Age | Commit message (Collapse) | Author |
|
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f32593773549 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
list_for_each_entry_from_reverse() iterates backwards over the list from
the current position, but in the error path we should start from the
previous position.
Fix this by using list_for_each_entry_continue_reverse() instead.
This suppresses the following error from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//spectrum_mr.c:655:34-38: ERROR:
invalid reference to the index variable of the iterator on line 636
Fixes: c011ec1bbfd6 ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In qlcnic_83xx_get_reset_instruction_template, the variable
of null test is bad, so correct it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
Fourth, and last, set of fixes for v5.6. Just two important fixes to
iwlwifi regressions.
iwlwifi
* fix GEO_TX_POWER_LIMIT command on certain devices which caused
firmware to crash during initialisation
* add back device ids for three devices which were accidentally
removed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1afd99484 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ENA only provides the PCI remove() handler, used during rmmod
for example. This is not called on shutdown/kexec path; we are potentially
creating a failure scenario on kexec:
(a) Kexec is triggered, no shutdown() / remove() handler is called for ENA;
instead pci_device_shutdown() clears the master bit of the PCI device,
stopping all DMA transactions;
(b) Kexec reboot happens and the device gets enabled again, likely having
its FW with that DMA transaction buffered; then it may trigger the (now
invalid) memory operation in the new kernel, corrupting kernel memory area.
This patch aims to prevent this, by implementing a shutdown() handler
quite similar to the remove() one - the difference being the handling
of the netdev, which is unregistered on remove(), but following the
convention observed in other drivers, it's only detached on shutdown().
This prevents an odd issue in AWS Nitro instances, in which after the 2nd
kexec the next one will fail with an initrd corruption, caused by a wild
DMA write to invalid kernel memory. The lspci output for the adapter
present in my instance is:
00:05.0 Ethernet controller [0200]: Amazon.com, Inc. Elastic Network
Adapter (ENA) [1d0f:ec20]
Suggested-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-24
This series introduces some fixes to mlx5 driver.
From Aya, Fixes to the RX error recovery flows
From Leon, Fix IB capability mask
Please pull and let me know if there is any problem.
For -stable v5.5
('net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure')
For -stable v5.4
('net/mlx5e: Fix ICOSQ recovery flow with Striding RQ')
('net/mlx5e: Do not recover from a non-fatal syndrome')
('net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset')
('net/mlx5e: Enhance ICOSQ WQE info fields')
The above patch ('net/mlx5e: Enhance ICOSQ WQE info fields')
will fail to apply cleanly on v5.4 due to a trivial contextual conflict,
but it is an important fix, do I need to do something about it or just
assume Greg will know how to handle this ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7b4 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DT binding for this PHY describes an *optional* clock property.
Due to a bug in the error handling logic, we are actually ignoring this
clock *all* of the time so far.
Fix this by using devm_clk_get_optional() to handle this clock properly.
Fixes: b78ac6ecd1b6b ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb4_ptp_fineadjtime() doesn't pass the signedness of offset delta
in FW_PTP_CMD. Fix it by passing correct sign.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For non-fatal syndromes like LOCAL_LENGTH_ERR, recovery shouldn't be
triggered. In these scenarios, the RQ is not actually in ERR state.
This misleads the recovery flow which assumes that the RQ is really in
error state and no more completions arrive, causing crashes on bad page
state.
Fixes: 8276ea1353a4 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.
In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:
- The buffers of the in-progress WQEs must be released
and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.
For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().
Fixes: be5323c8379f ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.
Fixes: 8276ea1353a4 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.
In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.
Fixes: be5323c8379f ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The cap_mask1 isn't protected by field_select and not listed among RW
fields, but it is required to be written to properly initialize ports
in IB virtualization mode.
Link: https://lore.kernel.org/linux-rdma/88bab94d2fd72f3145835b4518bc63dda587add6.camel@redhat.com
Fixes: ab118da4c10a ("net/mlx5: Don't write read-only fields in MODIFY_HCA_VPORT_CONTEXT command")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56a7 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd7b ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2ad ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe855 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed790335 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only attach macsec to ethernet devices.
Syzbot was able to trigger a KMSAN warning in macsec_handle_frame
by attaching to a phonet device.
Macvlan has a similar check in macvlan_port_create.
v1->v2
- fix commit message typo
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ASKEY WWHC050 is a mcie LTE modem.
The oem configuration states:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1690 ProdID=7588 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=813f0eef6e6e
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Tested on openwrt distribution.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-05
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v5.4
('net/mlx5: DR, Fix postsend actions write length')
For -stable v5.5
('net/mlx5e: kTLS, Fix TCP seq off-by-1 issue in TX resync flow')
('net/mlx5e: Fix endianness handling in pedit mask')
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GEO_TX_POWER_LIMIT command was sent although
there is no wgds table, so the fw got wrong SAR values
from the driver.
Fix this by avoiding sending the command if no wgds
tables are available.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Fixes: 39c1a9728f93 ("iwlwifi: refactor the SAR tables from mvm to acpi")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested-By: Jonathan McDowell <noodles@earth.li>
Tested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200318081237.46db40617cc6.Id5cf852ec8c5dbf20ba86bad7b165a0c828f8b2e@changeid
|
|
Three devices, with PCI device ID 0x2526 and subdevice IDs 0x4010,
0x4018 and 0x401C were removed accidentally. Add them back.
Reported-by: Brett Hassal <brett.hassal@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206661
Fixes: 0b295a1eb81f ("iwlwifi: add device name to device_info")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200317123331.16762b29f26c.I928bcaa799e7b3d33838c0667714eeb9fa665290@changeid
|
|
The hardware offloading of the NETIF_F_HW_CSUM and NETIF_F_RXCSUM
features requires the use of Transmit Status Blocks before transmit
frame data and Receive Status Blocks before receive frame data to
carry the checksum information.
Unfortunately, these status blocks are currently only enabled when
the NETIF_F_HW_CSUM feature is enabled. As a result NETIF_F_RXCSUM
will not actually be offloaded to the hardware unless both it and
NETIF_F_HW_CSUM are enabled. Fortunately, that is the default
configuration.
This commit addresses this issue by always enabling the use of
status blocks on both transmit and receive frames. Further, it
replaces the use of a dedicated flag within the driver private
data structure with direct use of the netdev features flags.
Fixes: 810155397890 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the DP83867 PHY is strapped to enable Fast Link Drop (FLD) feature
STRAP_STS2.STRAP_ FLD (reg 0x006F bit 10), the Energy Lost Threshold for
FLD Energy Lost Mode FLD_THR_CFG.ENERGY_LOST_FLD_THR (reg 0x002e bits 2:0)
will be defaulted to 0x2. This may cause the phy link to be unstable. The
new DP83867 DM recommends to always restore ENERGY_LOST_FLD_THR to 0x1.
Hence, restore default value of FLD_THR_CFG.ENERGY_LOST_FLD_THR to 0x1 when
FLD is enabled by bootstrapping as recommended by DM.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we clean up devicetree related configuration
also when clock init fails.
Fixes: fecd4d7eef8b ("net: stmmac: dwmac-rk: Add integrated PHY support")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
This patch is a 1:1 copy of upstream slip.c commit f596c87005f7
("slip: not call free_netdev before rtnl_unlock in slip_open").
Reported-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Headers ionic_if.h and ionic_regs.h are licensed under three alternative
licenses and the used SPDX-License-Identifier expression makes
./scripts/spdxcheck.py complain:
drivers/net/ethernet/pensando/ionic/ionic_if.h: 1:52 Syntax error: OR
drivers/net/ethernet/pensando/ionic/ionic_regs.h: 1:52 Syntax error: OR
As OR is associative, it is irrelevant if the parentheses are put around
the first or the second OR-expression.
Simply add parentheses to make spdxcheck.py happy.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the minimum value of skb len that hw supports is 32 rather than 17
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the second input parameter of wait_for_completion_timeout should
be jiffies instead of millisecond
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add read barrier in driver code to keep from reading other fileds
in dma memory which is writable for hw until we have verified the
memory is valid for driver
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
should disable eq irq before freeing it, must clear event queue
depth in hw before freeing relevant memory to avoid illegal
memory access and update consumer idx to avoid invalid interrupt
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
it's unreliable for fw to check whether IO is stopped, so driver
wait for enough time to ensure IO process is done in hw before
freeing resources
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver reclaims descriptors in much smaller batches, even if hardware
indicates more to reclaim, during backpressure. So, fix the check to
restart the Txq during backpressure, by looking at how many
descriptors hardware had indicated to reclaim, and not on how many
descriptors that driver had actually reclaimed. Once the Txq is
restarted, driver will reclaim even more descriptors when Tx path
is entered again.
Fixes: d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 7c3bebc3d868 ("cxgb4: request the TX CIDX updates to status page")
reverted back to getting Tx CIDX updates via DMA, instead of interrupts,
introduced by commit d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE
doorbell queue timer")
However, it missed reverting back several code changes where Tx CIDX
updates are not explicitly requested during backpressure when using
interrupt mode. These missed changes cause slow recovery during
backpressure because the corresponding interrupt no longer comes and
hence results in Tx throughput drop.
So, revert back these missed code changes, as well, which will allow
explicitly requesting Tx CIDX updates when backpressure happens.
This enables the corresponding interrupt with Tx CIDX update message
to get generated and hence speed up recovery and restore back
throughput.
Fixes: 7c3bebc3d868 ("cxgb4: request the TX CIDX updates to status page")
Fixes: d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew reported:
After a number of network port link up/down changes, sometimes the switch
port gets stuck in a state where it thinks it is still transmitting packets
but the cpu port is not actually transmitting anymore. In this state you
will see a message on the console
"mtk_soc_eth 1e100000.ethernet eth0: transmit timed out" and the Tx counter
in ifconfig will be incrementing on virtual port, but not incrementing on
cpu port.
The issue is that MAC TX/RX status has no impact on the link status or
queue manager of the switch. So the queue manager just queues up packets
of a disabled port and sends out pause frames when the queue is full.
Change the LINK bit to reflect the link status.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reported-by: Andrew Smith <andrew.smith@digi.com>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During initialization the driver issues a software reset command and
then waits for the system status to change back to "ready" state.
However, before issuing the reset command the driver does not check that
the system is actually in "ready" state. On Spectrum-{1,2} systems this
was always the case as the hardware initialization time is very short.
On Spectrum-3 systems this is no longer the case. This results in the
software reset command timing-out and the driver failing to load:
[ 6.347591] mlxsw_spectrum3 0000:06:00.0: Cmd exec timed-out (opcode=40(ACCESS_REG),opcode_mod=0,in_mod=0)
[ 6.358382] mlxsw_spectrum3 0000:06:00.0: Reg cmd access failed (reg_id=9023(mrsr),type=write)
[ 6.368028] mlxsw_spectrum3 0000:06:00.0: cannot register bus device
[ 6.375274] mlxsw_spectrum3: probe of 0000:06:00.0 failed with error -110
Fix this by waiting for the system to become ready both before issuing
the reset command and afterwards. In case of failure, print the last
system status to aid in debugging.
Fixes: da382875c616 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We precompute the static-static ECDH during configuration time, in order
to save an expensive computation later when receiving network packets.
However, not all ECDH computations yield a contributory result. Prior,
we were just not letting those peers be added to the interface. However,
this creates a strange inconsistency, since it was still possible to add
other weird points, like a valid public key plus a low-order point, and,
like points that result in zeros, a handshake would not complete. In
order to make the behavior more uniform and less surprising, simply
allow all peers to be added. Then, we'll error out later when doing the
crypto if there's an issue. This also adds more separation between the
crypto layer and the configuration layer.
Discussed-with: Mathias Hall-Andersen <mathias@hall-andersen.dk>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The situation in which we wind up hitting the default case here
indicates a major bug in earlier parsing code. It is not a usual thing
that should ever happen, which means a "friendly" message for it doesn't
make sense. Rather, replace this with a WARN_ON, just like we do earlier
in the file for a similar situation, so that somebody sends us a bug
report and we can fix it.
Reported-by: Fabian Freyer <fabianfreyer@radicallyopensecurity.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We carry out checks to the effect of:
if (skb->protocol != wg_examine_packet_protocol(skb))
goto err;
By having wg_skb_examine_untrusted_ip_hdr return 0 on failure, this
means that the check above still passes in the case where skb->protocol
is zero, which is possible to hit with AF_PACKET:
struct sockaddr_pkt saddr = { .spkt_device = "wg0" };
unsigned char buffer[5] = { 0 };
sendto(socket(AF_PACKET, SOCK_PACKET, /* skb->protocol = */ 0),
buffer, sizeof(buffer), 0, (const struct sockaddr *)&saddr, sizeof(saddr));
Additional checks mean that this isn't actually a problem in the code
base, but I could imagine it becoming a problem later if the function is
used more liberally.
I would prefer to fix this by having wg_examine_packet_protocol return a
32-bit ~0 value on failure, which will never match any value of
skb->protocol, which would simply change the generated code from a mov
to a movzx. However, sparse complains, and adding __force casts doesn't
seem like a good idea, so instead we just add a simple helper function
to check for the zero return value. Since wg_examine_packet_protocol
itself gets inlined, this winds up not adding an additional branch to
the generated code, since the 0 return value already happens in a
mergable branch.
Reported-by: Fabian Freyer <fabianfreyer@radicallyopensecurity.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gro_cells_init() returns error if memory allocation is failed.
But the vxlan module doesn't check the return value of gro_cells_init().
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer")`
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The indentation for the returned values are weird, causing those
warnings:
./drivers/net/phy/sfp-bus.c:579: WARNING: Unexpected indentation.
./drivers/net/phy/sfp-bus.c:619: WARNING: Unexpected indentation.
Use a list and change the identation for it to be properly
parsed by the documentation toolchain.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
last_keep_alive_jiffies is updated in probe and when a keep-alive
event is received. In case the driver times-out on a keep-alive event,
it has high chances of continuously timing-out on keep-alive events.
This is because when the driver recovers from the keep-alive-timeout reset
the value of last_keep_alive_jiffies is very old, and if a keep-alive
event is not received before the next timer expires, the value of
last_keep_alive_jiffies will cause another keep-alive-timeout reset
and so forth in a loop.
Solution:
Update last_keep_alive_jiffies whenever the device is restored after
reset.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx req_id is an index in struct ena_eth_io_rx_cdesc_base.
The driver should validate that the Rx req_id it received from
the device is in range [0, ring_size -1]. Failure to do so could
yield to potential memory access violoation.
The validation was mistakenly done when refilling
the Rx submission queue and not in Rx completion queue.
Fixes: ad974baef2a1 ("net: ena: add support for out of order rx buffers refill")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug:
In short the main issue is caused by the fact that the number of queues
is changed using ethtool after ena_probe() has been called and before
ena_up() was executed. Here is the full scenario in detail:
* ena_probe() is called when the driver is loaded, the driver is not up
yet at the end of ena_probe().
* The number of queues is changed -> io_queue_count is changed as well -
ena_up() is not called since the "dev_was_up" boolean in
ena_update_queue_count() is false.
* ena_up() is called by the kernel (it's called asynchronously some
time after ena_probe()). ena_setup_io_intr() is called by ena_up() and
it uses io_queue_count to get the suitable irq lines for each msix
vector. The function ena_request_io_irq() is called right after that
and it uses msix_vecs - This value only changes during ena_probe() and
ena_restore() - to request the irq vectors. This results in "Failed to
request I/O IRQ" error for i > io_queue_count.
Numeric example:
* After ena_probe() io_queue_count = 8, msix_vecs = 9.
* The number of queues changes to 4 -> io_queue_count = 4, msix_vecs = 9.
* ena_up() is executed for the first time:
** ena_setup_io_intr() inits the vectors only up to io_queue_count.
** ena_request_io_irq() calls request_irq() and fails for i = 5.
How to reproduce:
simply run the following commands:
sudo rmmod ena && sudo insmod ena.ko;
sudo ethtool -L eth1 combined 3;
Fix:
Use ENA_MAX_MSIX_VEC(adapter->num_io_queues + adapter->xdp_num_queues)
instead of adapter->msix_vecs. We need to take XDP queues into
consideration as they need to have msix vectors assigned to them as well.
Note that the XDP cannot be attached before the driver is up and running
but in XDP mode the issue might occur when the number of queues changes
right after a reset trigger.
The ENA_MAX_MSIX_VEC simply adds one to the argument since the first msix
vector is reserved for management queue.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overview:
We don't frequently change the msix vectors throughout the life cycle of
the driver. We do so in two functions: ena_probe() and ena_restore().
ena_probe() is only called when the driver is loaded. ena_restore() on the
other hand is called during device reset / resume operations.
We use num_io_queues for calculating and allocating the number of msix
vectors. At ena_probe() this value is equal to max_num_io_queues and thus
this is not an issue, however ena_restore() might be called after the
number of io queues has changed.
A possible bug scenario is as follows:
* Change number of queues from 8 to 4.
(num_io_queues = 4, max_num_io_queues = 8, msix_vecs = 9,)
* Trigger reset occurs -> ena_restore is called.
(num_io_queues = 4, max_num_io_queues =8 , msix_vecs = 5)
* Change number of queues from 4 to 6.
(num_io_queues = 6, max_num_io_queues = 8, msix_vecs = 5)
* The driver will reset due to failure of check_for_rx_interrupt_queue()
Fix:
This can be easily fixed by always using max_num_io_queues to init the
msix_vecs, since this number won't change as opposed to num_io_queues.
Fixes: 4d19266022ec ("net: ena: multiple queue creation related cleanups")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check clk_prepare_enable() return value.
Fixes: 2c7230446bc9 ("net: phy: Add pm support to Broadcom iProc mdio mux driver")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|