| Age | Commit message (Collapse) | Author |
|---|
|
It was defined a notifier in the csi_state structure that is never
allocated. And besides that it's unregister in the remove, even though
it is a no-op, just remove both.
Fixes: 7807063b862b ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7")
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently v4l2-compliance tool returns the following output:
Compliance test for imx-media-captu device /dev/video0:
Driver Info:
Driver name : imx-media-captu
Card type : imx-media-capture
...
The driver name string is limited to 16 characters, so provide
a shorter name so that we can have a better output.
While at it, use the same shorter name for driver and card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Don't populate the array 'registers' on the stack but instead make it
static const. Makes the object code smaller by 10 bytes.
Before:
text data bss dec hex filename
20138 5196 128 25462 6376 staging/media/imx/imx7-mipi-csis.o
After:
text data bss dec hex filename
20032 5292 128 25452 636c staging/media/imx/imx7-mipi-csis.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
devm_regulator_get may return an error but mipi_csis_phy_init misses
a check for it.
This may lead to problems when regulator_set_voltage uses the unchecked
pointer.
This patch adds a check for devm_regulator_get to avoid potential risk.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If a subdevice is unregistered and then registered again without the
driver being removed and re-probed (which will happen when the media
device is removed and re-probed without also removing/re-probing the
subdevice), media_device_register_entity() is called with a non-zero
entity->num_pads, and then the subdevice's .registered callback calls
media_entity_pads_init(). Thus the subdevice's pad objects are added
to the media device pad list twice, causing list corruption.
One way to fix this would be to create media_entity_pads_destroy(),
and call it in the subdevice's .unregistered callback. But calling
media_entity_pads_init() in the .registered callbacks was done for
legacy reasons and is no longer necessary, so move the call to
media_entity_pads_init() into the subdevice's probe functions. This
fixes the duplicate pad obejcts in the media device pad list.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If the CSI is unregistered and then registered again without the
driver being removed and re-probed (which will happen when the media
device is removed and re-probed without also removing/re-probing the
CSI), the result is the kobject error and backtrace "tried to init an
initialized object". This is because the video device is left in an
initialized state after being unregistered, thus the video device's
underlying kobject is also left in an initialized state when the device
is registered again.
Fix this by moving imx_media_capture_device_init() and _remove()
into csi_registered() and csi_unregistered(). This will create a new
un-initialized video device when the CSI is re-registered. Do this for
all the subdevices that register a capture device.
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This patch fixes a warning by coccicheck:
drivers/staging/media/imx/imx7-mipi-csis.c:973:1-12: WARNING: Use devm_platform_ioremap_resource for state -> regs
Use devm_platform_ioremap_resource helper which wraps platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Jeeeun Evans <jeeeunevans@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
CHECK: Alignment should match open parenthesis
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Now that proper V4L2 pixel formats exist for all 32-bit RGB
permutations, drop support for the poorly defined legacy format
V4L2_PIX_FMT_BGR32.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here is the big staging/iio driver update for 5.4-rc1.
Lots of churn here, with a few driver/filesystems moving out of
staging finally:
- erofs moved out of staging
- greybus core code moved out of staging
Along with that, a new filesytem has been added:
- extfat
to provide support for those devices requiring that filesystem (i.e.
transfer devices to/from windows systems or printers)
Other than that, there a number of new IIO drivers, and lots and lots
and lots of staging driver cleanups and minor fixes as people continue
to dig into those for easy changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (453 commits)
Staging: gasket: Use temporaries to reduce line length.
Staging: octeon: Avoid several usecases of strcpy
staging: vhciq_core: replace snprintf with scnprintf
staging: wilc1000: avoid twice IRQ handler execution for each single interrupt
staging: wilc1000: remove unused interrupt status handling code
staging: fbtft: make several arrays static const, makes object smaller
staging: rtl8188eu: make two arrays static const, makes object smaller
staging: rtl8723bs: core: Remove Macro "IS_MAC_ADDRESS_BROADCAST"
dt-bindings: anybus-controller: move to staging/ tree
staging: emxx_udc: remove local TRUE/FALSE definition
staging: wilc1000: look for rtc_clk clock
staging: dt-bindings: wilc1000: add optional rtc_clk property
staging: nvec: make use of devm_platform_ioremap_resource
staging: exfat: drop unused function parameter
Staging: exfat: Avoid use of strcpy
staging: exfat: use integer constants
staging: exfat: cleanup spacing for casts
staging: exfat: cleanup spacing for operators
staging: rtl8723bs: hal: remove redundant variable n
staging: pi433: Fix typo in documentation
...
|
|
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a single imx-media mem2mem video device that uses the IPU IC PP
(image converter post processing) task for scaling and colorspace
conversion.
On i.MX6Q/DL SoCs with two IPUs currently only the first IPU is used.
The hardware only supports writing to destination buffers up to
1024x1024 pixels in a single pass, arbitrary sizes can be achieved
by rendering multiple tiles per frame.
[slongerbeam@gmail.com: use ipu_image_convert_adjust(), fix
device_run() error handling, add missing media-device header,
unregister and remove the mem2mem device in error paths in
imx_media_probe_complete() and in imx_media_remove(), updated
for sync subdev registration]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: correct two minor checkpatch issues]
[hverkuil-cisco@xs4all.nl: sparse warning: make imx6_media_probe_complete static]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
i.MX7 and i.MX6UL/L have the same CSI controller. So add i.MX6UL/L support
to imx7-media-csi driver.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Not all sensors will be able to guarantee a proper initial state.
This may be either because the driver is not properly written,
or (probably unlikely) because the hardware won't support it.
While the right solution in the former case is to fix the sensor
driver, the real world not always allows right solutions, due to lack
of available documentation and support on these sensors.
Let's relax this requirement, and allow the driver to support stream start,
even if the sensor initial sequence wasn't the expected.
Also improve the warning message to better explain the problem and provide
a hint that the sensor driver needs to be fixed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-43-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a cut&paste error in find_pipeline_entity(). The start entity must be
passed to media_entity_to_video_device() in find_pipeline_entity(), not
pad->entity. The pad is only put to use later, after determining the start
entity is not the entity being searched for.
Fixes: 3ef46bc97ca2 ("media: staging/imx: Improve pipeline searching")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Pull drm updates from Dave Airlie:
"The biggest thing in this is the AMD Navi GPU support, this again
contains a bunch of header files that are large. These are the new AMD
RX5700 GPUs that just recently became available.
New drivers:
- ST-Ericsson MCDE driver
- Ingenic JZ47xx SoC
UAPI change:
- HDR source metadata property
Core:
- HDR inforframes and EDID parsing
- drm hdmi infoframe unpacking
- remove prime sg_table caching into dma-buf
- New gem vram helpers to reduce driver code
- Lots of drmP.h removal
- reservation fencing fix
- documentation updates
- drm_fb_helper_connector removed
- mode name command handler rewrite
fbcon:
- Remove the fbcon notifiers
ttm:
- forward progress fixes
dma-buf:
- make mmap call optional
- debugfs refcount fixes
- dma-fence free with pending signals fix
- each dma-buf gets an inode
Panels:
- Lots of additional panel bindings
amdgpu:
- initial navi10 support
- avoid hw reset
- HDR metadata support
- new thermal sensors for vega asics
- RAS fixes
- use HMM rather than MMU notifier
- xgmi topology via kfd
- SR-IOV fixes
- driver reload fixes
- DC use a core bpc attribute
- Aux fixes for DC
- Bandwidth calc updates for DC
- Clock handling refactor
- kfd VEGAM support
vmwgfx:
- Coherent memory support changes
i915:
- HDR Support
- HDMI i2c link
- Icelake multi-segmented gamma support
- GuC firmware update
- Mule Creek Canyon PCH support for EHL
- EHL platform updtes
- move i915.alpha_support to i915.force_probe
- runtime PM refactoring
- VBT parsing refactoring
- DSI fixes
- struct mutex dependency reduction
- GEM code reorg
mali-dp:
- Komeda driver features
msm:
- dsi vs EPROBE_DEFER fixes
- msm8998 snapdragon 835 support
- a540 gpu support
- mdp5 and dpu interconnect support
exynos:
- drmP.h removal
tegra:
- misc fixes
tda998x:
- audio support improvements
- pixel repeated mode support
- quantisation range handling corrections
- HDMI vendor info fix
armada:
- interlace support fix
- overlay/video plane register handling refactor
- add gamma support
rockchip:
- RX3328 support
panfrost:
- expose perf counters via hidden ioctls
vkms:
- enumerate CRC sources list
ast:
- rework BO handling
mgag200:
- rework BO handling
dw-hdmi:
- suspend/resume support
rcar-du:
- R8A774A1 Soc Support
- LVDS dual-link mode support
- Additional formats
- Misc fixes
omapdrm:
- DSI command mode display support
stm
- fb modifier support
- runtime PM support
sun4i:
- use vmap ops
vc4:
- binner bo binding rework
v3d:
- compute shader support
- resync/sync fixes
- job management refactoring
lima:
- NULL pointer in irq handler fix
- scheduler default timeout
virtio:
- fence seqno support
- trace events
bochs:
- misc fixes
tc458767:
- IRQ/HDP handling
sii902x:
- HDMI audio support
atmel-hlcdc:
- misc fixes
meson:
- zpos support"
* tag 'drm-next-2019-07-16' of git://anongit.freedesktop.org/drm/drm: (1815 commits)
Revert "Merge branch 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux into drm-next"
Revert "mm: adjust apply_to_pfn_range interface for dropped token."
mm: adjust apply_to_pfn_range interface for dropped token.
drm/amdgpu/navi10: add uclk activity sensor
drm/amdgpu: properly guard the generic discovery code
drm/amdgpu: add missing documentation on new module parameters
drm/amdgpu: don't invalidate caches in RELEASE_MEM, only do the writeback
drm/amd/display: avoid 64-bit division
drm/amdgpu/psp11: simplify the ucode register logic
drm/amdgpu: properly guard DC support in navi code
drm/amd/powerplay: vega20: fix uninitialized variable use
drm/amd/display: dcn20: include linux/delay.h
amdgpu: make pmu support optional
drm/amd/powerplay: Zero initialize current_rpm in vega20_get_fan_speed_percent
drm/amd/powerplay: Zero initialize freq in smu_v11_0_get_current_clk_freq
drm/amd/powerplay: Use memset to initialize metrics structs
drm/amdgpu/mes10.1: Fix header guard
drm/amd/powerplay: add temperature sensor support for navi10
drm/amdgpu: fix scheduler timeout calc
drm/amdgpu: Prepare for hmm_range_register API change (v2)
...
|
|
When the upstream endpoint is neither a mux nor a CSI2 module, just get
the source pad directly upstream from the CSI.
Reported-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Retask imx_media_fill_default_mbus_fields() to try colorimetry parameters,
renaming it to to imx_media_try_colorimetry(), and call it at both sink and
source pad try_fmt's. The unrelated check for uninitialized field value is
moved out to appropriate places in each subdev try_fmt.
The IC now supports Rec.709 and BT.601 Y'CbCr encoding, and both limited
and full range quantization for both YUV and RGB space, so allow those
for pipelines that route through the IC.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Only providing the input and output RGB/YUV space to the IC task init
functions is not sufficient. To fully characterize a colorspace
conversion, the Y'CbCr encoding standard, and quantization also
need to be specified.
Define a 'struct ipu_ic_colorspace' that includes all the above.
This allows to actually enforce the fact that the IC:
- can only encode to/from YUV and RGB full range. A follow-up patch will
remove this restriction.
- can only encode using BT.601 standard. A follow-up patch will add
Rec.709 encoding support.
The determination of the CSC coefficients based on the input/output
'struct ipu_ic_colorspace' are moved to a new exported function
ipu_ic_calc_csc(), and 'struct ic_csc_params' is exported as
'struct ipu_ic_csc_params'. ipu_ic_calc_csc() fills a 'struct ipu_ic_csc'
with the input/output 'struct ipu_ic_colorspace' and the calculated
'struct ic_csc_params' from those input/output colorspaces.
The functions ipu_ic_task_init(_rsc)() now take a filled 'struct
ipu_ic_csc'.
The existing CSC coefficient tables and ipu_ic_calc_csc() are moved
to a new module ipu-ic-csc.c. This is in preparation for adding more
coefficient tables for limited range quantization and more encoding
standards.
The existing ycbcr2rgb and inverse rgb2ycbcr tables defined the BT.601
Y'CbCr encoding coefficients. The rgb2ycbcr table specifically described
the BT.601 encoding from full range RGB to full range YUV. Table
comments have been added in ipu-ic-csc.c to make this more clear.
The ycbcr2rgb inverse table described encoding YUV limited range to RGB
full range. To be consistent with the rgb2ycbcr table, this table is
converted to YUV full range to RGB full range, and the comments are
expanded in ipu-ic-csc.c.
The ic_csc_rgb2rgb table was just an identity matrix, so it is renamed
'identity' in ipu-ic-csc.c.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
[p.zabel@pengutronix.de: removed a superfluous blank line]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
enabled"
Commit 020bc7354a6e ("media: staging/imx: Allow driver to build
if COMPILE_TEST is enabled") incorrectly assumed that the imx media
driver had no build time dependency with IMX_IPUV3_CORE.
Building on x86_64 without IMX_IPUV3_CORE causes lots of build errors
such as:
All these definitions come from the imx ipu3 core driver, so make
sure that imx media depends on IMX_IPUV3_CORE.
This reverts commit 020bc7354a6ebec980e0aedf5bedf57b42f93aca.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In case of ioremap failure, the core code will take care of printing
the error message, so there is no need for having a local error
message in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CSI registers are 32-bit, so using u32 type is more suitable
for storing the values from register reads.
Switch from 'unsigned long' to 'u32' type.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Currently there is a macro for reading and another macro for writing
to the CSI registers.
Functions can do parameter type checking, which leads to a safer code,
so switch from macro to function implementation.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Checkpatch reports an extra blank line, so remove such unneeded
line.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
There is no need for initializing the 'ret' variable as it will
be assigned at:
ret = mipi_csis_parse_dt(pdev, state);
Remove the unneeded initialization.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Currently the return value from clk_bulk_prepare_enable() is checked,
but it is not propagate it in the case of failure.
Fix it and also move the error message to the caller of
mipi_csis_clk_enable().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The imx_media_pipeline_pad() function return NULL pointers on error, it
never returns error pointers.
Fixes: 3ef46bc97ca2 ("media: staging/imx: Improve pipeline searching")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
imx7_csi_enable() always return 0 and its return value is never checked,
so convert it to void.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Remove unneeded 'break' right after the 'return' statement as
pointed out by checkpatch.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In the case of devm_request_irq() failure, let's propagate the real error
code instead of a fake one.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In the case of platform_get_irq() failure, let's propagate the real error
code instead of a fake one.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
While at it, propagate the real error value in case of
devm_platform_ioremap_resource() failure.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
As per the i.MX7D Reference Manual only the MCLK is used for
the CSI block, so only handle this single clock.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The media device is already available via multiple methods, there is no
need to set driver data for v4l2_dev to the media device.
In imx_media_link_notify(), get media device from link->graph_obj.mdev.
In imx_media_capture_device_register(), get media device from
v4l2_dev->mdev.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Export find_pipeline_pad(), renaming to imx_media_pipeline_pad(), and
extend its functionality to allow searching for video devices in the
enabled pipeline in addition to sub-devices.
As part of this:
- Rename imx_media_find_mipi_csi2_channel() to
imx_media_pipeline_csi2_channel().
- Remove imx_media_find_upstream_pad(), it is redundant now.
- Rename imx_media_find_upstream_subdev() to imx_media_pipeline_subdev()
with an additional boolean argument for searching upstream or downstream.
- Add imx_media_pipeline_video_device() which is analogous to
imx_media_pipeline_subdev() but searches for video devices.
- Remove imxmd pointer arg from all of the functions above, it was
never used in those functions. With that change the i.MX5/6 CSI,
VDIC, and IC sub-devices no longer require the media_device.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Re-organize modules, and which objects are linked into those modules, so
that:
- imx6-media (renamed from imx-media) is the media driver module for
imx5/6 only, and has no symbol exports.
- imx6-media-csi (renamed from imx-media-csi) is the subdev driver
module for imx5/6 CSI. It is now linked direcly with imx-media-fim,
since only the imx5/6 CSI makes use of the frame interval monitor.
- imx-media-common now only contains common code between imx5/6 and imx7
media drivers. It contains imx-media-utils, imx-media-of,
imx-media-dev-common, and imx-media-capture. In order to acheive that,
some functions common to imx5/6 and imx7 have been moved out of
imx-media-dev.c and into imx-media-dev-common.c.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Don't propagate the source pad format to the connected capture device.
It's now the responsibility of userspace to call VIDIOC_S_FMT on the
capture device to ensure the capture format and compose rectangle
are compatible with the connected source. To check this, validate
the capture format with the source before streaming starts.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
capture_device_set_format"
Revert this commit, as imx_media_capture_device_set_format() will be
removed. The arguments to mx_media_mbus_fmt_to_pix_fmt() and
imx_media_capture_device_set_format() in imx7_csi_set_fmt() are also
reverted.
This reverts commit 5964cbd8692252615370b77eb96764dd70c2f837.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Move imx_media_add_video_device() into imx_media_capture_device_register().
Also the former has no error conditions to convert to void.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Allocate and free a DMA coherent buffer in imx_media_alloc/free_dma_buf()
from the given device. This allows DMA alloc and free using a device
that is backed by real hardware, which for the imx5/6/7 CSI is the CSI
unit, and for the internal IPU sub-devices, is the parent IPU.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Because the IPU sub-devices VDIC and IC are not present in the
device-tree, platform devices were created for them instead. This
allowed these sub-devices to be added to the media device's async
notifier and registered asynchronously along with the other
sub-devices that do have a device-tree presence (CSI and devices
external to the IPU and SoC).
But that approach isn't really necessary. The IPU sub-devices don't
actually require a backing device (sd->dev is allowed to be NULL).
And that approach can't get around the fact that the IPU sub-devices
are not part of a device hierarchy, which makes it awkward to retrieve
the parent IPU of these devices.
By registering them synchronously, they can be registered from the CSI
async bound notifier, so the init function for them can be given the CSI
subdev, who's dev->parent is the IPU. That is a somewhat cleaner way
to retrieve the parent IPU.
So convert to synchronous registration for the VDIC and IC task
sub-devices, at the time a CSI sub-device is bound. There is no longer
a backing device for them (sd->dev is NULL), but that's ok. Also
set the VDIC/IC sub-device owner as the IPU, so that a reference can
be taken on the IPU module.
Since the VDIC and IC task drivers are no longer platform drivers,
they are now statically linked to imx-media module.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The imx6-specific subdevs that register a capture device will no
longer hold a reference to the media device, so this commit must be
reverted.
This reverts commit 16204b8a1c1af77725533b77936e6c73953486ae.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
fix below warning reported by coccichec
drivers/staging/media/imx/imx-media-capture.c:617:5-8: Unneeded
variable: "ret". Return "0" on line 630
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Setting the media entity pads after the async register subdev can be
racy with probe complete callback. So, make sure that the media pads
are initialized before the probe complete is called.
For that move the media entity pads initialization to the registered
subdev internal operation.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The driver has runtime but no build time dependency with IMX_IPUV3_CORE,
so can be built for testing purposes if COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some fixes for some platform drivers (rockchip, atmel, omap, daVinci,
tegra-cec, coda and rcar).
Also includes a fix on one of the V4L2 uAPI doc, explaining a border
case"
* tag 'media/v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: rockchip/vpu: Fix/re-order probe-error/remove path
media: rockchip/vpu: Initialize mdev->bus_info
media: rockchip/vpu: Get vdev from the file arg in vidioc_querycap()
media: rockchip/vpu: Add missing dont_use_autosuspend() calls
media: rockchip/vpu: Do not request id 0 for our video device
media: tegra-cec: fix cec_notifier_parse_hdmi_phandle return check
media: davinci/vpbe: array underflow in vpbe_enum_outputs()
media: field-order.rst: clarify FIELD_ANY and FIELD_NONE
media: staging/imx: add media device to capture register
media: rcar-csi2: Propagate the FLD signal for NTSC and PAL
media: rcar-csi2: restart CSI-2 link if error is detected
media: omap_vout: potential buffer overflow in vidioc_dqbuf()
media: coda: fix unset field and fail on invalid field in buf_prepare
media: atmel: atmel-isc: fix asd memory allocation
media: atmel: atmel-isc: fix INIT_WORK misplacement
media: atmel: atmel-isc: limit incoming pixels per frame
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove the deprecated Zoran driver from staging
- new I2C driver: ST MIPID02 CSI-2 camera bridge
- new platform driver: Amlogic Meson AO CEC G12A Controller
- add support for USB audio via the media controller
- au0828 driver is now supported via the media controller on both on
media and on usbaudio
- new kernel test for the media device allocator
- add support for stateless decoder at vicodec driver
- lots of other driver improvements fixes and cleanups
* tag 'media/v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (218 commits)
media: dt-bindings: aspeed-video: Add missing memory-region property
media: platform: Aspeed: Make reserved memory optional
media: platform: Aspeed: Remove use of reset line
media: stm32-dcmi: return appropriate error codes during probe
media: vsp1: Add support for missing 16-bit RGB555 formats
media: vsp1: Add support for missing 16-bit RGB444 formats
media: vsp1: Add support for missing 32-bit RGB formats
media: v4l: Add definitions for missing 16-bit RGB555 formats
media: v4l: Add definitions for missing 16-bit RGB4444 formats
media: v4l: Add definitions for missing 32-bit RGB formats
media: zoran: remove deprecated driver
media: MAINTAINERS: Update AO CEC with ao-cec-g12a driver
media: platform: meson: Add Amlogic Meson G12A AO CEC Controller driver
media: dt-bindings: media: meson-ao-cec: Add G12A AO-CEC-B Compatible
media: cros-ec-cec: decrement HDMI device refcount
media: seco-cec: decrement HDMI device refcount
media: tegra_cec: use new cec_notifier_parse_hdmi_phandle helper
media: stih_cec: use new cec_notifier_parse_hdmi_phandle helper
media: s5p_cec: use new cec_notifier_parse_hdmi_phandle helper
media: meson: ao-cec: use new cec_notifier_parse_hdmi_phandle helper
...
|
|
When register the capture media device it is assumed that the device
data is the media device. In the imx6 case is but in the imx7 is not
case. The device data is the csi structure.
Add the explicit argument of the media device that we want to
associate with the capture device.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
