summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/freescale
AgeCommit message (Collapse)Author
2020-02-18net: fec: Prevent unbind operationFabio Estevam
After performing an unbind/bind operation the network is no longer functional on i.MX6 (which has a single FEC instance): # echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind # echo 2188000.ethernet > /sys/bus/platform/drivers/fec/bind [ 10.756519] pps pps0: new PPS source ptp0 [ 10.792626] libphy: fec_enet_mii_bus: probed [ 10.799330] fec 2188000.ethernet eth0: registered PHC device 1 # udhcpc -i eth0 udhcpc: started, v1.31.1 [ 14.985211] fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch [ 14.993140] libphy: PHY fixed-0:00 not found [ 14.997643] fec 2188000.ethernet eth0: could not attach to PHY On SoCs with two FEC instances there are some cases where one FEC instance depends on the other one being present. One such example is i.MX28, which has the following FEC dependency as noted in the comments: /* * The i.MX28 dual fec interfaces are not equal. * Here are the differences: * * - fec0 supports MII & RMII modes while fec1 only supports RMII * - fec0 acts as the 1588 time master while fec1 is slave * - external phys can only be configured by fec0 * * That is to say fec1 can not work independently. It only works * when fec0 is working. The reason behind this design is that the * second interface is added primarily for Switch mode. * * Because of the last point above, both phys are attached on fec0 * mdio interface in board design, and need to be configured by * fec0 mii_bus. */ Prevent the unbind operation to avoid these issues. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris. 2) Fix thermal zone registration in iwlwifi, from Andrei Otcheretianski. 3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer. 4) Use after free in mptcp, from Florian Westphal. 5) Use after free in wireguard's root_remove_peer_lists, from Eric Dumazet. 6) Properly access packets heads in bonding alb code, from Eric Dumazet. 7) Fix data race in skb_queue_len(), from Qian Cai. 8) Fix regression in r8169 on some chips, from Heiner Kallweit. 9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang. 10) Certain kinds of set link netlink operations can cause a NULL deref in the ipv6 addrconf code. Fix from Eric Dumazet. 11) Don't cancel uninitialized work queue in drop monitor, from Ido Schimmel. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits) net: thunderx: use proper interface type for RGMII mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap bpf: Improve bucket_log calculation logic selftests/bpf: Test freeing sockmap/sockhash with a socket in it bpf, sockhash: Synchronize_rcu before free'ing map bpf, sockmap: Don't sleep while holding RCU lock on tear-down bpftool: Don't crash on missing xlated program instructions bpf, sockmap: Check update requirements after locking drop_monitor: Do not cancel uninitialized work item mlxsw: spectrum_dpipe: Add missing error path mlxsw: core: Add validation of hardware device types for MGPIR register mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort selftests: mlxsw: Add test cases for local table route replacement mlxsw: spectrum_router: Prevent incorrect replacement of local table routes net: dsa: microchip: enable module autoprobe ipv6/addrconf: fix potential NULL deref in inet6_set_link_af() dpaa_eth: support all modes with rate adapting PHYs net: stmmac: update pci platform data to use phy_interface net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter ...
2020-02-08Merge tag 'armsoc-drivers' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC-related driver updates from Olof Johansson: "Various driver updates for platforms: - Nvidia: Fuse support for Tegra194, continued memory controller pieces for Tegra30 - NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC - NXP/FSL: i.MX8MP SoC driver pieces - TI Keystone: ring accelerator driver - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs. - Xilinx ZynqMP: feature checking interface for firmware. Mailbox communication for power management - Overall support patch set for cpuidle on more complex hierarchies (PSCI-based) and misc cleanups, refactorings of Marvell, TI, other platforms" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits) drivers: soc: xilinx: Use mailbox IPI callback dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists MAINTAINERS: Add brcmstb PCIe controller entry soc/tegra: fuse: Unmap registers once they are not needed anymore soc/tegra: fuse: Correct straps' address for older Tegra124 device trees soc/tegra: fuse: Warn if straps are not ready soc/tegra: fuse: Cache values of straps and Chip ID registers memory: tegra30-emc: Correct error message for timed out auto calibration memory: tegra30-emc: Firm up hardware programming sequence memory: tegra30-emc: Firm up suspend/resume sequence soc/tegra: regulators: Do nothing if voltage is unchanged memory: tegra: Correct reset value of xusb_hostr soc/tegra: fuse: Add APB DMA dependency for Tegra20 bus: tegra-aconnect: Remove PM_CLK dependency dt-bindings: mediatek: add MT6765 power dt-bindings soc: mediatek: cmdq: delete not used define memory: tegra: Add support for the Tegra194 memory controller memory: tegra: Only include support for enabled SoCs memory: tegra: Support DVFS on Tegra186 and later ...
2020-02-07dpaa_eth: support all modes with rate adapting PHYsMadalin Bucur
Stop removing modes that are not supported on the system interface when the connected PHY is capable of rate adaptation. This addresses an issue with the LS1046ARDB board 10G interface no longer working with an 1G link partner after autonegotiation support was added for the Aquantia PHY on board in commit 09c4c57f7bc4 ("net: phy: aquantia: add support for auto-negotiation configuration") Before this commit the values advertised by the PHY were not influenced by the dpaa_eth driver removal of system-side unsupported modes as the aqr_config_aneg() was basically a no-op. After this commit, the modes removed by the dpaa_eth driver were no longer advertised thus autonegotiation with 1G link partners failed. Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de> Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Minor conflict in mlx5 because changes happened to code that has moved meanwhile. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23net: fsl/fman: rename IF_MODE_XGMII to IF_MODE_10GMadalin Bucur
As the only 10G PHY interface type defined at the moment the code was developed was XGMII, although the PHY interface mode used was not XGMII, XGMII was used in the code to denote 10G. This patch renames the 10G interface mode to remove the ambiguity. Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23net/fsl: treat fsl,erratum-a011043Madalin Bucur
When fsl,erratum-a011043 is set, adjust for erratum A011043: MDIO reads to internal PCS registers may result in having the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no error and read data (MDIO_DATA[MDIO_DATA]) is correct. Software may get false read error when reading internal PCS registers through MDIO. As a workaround, all internal MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit. Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-23net: convert suitable drivers to use phy_do_ioctl_runningHeiner Kallweit
Convert suitable drivers to use new helper phy_do_ioctl_running. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Timur Tabi <timur@kernel.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: convert suitable network drivers to use phy_do_ioctlHeiner Kallweit
Convert suitable network drivers to use phy_do_ioctl. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-17enetc: Don't print from enetc_sched_speed_set when link goes downVladimir Oltean
It is not an error to unplug a cable from the ENETC port even with TSN offloads, so don't spam the log with link-related messages from the tc-taprio offload subsystem, a single notification is sufficient: [10972.351859] fsl_enetc 0000:00:00.0 eno0: Qbv PSPEED set speed link down. [10972.360241] fsl_enetc 0000:00:00.0 eno0: Link is Down Fixes: 2e47cb415f0a ("enetc: update TSN Qbv PSPEED set according to adjust link speed") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-16Merge tag 'soc-fsl-next-v5.6' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers NXP/FSL SoC driver updates for v5.6 QUICC Engine drivers - Improve the QE drivers to be compatible with ARM/ARM64/PPC64 architectures - Various cleanups to the QE drivers * tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux: (49 commits) soc: fsl: qe: remove set but not used variable 'mm_gc' soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32 net/wan/fsl_ucc_hdlc: reject muram offsets above 64K net/wan/fsl_ucc_hdlc: fix reading of __be16 registers net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE() soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c soc: fsl: qe: drop pointless check in qe_sdma_init() soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init() soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path soc: fsl: qe: drop broken lazy call of cpm_muram_init() soc: fsl: qe: make cpm_muram_free() ignore a negative offset soc: fsl: qe: make cpm_muram_free() return void soc: fsl: qe: change return type of cpm_muram_alloc() to s32 serial: ucc_uart: access __be32 field using be32_to_cpu serial: ucc_uart: limit brg-frequency workaround to PPC32 serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe() serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32 ... Link: https://lore.kernel.org/r/1578608351-23289-1-git-send-email-leoyang.li@nxp.com Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
The ungrafting from PRIO bug fixes in net, when merged into net-next, merge cleanly but create a build failure. The resolution used here is from Petr Machata. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-08net: dsa: felix: fix link errorArnd Bergmann
When the enetc driver is disabled, the mdio support fails to get built: drivers/net/dsa/ocelot/felix_vsc9959.o: In function `vsc9959_mdio_bus_alloc': felix_vsc9959.c:(.text+0x19c): undefined reference to `enetc_hw_alloc' felix_vsc9959.c:(.text+0x1d1): undefined reference to `enetc_mdio_read' felix_vsc9959.c:(.text+0x1d8): undefined reference to `enetc_mdio_write' Change the Makefile to enter the subdirectory for this as well. Fixes: bdeced75b13f ("net: dsa: felix: Add PCS operations for PHYLINK") Fixes: 6517798dd343 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-07enetc: Fix inconsistent IS_ERR and PTR_ERRYueHaibing
The proper pointer to be passed as argument is hw Detected using Coccinelle. Fixes: 6517798dd343 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-07enetc: Fix an off by one in enetc_setup_tc_txtime()Dan Carpenter
The priv->tx_ring[] has 16 elements but only priv->num_tx_rings are set up, the rest are NULL. This ">" comparison should be ">=" to avoid a potential crash. Fixes: 0d08c9ec7d6e ("enetc: add support time specific departure base on the qos etf") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-05enetc: Set MDIO_CFG_HOLD to the recommended value of 2Vladimir Oltean
This increases the MDIO hold time to 5 enet_clk cycles from the previous value of 0. This is actually the out-of-reset value, that the driver was previously overwriting with 0. Zero worked for the external MDIO, but breaks communication with the internal MDIO buses on which the PCS of ENETC SI's and Felix switch are found. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-05enetc: Make MDIO accessors more generic and export to include/linux/fslClaudiu Manoil
Within the LS1028A SoC, the register map for the ENETC MDIO controller is instantiated a few times: for the central (external) MDIO controller, for the internal bus of each standalone ENETC port, and for the internal bus of the Felix switch. Refactoring is needed to support multiple MDIO buses from multiple drivers. The enetc_hw structure is made an opaque type and a smaller enetc_mdio_priv is created. 'mdio_base' - MDIO registers base address - is being parameterized, to be able to work with different MDIO register bases. The ENETC MDIO bus operations are exported from the fsl-enetc-mdio kernel object, the same that registers the central MDIO controller (the dedicated PF). The ENETC main driver has been changed to select it, and use its exported helpers to further register its private MDIO bus. The DSA Felix driver will do the same. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-02net: freescale: fec: Fix ethtool -d runtime PMAndrew Lunn
In order to dump the FECs registers the clocks have to be ticking, otherwise a data abort occurs. Add calls to runtime PM so they are enabled and later disabled. Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save power") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-02enetc: add support time specific departure base on the qos etfPo Liu
ENETC implement time specific departure capability, which enables the user to specify when a frame can be transmitted. When this capability is enabled, the device will delay the transmission of the frame so that it can be transmitted at the precisely specified time. The delay departure time up to 0.5 seconds in the future. If the departure time in the transmit BD has not yet been reached, based on the current time, the packet will not be transmitted. This driver was loaded by Qos driver ETF. User could load it by tc commands. Here are the example commands: tc qdisc add dev eth0 root handle 1: mqprio \ num_tc 8 map 0 1 2 3 4 5 6 7 hw 1 tc qdisc replace dev eth0 parent 1:8 etf \ clockid CLOCK_TAI delta 30000 offload These example try to set queue mapping first and then set queue 7 with 30us ahead dequeue time. Then user send test frame should set SO_TXTIME feature for socket. There are also some limitations for this feature in hardware: - Transmit checksum offloads and time specific departure operation are mutually exclusive. - Time Aware Shaper feature (Qbv) offload and time specific departure operation are mutually exclusive. Signed-off-by: Po Liu <Po.Liu@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-02fsl/fman: use resource_sizeJulia Lawall
Use resource_size rather than a verbose computation on the end and start fields. The semantic patch that makes these changes is as follows: (http://coccinelle.lip6.fr/) <smpl> @@ struct resource ptr; @@ - (ptr.end + 1 - ptr.start) + resource_size(&ptr) @@ struct resource *ptr; @@ - (ptr->end + 1 - ptr->start) + resource_size(ptr) </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Simple overlapping changes in bpf land wrt. bpf_helper_defs.h handling. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-28gianfar: Fix TX timestamping with a stacked DSA driverVladimir Oltean
The driver wrongly assumes that it is the only entity that can set the SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the gfar_clean_tx_ring function, where the TX timestamp is collected if necessary, the aforementioned bit is used to discriminate whether or not the TX timestamp should be delivered to the socket's error queue. But a stacked driver such as a DSA switch can also set the SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in order to denote that the hardware timestamping process is undergoing. Therefore, gianfar would misinterpret the "in progress" bit as being its own, and deliver a second skb clone in the socket's error queue, completely throwing off a PTP process which is not expecting to receive it, _even though_ TX timestamping is not enabled for gianfar. There have been discussions [0] as to whether non-MAC drivers need or not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2 timestamps, a sw and a hw one, to applications which only expect one). But as of this patch, there are at least 2 PTP drivers that would break in conjunction with gianfar: the sja1105 DSA switch and the felix switch, by way of its ocelot core driver. So regardless of that conclusion, fix the gianfar driver to not do stuff based on flags set by others and not intended for it. [0]: https://www.spinics.net/lists/netdev/msg619699.html Fixes: f0ee7acfcdd4 ("gianfar: Add hardware TX timestamping support") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26dpaa_eth: fix DMA mapping leakMadalin Bucur
On the error path some fragments remain DMA mapped. Adding a fix that unmaps all the fragments. Rework cleanup path to be simpler. Fixes: 8151ee88bad5 ("dpaa_eth: use page backed rx buffers") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Mere overlapping changes in the conflicts here. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-17dpaa2-ptp: fix double free of the ptp_qoriq IRQIoana Ciornei
Upon reusing the ptp_qoriq driver, the ptp_qoriq_free() function was used on the remove path to free any allocated resources. The ptp_qoriq IRQ is among these resources that are freed in ptp_qoriq_free() even though it is also a managed one (allocated using devm_request_threaded_irq). Drop the resource managed version of requesting the IRQ in order to not trigger a double free of the interrupt as below: [ 226.731005] Trying to free already-free IRQ 126 [ 226.735533] WARNING: CPU: 6 PID: 749 at kernel/irq/manage.c:1707 __free_irq+0x9c/0x2b8 [ 226.743435] Modules linked in: [ 226.746480] CPU: 6 PID: 749 Comm: bash Tainted: G W 5.4.0-03629-gfd7102c32b2c-dirty #912 [ 226.755857] Hardware name: NXP Layerscape LX2160ARDB (DT) [ 226.761244] pstate: 40000085 (nZcv daIf -PAN -UAO) [ 226.766022] pc : __free_irq+0x9c/0x2b8 [ 226.769758] lr : __free_irq+0x9c/0x2b8 [ 226.773493] sp : ffff8000125039f0 (...) [ 226.856275] Call trace: [ 226.858710] __free_irq+0x9c/0x2b8 [ 226.862098] free_irq+0x30/0x70 [ 226.865229] devm_irq_release+0x14/0x20 [ 226.869054] release_nodes+0x1b0/0x220 [ 226.872790] devres_release_all+0x34/0x50 [ 226.876790] device_release_driver_internal+0x100/0x1c0 Fixes: d346c9e86d86 ("dpaa2-ptp: reuse ptp_qoriq driver") Cc: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-16dpaa2-ptp: add external trigger event supportYangbo Lu
This patch is to add external trigger event support for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12netdev: pass the stuck queue to the timeout handlerMichael S. Tsirkin
This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-10enetc: remove variable 'tc_max_sized_frame' set but not usedChen Wandun
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs: drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable] Fixes: c431047c4efe ("enetc: add support Credit Based Shaper(CBS) for hardware offload") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-10enetc: add software timestampingMichael Walle
Provide a software TX timestamp and add it to the ethtool query interface. skb_tx_timestamp() is also needed if one would like to use PHY timestamping. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-09net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32Rasmus Villemoes
Currently, QUICC_ENGINE depends on PPC32, so this in itself does not change anything. In order to allow removing the PPC32 dependency from QUICC_ENGINE and avoid allmodconfig build failures, add this explicit dependency. Also, the QE Ethernet has never been integrated on any non-PowerPC SoC and most likely will not be in the future. Reviewed-by: Timur Tabi <timur@kernel.org> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Li Yang <leoyang.li@nxp.com>
2019-12-06enetc: disable EEE autoneg by defaultYangbo Lu
The EEE support has not been enabled on ENETC, but it may connect to a PHY which supports EEE and advertises EEE by default, while its link partner also advertises EEE. If this happens, the PHY enters low power mode when the traffic rate is low and causes packet loss. This patch disables EEE advertisement by default for any PHY that ENETC connects to, to prevent the above unwanted outcome. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-25enetc: add support Credit Based Shaper(CBS) for hardware offloadPo Liu
The ENETC hardware support the Credit Based Shaper(CBS) which part of the IEEE-802.1Qav. The CBS driver was loaded by the sch_cbs interface when set in the QOS in the kernel. Here is an example command to set 20Mbits bandwidth in 1Gbits port for taffic class 7: tc qdisc add dev eth0 root handle 1: mqprio \ num_tc 8 map 0 1 2 3 4 5 6 7 hw 1 tc qdisc replace dev eth0 parent 1:8 cbs \ locredit -1470 hicredit 30 \ sendslope -980000 idleslope 20000 offload 1 Signed-off-by: Po Liu <Po.Liu@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock from commit c8183f548902 ("s390/qeth: fix potential deadlock on workqueue flush"), removed the code which was removed by commit 9897d583b015 ("s390/qeth: consolidate some duplicated HW cmd code"). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-11-21enetc: make enetc_setup_tc_mqprio staticMao Wenan
While using ARCH=mips CROSS_COMPILE=mips-linux-gnu- command to compile, make C=2 drivers/net/ethernet/freescale/enetc/enetc.o one warning can be found: drivers/net/ethernet/freescale/enetc/enetc.c:1439:5: warning: symbol 'enetc_setup_tc_mqprio' was not declared. Should it be static? This patch make symbol enetc_setup_tc_mqprio static. Fixes: 34c6adf1977b ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-21drivers: net: Fix Kconfig indentation, continuedKrzysztof Kozlowski
Adjust indentation from spaces to tab (+optional two spaces) as in coding style. This fixes various indentation mixups (seven spaces, tab+one space, etc). Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller
Daniel Borkmann says: ==================== pull-request: bpf-next 2019-11-20 The following pull-request contains BPF updates for your *net-next* tree. We've added 81 non-merge commits during the last 17 day(s) which contain a total of 120 files changed, 4958 insertions(+), 1081 deletions(-). There are 3 trivial conflicts, resolve it by always taking the chunk from 196e8ca74886c433: <<<<<<< HEAD ======= void *bpf_map_area_mmapable_alloc(u64 size, int numa_node); >>>>>>> 196e8ca74886c433dcfc64a809707074b936aaf5 <<<<<<< HEAD void *bpf_map_area_alloc(u64 size, int numa_node) ======= static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable) >>>>>>> 196e8ca74886c433dcfc64a809707074b936aaf5 <<<<<<< HEAD if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) { ======= /* kmalloc()'ed memory can't be mmap()'ed */ if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) { >>>>>>> 196e8ca74886c433dcfc64a809707074b936aaf5 The main changes are: 1) Addition of BPF trampoline which works as a bridge between kernel functions, BPF programs and other BPF programs along with two new use cases: i) fentry/fexit BPF programs for tracing with practically zero overhead to call into BPF (as opposed to k[ret]probes) and ii) attachment of the former to networking related programs to see input/output of networking programs (covering xdpdump use case), from Alexei Starovoitov. 2) BPF array map mmap support and use in libbpf for global data maps; also a big batch of libbpf improvements, among others, support for reading bitfields in a relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko. 3) Extend s390x JIT with usage of relative long jumps and loads in order to lift the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich. 4) Add BPF audit support and emit messages upon successful prog load and unload in order to have a timeline of events, from Daniel Borkmann and Jiri Olsa. 5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode (XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson. 6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API call named bpf_get_link_xdp_info() for retrieving the full set of prog IDs attached to XDP, from Toke Høiland-Jørgensen. 7) Add BTF support for array of int, array of struct and multidimensional arrays and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau. 8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo. 9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid xdping to be run as standalone, from Jiri Benc. 10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song. 11) Fix a memory leak in BPF fentry test run data, from Colin Ian King. 12) Various smaller misc cleanups and improvements mostly all over BPF selftests and samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19net: fec: fix clock count mis-matchChuhong Yuan
pm_runtime_put_autosuspend in probe will call runtime suspend to disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM is not defined, its implementation will be empty, then runtime suspend will not be called.) Therefore, we can call pm_runtime_get_sync to runtime resume it first to enable clks, which matches the runtime suspend. (Only when CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be empty,