Age | Commit message (Collapse) | Author |
|
We face an issue with rtl8211f, a pin is shared between INTB and PMEB,
and the PHY Register Accessible Interrupt is enabled by default, so
the INTB/PMEB pin is always active in polling mode case.
As Heiner pointed out "I was thinking about calling
phy_disable_interrupts() in phy_init_hw(), to have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state."
Make phy_disable_interrupts() non-static so that it could be used in
phy_init_hw() to have a defined init state.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function was introduced to allow for different handling of
link up and link down events particularly with regard to the
netif_carrier. The third argument do_carrier allowed the flag to
be left unchanged.
Since then the phylink has introduced an implementation that
completely ignores the third parameter since it never wants to
change the flag and the phylib always sets the third parameter
to true so the flag is always changed.
Therefore the third argument (i.e. do_carrier) is no longer
necessary and can be removed. This also means that the phylib
phy_link_down() function no longer needs its second argument.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.
Fixes: f75abeb8338e ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since running a cable test is disruptive, put the interface into
operative state testing while the test is running.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some PHYs are not capable of generating interrupts when a cable test
finished. They do however support interrupts for normal operations,
like link up/down. As such, the PHY state machine would normally not
poll the PHY.
Add support for indicating the PHY state machine must poll the PHY
when performing a cable test.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Running a cable test is desruptive to normal operation of the PHY and
can take a 5 to 10 seconds to complete. The RTNL lock cannot be held
for this amount of time, and add a new state to the state machine for
running a cable test.
The driver is expected to implement two functions. The first is used
to start a cable test. Once the test has started, it should return.
The second function is called once per second, or on interrupt to
check if the cable test is complete, and to allow the PHY to report
the status.
v2:
Rename phy_cable_test_abort to phy_abort_cable_test
Return different extack when already running test
Use phy_init_hw() to reset the PHY
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2:
- Add downshift hint to phy_print_status
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.
Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On all PHY drivers that implement did_interrupt() reading the interrupt
status bits clears them. This means we may loose an interrupt that
is triggered between calling did_interrupt() and phy_clear_interrupt().
As part of the fix make it a requirement that did_interrupt() clears
the interrupt.
The Fixes tag refers to the first commit where the patch applies
cleanly.
Fixes: 49644e68f472 ("net: phy: add callback for custom interrupt handler to struct phy_driver")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new version of phy_do_ioctl that doesn't check whether net_device
is running. It will typically be used if suitable drivers attach the
PHY in probe already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of network drivers has the same glue code to use phy_mii_ioctl
as ndo_do_ioctl handler. So let's add such a generic ndo_do_ioctl
handler to phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no users of phy_ethtool_sset() in the kernel anymore, and
as of commit 3c1bcc8614db ("net: ethernet: Convert phydev advertize
and supported from u32 to link mode"), the implementation is slightly
buggy - it doesn't correctly check the masked advertising mask as it
used to.
Remove it, and update the phy documentation to refer to its replacement
function.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation. However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither. This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.
Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While running stmmac selftests I found that in my 1G setup some tests
were failling when running with PHY loopback enabled.
It looks like when loopback is enabled the PHY will report that Link is
down even though there is a valid connection.
As in loopback mode the data will not be sent anywhere we can bypass the
logic of checking if Link is valid thus saving unecessary reads.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
r8152 conflicts are the NAPI fixes in 'net' overlapping with
some tasklet stuff in net-next
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some ethernet drivers may call phy_start() and phy_stop() from
ndo_open() and ndo_close() respectively.
When network cable is unconnected, and operate like below:
step 1: ifconfig ethX up -> ndo_open -> phy_start ->start
autoneg, and phy is no link.
step 2: ifconfig ethX down -> ndo_close -> phy_stop -> just stop
phy state machine.
This patch forces phy suspend even phydev->link is off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 34786005eca3 ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e827093 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
linkmode_mod_bit is introduced as a helper function to set/clear
bits in a linkmode.
Replace the if else code structure with a call to the helper
linkmode_mod_bit.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the early days of phylib we had a functionality that changed to the
next lower speed in fixed mode if no link was established after a
certain period of time. This functionality has been removed years ago,
and state PHY_FORCING isn't needed any longer. Instead we can go from
UP to RUNNING or NOLINK directly (same as in autoneg mode).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow userspace to generate Clause 45 MII access cycles via phylib.
This is useful for tools such as mii-diag to be able to inspect Clause
45 PHYs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We face the issue that link change interrupt and link status may be
reported by different PHY layers. As a result the link change
interrupt may occur before the link status changes.
Export phy_queue_state_machine to allow PHY drivers to specify a
delay between link status change interrupt and link status check.
v2:
- change jiffies parameter type to unsigned long
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phylib interrupt handler handles link change events only currently.
However PHY drivers may want to use other interrupt sources too,
e.g. to report temperature monitoring events. Therefore add a callback
to struct phy_driver allowing PHY drivers to implement a custom
interrupt handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().
v2:
- patch added to series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we report symmetric pause only, and we don't consider the local
pause capabilities. Let's properly consider local and remote
capabilities, and report also asymmetric pause.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_sanitize_settings() is called from phy_start_aneg() only, and only
if phydev->autoneg isn't set. Therefore the removed code does nothing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the Phy driver's link_change_notify callback is called
whenever the state machine is run (every second if polling), no matter
whether the state changed or not. This isn't needed and may confuse
users considering the name of the callback. Actually it contradicts
its kernel-doc description. Therefore let's change the behavior and
call this callback only in case of an actual state change.
This requires changes to the at803x and rockchip drivers.
at803x can be simplified so that it reacts on a state change to
PHY_NOLINK only.
The rockchip driver can also be much simplified. We simply re-init
the AFE/DSP registers whenever we change to PHY_RUNNING and speed
is 100Mbps. This causes very small overhead because we do this even
if the speed was 100Mbps already. But this is negligible and
I think justified by the much simpler code.
Changes are compile-tested only.
A little bit problematic seems to be to find somebody with the
hardware to test the changes to the two PHY drivers. See also [0].
David may be able to test the Rockchip driver.
[0] https://marc.info/?t=153782508800006&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Russell reported the following race in the phylib state machine
(quoting from his mail):
if (phy_polling_mode(phydev) && phy_is_started(phydev))
phy_queue_state_machine(phydev, PHY_STATE_TIME);
state = PHY_UP
thread 0 thread 1
phy_disconnect()
+-phy_is_started()
phy_is_started() |
`-phy_stop()
+-phydev->state = PHY_HALTED
`-phy_stop_machine()
`-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()
At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.
Fix this by protecting the complete operation in thread 0.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the new MMD accessors.
v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we enable the interrupts in phy_start() we don't have to do it
before. Therefore remove enabling interrupts from phy_start_interrupts()
and rename this function to reflect the changed functionality.
v2:
- improve warning to clearly state that we fall back to polling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupts don't have to be enabled before calling phy_start().
Therefore let's enable them in phy_start(). In a subsequent step
we'll remove enabling interrupts from phy_connect_direct().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_start() should be called from states PHY_READY or PHY_HALTED only.
Check for this to detect misbehaving drivers. Also the state machine
should be started only when being called from one of the valid states.
Some more background:
For all invalid states phy_start() basically was a no-op. All it did
was triggering a state machine run, but for all "running" states the
poll loop was active anyway. And if called from PHY_DOWN, the state
machine does nothing.
v3:
- extended commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The state machine is a no-op before phy_start() has been called.
Therefore let's enable it in phy_start() only. In phy_start()
let's call phy_start_machine() instead of phy_trigger_machine().
phy_start_machine is an alias for phy_trigger_machine but it makes
clearer that we start the state machine here instead of just
triggering a run.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Completely minor snmp doc conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|