Age | Commit message (Collapse) | Author |
|
This change enables the use of SW timestamping on Raspberry PI.
smsc95xx uses the usbnet transmit function usbnet_start_xmit(), which
implements software timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE
capability was missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced.
By using ethtool_op_get_ts_info() as get_ts_info() also the
SOF_TIMESTAMPING_TX_SOFTWARE is announced.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some firmwares in Huawei E3372H devices have been observed to switch back
to NTB 32-bit format after altsetting switch.
This patch implements a driver flag to check for the device settings and
set NTB format to 16-bit again if needed.
The flag has been activated for devices controlled by the huawei_cdc_ncm.c
driver.
V1->V2:
- fixed broken error checks
- some corrections to the commit message
V2->V3:
- variable name changes, to clarify what's happening
- check (and possibly set) the NTB format later in the common bind code path
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-and-tested-by: Christian Panton <christian@panton.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
CC: Bjørn Mork <bjorn@mork.no>
CC: Christian Panton <christian@panton.org>
CC: linux-usb@vger.kernel.org
CC: netdev@vger.kernel.org
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HP lt4132 LTE/HSPA+ 4G Module (03f0:a31d) is a rebranded Huawei
ME906s-158 device. It, like the ME906s-158, requires the "NDP to end"
quirk for correct operation.
Signed-off-by: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CDC-NCM driver can require large amounts of memory to create
skb's and this can be a problem when the memory becomes fragmented.
This especially affects embedded systems that have constrained
resources but wish to maximise the throughput of CDC-NCM with 16KiB
NTB's.
The issue is after running for a while the kernel memory can become
fragmented and it needs compacting.
If the NTB allocation is needed before the memory has been compacted
the atomic allocation can fail which can cause increased latency,
large re-transmissions or disconnections depending upon the data
being transmitted at the time.
This situation occurs for less than a second until the kernel has
compacted the memory but the failed devices can take a lot longer to
recover from the failed TX packets.
To ease this temporary situation I modified the CDC-NCM TX path to
temporarily switch into a reduced memory mode which allocates an NTB
that will fit into a USB_CDC_NCM_NTB_MIN_OUT_SIZE (default 2048 Bytes)
sized memory block and only transmit NTB's with a single network frame
until the memory situation is resolved.
Each time this issue occurs we wait for an increasing number of
reduced size allocations before requesting a full size one to not
put additional pressure on a low memory system.
Once the memory is compacted the CDC-NCM data can resume transmitting
at the normal tx_max rate once again.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A set of overlapping changes in macvlan and the rocker
driver, nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Belkin B2B128 is a USB 3.0 Hub + Gigabit Ethernet Adapter, the
Ethernet adapter uses the ASIX AX88179 USB 3.0 to Gigabit Ethernet
chip supported by this driver, add the USB ID for the same.
This patch is based on work by Geoffrey Tran <geoffrey.tran@gmail.com>
who has indicated they would like this upstreamed by someone more
familiar with the upstreaming process.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace VLAN_HLEN and CRC_SIZE with ETH_FCS_LEN.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
spatch file,
@@
expression skb, len, data;
type t;
@@
-memcpy((t *)skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(skb_put(skb, len), data, len);
+p = skb_put_zero(skb, len);
@@
expression skb, len, data;
type t;
@@
-memcpy((t *)__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);
@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(__skb_put(skb, len), data, len);
+p = __skb_put_zero(skb, len);
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
follow Johannes Berg, semantic patch file as below,
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = __skb_put(skb, len);
+p = __skb_put_zero(skb, len);
|
-p = (t)__skb_put(skb, len);
+p = __skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
identifier p;
expression len;
expression skb;
type t;
@@
(
-t p = __skb_put(skb, len);
+t p = __skb_put_zero(skb, len);
)
... when != p
(
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = __skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
|
-p = (t *)__skb_put(skb, sizeof(t));
+p = __skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(__skb_put(skb, len), 0, len);
+__skb_put_zero(skb, len);
@@
expression skb, len, data;
@@
-memcpy(__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);
@@
expression SKB, C, S;
typedef u8;
identifier fn = {__skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Joe and Bjørn suggested that it'd be nicer to not have the
cast in the fairly common case of doing
*(u8 *)skb_put(skb, 1) = c;
Add skb_put_u8() for this case, and use it across the code,
using the following spatch:
@@
expression SKB, C, S;
typedef u8;
identifier fn = {skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Note that due to the "S", the spatch isn't perfect, it should
have checked that S is 1, but there's also places that use a
sizeof expression like sizeof(var) or sizeof(u8) etc. Turns
out that nobody ever did something like
*(u8 *)skb_put(skb, 2) = c;
which would be wrong anyway since the second byte wouldn't be
initialized.
Suggested-by: Joe Perches <joe@perches.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move calling delay_autosuspend() in rtl8152_runtime_suspend(). Calling
delay_autosuspend() as late as possible.
The original flows are
1. check if the driver/device is busy now.
2. set wake events.
3. enter runtime suspend.
If the wake event occurs between (1) and (2), the device may miss it. Besides,
to avoid the runtime resume occurs after runtime suspend immediately, move the
checking to the end of rtl8152_runtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split rtl8152_resume() into rtl8152_runtime_resume() and
rtl8152_system_resume().
Besides, replace GFP_KERNEL with GFP_NOIO for usb_submit_urb().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add byte_enable for ocp_read_word() to replace reading 4
bytes data with reading the desired 2 bytes data.
This is used to avoid the issue which is described in
commit b4d99def0938 ("r8152: remove sram_read"). The
original method always reads 4 bytes data, and it may
have problem when reading the PHY registers.
The new method is supported since RTL8153B, but it
doesn't influence the previous chips. The bits of the
byte_enable for the previous chips are the reserved
bits, and the hw would ignore them.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch supports two new chips for RTL8153B.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The settings of the new chip are the same with RTL8152, except that
its product ID is 0x8050.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The conflicts were two cases of overlapping changes in
batman-adv and the qed driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Getting the device version out of the driver really aids debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop queuing rx packets if it is more than 1000.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use PLA 0xe000 bit 8 to check if disabling ALDPS is finished.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move tp->rtl_ops.init() from rtl8152_resume() to rtl8152_reset_resume().
The initialization is only necessary for reset_resume().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only RTL8153 could set coalesce, so move the default setting for
rtl8152_probe() to r8153_init().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use another way to keep disabling the U2P3 for both RTL_VER_03 and
RTL_VER_04.
Move enabling U2P3 from r8153_init() to r8153_hw_phy_cfg(). The
engineer ask the setting should be done after PHY settings.
Disable U2P3 first in rtl8153_up().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC clock speed down could be enabled if the U1/U2 is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable lpm after r8153_init() and remove other enable/disable lpm.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use r8153_phy_status() to check phy status of RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
return void
Make return value void since functions never returns meaningfull value.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some devices need their multicast filter reset but others are crashed by that.
So the methods need to be separated.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: "Ridgway, Keith" <kridgway@harris.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When TX checksum offload is used, if the computed checksum is 0 the
LAN95xx device do not alter the checksum to 0xffff. In the case of ipv4
UDP checksum, it indicates to receiver that no checksum is calculated.
Under ipv6, UDP checksum yields a result of zero must be changed to
0xffff. Hence disabling checksum offload for ipv6 packets.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Reported-by: popcorn mix <popcornmix@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/net1080.c:271:20: error: unused function
'nc_dump_ttl' [-Werror,-Wunused-function]
Also remove the definition of TTL_THIS, which is only used in
nc_dump_ttl()
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/r8152.c:825:5: error: unused function 'usb_ocp_read'
[-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing endianness conversions to a debug statement printing
the USB device-descriptor idVendor and idProduct fields during probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The zero padding that is added to NTB's does
not zero the memory correctly.
This is because the skb_put modifies the value
of skb_out->len which results in the memset
command not setting any memory to zero as
(ctx->tx_max - skb_out->len) == 0.
I have resolved this by storing the size of
the memory to be zeroed before the skb_put
and using this in the memset call.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for Telit ME910 PID 0x1100.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
|
|
If the netdev is accessed before the urbs are initialized,
there will be NULL pointer dereferences. That is avoided by
registering it when it is fully initialized.
This case occurs e.g. if dhcpcd is running in the background
and the device is probed, either after insmod hso or
when the device appears on the usb bus.
A backtrace is the following:
[ 1357.356048] usb 1-2: new high-speed USB device number 12 using ehci-omap
[ 1357.551177] usb 1-2: New USB device found, idVendor=0af0, idProduct=8800
[ 1357.558654] usb 1-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0
[ 1357.568572] usb 1-2: Product: Globetrotter HSUPA Modem
[ 1357.574096] usb 1-2: Manufacturer: Option N.V.
[ 1357.685882] hso 1-2:1.5: Not our interface
[ 1460.886352] hso: unloaded
[ 1460.889984] usbcore: deregistering interface driver hso
[ 1513.769134] hso: ../drivers/net/usb/hso.c: Option Wireless
[ 1513.846771] Unable to handle kernel NULL pointer dereference at virtual address 00000030
[ 1513.887664] hso 1-2:1.5: Not our interface
[ 1513.906890] usbcore: registered new interface driver hso
[ 1513.937988] pgd = ecdec000
[ 1513.949890] [00000030] *pgd=acd15831, *pte=00000000, *ppte=00000000
[ 1513.956573] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 1513.962371] Modules linked in: hso usb_f_ecm omap2430 bnep bluetooth g_ether usb_f_rndis u_ether libcomposite configfs ipv6 arc4 wl18xx wlcore mac80211 cfg80211 bq27xxx_battery panel_tpo_td028ttec1 omapdrm drm_kms_helper cfbfillrect snd_soc_simple_card syscopyarea cfbimgblt snd_soc_simple_card_utils sysfillrect sysimgblt fb_sys_fops snd_soc_omap_twl4030 cfbcopyarea encoder_opa362 drm twl4030_madc_hwmon wwan_on_off snd_soc_gtm601 pwm_omap_dmtimer generic_adc_battery connector_analog_tv pwm_bl extcon_gpio omap3_isp wlcore_sdio videobuf2_dma_contig videobuf2_memops w1_bq27000 videobuf2_v4l2 videobuf2_core omap_hdq snd_soc_omap_mcbsp ov9650 snd_soc_omap bmp280_i2c bmg160_i2c v4l2_common snd_pcm_dmaengine bmp280 bmg160_core at24 bmc150_magn_i2c nvmem_core videodev phy_twl4030_usb bmc150_accel_i2c tsc2007
[ 1514.037384] bmc150_magn bmc150_accel_core media leds_tca6507 bno055 industrialio_triggered_buffer kfifo_buf gpio_twl4030 musb_hdrc snd_soc_twl4030 twl4030_vibra twl4030_madc twl4030_pwrbutton twl4030_charger industrialio w2sg0004 ehci_omap omapdss [last unloaded: hso]
[ 1514.062622] CPU: 0 PID: 3433 Comm: dhcpcd Tainted: G W 4.11.0-rc8-letux+ #1
[ 1514.071136] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[ 1514.077758] task: ee748240 task.stack: ecdd6000
[ 1514.082580] PC is at hso_start_net_device+0x50/0xc0 [hso]
[ 1514.088287] LR is at hso_net_open+0x68/0x84 [hso]
[ 1514.093231] pc : [<bf79c304>] lr : [<bf79ced8>] psr: a00f0013
sp : ecdd7e20 ip : 00000000 fp : ffffffff
[ 1514.105316] r10: 00000000 r9 : ed0e080c r8 : ecd8fe2c
[ 1514.110839] r7 : bf79cef4 r6 : ecd8fe00 r5 : 00000000 r4 : ed0dbd80
[ 1514.117706] r3 : 00000000 r2 : c0020c80 r1 : 00000000 r0 : ecdb7800
[ 1514.124572] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 1514.132110] Control: 10c5387d Table: acdec019 DAC: 00000051
[ 1514.138153] Process dhcpcd (pid: 3433, stack limit = 0xecdd6218)
[ 1514.144470] Stack: (0xecdd7e20 to 0xecdd8000)
[ 1514.149078] 7e20: ed0dbd80 ecd8fe98 00000001 00000000 ecd8f800 ecd8fe00 ecd8fe60 00000000
[ 1514.157714] 7e40: ed0e080c bf79ced8 bf79ce70 ecd8f800 00000001 bf7a0258 ecd8f830 c068d958
[ 1514.166320] 7e60: c068d8b8 ecd8f800 00000001 00001091 00001090 c068dba4 ecd8f800 00001090
[ 1514.174926] 7e80: ecd8f940 ecd8f800 00000000 c068dc60 00000000 00000001 ed0e0800 ecd8f800
[ 1514.183563] 7ea0: 00000000 c06feaa8 c0ca39c2 beea57dc 00000020 00000000 306f7368 00000000
[ 1514.192169] 7ec0: 00000000 00000000 00001091 00000000 00000000 00000000 00000000 00008914
[ 1514.200805] 7ee0: eaa9ab60 beea57dc c0c9bfc0 eaa9ab40 00000006 00000000 00046858 c066a948
[ 1514.209411] 7f00: beea57dc eaa9ab60 ecc6b0c0 c02837b0 00000006 c0282c90 0000c000 c0283654
[ 1514.218017] 7f20: c09b0c00 c098bc31 00000001 c0c5e513 c0c5e513 00000000 c0151354 c01a20c0
[ 1514.226654] 7f40: c0c5e513 c01a3134 ecdd6000 c01a3160 ee7487f0 600f0013 00000000 ee748240
[ 1514.235260] 7f60: ee748734 00000000 ecc6b0c0 ecc6b0c0 beea57dc 00008914 00000006 00000000
[ 1514.243896] 7f80: 00046858 c02837b0 00001091 0003a1f0 00046608 0003a248 00000036 c01071e4
[ 1514.252502] 7fa0: ecdd6000 c0107040 0003a1f0 00046608 00000006 00008914 beea57dc 00001091
[ 1514.261108] 7fc0: 0003a1f0 00046608 0003a248 00000036 0003ac0c 00046608 00046610 00046858
[ 1514.269744] 7fe0: 0003a0ac beea57d4 000167eb b6f23106 400f0030 00000006 00000000 00000000
[ 1514.278411] [<bf79c304>] (hso_start_net_device [hso]) from [<bf79ced8>] (hso_net_open+0x68/0x84 [hso])
[ 1514.288238] [<bf79ced8>] (hso_net_open [hso]) from [<c068d958>] (__dev_open+0xa0/0xf4)
[ 1514.296600] [<c068d958>] (__dev_open) from [<c068dba4>] (__dev_change_flags+0x8c/0x130)
[ 1514.305023] [<c068dba4>] (__dev_change_flags) from [<c068dc60>] (dev_change_flags+0x18/0x48)
[ 1514.313934] [<c068dc60>] (dev_change_flags) from [<c06feaa8>] (devinet_ioctl+0x348/0x714)
[ 1514.322540] [<c06feaa8>] (devinet_ioctl) from [<c066a948>] (sock_ioctl+0x2b0/0x308)
[ 1514.330627] [<c066a948>] (sock_ioctl) from [<c0282c90>] (vfs_ioctl+0x20/0x34)
[ 1514.338165] [<c0282c90>] (vfs_ioctl) from [<c0283654>] (do_vfs_ioctl+0x82c/0x93c)
[ 1514.346038] [<c0283654>] (do_vfs_ioctl) from [<c02837b0>] (SyS_ioctl+0x4c/0x74)
[ 1514.353759] [<c02837b0>] (SyS_ioctl) from [<c0107040>] (ret_fast_syscall+0x0/0x1c)
[ 1514.361755] Code: e3822103 e3822080 e1822781 e5981014 (e5832030)
[ 1514.510833] ---[ end trace dfb3e53c657f34a0 ]---
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|