Age | Commit message (Collapse) | Author | |
---|---|---|---|
2018-07-16 | pinctrl: at91-pio4: Remove redundant return value check | Wei Yongjun | |
Remove unneeded error handling on the result of a call to platform_get_resource() when the value is passed to devm_ioremap_resource(). Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2018-07-16 | pinctrl: at91-pio4: add support for drive strength | Ludovic Desroches | |
Add support for the drive strength configuration. Usually, this value is expressed in mA. Since the numeric value depends on VDDIOP voltage, a value we can't retrieve at runtime, the controller uses low, medium and high to define the drive strength. The PIO controller accepts two values for the low drive configuration: 0 and 1. Most of the time, we don't care about the drive strength. So we keep the default value which is 0. The drive strength is advertised through the sysfs only when it has been explicitly set in the device tree i.e. if its value is different from 0. Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2018-06-12 | treewide: devm_kzalloc() -> devm_kcalloc() | Kees Cook | |
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org> | |||
2018-05-24 | pinctrl: at91-pio4: add missing of_node_put | Julia Lawall | |
The device node iterators perform an of_node_get on each iteration, so a jump out of the loop requires an of_node_put. The semantic patch that fixes this problem is as follows (http://coccinelle.lip6.fr): // <smpl> @@ expression root,e; local idexpression child; iterator name for_each_child_of_node; @@ for_each_child_of_node(root, child) { ... when != of_node_put(child) when != e = child + of_node_put(child); ? break; ... } ... when != child // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2018-01-08 | pinctrl: at91-pio4: account for const type of of_device_id.data | Julia Lawall | |
This driver creates a const structure that it stores in the data field of an of_device_id array. Adding const to the declaration of the location that receives the const value from the data field ensures that the compiler will continue to check that the value is not modified. Furthermore, the const-discarding cast on the extraction from the data field is no longer needed. Done using Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2017-08-14 | pinctrl: Convert to using %pOF instead of full_name | Rob Herring | |
Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Lee Jones <lee@kernel.org> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Tomasz Figa <tomasz.figa@gmail.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Barry Song <baohua@kernel.org> Cc: linux-gpio@vger.kernel.org Cc: linux-rpi-kernel@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: kernel@stlinux.com Cc: linux-samsung-soc@vger.kernel.org Cc: linux-renesas-soc@vger.kernel.org Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2017-04-07 | pinctrl: at91-pio4: handle suspend to ram | Alexandre Belloni | |
When suspending to RAM, the power to the core is cut and the register values are lost. Save and restore more registers than just IMR. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2016-06-13 | pinctrl: at91-pio4: make it explicitly non-modular | Paul Gortmaker | |
The Kconfig currently controlling compilation of this code is: drivers/pinctrl/Kconfig:config PINCTRL_AT91PIO4 drivers/pinctrl/Kconfig: bool "AT91 PIO4 pinctrl driver" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. We explicitly disallow a driver unbind, since that doesn't have a sensible use case anyway, and it allows us to drop the ".remove" code for non-modular drivers. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2016-06-08 | pinctrl: at91-pio4: fix non-exported functions | Ben Dooks | |
The atmel_pctl_find_group_by_pin() and the atmel_pinctrl_remove() functions are not exported, so fix the warnings about these being exported without definitions by making them static. drivers/pinctrl/pinctrl-at91-pio4.c:424:20: warning: symbol 'atmel_pctl_find_group_by_pin' was not declared. Should it be static? drivers/pinctrl/pinctrl-at91-pio4.c:1077:5: warning: symbol 'atmel_pinctrl_remove' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2016-05-19 | Merge tag 'pinctrl-v4.7-1' of ↵ | Linus Torvalds | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This kernel cycle was quite calm when it comes to pin control and there is really just one major change, and that is the introduction of devm_pinctrl_register() managed resources. Apart from that linear development, details below. Core changes: - Add the devm_pinctrl_register() API and switch all applicable drivers to use it, saving lots of lines of code all over the place. New drivers: - driver for the Broadcom NS2 SoC - subdriver for the PXA25x SoCs - subdriver for the AMLogic Meson GXBB SoC Driver improvements: - the Intel Baytrail driver now properly supports pin control - Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction() callback in the GPIO portions - continued development and stabilization of several SH-PFC SoC subdrivers: r8a7795, r8a7790, r8a7794 etc" * tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits) Revert "pinctrl: tegra: avoid parked_reg and parked_bank" pinctrl: meson: Fix eth_tx_en bit index pinctrl: tegra: avoid parked_reg and parked_bank pinctrl: tegra: Correctly check the supported configuration pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC pinctrl: rockchip: fix pull setting error for rk3399 pinctrl: stm32: Implement .pin_config_dbg_show() pinctrl: nomadik: hide nmk_gpio_get_mode when unused pinctrl: ns2: rename pinctrl_utils_dt_free_map pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable pinctrl: at91: Make at91_gpio_template const pinctrl: baytrail: fix some error handling in debugfs pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove() pinctrl: nomadik: implement .get_direction() pinctrl: nomadik: use BIT() with offsets consequently pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration ... | |||
2016-04-29 | pinctrl: at91-pio4: fix pull-up/down logic | Ludovic Desroches | |
The default configuration of a pin is often with a value in the pull-up/down field at chip reset. So, even if the internal logic of the controller prevents writing a configuration with pull-up and pull-down at the same time, we must ensure explicitly this condition before writing the register. This was leading to a pull-down condition not taken into account for instance. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: 776180848b57 ("pinctrl: introduce driver for Atmel PIO4 controller") Cc: stable@vger.kernel.org #v4.4 and later Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2016-04-21 | pinctrl: at91-pio4: Use devm_pinctrl_register() for pinctrl registration | Laxman Dewangan | |
Use devm_pinctrl_register() for pin control registration and clean error path. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2016-04-01 | pinctrl: Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map | Irina Tirdea | |
Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, since it does not depend on device tree despite the current name. This will enforce a consistent naming in pinctr-utils.c and will make it clear it can be called from outside device tree (e.g. from ACPI handling code). Signed-off-by: Irina Tirdea <irina.tirdea@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2016-03-09 | pinctrl: at91: use __maybe_unused to hide pm functions | Arnd Bergmann | |
The at91-pio4 pinctrl driver uses SET_SYSTEM_SLEEP_PM_OPS() to conditionally set the correct suspend/resume options, but they become unused when CONFIG_PM is disabled: drivers/pinctrl/pinctrl-at91-pio4.c:827:12: error: 'atmel_pctrl_suspend' defined but not used [-Werror=unused-function] drivers/pinctrl/pinctrl-at91-pio4.c:847:12: error: 'atmel_pctrl_resume' defined but not used [-Werror=unused-function] This adds __maybe_unused annotations so the compiler knows it can silently drop them instead of warning. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2016-01-17 | Merge tag 'gpio-v4.5-1' of ↵ | Linus Torvalds | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "Here is the bulk of GPIO changes for v4.5. Notably there are big refactorings mostly by myself, aimed at getting the gpio_chip into a shape that makes me believe I can proceed to preserve state for a proper userspace ABI (character device) that has already been proposed once, but resulted in the feedback that I need to go back and restructure stuff. So I've been restructuring stuff. On the way I ran into brokenness (return code from the get_value() callback) and had to fix it. Also, refactored generic GPIO to be simpler. Some of that is still waiting to trickle down from the subsystems all over the kernel that provide random gpio_chips, I've touched every single GPIO driver in the kernel now, oh man I didn't know I was responsible for so much... Apart from that we're churning along as usual. I took some effort to test and retest so it should merge nicely and we shook out a couple of bugs in -next. Infrastructural changes: - In struct gpio_chip, rename the .dev node to .parent to better reflect the fact that this is not the GPIO struct device abstraction. We will add that soon so this would be totallt confusing. - It was noted that the driver .get_value() callbacks was sometimes reporting negative -ERR values to the gpiolib core, expecting them to be propagated to consumer gpiod_get_value() and gpio_get_value() calls. This was not happening, so as there was a mess of drivers returning negative errors and some returning "anything else than zero" to indicate that a line was active. As some would have bit 31 set to indicate "line active" it clashed with negative error codes. This is fixed by the largeish series clamping values in all drivers with !!value to [0,1] and then augmenting the code to propagate error codes to consumers. (Includes some ACKed patches in other subsystems.) - Add a void *data pointer to struct gpio_chip. The container_of() design pattern is indeed very nice, but we want to reform the struct gpio_chip to be a non-volative, stateless business, and keep states internal to the gpiolib to be able to hold on to the state when adding a proper userspace ABI (character device) further down the road. To achieve this, drivers need a handle at the internal state that is not dependent on their struct gpio_chip() so we add gpiochip_add_data() and gpiochip_get_data() following the pattern of many other subsystems. All the "use gpiochip data pointer" patches transforms drivers to this scheme. - The Generic GPIO chip header has been merged into the general <linux/gpio/driver.h> header, and the custom header for that removed. Instead of having a separate mm_gpio_chip struct for these generic drivers, merge that into struct gpio_chip, simplifying the code and removing the need for separate and confusing includes. Misc improvements: - Stabilize the way GPIOs are looked up from the ACPI legacy specification. - Incremental driver features for PXA, PCA953X, Lantiq (patches from the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48 New drivers: - Add a GPIO chip to the ALSA SoC AC97 driver. - Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but the branch is merged here too to account for infrastructural changes). - The sx150x driver now supports the sx1502" * tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits) gpio: generic: make bgpio_pdata always visible gpiolib: fix chip order in gpio list gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs() gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs() gpio: brcmstb: Allow building driver for BMIPS_GENERIC gpio: brcmstb: Set endian flags for big-endian MIPS gpio: moxart: fix build regression gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs() leds: pca9532: use gpiochip data pointer leds: tca6507: use gpiochip data pointer hid: cp2112: use gpiochip data pointer bcma: gpio: use gpiochip data pointer avr32: gpio: use gpiochip data pointer video: fbdev: via: use gpiochip data pointer gpio: pch: Optimize pch_gpio_get() Revert "pinctrl: lantiq: Implement gpio_chip.to_irq" pinctrl: nsp-gpio: use gpiochip data pointer pinctrl: vt8500-wmt: use gpiochip data pointer pinctrl: exynos5440: use gpiochip data pointer pinctrl: at91-pio4: use gpiochip data pointer ... | |||
2016-01-05 | pinctrl: at91-pio4: use gpiochip data pointer | Linus Walleij | |
This makes the driver use the data pointer added to the gpio_chip to store a pointer to the state container instead of relying on container_of(). Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2015-12-10 | pinctrl: at91-pio4: fix memleak after using dt map | Ludovic Desroches | |
configs is allocated by pinconf_generic_parse_dt_config(), pinctrl_utils_add_map_configs() duplicates configs so it can and has to be freed to prevent memory leaks. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Reported-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2015-11-30 | pinctrl: at91-pio4: use %pr format string for resource | Arnd Bergmann | |
resource_size_t may be defined as 32 or 64 bit depending on configuration, so it cannot be printed using the normal format strings, as gcc correctly warns: pinctrl-at91-pio4.c: In function 'atmel_pinctrl_probe': pinctrl-at91-pio4.c:1003:41: warning: format '%u' expects argument of type 'unsigned int', but argument 5 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=] dev_dbg(dev, "bank %i: hwirq=%u\n", i, res->start); This changes the format string to use the special "%pr" format string that prints a resource, and changes the arguments so we the resource structure directly. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2015-11-19 | gpio: change member .dev to .parent | Linus Walleij | |
The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2015-10-02 | pinctrl: at91-pio4: irq argument as been removed from irq flow handlers | Ludovic Desroches | |
Irq argument as been removed from irq flow handlers so use the irq descriptor to retrieve data we need. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2015-10-02 | pinctrl: at91-pio4: use irq_set_handler_locked | Ludovic Desroches | |
Use irq_set_handler_locked() as it avoids a redundant lookup of the irq descriptor. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2015-10-02 | pinctrl: at91-pio4: add PM stuff | Ludovic Desroches | |
Allow GPIOs to be configured as wakeup sources. When going to suspend, disable all GPIO irqs excepting the one configured as wakeup sources. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> | |||
2015-09-21 | pinctrl: introduce driver for Atmel PIO4 controller | Ludovic Desroches | |
Add a pinctrl/gpio driver for Atmel PIO4 controller available on SAMA5D2 chip family. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |