| Age | Commit message (Collapse) | Author |
|---|
|
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272df6 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
hard_header_len provides limitations for things like AF_PACKET, such
that we don't allow transmitting packets smaller than this.
needed_headroom provides a suggested minimum headroom for SKBs, so that
we can trivally add our headers to the front.
The latter is the correct field to use in this case, while the former
mostly just prevents sending small AF_PACKET frames.
In any case, mwifiex already does its own bounce buffering [1] if we
don't have enough headroom, so hints (not hard limits) are all that are
needed.
This is the essentially the same bug (and fix) that brcmfmac had, fixed
in commit cb39288fd6bb ("brcmfmac: use ndev->needed_headroom to reserve
additional header space").
[1] mwifiex_hard_start_xmit():
if (skb_headroom(skb) < MWIFIEX_MIN_DATA_HEADER_LEN) {
[...]
/* Insufficient skb headroom - allocate a new skb */
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.gbhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove unneeded variable ret used to store return value.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The simple_strtol() function is deprecated since it does not
check for the range overflow. Use kstrtoint() instead.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove unused fab_version member from struct rtw_hal.
Some of the checks being made were nonsense.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Firmware supports only STA as primary interface in repeater mode.
Since the only meaningful usage of AP + STA interface combination
is repeater, reject such combination with AP as primary interface.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Quantenna Pearl device exposes multiple (up to 3) radio interfaces under
single PCIe function. So far all the wiphy devices were attached to the
same pcie device. As a result, all different wireless network devices
were reported under the same sysfs directory for pcie device, e.g.:
$ ls /sys/class/net/wlan0/device/net/
wlan0 wlan1
It turns out that such behavior may confuse various users of wireless
subsystem. For instance, it turned out to be the case for:
- Linux init systems, e.g. for renaming based on parent device
- OpenWRT configuration scripts
Suggested solution is to add an intermediate virtual platform device
for each radio interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make sure that edmg field of cfg80211_chan_def structure is properly
initialized by zeros. Otherwise cfg80211_chandef_valid may return
false if edmg fields contain some garbage.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable WPA3 OWE support in AP mode. Driver currently supports cards that
offload OWE processing to userspace. This patch adds all the required
tools for such offloading. Firmware requests OWE processing sending new
UPDATE_OWE event to driver, which uses cfg80211_update_owe_info_event to
notify userspace software. After OWE processing is completed, userspace
sends calculated IEs to firmware using update_owe_info cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable WPA3 SAE support in AP mode. Driver currently supports cards
that offload SAE authentication to userspace. So allow userspace
software to subscribe and to send AUTH frames. Besides, enable
AP mode support in external_auth cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: ath11k@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Hardwares tested : QCA9887
Firmwares tested : 10.4-3.9.0.1-00036
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/emac/core.c: In function __emac_mdio_write:
drivers/net/ethernet/ibm/emac/core.c:875:9: warning:
variable err set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to play with gotos to jump over single statement.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 319a1d19471e, stmmac only support basic HW stats type for
action. Set this field in the L3/L4 Filtering test so that it correctly
setups the filter instead of returning EOPNOTSUPP.
Fixes: 319a1d19471e ("flow_offload: check for basic action hw stats type")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NCM specification defines two formats of transfer blocks: with 16-bit
fields (NTB-16) and with 32-bit fields (NTB-32). Currently only NTB-16 is
implemented.
This patch adds the support of NTB-32. The motivation behind this is that
some devices such as E5785 or E5885 from the current generation of Huawei
LTE routers do not support NTB-16. The previous generations of Huawei
devices are also use NTB-32 by default.
Also this patch enables NTB-32 by default for Huawei devices.
During the 2019 ValdikSS made five attempts to contact Huawei to add the
NTB-16 support to their router firmware, but they were unsuccessful.
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reverted commit "2baecda bareudp: remove unnecessary udp_encap_enable() in
bareudp_socket_create()"
An explicit call to udp_encap_enable is needed as the setup_udp_tunnel_sock
does not call udp_encap_enable if the if the socket is of type v6.
Bareudp device uses v6 socket to receive v4 & v6 traffic
CC: Taehee Yoo <ap420073@gmail.com>
Fixes: 2baecda37f4e ("bareudp: remove unnecessary udp_encap_enable() in bareudp_socket_create()")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this function, ftgmac100_probe() can be triggered only
if the platform_device and platform_driver matches, so the
judgement at the beginning is redundant.
Signed-off-by: tangbin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to
reconfigure HW's maximum txpower.
This fixes 0dBm txpower setting when user attaches to an interface for
the first time with the following scenario:
ieee80211_do_open()
ath9k_add_interface()
ath9k_set_txpower() /* Set TX power with not yet initialized
sc->hw->conf.power_level */
ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and
raise IEEE80211_CONF_CHANGE_POWER */
ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */
This issue can be reproduced with the following:
$ modprobe -r ath9k
$ modprobe ath9k
$ wpa_supplicant -i wlan0 -c /tmp/wpa.conf &
$ iw dev /* Here TX power is either 0 or 3 depending on RF chain */
$ killall wpa_supplicant
$ iw dev /* TX power goes back to calibrated value and subsequent
calls will be fine */
Fixes: 283dd11994cde ("ath9k: add per-vif TX power capability")
Cc: stable@vger.kernel.org
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The CONFIG_ATH5K_AHB could be enabled on ATH25 system without enabling
ATH5K driver itself. This does not make sense because CONFIG_ATH5K_AHB
controls object build within drivers/net/wireless/ath/ath5k/ so enabling
it without CONFIG_ATH5K brings nothing.
Add proper dependency to CONFIG_ATH5K_AHB.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When use command to read values, it crashed.
command:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value count=1 bs=4 skip=$((0x100233))
It will call to ath10k_sdio_hif_diag_read with address = 0x4008cc and buf_len = 4.
Then system crash:
[ 1786.013258] Unable to handle kernel paging request at virtual address ffffffc00bd45000
[ 1786.013273] Mem abort info:
[ 1786.013281] ESR = 0x96000045
[ 1786.013291] Exception class = DABT (current EL), IL = 32 bits
[ 1786.013299] SET = 0, FnV = 0
[ 1786.013307] EA = 0, S1PTW = 0
[ 1786.013314] Data abort info:
[ 1786.013322] ISV = 0, ISS = 0x00000045
[ 1786.013330] CM = 0, WnR = 1
[ 1786.013342] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 000000008542a60e
[ 1786.013350] [ffffffc00bd45000] pgd=0000000000000000, pud=0000000000000000
[ 1786.013368] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 1786.013609] Process swapper/0 (pid: 0, stack limit = 0x0000000084b153c6)
[ 1786.013623] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.86 #137
[ 1786.013631] Hardware name: MediaTek krane sku176 board (DT)
[ 1786.013643] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[ 1786.013662] pc : __memcpy+0x94/0x180
[ 1786.013678] lr : swiotlb_tbl_unmap_single+0x84/0x150
[ 1786.013686] sp : ffffff8008003c60
[ 1786.013694] x29: ffffff8008003c90 x28: ffffffae96411f80
[ 1786.013708] x27: ffffffae960d2018 x26: ffffff8019a4b9a8
[ 1786.013721] x25: 0000000000000000 x24: 0000000000000001
[ 1786.013734] x23: ffffffae96567000 x22: 00000000000051d4
[ 1786.013747] x21: 0000000000000000 x20: 00000000fe6e9000
[ 1786.013760] x19: 0000000000000004 x18: 0000000000000020
[ 1786.013773] x17: 0000000000000001 x16: 0000000000000000
[ 1786.013787] x15: 00000000ffffffff x14: 00000000000044c0
[ 1786.013800] x13: 0000000000365ba4 x12: 0000000000000000
[ 1786.013813] x11: 0000000000000001 x10: 00000037be6e9000
[ 1786.013826] x9 : ffffffc940000000 x8 : 000000000bd45000
[ 1786.013839] x7 : 0000000000000000 x6 : ffffffc00bd45000
[ 1786.013852] x5 : 0000000000000000 x4 : 0000000000000000
[ 1786.013865] x3 : 0000000000000c00 x2 : 0000000000000004
[ 1786.013878] x1 : fffffff7be6e9004 x0 : ffffffc00bd45000
[ 1786.013891] Call trace:
[ 1786.013903] __memcpy+0x94/0x180
[ 1786.013914] unmap_single+0x6c/0x84
[ 1786.013925] swiotlb_unmap_sg_attrs+0x54/0x80
[ 1786.013938] __swiotlb_unmap_sg_attrs+0x8c/0xa4
[ 1786.013952] msdc_unprepare_data+0x6c/0x84
[ 1786.013963] msdc_request_done+0x58/0x84
[ 1786.013974] msdc_data_xfer_done+0x1a0/0x1c8
[ 1786.013985] msdc_irq+0x12c/0x17c
[ 1786.013996] __handle_irq_event_percpu+0xe4/0x250
[ 1786.014006] handle_irq_event_percpu+0x28/0x68
[ 1786.014015] handle_irq_event+0x48/0x78
[ 1786.014026] handle_fasteoi_irq+0xd0/0x1a0
[ 1786.014039] __handle_domain_irq+0x84/0xc4
[ 1786.014050] gic_handle_irq+0x124/0x1a4
[ 1786.014059] el1_irq+0xb0/0x128
[ 1786.014072] cpuidle_enter_state+0x298/0x328
[ 1786.014082] cpuidle_enter+0x30/0x40
[ 1786.014094] do_idle+0x190/0x268
[ 1786.014104] cpu_startup_entry+0x24/0x28
[ 1786.014116] rest_init+0xd4/0xe0
[ 1786.014126] start_kernel+0x30c/0x38c
[ 1786.014139] Code: f8408423 f80084c3 36100062 b8404423 (b80044c3)
[ 1786.014150] ---[ end trace 3b02ddb698ea69ee ]---
[ 1786.015415] Kernel panic - not syncing: Fatal exception in interrupt
[ 1786.015433] SMP: stopping secondary CPUs
[ 1786.015447] Kernel Offset: 0x2e8d200000 from 0xffffff8008000000
[ 1786.015458] CPU features: 0x0,2188200c
[ 1786.015466] Memory Limit: none
For sdio chip, it need the memory which is kmalloc, if it is
vmalloc from ath10k_mem_value_read, then it have a memory error.
kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so
add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer
which is vmalloc from ath10k_mem_value_read.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject all unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject most of unsupported
parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
