| Age | Commit message (Collapse) | Author |
|---|
|
ugeth is the netdiv_priv() part of the netdevice. Accessing the memory
pointed to by ugeth (such as done by ucc_geth_memclean() and the two
of_node_puts) after free_netdev() is thus use-after-free.
Fixes: 80a9fad8e89a ("ucc_geth: fix module removal")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All the buffers and registers are already set up appropriately for an
MTU slightly above 1500, so we just need to expose this to the
networking stack. AFAICT, there's no need to implement .ndo_change_mtu
when the receive buffers are always set up to support the max_mtu.
This fixes several warnings during boot on our mpc8309-board with an
embedded mv88e6250 switch:
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 0
...
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 4
ucc_geth e0102000.ethernet eth1: error -22 setting MTU to 1504 to include DSA overhead
The last line explains what the DSA stack tries to do: achieving an MTU
of 1500 on-the-wire requires that the master netdevice connected to
the CPU port supports an MTU of 1500+the tagging overhead.
Fixes: bfcb813203e6 ("net: dsa: configure the MTU for switch ports")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch fixes an error condition triggered when the code path which
transmits a S/G frame descriptor when the skb's headroom is not enough
for DPAA2's needs.
We are greated with a splat like the one below when a SGT structure is
recycled and that is because even though a dma_unmap is performed on the
Tx confirmation path, the unmap is not done with the proper size.
[ 714.464927] WARNING: CPU: 13 PID: 0 at drivers/iommu/io-pgtable-arm.c:281 __arm_lpae_map+0x2d4/0x30c
(...)
[ 714.465343] Call trace:
[ 714.465348] __arm_lpae_map+0x2d4/0x30c
[ 714.465353] __arm_lpae_map+0x114/0x30c
[ 714.465357] __arm_lpae_map+0x114/0x30c
[ 714.465362] __arm_lpae_map+0x114/0x30c
[ 714.465366] arm_lpae_map+0xf4/0x180
[ 714.465373] arm_smmu_map+0x4c/0xc0
[ 714.465379] __iommu_map+0x100/0x2bc
[ 714.465385] iommu_map_atomic+0x20/0x30
[ 714.465391] __iommu_dma_map+0xb0/0x110
[ 714.465397] iommu_dma_map_page+0xb8/0x120
[ 714.465404] dma_map_page_attrs+0x1a8/0x210
[ 714.465413] __dpaa2_eth_tx+0x384/0xbd0 [fsl_dpaa2_eth]
[ 714.465421] dpaa2_eth_tx+0x84/0x134 [fsl_dpaa2_eth]
[ 714.465427] dev_hard_start_xmit+0x10c/0x2b0
[ 714.465433] sch_direct_xmit+0x1a0/0x550
(...)
The dpaa2-eth driver uses an area of software annotations to transmit
necessary information from the Tx path to the Tx confirmation one. This
SWA structure has a different layout for each kind of frame that we are
dealing with: linear, S/G or XDP.
The commit referenced was incorrectly setting up the 'sgt_size' field
for the S/G type of SWA even though we are dealing with a linear skb
here.
Fixes: d70446ee1f40 ("dpaa2-eth: send a scatter-gather FD instead of realloc-ing")
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201211171607.108034-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an 'of_node_put()' call when a tested device node is not available.
Fixes: 94ae899b2096 ("dpaa2-mac: add PCS support through the Lynx module")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201206151339.44306-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Noticed some inconsistencies in packet statistics reporting.
This patch adds the missing Tx packet counter registers to
ethtool reporting and fixes the information strings for a
few of them.
Fixes: 16eb4c85c964 ("enetc: Add ethtool statistics")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204171505.21389-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When CONFIG_OF is disabled, there is a harmless warning about
an unused variable:
enetc_pf.c: In function 'enetc_phylink_create':
enetc_pf.c:981:17: error: unused variable 'dev' [-Werror=unused-variable]
Slightly rearrange the code to pass around the of_node as a
function argument, which avoids the problem without hurting
readability.
Fixes: 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204120800.17193-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A number of ethernet drivers require crc32 functionality to be
avaialable in the kernel, causing a link error otherwise:
arm-linux-gnueabi-ld: drivers/net/ethernet/agere/et131x.o: in function `et1310_setup_device_for_multicast':
et131x.c:(.text+0x5918): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/cadence/macb_main.o: in function `macb_start_xmit':
macb_main.c:(.text+0x4b88): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/faraday/ftgmac100.o: in function `ftgmac100_set_rx_mode':
ftgmac100.c:(.text+0x2b38): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fec_main.o: in function `set_multicast_list':
fec_main.c:(.text+0x6120): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o: in function `dtsec_add_hash_mac_address':
fman_dtsec.c:(.text+0x830): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o:fman_dtsec.c:(.text+0xb68): more undefined references to `crc32_le' follow
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_hwinfo.o: in function `nfp_hwinfo_read':
nfp_hwinfo.c:(.text+0x250): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_hwinfo.c:(.text+0x288): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_resource.o: in function `nfp_resource_acquire':
nfp_resource.c:(.text+0x144): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_resource.c:(.text+0x158): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/nxp/lpc_eth.o: in function `lpc_eth_set_multicast_list':
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_do':
rocker_ofdpa.c:(.text+0x2e08): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_del':
rocker_ofdpa.c:(.text+0x3074): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_port_fdb':
arm-linux-gnueabi-ld: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.o: in function `mlx5dr_ste_calc_hash_index':
dr_ste.c:(.text+0x354): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_netdev_set_multicast':
lan743x_main.c:(.text+0x5dc4): undefined reference to `crc32_le'
Add the missing 'select CRC32' entries in Kconfig for each of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201203232114.1485603-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When building FSL_DPAA_ETH the following build error shows up:
/tmp/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function ‘dpaa_fq_init’:
/tmp/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1135:9: error: too few arguments to function ‘xdp_rxq_info_reg’
1135 | err = xdp_rxq_info_reg(&dpaa_fq->xdp_rxq, dpaa_fq->net_dev,
| ^~~~~~~~~~~~~~~~
Commit b02e5a0ebb17 ("xsk: Propagate napi_id to XDP socket Rx path")
added an extra argument to function xdp_rxq_info_reg and commit
d57e57d0cd04 ("dpaa_eth: add XDP_TX support") didn't know about that
extra argument.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20201203144343.790719-1-anders.roxell@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
drivers/net/ethernet/ibm/ibmvnic.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The timestamp fields should be copied to new skb too in
A-050385 workaround for later TX timestamping handling.
Fixes: 3c68b8fffb48 ("dpaa_eth: FMan erratum A050385 workaround")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Link: https://lore.kernel.org/r/20201201075258.1875-1-yangbo.lu@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This was added in commit ce973b141dfa ("[PATCH] Freescale QE UCC gigabit
ethernet driver") but doesn't appear to have been used. Remove it now.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20201130001010.28998-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For XDP TX, even tough we start out with correctly aligned buffers, the
XDP program might change the data's alignment. For REDIRECT, we have no
control over the alignment either.
Create a new workaround for xdp_frame structures to verify the erratum
conditions and move the data to a fresh buffer if necessary. Create a new
xdp_frame for managing the new buffer and free the old one using the XDP
API.
Due to alignment constraints, all frames have a 256 byte headroom that
is offered fully to XDP under the erratum. If the XDP program uses all
of it, the data needs to be move to make room for the xdpf backpointer.
Disable the metadata support since the information can be lost.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Explicitly point that the current workaround addresses skbs. This change is
in preparation for adding a workaround for XDP scenarios.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After transmission, the frame is returned on confirmation queues for
cleanup. For this, store a backpointer to the xdp_frame in the private
reserved area at the start of the TX buffer.
No TX batching support is implemented at this time.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use an xdp_frame structure for managing the frame. Store a backpointer to
the structure at the start of the buffer before enqueueing for cleanup
on TX confirmation. Reserve DPAA_TX_PRIV_DATA_SIZE bytes from the frame
size shared with the XDP program for this purpose. Use the XDP
API for freeing the buffer when it returns to the driver on the TX
confirmation path.
The frame queues are shared with the netstack. The DPAA driver is a LLTX
driver so no explicit locking is required on transmission.
This approach will be reused for XDP REDIRECT.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the ndo_change_mtu callback to prevent users from setting an
MTU that would permit processing of S/G frames. The maximum MTU size
is dependent on the buffer size.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the XDP_DROP and XDP_PASS actions.
Avoid draining and reconfiguring the buffer pool at each XDP
setup/teardown by increasing the frame headroom and reserving
XDP_PACKET_HEADROOM bytes from the start. Since we always reserve an
entire page per buffer, this change only impacts Jumbo frame scenarios
where the maximum linear frame size is reduced by 256 bytes. Multi
buffer Scatter/Gather frames are now used instead in these scenarios.
Allow XDP programs to access the entire buffer.
The data in the received frame's headroom can be overwritten by the XDP
program. Extract the relevant fields from the headroom while they are
still available, before running the XDP program.
Since the headroom might be resized before the frame is passed up to the
stack, remove the check for a fixed headroom value when building an skb.
Allow the meta data to be updated and pass the information up the stack.
Scatter/Gather frames are dropped when XDP is enabled.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We maintain an skb backpointer in the software annotations area of Tx
frames. Introduce a structure for explicit handling.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
|
|
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The tc-taprio base time indicates the beginning of the tc-taprio
schedule, which is cyclic by definition (where the length of the cycle
in nanoseconds is called the cycle time). The base time is a 64-bit PTP
time in the TAI domain.
Logically, the base-time should be a future time. But that imposes some
restrictions to user space, which has to retrieve the current PTP time
from the NIC first, then calculate a base time that will still be larger
than the base time by the time the kernel driver programs this value
into the hardware. Actually ensuring that the programmed base time is in
the future is still a problem even if the kernel alone deals with this.
Luckily, the enetc hardware already advances a base-time that is in the
past into a congruent time in the immediate future, according to the
same formula that can be found in the software implementation of taprio
(in taprio_get_start_time):
/* Schedule the start time for the beginning of the next
* cycle.
*/
n = div64_s64(ktime_sub_ns(now, base), cycle);
*start = ktime_add_ns(base, (n + 1) * cycle);
There's only one problem: the driver doesn't let the hardware do that.
It interferes with the base-time passed from user space, by special-casing
the situation when the base-time is zero, and replaces that with the
current PTP time. This changes the intended effective base-time of the
schedule, which will in the end have a different phase offset than if
the base-time of 0.000000000 was to be advanced by an integer multiple
of the cycle-time.
Fixes: 34c6adf1977b ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dpaa2 driver depends on devlink, so it should select
NET_DEVLINK in order to fix compile errors, such as:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.o: in function `dpaa2_eth_rx_err':
dpaa2-eth.c:(.text+0x3cec): undefined reference to `devlink_trap_report'
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth-devlink.o: in function `dpaa2_eth_dl_info_get':
dpaa2-eth-devlink.c:(.text+0x160): undefined reference to `devlink_info_driver_name_put'
Fixes: ceeb03ad8e22 ("dpaa2-eth: add basic devlink support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123163553.1666476-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove usage of magic numbers.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Explicitly enable the FSL_XGMAC_MDIO Kconfig option in order to have
MDIO access to internal and external PHYs.
Fixes: 719479230893 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201119145106.712761-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the control buffer descriptor (cbd) fields have endianness
restrictions while the commands passed into the control buffers
don't (with one exception). This patch fixes offending code,
by adding endianness accessors for cbd fields and removing the
unnecessary ones in case of data buffer fields. Currently there's
no need to convert all commands to little endian format, the patch
only focuses on fixing current endianness issues reported by sparse.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These particular fields are specified in the H/W reference
manual as having network byte order format, so enforce big
endian annotation for them and clear the related sparse
warnings in the process.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to a hardware issue, an access to MDIO registers
that is concurrent with other ENETC register accesses
may lead to the MDIO access being dropped or corrupted.
The workaround introduces locking for all register accesses
to the ENETC register space. To reduce performance impact,
a readers-writers locking scheme has been implemented.
The writer in this case is the MDIO access code (irrelevant
whether that MDIO access is a register read or write), and
the reader is any access code to non-MDIO ENETC registers.
Also, the datapath functions acquire the read lock fewer times
and use _hot accessors. All the rest of the code uses the _wa
accessors which lock every register access.
The commit introducing MDIO support is -
commit ebfcb23d62ab ("enetc: Add ENETC PF level external MDIO support")
but due to subsequent refactoring this patch is applicable on
top of a later commit.
Fixes: 6517798dd343 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201112182608.26177-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc3, including fixes from wireless, can, and
netfilter subtrees.
Current merge window - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous releases - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even if
inner packet has IP_DF (don't fragment) set in its header (when
TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break gso
support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous releases - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need to
be dropped
- always clone the skbs to make sure they have a reference on the
socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200"
* tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
ionic: check port ptr before use
r8169: work around short packet hw bug on RTL8125
net: openvswitch: silence suspicious RCU usage warning
chelsio/chtls: fix always leaking ctrl_skb
chelsio/chtls: fix memory leaks caused by a race
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
...
|
|
Tx checksumming has been defeatured and completely removed
from the h/w reference manual. Made a little cleanup for the
TSE case as this is complementary code.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201103140213.3294-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix coccicheck warnings:
./dpaa_eth.c:2549:2-22: WARNING: Assignment of 0/1 to bool variable
./dpaa_eth.c:2562:2-22: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://lore.kernel.org/r/1604405100-33255-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver uses in_irq() + in_serving_softirq() magic to decide if NAPI
scheduling is required or packet processing.
The usage of in_*() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context.
Use the `sched_napi' argument passed by the callback. It is set true if
called from the interrupt handler and NAPI should be scheduled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
|
|
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:
- Hard interrupt context
- Any context which is not serving soft interrupts
Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:
/*
* In case of threaded ISR, for RT kernels in_irq() does not return
* appropriate value, so use in_serving_softirq to distinguish between
* softirq and irq contexts.
*/
if (in_irq() || !in_serving_softirq())
This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.
The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.
The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.
The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
portal_isr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
Both need to schedule NAPI.
The crypto part has another code path leading up to this:
kill_fq()
empty_retired_fq()
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.
The code path:
caam_qi_poll() -> qman_p_poll_dqrr()
is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.
Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
|
|
The headroom reserved for received frames needs to be aligned to an
RX specific value. There is currently a discrepancy between the values
used in the Ethernet driver and the values passed to the FMan.
Coincidentally, the resulting aligned values are identical.
Fixes: 3c68b8fffb48 ("dpaa_eth: FMan erratum A050385 workaround")
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Impose a larger RX private data area only when the A050385 erratum is
present on the hardware. A smaller buffer size is sufficient in all
other scenarios. This enables a wider range of linear Jumbo frame
sizes in non-erratum scenarios, instead of turning to multi
buffer Scatter/Gather frames. The maximum linear frame size is
increased by 128 bytes for non-erratum arm64 platforms.
Cleanup the hardware annotations header defines in the process.
Fixes: 3c68b8fffb48 ("dpaa_eth: FMan erratum A050385 workaround")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull more flexible-array member conversions from Gustavo A. R. Silva:
"Replace zero-length arrays with flexible-array members"
* tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
printk: ringbuffer: Replace zero-length array with flexible-array member
net/smc: Replace zero-length array with flexible-array member
net/mlx5: Replace zero-length array with flexible-array member
mei: hw: Replace zero-length array with flexible-array member
gve: Replace zero-length array with flexible-array member
Bluetooth: btintel: Replace zero-length array with flexible-array member
scsi: target: tcmu: Replace zero-length array with flexible-array member
ima: Replace zero-length array with flexible-array member
enetc: Replace zero-length array with flexible-array member
fs: Replace zero-length array with flexible-array member
Bluetooth: Replace zero-length array with flexible-array member
params: Replace zero-length array with flexible-array member
tracepoint: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_proto: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_commands: Replace zero-length array with flexible-array member
mailbox: zynqmp-ipi-message: Replace zero-length array with flexible-array member
dmaengine: ti-cppi5: Replace zero-length array with flexible-array member
|
|
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on the second option,
using skb_realloc_headroom() to create a new skb to accommodate
PTP frames. Turns out that this method is not reliable, as
reallocation of skbs for PTP frames along with the required
overhead (skb_set_owner_w, consume_skb) is causing random
crashes in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time on the same device
(as seen in James' report).
Note that these crashes don't occur with a single TCP stream,
nor with multiple concurrent UDP streams, but only when multiple
TCP streams are run concurrently with the PTP packet flow
(doing skb reallocation).
This patch enforces the first method, by requesting enough
headroom from the stack to accommodate PTP frames, and so avoiding
skb_realloc_headroom() & co, and the crashes no longer occur.
There's no reason not to set needed_headroom to a large enough
value to accommodate PTP frames, so in this regard this patch
is a fix.
Reported-by: James Jurack <james.jurack@ametek.com>
Fixes: bee9e58c9e98 ("gianfar:don't add FCB length to hard_header_len")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201020173605.1173-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on skb_realloc_headroom()
to create new skbs to accommodate PTP frames. Turns out that
this method is not reliable in this context at least, as
skb_realloc_headroom() for PTP frames can cause random crashes,
mostly in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time with the PTP flow
on the same device (as seen in James' report). I also noticed
that when the system is loaded by sending multiple TCP streams,
the driver receives cloned skbs in large numbers.
skb_cow_head() instead proves to be stable in this scenario,
and not only handles cloned skbs too but it's also more efficient
and widely used in other drivers.
The commit introducing skb_realloc_headroom in the driver
goes back to 2009, commit 93c1285c5d92
("gianfar: reallocate skb when headroom is not enough for fcb").
For practical purposes I'm referencing a newer commit (from 2012)
that brings the code to its current structure (and fixes the PTP
case).
Fixes: 9c4886e5e63b ("gianfar: Fix invalid TX frames returned on error queue when time stamping")
Reported-by: James Jurack <james.jurack@ametek.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201029081057.8506-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some (apparently older) versions of the FEC hardware block do not like
the MMFR register being cleared to avoid generation of MII events at
initialization time. The action of clearing this register results in no
future MII events being generated at all on the problem block. This means
the probing of the MDIO bus will find no PHYs.
Create a quirk that can be checked at the FECs MII init time so that
the right thing is done. The quirk is set as appropriate for the FEC
hardware blocks that are known to need this.
Fixes: f166f890c8f0 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Fugang Duan <fugand.duan@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Link: https://lore.kernel.org/r/20201028052232.1315167-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Clang warns about the extra parentheses in this comparison:
drivers/net/ethernet/freescale/ucc_geth.c:1361:28:
warning: equality comparison with extraneous parentheses
if ((ugeth->phy_interface == PHY_INTERFACE_MODE_SGMII))
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
It seems clear the intent here is to do a comparison not an
assignment, so drop the extra parentheses to avoid any confusion.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201023033236.3296988-1-mpe@ellerman.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04e3 ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed |
