Age | Commit message (Collapse) | Author |
|
LINK_UP and LINK_DOWN are two bits of MAC tunnel interrupts, but previous
HNS3 driver didn't handle them. If they were enabled, value of these two
bits will change during link down and link up, which will cause HNS3
driver keep receiving IRQ but can't handle them.
This patch adds handling of these two bits of interrupts, we will record
and clear them as what we do to other MAC tunnel interrupts.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hclge/hclgevf and hns3 module can be unloaded independently,
when hclge/hclgevf unloaded firstly, the ops of ae_dev should
be set to NULL, otherwise it will cause an use-after-free problem.
Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we add a VF without loading hclgevf.ko and then there is a RAS error
occurs, PCIe AER will call error_detected and slot_reset of all functions,
and will get a NULL pointer when we check ad_dev->ops->handle_hw_ras_error.
This will cause a call trace and failures on handling of follow-up RAS
errors.
This patch check ae_dev and ad_dev->ops at first to solve above issues.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch sets the port shaper according to the MAC speed as
suggested by hardware user manual.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In orginal codes, the driver only restore VLAN filter entries
for PF after reset, the VLAN entries of VF will lose in this
case.
This patch fixes it by recording VLAN IDs for each function
when add VLAN, and restore the VLAN IDs after reset.
Fixes: 681ec3999b3d ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF VLAN table can only support no more than 256 VLANs. When user
adds too many VLANs, the VF VLAN table will be full, and firmware
will close the VF VLAN table for the function. When VF VLAN table
is full, and user keeps adding new VLANs, it's unnecessary to
configure the VF VLAN table, because it will always fail, and print
warning message. The worst case is adding 4K VLANs, and doing reset,
it will take much time to restore these VLANs, which may cause VF
reset fail by timeout.
Fixes: 6c251711b37f ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since core reset is similar to the global reset, so this
patch removes it and uses global reset to replace it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use paged versions of phylib MDIO access functions to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix gcc build error while CONFIG_DEVLINK is not set
drivers/net/ethernet/qlogic/qed/qed_main.o: In function `qed_remove':
qed_main.c:(.text+0x1eb4): undefined reference to `devlink_unregister'
Select DEVLINK to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 24e04879abdd ("qed: Add qed devlink parameters table")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethernet support to MT7629 SoC
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All path route on various SoCs all would be managed in common function
mtk_setup_hw_path that is determined by the both applied devicetree
regarding the path between GMAC and the target PHY or switch by the
capability of target SoC in the runtime.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SGMII related logic into a separate file, and also provides options for
forcing 1G, 2.5, AN mode for the target PHY, that can be determined from
SGMII node in DTS.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-05-31
This series provides some updates to mlx5 core and netdevice driver.
1) use __netdev_tx_sent_queue() to improve performance under GSO workload
2) Allow matching only enc_key_id/enc_dst_port for decapsulation action
3) Geneve support:
This patchset adds support for GENEVE tunnel encap/decap flows offload:
encapsulating layer 2 Ethernet frames within layer 4 UDP datagrams.
The driver supports 6081 destination UDP port number, which is the
default IANA-assigned port.
Encap:
ConnectX-5 inserts the header (w/ or w/o Geneve TLV options) that is
provided by the mlx5 driver to the outgoing packet.
Decap:
Geneve header is matched and the packet is decapsulated.
Notes about decap flows with Geneve TLV Options:
- Support offloading of 32-bit options data only
- At any given time, only one combination of class/type parameters
can be offloaded, but the same class/type combination can have
many different flows offloaded with different 32-bit option data
- Options with value of 0 can't be offloaded
Managing Geneve TLV options:
Matching (on receive) is done by ConnectX-5 flex parser.
Geneve TLV options are managed using General Object of type
“Geneve TLV Options”.
When the first flow with a certain class/type values is requested
to be offloaded, the driver creates a FW object with FW command
(Geneve TLV Options general object) and starts counting the number
of flows using this object.
During this time, any request with a different class/type values
will fail to be offloaded.
Once the refcount reaches 0, the driver destroys the TLV options
general object, and can now offload a flow with any class/type parameters.
Geneve TLV Options object is added to core device.
It is currently used to manage Geneve TLV options general
object allocation in FW and its reference counting only.
In the future it will also be used for managing geneve ports
by registering callbacks for ndo_udp_tunnel_add/del.
TC tunnel code refactoring:
As a preparation for Geneve code, the TC tunnel code in mlx5
was rearranged in a modular way, so that it would be easier
to add future tunnels:
- Defined tc tunnel object with the fields and callbacks that
any tunnel must implement.
- Define tc UDP tunnel object for UDP tunnels, such as VXLAN
- Move each tunnel code (GRE, VXLAN) to its own separate file
- Rewrite tc tunnel implementation in a general way – using
only the objects and their callbacks.
4) Termination tables:
Actions in tables set with the termination flag are guaranteed to terminate
the action list. Thus, potential looping functionality (e.g. haripin) can safely be
executed without potential loops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new statistics to ETHTOOL to specify if the device calculated
and validated the Rx csum.
Signed-off-by: Evgeny Shmeilin <evgeny@annapurnaLabs.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch initially checks if CQ doorbell
is needed before proceeding with the calculations.
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now the driver always used a single setting for the sizes
of the different parts of the llq entry - 128 for entry size, 2 for
descriptors before header and 96 for maximum header size.
The current code makes sure that the parts of the llq entry are
compatible with each other and with the initial llq entry size given
by the device.
This commit changes this code to support any llq entry size
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable fallback to polling mode for Admin queue
when identified a command response arrival
without an accompanying MSI-X interrupt
Signed-off-by: Igor Chauskin <igorch@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some pr_err prints lacked '\n' in the end. Added where missing.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reverse christmas tree arrangement is when strings are written from longer
to shorter with each line. Most of our functions are abiding this
arrangement but this function does not.
In this commit we arrange the variables of ena_probe() in reverse christmas
tree.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct ena_ring holds a union of free_rx_ids and free_tx_ids.
Both of the above fields mean the exact same thing and are used
exactly the same way.
Furthermore, these fields are always used with a prefix of the
type of ring. So for tx it will be tx_ring->free_tx_ids, and for
rx it will be rx_ring->free_rx_ids, which shows how redundant the
"_tx" and "_rx" parts are.
Furthermore still, this may lead to confusing code like where
tx_ring->free_rx_ids which works correctly but looks like a mess.
This commit removes the aforementioned redundancy by replacing the
free_rx/tx_ids union with a single free_ids field.
It also changes a single goto label name from err_free_tx_ids: to
err_tx_free_ids: for consistency with the above new notation.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds a mechanism for exposing different device
properties via ethtool's priv_flags. The strings are provided
by the device and copied to user space through the driver.
In this commit we:
Add commands, structs and defines necessary for handling
extra properties
Add functions for:
Allocation/destruction of a buffer for extra properties strings.
Retreival of extra properties strings and flags from the network device.
Handle the allocation of a buffer for extra properties strings.
* Initialize buffer with extra properties strings from the
network device at driver startup.
Use ethtool's get_priv_flags to expose extra properties of
the ENA device
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a maximum TX burst size that the ENA device can handle.
It is exposed by the device to the driver and the driver
needs to comply with it to avoid bugs.
In this commit we:
1. Add ena_com_is_doorbell_needed(), which calculates the number of
llq entries that will be used to hold a packet, and will return
true if they exceed the number of allowed entries in a burst.
If the function returns true, a doorbell needs to be invoked
to send this packet in the next burst.
2. Follow the available entries in the current burst:
- Every doorbell a new burst begins
- With each write of an llq entry, the available entries in the
current burst are decreased by 1.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_g1_stats_wait has no users outside global1.c, so make it
static.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macros have an extraneous '800' (after 0180C2 there should be just
six nibbles, with X representing one), while the comments have
interchanged c2 and 80 and an extra :00.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace indirect call to tso_csum with direct calls. To do this we have
to move rtl_chip_supports_csum_v2().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The jumbo_ops are used in just one place, so we can simplify the code
and avoid the penalty of indirect calls in times of retpoline.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mdio_ops are used in just one place, so we can simplify the code
and avoid the penalty of indirect calls in times of retpoline.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use helper skb_is_gso() and simplify access to tx_dropped.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ifa_list is protected by rcu, yet code doesn't reflect this.
Add the __rcu annotations and fix up all places that are now reported by
sparse.
I've done this in the same commit to not add intermediate patches that
result in new warnings.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like previous patches, use the new iterator macros to avoid sparse
warnings once proper __rcu annotations are added.
Compile tested only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable rc is assigned with a value that is never read and
it is re-assigned a new value later on. The assignment is redundant
and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware offload of port filtering are now supported via tc command using
flower filter. ACL rules are used to enable the hardware offload.
The following keys are supported:
vlan_id
vlan_prio
dst_mac/src_mac for non IP frames
dst_ip/src_ip
dst_port/src_port
The following actions are supported:
trap
drop
These filters are supported only on the ingress schedulare.
Add:
tc qdisc add dev eth3 ingress
tc filter ad dev eth3 parent ffff: ip_proto ip flower \
ip_proto tcp dst_port 80 action drop
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ACL support using the TCAM. Using ACL it is possible to create rules
in hardware to filter/redirect frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-05-31
The following pull-request contains BPF updates for your *net-next* tree.
Lots of exciting new features in the first PR of this developement cycle!
The main changes are:
1) misc verifier improvements, from Alexei.
2) bpftool can now convert btf to valid C, from Andrii.
3) verifier can insert explicit ZEXT insn when requested by 32-bit JITs.
This feature greatly improves BPF speed on 32-bit architectures. From Jiong.
4) cgroups will now auto-detach bpf programs. This fixes issue of thousands
bpf programs got stuck in dying cgroups. From Roman.
5) new bpf_send_signal() helper, from Yonghong.
6) cgroup inet skb programs can signal CN to the stack, from Lawrence.
7) miscellaneous cleanups, from many developers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-05-31
This series contains updates to the iavf driver.
Nathan Chancellor converts the use of gnu_printf to printf.
Aleksandr modifies the driver to limit the number of RSS queues to the
number of online CPUs in order to avoid creating misconfigured RSS
queues.
Gustavo A. R. Silva converts a couple of instances where sizeof() can be
replaced with struct_size().
Alice makes the remaining changes to the iavf driver to cleanup all the
old "i40evf" references in the driver to iavf, including the file names
that still contained the old driver reference. There was no functional
changes made, just cosmetic to reduce any confusion going forward now
that the iavf driver is the virtual function driver for both i40e and
ice drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable err is assigned with the value -ENOMEM that is never
read and it is re-assigned a new value later on. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__netdev_tx_sent_queue() was introduced by:
commit 3e59020abf0f ("net: bql: add __netdev_tx_sent_queue()")
BQL counters should be updated without flipping/caring about
BQL status, if the current skb has xmit_more set.
Using __netdev_tx_sent_queue() avoids messing with BQL stop
flag, increases performance on GSO workload by keeping
doorbells to the minimum required and also sparing atomic
operations.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
HW does not support push VLAN action in the RX direction (packets
arriving from the wire). The FW works around this limitation by haripining
the packet. The hairpin workaround applies only when the push VLAN action
is specified in a termination table, assuring that there are no actions
following the haripin.
Instantiate termination table for push VLAN actions. Re-use identical
terminating tables for increased HW cache efficiency.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add HW offloading support for flows with Geneve encap/decap.
Notes about decap flows with Geneve TLV Options:
- Support offloading of 32-bit options data only
- At any given time, only one combination of class/type parameters
can be offloaded, but the same class/type combination can have
many different flows offloaded with different 32-bit option data
- Options with value of 0 can't be offloaded
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Rearrange tc tunnel code so that it would be easy to add future tunnels:
- Define tc tunnel object with the fields and callbacks that any
tunnel must implement.
- Define tc UDP tunnel object for UDP tunnels, such as VXLAN
- Move each tunnel code (GRE, VXLAN) to its own separate file
- Rewrite tc tunnel implementation in a general way - using only
the objects and their callbacks.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In mlx5e encap entry structure, IP tunnel info data structure is copied
by value. This approach worked till now, but it breaks when there are
encapsulation options, such as in case of Geneve.
These options are stored in the structure that is allocated adjacent to
the IP tunnel info struct, and not pointed at by any field in that struct.
Therefore, when copying the struct by value, we loose the address of the
original struct and can't get to the encapsulation options.
Fix the problem by storing the pointer to the tunnel info data instead.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use Geneve TLV Options object to manage the flex parser matching
on the 32-bit options data.
When the first flow with a certain class/type values is requested to
be offloaded, create a FW object with FW command (Geneve TLV Options
general object) and start counting the number of flows using this object.
During this time, any request with a different class/type values will
fail to be offloaded.
Once the refcount reaches 0, destroy the TLV options general object,
and can now offload a flow with any class/type parameters.
Geneve TLV Options object is added to core device.
It is currently used to manage Geneve TLV options general
object allocation in FW and its reference counting only.
In the future it will also be used for managing geneve ports
by registering callbacks for ndo_udp_tunnel_add/del.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When filling in flow spec match criteria, to allow previous
modifications of the match criteria, use "|=" rather than "=".
Tunnel options are parsed before the match criteria of the offloaded
flow are being set. If the the flow that we're about to offload has
encapsulation options, the flow group might need to match on additional
criteria.
For Geneve, an additional flow group matching parameter should
be used - misc3. The appropriate bit in the match criteria is set
while parsing the tunnel options, so the criteria value shouldn't
be overwritten.
This is a pre-step for supporting Geneve TLV options offload.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In some case, we don't care the enc_src_ip and enc_dst_ip, and
if we don't match the field enc_src_ip and enc_dst_ip, we can use
fewer flows in hardware when revice the tunnel packets. For example,
the tunnel packets may be sent from different hosts, we must offload
one rule for each host.
$ tc filter add dev vxlan0 protocol ip parent ffff: prio 1 \
flower dst_mac 00:11:22:33:44:00 \
enc_src_ip Host0_IP enc_dst_ip 2.2.2.100 \
enc_dst_port 4789 enc_key_id 100 \
action tunnel_key unset action mirred egress redirect dev eth0_1
$ tc filter add dev vxlan0 protocol ip parent ffff: prio 1 \
flower dst_mac 00:11:22:33:44:00 \
enc_src_ip Host1_IP enc_dst_ip 2.2.2.100 \
enc_dst_port 4789 enc_key_id 100 \
action tunnel_key unset action mirred egress redirect dev eth0_1
If we support flows which only match the enc_key_id and enc_dst_port,
a flow can process the packets sent to VM which (mac 00:11:22:33:44:00).
$ tc filter add dev vxlan0 protocol ip parent ffff: prio 1 \
flower dst_mac 00:11:22:33:44:00 \
enc_dst_port 4789 enc_key_id 100 \
action tunnel_key unset action mirred egress redirect dev eth0_1
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Beside the special vports (PF/uplink/ecpf), the rest of the vports
are similar.
Remove vf_ prefix from function and variable names.
This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
This series provides some low level updates for mlx5 driver needed for
both rdma and netdev trees.
1) Termination flow steering table bits and hardware definitions.
2) Introduce the core dump HW access registers definitions.
3) Refactor and cleans-up VF representors functions handlers.
4) Renames host_params bits to function_changed bits and add the
support for eswitch functions change event in the eswitch general case.
(for both legacy and switchdev modes).
5) Potential error pointer dereference in error handling
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The sfp-bus code now no longer has any use for the network device
structure, so remove its use.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add attach and detach methods for SFP buses, which will allow us to get
rid of the netdev storage in sfp-bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow userspace to generate Clause 45 MII access cycles via phylib.
This is useful for tools such as mii-diag to be able to inspect Clause
45 PHYs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|