| Age | Commit message (Collapse) | Author |
|---|
|
Some fault events like the over-current condition will get resolved
by the hardware, by e.g. disabling the port. As the status in the
interrupt status register is cleared on read when the fault is resolved,
the sysfs health property will only contain the correct health status
for the first time it is read after such an event, even if the actual
fault condition (like a VBUS short) still persists. To reflect this
properly in the property we cache the last health status and only update
the cache when a actual change happens, i.e. the ERR bit in the status
register flips, as this one properly reflects a continued fault condition.
The ALERT pin however, is not driven by the ERR status, but by the actual
fault status, so the pin will change back to it's default state when the
hardware has automatically resolved the fault by cutting the power. Thus
we never get an IRQ when the actual fault condition has been resolved and
the ERR status bit has been cleared in auto-recovery mode. To get this
information we need to poll the interrupt status register after some time
to see if the fault is gone and update our cache in that case.
To avoid any additional locking, we handle both paths (IRQ firing and
delayed polling) through the same single-threaded delayed work.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fix the following sparse warning:
drivers/power/supply/ucs1002_power.c:492:5: warning: symbol 'ucs1002_regulator_enable' was not declared. Should it be static?
Fixes: a3d70dacc727 ("power: suppy: ucs1002: disable power when max current is 0")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
For some devices userspace needs the ability to completely cut the power
to the USB devices connected to the charge controller. An easy way to
achieve this is by allowing 0 as a valid max current and forcibly disable
the output in that case, as well as enable it again if the regulator is
in use and a non-0 max current is set.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
drivers/power/supply/ucs1002_power.c:339:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Fixes: 9a2688e42638 ("power: supply: Add driver for Microchip UCS1002")
CC: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fix wrong return value checking for devm_regulator_register and
devm_regmap_init_i2c. This looks like a copy-n-paste mistake.
Fixes: 9a2688e42638 ("power: supply: Add driver for Microchip UCS1002")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add driver for Microchip UCS1002 Programmable USB Port Power
Controller with Charger Emulation. The driver exposed a power supply
device to control/monitor various parameter of the device as well as a
regulator to allow controlling VBUS line.
Signed-off-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
