Age | Commit message (Collapse) | Author |
|
This is needed to get access to UniPhier System Bus (external bus).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These pins do not support pin-muxing, but it is useful to support
pin configuration for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit updates the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding the new one. Having just one flag would be
better than adding a new struct member every time a new SoC-specific
capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from a customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Unfortunately, the pin number of the new SoC, PH1-LD11, is not
contiguous. The base frame work must be adjusted to support the new
SoC pinctrl driver. The pin_desc_get() exploits radix-tree for pin
look-up, so it works more efficiently with sparse pin space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Drive strength of some pins are controlled by
3-bit width registers (8-level granularity).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Some of the configuration registers on it have
3-bit width.
The feature will be supported in the next commit, but a problem is
that macro names are getting longer and longer in the current naming
scheme.
Before moving forward, this commit renames macros as follows:
UNIPHIER_PIN_DRV_4_8 -> UNIPHIER_PIN_DRV_1BIT
UNIPHIER_PIN_DRV_8_12_16_20 -> UNIPHIER_PIN_DRV_2BIT
UNIPHIER_PIN_DRV_FIXED_4 -> UNIPHIER_PIN_DRV_FIXED4
UNIPHIER_PIN_DRV_FIXED_5 -> UNIPHIER_PIN_DRV_FIXED5
UNIPHIER_PIN_DRV_FIXED_8 -> UNIPHIER_PIN_DRV_FIXED8
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently, every SoC driver defines struct pinctrl_desc statically,
i.e. it consumes memory footprint even if it is not probed.
In multi-platform, many pinctrl drivers are linked (generally as
built-in objects), although only one of them is actually used.
So, it is reasonable to allocate memory dynamically where possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Every SoC driver sets the same name for struct pinctrl_desc and
platform_driver. The common probe function can set desc->name
instead of duplicating strings in each SoC driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The owner of the struct pinctrl_desc matches that of platform_driver.
Set it in the common probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These pin tables were generated by parsing hardware documents with
a script, but the script had a bug. Fix the register offsets.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make function/variable names match the file names for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Without this, reading the "pins" in the debugfs causes kernel BUG.
Fixes: 6e9088920258 ("pinctrl: UniPhier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To i.MX7D, there are two iomux controllers, iomuxc and iomuxc_lpsr.
They should not share one pin controller descriptor, otherwise
the value filled into imx_pinctrl_desc when probing the first
iomux controller will be overridden when probing the second one.
In this patch, discard the static allcoated imx_pinctrl_desc and
switch to dynamically allcate pin controller descriptor for each
iomux controller.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domain pins for ethernet interface.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domain pins for UART A, B & C.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add EE domain pins for eMMC and SD card.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pins for some more AO domain devices: UART_AO_B and I2C master &
slave.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
-ENOMEM is more suitable error code because kasprintf() fails
in case of memory shortage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gc_pinctrl_remove() calls platform_get_drvdata(), but I see neither
platform_set_drvdata() nor dev_set_drvdata() anywhere in this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To improve debugfs readability, use commas instead of whitespaces
for separating configuration parameters.
For example, the "pinconf-pins" dump on my board will change as follows:
Without this commit:
# head -5 pinconf-pins
Pin config settings per pin
Format: pin (name): configs
pin 0 (ED0): input bias pull down output drive strength (8 mA) input enabled
pin 1 (ED1): input bias pull down output drive strength (8 mA) input enabled
pin 2 (ED2): input bias pull down output drive strength (8 mA) input enabled
With this commit:
# head -5 pinconf-pins
Pin config settings per pin
Format: pin (name): configs
pin 0 (ED0): input bias pull down, output drive strength (8 mA), input enabled
pin 1 (ED1): input bias pull down, output drive strength (8 mA), input enabled
pin 2 (ED2): input bias pull down, output drive strength (8 mA), input enabled
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently, struct pinctrl_pin_desc can have per-pin driver private
data, but it is not copied to struct pin_desc.
For a driver with sparse pin space, for-loop search like below would
be necessary in order to get the driver-specific data for a desired
pin number.
for (i = 0; i < pctldev->desc->npins; i++)
if (pin_number == pctldev->desc->pins[i].number)
return pctldev->desc->pins[i].drv_data;
This is not efficient for a driver with a large number of pins.
So, copy the data to struct pin_desc when each pin is registered
for the faster radix tree lookup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If a pin name is not specified in struct pinctrl_pin_desc,
pinctrl_register_one_pin() dynamically assigns its name.
So, desc->name is always a valid pointer here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Cc: stable@vger.kernel.org
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As these 2 functions code are 95% similar, factorize them.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The input/output directions were inversed on the GPIO direction
read function. Loose a ! and it is correct.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Although unbinding a pinctrl driver requires root privileges but it
still might be used theoretically in certain attacks (by triggering NULL
pointer exception or memory corruption).
Samsung pincontrol drivers are essential for system operation so their
removal is not expected. They do not implement remove() driver callback
and they are not buildable as modules.
Suppression of the unbinding will prevent triggering NULL pointer
exception like this (Odroid XU3):
$ echo 13400000.pinctrl > /sys/bus/platform/drivers/samsung-pinctrl/unbind
$ cat /sys/kernel/debug/gpio
Unable to handle kernel NULL pointer dereference at virtual address 00000c44
pgd = ec41c000
[00000c44] *pgd=6d448835, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
(samsung_gpio_get) from [<c034f9a0>] (gpiolib_seq_show+0x1b0/0x26c)
(gpiolib_seq_show) from [<c01fb8c0>] (seq_read+0x304/0x4b8)
(seq_read) from [<c02dbc78>] (full_proxy_read+0x4c/0x64)
(full_proxy_read) from [<c01d9fb0>] (__vfs_read+0x2c/0x110)
(__vfs_read) from [<c01db400>] (vfs_read+0x8c/0x110)
(vfs_read) from [<c01db4c4>] (SyS_read+0x40/0x8c)
(SyS_read) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Implement a get_direction callback for the OXNAS GPIO driver in order
to have pin output polarity in debugfs and new userspace ABI.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO pins
which also act as the special function in alternate mode. Also
there is configuration like push-pull, open drain, FPS timing
etc for these pins.
Add pin control driver to configure these parameters through
pin control APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove the use of parked_reg and use parked_bit for to know
whether field is supported or not.
This is fix for the patch
commit 1d18a3f0f0809f6c71f1f6e9e268ee904ce0b588
"pinctrl: tegra: avoid parked_reg and parked_bank
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit 0d5358330c20d50e52e3e65ff07a5db8007041fc.
|
|
Add pinctrl and gpio control support to Oxford Semiconductor OXNAS SoC Family.
This version supports the ARM926EJ-S based OX810SE SoC with 34 IO pins.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gcc-4.4 and thereabouts has issues with initializers of anonymous
unions, and it generates the following warnings:
drivers/pinctrl/intel/pinctrl-baytrail.c:413: error: unknown field 'simple_funcs' specified in initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: missing braces around initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: (near initialization for 'byt_score_groups[0].<anonymous>')
drivers/pinctrl/intel/pinctrl-baytrail.c:415: error: unknown field 'simple_funcs' specified in initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:417: error: unknown field 'simple_funcs' specified in initializer
...
Work around this.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (21 commits)
gitignore: fix wording
mfd: ab8500-debugfs: fix "between" in printk
memstick: trivial fix of spelling mistake on management
cpupowerutils: bench: fix "average"
treewide: Fix typos in printk
IB/mlx4: printk fix
pinctrl: sirf/atlas7: fix printk spelling
serial: mctrl_gpio: Grammar s/lines GPIOs/line GPIOs/, /sets/set/
w1: comment spelling s/minmum/minimum/
Blackfin: comment spelling s/divsor/divisor/
metag: Fix misspellings in comments.
ia64: Fix misspellings in comments.
hexagon: Fix misspellings in comments.
tools/perf: Fix misspellings in comments.
cris: Fix misspellings in comments.
c6x: Fix misspellings in comments.
blackfin: Fix misspelling of 'register' in comment.
avr32: Fix misspelling of 'definitions' in comment.
treewide: Fix typos in printk
Doc: treewide : Fix typos in DocBook/filesystem.xml
...
|
|
This reverts commit 1d18a3f0f0809f6c71f1f6e9e268ee904ce0b588.
|
|
Fix pinctrl eth_tx_en bit index according to Hardkernel ODROID-C1 datasheet.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currrently the gpio_chip.to_irq() callback returns -ENOSYS on error,
which causes bad interactions with the serial_mctrl_gpio helpers.
mctrl_gpio_init() returns -ENOSYS if GPIOLIB is not enabled, which is
intended to be ignored by its callers. However, ignoring -ENOSYS when it
was caused by a gpiod_to_irq() failure will lead to a crash later:
Unable to handle kernel paging request at virtual address ffffffde
...
PC is at mctrl_gpio_set+0x14/0x78
Fix this by returning zero instead, like gpiochip_to_irq() does.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
NVIDIA's Tegra210 support the park bit to make pinmux configuration
enable/disable. If parked bit is 1 then configuration does not apply
and if it is 0 then pinmux configuration applies. This is to support
to avoid any glitch in pinmux configurations.
The parked bit is part of mux register and mux bank and hence it is
not required to have member for the parked_reg and parked bank very
similar to other bit field of the same register.
Remove the need of the parked register and parked bank and get whether
parked function supported or not by parked_bit.
This is to make the parked bit handling same as other fields of mux
registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pincontrol registers of Tegra chips has multiple filed per
registers. There is two type of registers mux and drive. All
configurations belongs to one of these registers.
If any configurations are supported then <config>_bit is set to
bit position of these registers otherwise -1 to not support it.
The member is defined as
s32 <config>_bit:6;
So if config is not supported ifor given SoC then it is set to -1
in soc pinmmux table.
In common driver code, to find out that given config is supported
or not, it is checked as:
s8 bit = <config>_bit;
if (bit > 31) {
/* Not supported config */
}
But in this case, bit is s8 and hence for non supporting it is -1.
Correct the check as:
if (bit < 0) {
/* Not supported config */
}
Fixes: e4c02dced975cb ("pinctrl: tegra: use signed bitfields for optional fields")
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds the basic platform file to support the pin controller
found on the Amlogic Meson GXBB SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes the pinctrl pull bias setting, since the pull up/down
setting is the contrary for gpio0(just the gpio0a and gpio0b) and
gpio2(just the gpio2c and gpio2d).
From the TRM said, the gpio0a pull polarity setting:
gpio0a_p
GPIO0A PE/PS programmation section, every
GPIO bit corresponding to 2bits[PS:PE]
2'b00: Z(Normal operation);
2'b11: weak 1(pull-up);
2'b01: weak 0(pull-down);
2'b10: Z(Normal operation);
Then, the other gpios setting as the following:
gpio1a_p (e.g.: gpio1, gpio2a, gpio2b, gpio3...)
GPIO1A PU/PD programmation section, every
GPIO bit corresponding to 2bits
2'b00: Z(Normal operation);
2'b01: weak 1(pull-up);
2'b10: weak 0(pull-down);
2'b11: Z(Normal operation);
For example,(rk3399evb board)
sdmmc_cd --->gpio0_a7
localhost / # io -r -4 0xff320040
ff320040: 00004d5f
In general,the value should be 0x0000cd5f since the pin has been set
in the dts.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "phy: tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches adds support for the Tegra XUSB pad controller. The
controller provides a set of pads (lanes) that are used for I/O by other
IP blocks within Tegra SoCs (PCIe, SATA and XUSB).
* tag 'tegra-for-4.7-phy' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
|
|
nmk_gpio_get_mode is only used in one place, and that is conditionally
compiled if DEBUG_FS is enabled. A recent cleanup has marked the
definition 'static', which now leads to a warning:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:614:12: error: 'nmk_gpio_get_mode' defined but not used [-Werror=unused-function]
static int nmk_gpio_get_mode(struct nmk_gpio_chip *nmk_chip, int offset)
^~~~~~~~~~~~~~~~~
Moving the function itself inside the #ifdef shuts it up again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5e81e0a0913c ("pinctrl: nomadik: use BIT() with offsets consequently")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A conflict of two patches caused a build error when a function got renamed
but a new user appeared in the other patch:
drivers/pinctrl/bcm/pinctrl-ns2-mux.c:540:17: error: 'pinctrl_utils_dt_free_map' undeclared here (not in a function)
.dt_free_map = pinctrl_utils_dt_free_map,
^~~~~~~~~~~~~~~~~~~~~~~~~
This renames the new user of pinctrl_utils_dt_free_map accordingly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d32f7fd3bbc3 ("pinctrl: Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map")
Fixes: b5aa1006e4a9 ("pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This simplifies the normal as well as the error path.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|