Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- more printk modernization
- various cleanups and fixes (incl. a race condition) for Mac
- defconfig updates
* tag 'm68k-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.14-rc7
m68k/mac: Add mutual exclusion for IOP interrupt polling
m68k/mac: Disentangle VIA/RBV and NuBus initialization
m68k/mac: Disentangle VIA and OSS initialization
m68k/mac: More printk modernization
|
|
The Nubus subsystem should not be concerned with differences between VIA,
RBV and OSS platforms. It should be portable across Macs and PowerMacs.
This goal has implications for the initialization code relating to bus
locking and slot interrupts.
During Nubus initialization, bus transactions are "unlocked": on VIA2 and
RBV machines, via_nubus_init() sets a bit in the via2[gBufB] register to
allow bus-mastering Nubus cards to arbitrate for the bus. This happens
upon subsys_initcall(nubus_init). But because nubus_init() has no effect
on card state, this sequence is arbitrary.
Moreover, when Penguin is used to boot Linux, the bus is already unlocked
when Linux starts. On OSS machines there's no attempt to unlock Nubus
transactions at all. (Maybe there's no benefit on that platform or maybe
no-one knows how.)
All of this demonstrates that there's no benefit in locking out
bus-mastering cards, as yet. (If the need arises, we could lock the bus
for the duration of a timing-critical operation.) NetBSD unlocks the
Nubus early (at VIA initialization) and we can do the same.
via_nubus_init() is also responsible for some VIA interrupt setup that
should happen earlier than subsys_initcall(nubus_init). And actually, the
Nubus subsystem need not be involved with slot interrupts: SLOT2IRQ
works fine because Nubus slot IRQs are geog/*
* GPIO driver for the TS-4800 board
*
* Copyright (c) 2016 - Savoir-faire Linux
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/gpio/driver.h>
#include <linux/of_address.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#define DEFAULT_PIN_NUMBER 16
#define INPUT_REG_OFFSET 0x00
#define OUTPUT_REG_OFFSET 0x02
#define DIRECTION_REG_OFFSET 0x04
static int ts4800_gpio_probe(struct platform_device *pdev)
{
struct device_node *node;
struct gpio_chip *chip;
struct resource *res;
void __iomem *base_addr;
int retval;
u32 ngpios;
chip = devm_kzalloc(&pdev->dev, sizeof(struct gpio_chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base_addr = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(base_addr))
return PTR_ERR(base_addr);
node = pdev->dev.of_node;
if (!node)
return -EINVAL;
retval = of_property_read_u32(node, "ngpios", &ngpios);
if (retval == -EINVAL)
ngpios = DEFAULT_PIN_NUMBER;
else if (retval)
return retval;
retval = bgpio_init(chip, &pdev->dev, 2, base_addr + INPUT_REG_OFFSET,
base_addr + OUTPUT_REG_OFFSET, NULL,
base_addr + DIRECTION_REG_OFFSET, NULL, 0);
if (retval) {
dev_err(&pdev->dev, "bgpio_init failed\n");
2014-10-27 | nubus: Remove superfluous interrupt disable/restore | Geert Uytterhoeven | |
|
As of commit e4dc601bf99ccd1c ("m68k: Disable/restore interrupts in
hwreg_present()/hwreg_write()"), this is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
... instead of naked numbers.
Stuff in sysrq.c used to set it to 8 which is supposed to mean above
default level so set it to DEBUG instead as we're terminating/killing all
tasks and we want to be verbose there.
Also, correct the check in x86_64_start_kernel which should be >= as
we're clearly issuing the string there for all debug levels, not only
the magical 10.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Joe Perches <joe@perches.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 59d8053f1e16904d54ed7469d4b36801ea6b8f2c ("proc: Move non-public
stuff from linux/proc_fs.h to fs/proc/internal.h") broke Apple NuBus
support:
drivers/nubus/proc.c: In function ‘nubus_proc_detach_device’:
drivers/nubus/proc.c:156: error: dereferencing pointer to incomplete type
drivers/nubus/proc.c:158: error: dereferencing pointer to incomplete type
Fortunately nubus_proc_detach_device() is unused, and appears to have never
been used, so just remove it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Don't use create_proc_entry() in nubus_proc_subdir(). The files created aren't
given any way to use them, so for the moment use create_proc_read_entry() with
a NULL accessor and generate a compile-time warning.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
It seems this is the right way around because otherwise the len usage in
the outer loop would be pretty pointless.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove proc_bus export and variable itself. Using pathnames works fine
and is slightly more understandable and greppable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
nubus: kill drivers/nubus/nubus_syms.c
EXPORT_SYMBOL's belong to the actual code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|