gpio
is not part of SPI/SDIO standard buses and must be declared
independently (this is the main reason for why SDIO mode try to get
parameters from DT).
When wakeup is enabled, host can communicate with chip only if it is
awake. To wake up chip, there are two cases:
- host receive an IRQ from chip (chip initiate communication): host
just have to set wakeup GPIO before reading data
- host want to send data to chip: host set wakeup GPIO, then wait
for an IRQ (in fact, wait for an empty message) and finally send data
bh_work() is also in charge to track usage of chip buffers. Normally
each request expect a confirmation. However, you can notice that special
"multi tx" confirmation can acknowledge multiple requests at time.
Finally, note that wfx_bh_request_rx() is not atomic (because of
control_reg_read()). So, in SPI mode, hard-irq handler only postpone all
processing to wfx_spi_request_rx().
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20190919142527.31797-8-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A firmware is necessary to run the chip. wfx_init_device() is in charge
of loading firmware on chip and doing low level initialization.
Firmwares for WF200 are available here:
https://github.com/SiliconLabs/wfx-firmware/
Note that firmware are encrypted. Driver checks that key used to encrypt
firmware match with key burned into chip.
Currently, "C0" key is used for production chips.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20190919142527.31797-6-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce bus level communication layer. At this level, 7 registers can
be addressed.
Notice that SPI driver is able to manage chip reset. SDIO mode relies
on an external driver (`mmc-pwrseq`) to reset chip.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20190919142527.31797-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instantiate build infrastructure WFx driver. This driver provides support
for Wifi chipset Silicon Labs WF200 and further:
https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf
This chip support SPI and SDIO bus.
SDIO interface has two particularities:
1. Some parameters may be useful for end user (I will talk about
gpio_wakeup later).
2. The SDIO VID and PID of WF200 are 0000:0001 which are too much
generic to rely on.
So, current code checks VID/PID and looks for a node in DT (since WF200
targets embedded platforms, I don't think it is a problem to rely on
DT). DT can also be used to define to parameters for driver. Currently,
if no node is found, a warning is emitted, but it could be changed in
error.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20190919142527.31797-2-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
