| Age | Commit message (Collapse) | Author |
|---|
|
There are two types of io errors when processing alert event.
a) the Master detects an ALERT status for e.g. a jack event and
invokes the implementation-defined function in the Slave driver to
check the jack status. At this time the codec is just suspended, so io
registers can't be accessed.
b) when waking up from clock stop mode1 state, where the bus needs a
complete re-enumeration, Slave registers can't be accessed until the
enumeration is complete.
This patch resumes the Slave device and waits for initialization
complete when processing slave alert event, so that registers on the
Slave can be accessed without timeouts or io errors.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Before removing the slave device, disable pm_runtime to prevent any
race condition with the resume being executed after the bus and slave
devices are removed.
Since this pm_runtime_disable() is handled in common routines,
implementations of Slave drivers do not need to call it in their
.remove() routine.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When resuming with a bus reset, we need to re-enumerate and restart
from UNATTACHED. The helper added in this patch helps implement a more
robust state machine avoiding race conditions on resume.
The unattach request is stored and will be used by Slave drivers, if
needed: Intel validation exposed a corner case where the Slave device
may transition to D3 when streaming stops, but streaming restarts
before the Master transitions to D3. In that case, the Slave status
was not cleared as UNATTACHED by the Master resuming, and the
wait_for_completion will time out.
When the slave resumes, it can check if a Master-initiated
re-enumeration and initialization took place and skip the
wait_for_completion() if there is no reason to wait.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
While handling the Device0, we can safely use sdw_write_no_pm.
This move will also helps us track that all other usages of
sdw_write() happen when the Slave is already enumerated.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for pm_runtime with the appropriate error checks for
sdw_write/read functions, e.g. when pm_runtime is not supported.
Also expose internal functions without pm_runtime support, which are
required to perform any sort of suspend/resume operation, as well as
any enumeration tasks.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Waiting for the enumeration to be complete may not be enough for a
Slave driver, there is a possible race condition between resume
operations and initializations handled in an interrupt thread, which
can results in settings not being fully restored after system or
pm_runtime resume.
This patch builds on the changes added for enumeration_complete,
init_completion() is called when the Slave device becomes UNATTACHED,
as done with enumeration_complete.
The difference with the enumeration_complete case is that complete()
is signaled after the Slave device is fully initialized after the
.update_status() callback is called.
A Slave device driver can decide to wait on either of the two
complete() cases, depending on its initialization code and
requirements.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This patch adds the signaling needed for Slave drivers to wait until
the enumeration completes so that race conditions when issuing
read/write commands are avoided. The calls for wait_for_completion()
will be added in codec drivers in follow-up patches.
The order between init_completion() and complete() is deterministic,
the Slave is marked as UNATTACHED either during a Master-initiated
HardReset, or when the hardware detects the Slave no longer reports as
ATTACHED.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver probe takes care of basic initialization and is invoked
when a Slave becomes attached, after a match between the Slave DevID
registers and ACPI/DT entries.
The update_status callback is invoked when a Slave state changes,
e.g. when it is assigned a non-zero Device Number and it reports with
an ATTACHED/ALERT state.
The state change detection is usually hardware-based and based on the
SoundWire frame rate (e.g. double-digit microseconds) while the probe
is a pure software operation, which may involve a kernel module
load. In corner cases, it's possible that the state changes before the
probe completes.
This patch suggests the use of wait_for_completion to avoid races on
startup, so that the update_status callback does not rely on invalid
pointers/data structures.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/87o8tvjcbc.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make sure all calls to the SoundWire stream API are done and involve
callback. Also kfree the stream name.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The sdw stream is allocated and stored in dai to share the sdw runtime
information.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The existing code does not expose a trigger callback, which is very
much required for streaming.
The SoundWire stream is enabled and disabled in trigger function.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The existing code does not expose a prepare operation, which is very
much needed to deal with underflow and resume operations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There are too many fields called 'res' so add prefix to make it easier
to track what the structures are.
Pure rename, no functionality change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In the Intel QA multi-pipelines test case, there are two pipelines for
playback and capture on the same bus. The test fails with an error
when setting port params:
[ 599.224812] rt711 sdw:0:25d:711:0: invalid dpn_prop direction 1 port_num 0
[ 599.224815] sdw_program_slave_port_params failed -22
[ 599.224819] intel-sdw sdw-master-0: Program transport params failed: -22
[ 599.224822] intel-sdw sdw-master-0: Program params failed: -22
[ 599.224828] sdw_enable_stream: SDW0 Pin2-Playback: done
This problem is root-caused to the programming of the capture stream
ports while it is not yet prepared, the calling sequence is:
(1) hw_params for playback. The playback stream provide the port
information to Bus.
(2) stream_prepare for playback, Transport and port parameters
are computed for playback.
(3) hw_params for capture. The capture stream provide the port
information to Bus, but it has not been prepared so is not
accounted for in the bandwidth allocation.
(4) stream_enable for playback. Program transport and port parameters
for all masters and slaves. Since the transport and port parameters
are not computed for capture stream, sdw_program_slave_port_params
will generate a error when setting port params for capture.
in step (4), we should only program the ports for the stream that have
been prepared. A stream that is only in CONFIGURED state should be
ignored, its ports will be programmed when it becomes PREPARED.
Tested on Comet Lake.
GitHub issue: https://github.com/thesofproject/linux/issues/1637
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The existing code will unconditionally return after dealing with the
first Slave on a link. This return should only happen when there is
an error case.
Tested on Comet Lake platform.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
After a system suspend, the ALSA/ASoC core will invoke the .prepare()
callback and a TRIGGER_START when INFO_RESUME is not supported.
Likewise, when an underflow occurs, the .prepare callback will be invoked.
In both cases, the stream can be in DISABLED mode, and will transition
into the PREPARED mode. We however don't want the bus bandwidth to be
recomputed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We don't need to prepare the stream again if the stream is already
prepared.
sdw_prepare_stream() could be called multiple times without calling
sdw_deprepare_stream(). We call sdw_prepare_stream() in the prepare
dai ops and sdw_deprepare_stream() in the hw_free dai ops. If an xrun
happens, sdw_prepare_stream() will be called but
sdw_deprepare_stream() will not, which results in an imbalance and an
invalid total bandwidth.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The state machine and notes don't accurately explain or allow
transitions from STREAM_DEPREPARED and STREAM_DISABLED.
Add more explanations and allow for more transitions as a result of a
trigger_stop(), trigger_suspend() and prepare(), depending on the
ALSA/ASoC layer behavior defined by the INFO_RESUME and INFO_PAUSE
flags.
Also add basic checks to help debug inconsistent states and illegal
state machine transitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix previous update, bad git merge likely. oops.
Fixes: 39737a313085fa ("soundwire: cadence: update kernel-doc parameter descriptions")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114233124.13888-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Somehow Intel folks were confused, the property is 2x what the mclk
frequency actually is (checked the actual bus frequency with a scope)
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113231129.19049-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If the programming of the dev_number fails due to an IO error, a new
device_number will be assigned, resulting in a leak.
Make sure we only assign a device_number once per Slave device.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113225637.17313-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix cppcheck warning:
drivers/soundwire/cadence_master.c:992:9: style: Variable 'offset' is
assigned a value that is never used. [unreadVariable]
offset += stream->num_out;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113211025.27973-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
make W=1 reports inconsistencies with parameter descriptions, fix
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113211025.27973-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Qualcomm SoundWire Master controller is present in most Qualcomm SoCs
either integrated as part of WCD audio codecs via slimbus or
as part of SOC I/O.
This patchset adds support to a very basic controller which has been
tested with WCD934x SoundWire controller connected to WSA881x smart
speaker amplifiers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200113132153.27239-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Before checking for the presence of Device0, we first need to clean-up
the internal state of Slaves that are no longer attached.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When a Slave reports multiple status in the sticky bits, find the
latest configuration from the mirror of the PING frame status and
update the status directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Config only needs to be updated when setting MCP_Config, MCP_Control
and MCP_CmdCtrl to make these register setting effective. When updating
config in master, master will communicate with slave to update status.
Communication will be failed when masters and slaves are in clock stop
state, and this unnecessary config update makes interrupt setting failed.
Tested on Comet Lake with soundwire enabled
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add the type of command, device number, register offset and length to
reverse engineer what caused the issue.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
make sure all interrupts status are cleared before enabling interrupt
so that there is no unexpected interrupt triggered.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If somehow we read the interrupt status while the IP is not powered
the result is probably undefined or 0xffffffff. We do know that some
of the bits are reserved and read as zero, so use as a filter to
discard invalid configurations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Only keep pr_err to flag critical configuration errors that will
typically only happen during system integration.
For errors on prepare/deprepare/enable/disable, the caller can do a
much better job with more information on the DAI and device that
caused the issue.
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200108175438.13121-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The SoundWire DAIs for Intel platform are created in
drivers/soundwire/intel.c, while the communication with the Intel DSP
is all controlled in soc/sof/intel
When the DAI status changes, a callback is used to bridge the gap
between the two subsystems.
The naming of the existing 'config_stream' callback does not map well
with any of ALSA/ASoC concepts. This patch renames it as
'params_stream' to be more self-explanatory.
A new 'free_stream' callback is added in case any resources allocated
in the 'params_stream' stage need to be released. In the SOF
implementation, this is used in the hw_free case to release the DMA
channels over IPC.
These two callbacks now rely on structures which expose the link_id
and alh_stream_id (required by the firmware IPC), instead of a list of
parameters. The 'void *' definitions are changed to use explicit
types, as suggested on alsa-devel during earlier reviews.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The current interfaces between ASoC and SoundWire are limited by the
platform_device infrastructure to an init() and exit() (mapped to the
platform driver.probe and .remove)
To help with the platform detection, machine driver selection and
management of power dependencies between DSP and SoundWire IP, the
ASoC side requires:
a) an ACPI scan helper, to report if any devices are exposed in the
DSDT tables, and if any links are disabled by the BIOS.
b) a probe helper that allocates the resources without actually
starting the bus.
c) a startup helper which does start the bus when all power
dependencies are settled.
d) an exit helper to free all resources
e) an interrupt_enable/disable helper, typically invoked after the
startup helper but also used in suspend routines.
This patch moves all required interfaces to sdw_intel.h, mainly to
allow SoundWire and ASoC parts to be merged separately once the header
files are shared between trees.
To avoid compilation issues, the conflicts in intel_init.c are blindly
removed. This would in theory prevent the code from working, but since
there are no users of the Intel Soundwire driver this has no
impact. Functionality will be restored when the removal of platform
devices is complete.
Support for SoundWire + SOF builds will only be provided once all the
required pieces are upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We need the char/misc driver fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The uniqueID is useful when there are two or more devices of the same
type (identical manufacturer ID, part ID) on the same link.
When there is a single device of a given type on a link, its uniqueID
is irrelevant. It's not uncommon on actual platforms to see variations
of the uniqueID, or differences between devID registers and ACPI _ADR
fields.
This patch suggests a filter on startup to identify 'single' devices
and tag them accordingly. The uniqueID is then not used for the probe,
and the device name omits the uniqueID as well.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022234808.17432-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Simplify the loop with a helper. The only functionality change is that
we continue the loop even with an ACPI error.
Follow-up patches will build on this change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022234808.17432-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The previous formula is incorrect for PDI0/1, the mapping is not
linear but has a discontinuity between PDI1 and PDI2.
This change has no effect on PCM PDIs (same mapping).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022232948.17156-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The use of clock stop is not a requirement, the IP can e.g. be
completely power gated and not detect any wakes while in s2idle/deep
sleep.
For now clock-stop is not supported anyways so the control parameter
is always false. This will be revisited when we add clock stop.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Prepare for future PM support and fix error handling by disabling
interrupts as needed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Move code to helper for reuse in power management routines
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Provide debugfs capability to kick link and devices into hard-reset
(as defined by MIPI). This capability is really useful when some
devices are no longer responsive and/or to check the software handling
of resynchronization.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Multiple changes squashed in single patch to avoid tick-tock effect
and avoid breaking compilation/bisect
1. Per the hardware documentation, all changes to MCP_CONFIG,
MCP_CONTROL, MCP_CMDCTRL and MCP_PHYCTRL need to be validated with a
self-clearing write to MCP_CONFIG_UPDATE. Add a helper and do the
update when the CONFIG is changed.
2. Move interrupt enable after interrupt handler registration
3. Add a new helper to start the hardware bus reset with maximum duration
to make sure the Slave(s) correctly detect the reset pattern and to
ensure electrical conflicts can be resolved.
4. flush command FIFOs
Better error handling will be provided after interrupt disable is
provided in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
fix cppcheck warning:
[drivers/soundwire/slave.c:145]: (warning) %x in format string (no. 1)
requires 'unsigned int *' but the argument type is 'signed int *'.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022233147.17268-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit df72b7192119 ("soundwire: intel: add missing headers for
cross-compilation") tried to fix cross compilation but erroneously used
wrong header in one of the file. Fix it by using correct io.h header.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: df72b7192119 ("soundwire: intel: add missing headers for cross-compilation")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There are two issues, likely copy/paste:
1. Use cdns->pcm.num_in instead of stream_num_in for consistency with
the rest of the code. This was not detected earlier since platforms did
not have input-only PDIs.
2. use the correct offset for bi-dir PDM, based on IN and OUT
PDIs. Again this was not detected since PDM was not supported earlier.
Reported-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
PDI number should match dai->id, there is no need to track if a PDI is
allocated or not.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
PDI0/1 are reserved for Bulk and filtered out in the existing code.
That leads to endless confusions on whether the index is the raw or
corrected one. In addition we will need support for Bulk at some point
so it's just simpler to expose those PDIs and not use it for now than
try to be smart unless we have to remove the smarts.
This patch requires a topology change to use PDIs starting at offset 2
explicitly.
Note that there is a known discrepancy between hardware documentation
and what ALH stream works in practice, future fixes are likely.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The existing Linux code uses a 1:1 mapping between ports and PDIs, but
still has an independent allocation of ports and PDIs.
Let's simplify the code and remove the port layer by only using PDIs.
This patch does not change any functionality, just removes unnecessary
code.
This will also allow for further simplifications where the PDIs are
not dynamically allocated but instead described in a topology file.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We will create dai widget in SOF.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
