| Age | Commit message (Collapse) | Author |
|---|
|
GPIO 0 is a valid GPIO so allow using it as external control for
S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
GPIO 0 is a valid GPIO so allow using it as external control for
regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
An issue was discovered with tps65090 where sometimes the FETs
wouldn't actually turn on when requested (they would report
overcurrent). The most problematic FET was the one used for the LCD
backlight on the Samsung ARM Chromebook (FET1). Problems were
especially prevalent when the device was plugged in to AC power (when
the backlight voltage was higher).
Mitigate the problem by adding retries on the enables of the FETs,
which works around the problem fairly effectively.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).
The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
It is more idiomatic to process things relating to the regulator in its
driver. This patch moves both processing of device tree relating to the
regulator and checking if the regulator is external from arizona-core
into the regulator driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Rather than requiring individual drivers to put the of_nodes returned
from of_regulator_match use devres to put them. This also has the
benefit it makes the life-time of the of_nodes match the lifetime of
the init data also contained in the of_regulator_match structure, which
seems more consistent.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The voltages in LDO1_VSEL_table are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The tps65090 regulator allows you to specify how long you want it to
wait before detecting an overcurrent condition. Allow specifying that
through the device tree (or through platform data).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Now this driver uses devm_regulator_register() so we don't need to save rdev
pointer to tps->rdev[i] for cleanup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since commit ca5d1b3524b4d
"regulator: helpers: Modify helpers enabling multi-bit control",
we can set enable_val setting for device that use multiple bits for control
when using regmap enable/disable/bypass ops.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch converts this driver to use the regmap helper functions provided by
regulator core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The is_enabled implementation is wrong in some cases:
e.g. for pbias_mmc_omap5: enable_mask is : BIT(27) | BIT(25) | BIT(26)
However, pbias_regulator_enable() only sets BIT(27) | BIT(26) bits.
So is_enabled callback will always return false in this case.
Fix the logic to compare the register value with info->enable rather than
info->enable_mask.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add support for external control over GPIO for LDO10, LDO11 and LDO12
S2MPS14 regulators. External control can be turned on by writing 0x0 to
control register which in case of other regulators is used for disabling
them. These LDO10-LDO12 regulators can be disabled only by I2C GPIO or
PWREN pin so the patch actually allows proper way of disabling them.
Additionally the GPIO control has two benefits:
- It is faster than toggling it over I2C bus.
- It allows disabling the regulator during suspend to RAM; The AP will
enable it during resume.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Refactor code for parsing DTS to increase a little code readability. The
behaviour should not change.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Don't store pointer to regulator_dev returned by
devm_regulator_register() in state container. It isn't used anywhere
outside of probe.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Currently the regulator core does not take an additional reference to
the of_node it is passed. This means that the caller must ensure that
the of_node is valid for the duration of the regulator's existance.
It is reasonable for the framework to assume it is passed a valid
of_node but seems onerous for it to assume the caller will keep the node
valid for the life-time of the regulator, especially when
devm_regulator_register is used and there will likely be no code in the
driver called at the point it would be safe to put the of_node.
This patch adds an additional of_node_get when the regulator is
registered and an of_node_put when it is unregistered in the core. This
means individual drivers are free to put their of_node references at the
end of probe letting the regulator core handling it from there. This
simplifies code on the driver side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As of_regulator_match will take an of_node reference to each matched
regulator, it makes sense to provide a helper to put all those
references. This patch does that.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Currently, of_regulator_match does not increment the reference count of
the of_nodes it takes new references to. This could cause the node
pointer held to be invalid, by the time it is passed to the regulator
core. This patchs adds an of_node_get when we copy each of_node pointer
into the match structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
AXP202 and AXP209 come with two synchronous step-down DC-DCs and five
LDOs. This patch introduces basic support for those regulators.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few driver specific fixes that have come in over the merge window,
all only relevant for the specific driver"
* tag 'regulator-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: bcm590xx: Set n_voltages for linear reg
regulator: s5m8767: Fix carried over ena_gpio assignment
regulator: s2mps11: Don't check enable_shift before setting enable ramp rate
regulator: s2mpa01: Don't check enable_shift before setting enable ramp rate
|
|
and 'regulator/fix/s5m8767' into regulator-linus
|
|
Fix the macro used to define linear range regulators to include the
number of voltages.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
|
|
During registration of regulators if external control for regulator was
set in DTS the ena_gpio and ena_gpio_flags fields of regulator_config
were set to proper values.
However the same regulator_config was used in next iterations of loop so
the ena_gpio fields carried over to next regulators.
The issue was not observed as ena_gpio is supported only for Buck9
regulator which is often the last regulator parsed from DTS.
Be sure to clear ena_gpio config fields before registering the
regulator.
Fixes: ee1e0994ab1bd (regulator: s5m8767: Use GPIO for controlling Buck9/eMMC)
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science -- mostly documentation and comment updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
sparse: fix comment
doc: fix double words
isdn: capi: fix "CAPI_VERSION" comment
doc: DocBook: Fix typos in xml and template file
Bluetooth: add module name for btwilink
driver core: unexport static function create_syslog_header
mmc: core: typo fix in printk specifier
ARM: spear: clean up editing mistake
net-sysfs: fix comment typo 'CONFIG_SYFS'
doc: Insert MODULE_ in module-signing macros
Documentation: update URL to hfsplus Technote 1150
gpio: update path to documentation
ixgbe: Fix format string in ixgbe_fcoe.
Kconfig: Remove useless "default N" lines
user_namespace.c: Remove duplicated word in comment
CREDITS: fix formatting
treewide: Fix typo in Documentation/DocBook
mm: Fix warning on make htmldocs caused by slab.c
ata: ata-samsung_cf: cleanup in header file
idr: remove unused prototype of idr_free()
|
|
Current code misses updating the register when enable_shift is 0.
e.g. S2MPS11_BUCK9_RAMP_SHIFT and S2MPS11_BUCK6_RAMP_EN_SHIFT are 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current code misses updating the register when enable_shift is 0.
e.g. S2MPA01_BUCK4_RAMP_EN_SHIFT is 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'regulator/topic/tps6524x', 'regulator/topic/tps6586x', 'regulator/topic/tps65910', 'regulator/topic/tps80031', 'regulator/topic/wm831x', 'regulator/topic/wm8350' and 'regulator/topic/wm8994' into regulator-next
|
|
'regulator/topic/st-pwm', 'regulator/topic/ti-abb', 'regulator/topic/tps51632', 'regulator/topic/tps62360', 'regulator/topic/tps6507x', 'regulator/topic/tps65090' and 'regulator/topic/tps65217' into regulator-next
|
|
'regulator/topic/max8997', 'regulator/topic/max8998', 'regulator/topic/mc13xxx', 'regulator/topic/pfuze100', 'regulator/topic/rc5t583' and 'regulator/topic/s2mps11' into regulator-next
|
|
'regulator/topic/max77686', 'regulator/topic/max77693', 'regulator/topic/max8649', 'regulator/topic/max8660', 'regulator/topic/max8907', 'regulator/topic/max8925' and 'regulator/topic/max8952' into regulator-next
|
|
'regulator/topic/enable', 'regulator/topic/fan53555', 'regulator/topic/fixed', 'regulator/topic/gpio', 'regulator/topic/lp3971', 'regulator/topic/lp872x' and 'regulator/topic/max14577' into regulator-next
|
|
'regulator/topic/da9052', 'regulator/topic/da9055', 'regulator/topic/da9063', 'regulator/topic/da9210', 'regulator/topic/db8500' and 'regulator/topic/dbx500' into regulator-next
|
|
'regulator/topic/88pm8607', 'regulator/topic/aat2870', 'regulator/topic/act8865', 'regulator/topic/anatop', 'regulator/topic/arizona', 'regulator/topic/as3711' and 'regulator/topic/as3722' into regulator-next
|
|
|
|
The voltages in aat2870_ldo_voltages table are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Also remove test for selector in st_pwm_regulator_set_voltage_sel, the checking
is already done in .list_voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
On some STMicroelectronics hardware reside regulators consisting
partly of a PWM input connected to the feedback loop. As the PWM
duty-cycle is varied the output voltage adapts. This driver
allows us to vary the output voltage by adapting the PWM input
duty-cycle.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The **rdev of 'struct bcm590xx_reg' isn't used anywhere in the driver so
remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since commit ca5d1b3524b4d
"regulator: helpers: Modify helpers enabling multi-bit control",
we can set enable_val setting for device that use multiple bits for control.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This regulator is used for system IO and is fixed to 1.8V. Let's give
consumers the option to fetch the voltage level.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add of_node_put to decrement the ref count.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
of_find_node_by_name walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name instead.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
S2MPS14 regulators support suspend mode where their status is controlled
by PWREN coming from SoC. This patch implements the set_suspend_disable
for S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into regulator-s2mps11
|
|
Move the "};" to next line as is the general coding practice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
