| Age | Commit message (Collapse) | Author |
|---|
|
The 6220 and 6250 switches do not have a learn2all bit in global1, ATU
control register; bit 3 is reserverd.
On the switches that do have that bit, it is used to control whether
learning frames are sent out the ports that have the message_port bit
set. So rather than adding yet another chip method, use the existence
of the ->port_setup_message_port method as a proxy for determining
whether the learn2all bit exists (and should be set).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201210110645.27765-1-rasmus.villemoes@prevas.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the underlying read operation failed we would end up writing stale
data to the supplied buffer. This would end up with the last
successfully read value repeating. Fix this by only writing the data
when we know the read was good. This will mean that failed values will
return 0xffff.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MV88E6097 presents the serdes interrupts for ports 8 and 9 via the
Switch Global 2 registers. There is no additional layer of
enablinh/disabling the serdes interrupts like other mv88e6xxx switches.
Even though most of the serdes behaviour is the same as the MV88E6185
that chip does not provide interrupts for serdes events so unlike
earlier commits the functions added here are specific to the MV88E6097.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement serdes_power, serdes_get_lane and serdes_pcs_get_state ops for
the MV88E6097/6095/6185 so that ports 8 & 9 can be supported as serdes
ports and directly connected to other network interfaces or to SFPs
without a PHY.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a port is configured with 'managed = "in-band-status"' switch chips
like the 88E6390 need to propagate the SERDES link state to the MAC
because the link state is not correctly detected. This causes problems
on the 88E6185/88E6097 where the link partner won't see link state
changes because we're forcing the link.
To address this introduce a new device specific op port_sync_link() and
push the logic from mv88e6xxx_mac_link_up() into that. Provide an
implementation for the 88E6185 like devices which doesn't force the
link.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f01 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Most of the other chip info constants have helpers to get at them; add
one for max_vid to keep things consistent.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201110185720.18228-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When mv88e6xxx_fid_map return error, we lost free the table.
Fix it.
Fixes: bfb255428966 ("net: dsa: mv88e6xxx: Add devlink regions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhangxiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201109144416.1540867-1-zhangxiaoxu5@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Export the raw VTU data and related registers in a devlink region so
that it can be inspected from userspace and compared to the current
bridge configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201109082927.8684-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA assumes that a bridge which has vlan filtering disabled is not
vlan aware, and ignores all vlan configuration. However, the kernel
software bridge code allows configuration in this state.
This causes the kernel's idea of the bridge vlan state and the
hardware state to disagree, so "bridge vlan show" indicates a correct
configuration but the hardware lacks all configuration. Even worse,
enabling vlan filtering on a DSA bridge immediately blocks all traffic
which, given the output of "bridge vlan show", is very confusing.
Allow the VLAN configuration to be updated on Marvell DSA bridges,
otherwise we end up cutting all traffic when enabling vlan filtering.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1kYAU3-00071C-1G@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a devlink region to return the per port registers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return the driver name and the asic.id with the switch name.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the global registers, and the ATU to be snapshot via devlink
regions. It is later planned to add support for the port registers.
v2:
Remove left over debug prints
Comment ATU format is generic for mv88e6xxx, not wider
v3:
Make use of ops structure passed to snapshot function
Remove port regions
v4:
Make use of enum mv88e6xxx_region_id
Fix global2/global1 read typ0
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor the code in mv88e6xxx_atu_new() which builds a bitmaps of
FIDs in use into a helper function. This will be reused by the devlink
code when dumping the ATU.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There will soon be more devlink code. Move the existing code into a
file of its own, before we start adding this new code.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444a4 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When building on platforms without device tree, e.g. amd64, W=1 gives
a warning about mv88e6xxx_mdio_external_match being unused. Replace
of_match_node() with of_device_is_compatible() to prevent this
warning.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the chips in the mv88e6xxx family don't support jumbo
configuration per port. But they do have a chip-wide max frame size that
can be used. Use this to approximate the behaviour of configuring a port
based MTU.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6190 and MV88E6190X both support per port jumbo configuration
just like the other GE switches. Install the appropriate ops.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6097 chip does not support configuring jumbo frames. Prior to
commit 5f4366660d65 only the 6352, 6351, 6165 and 6320 chips configured
jumbo mode. The refactor accidentally added the function for the 6097.
Remove the erroneous function pointer assignment.
Fixes: 5f4366660d65 ("net: dsa: mv88e6xxx: Refactor setting of jumbo frames")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If in-band negotiation or fixed-link modes are specified for a DSA
port, the DSA code will force the link down during initialisation. For
fixed-link mode, this is fine, as phylink will manage the link state.
However, for in-band mode, phylink expects the PCS to detect link,
which will not happen if the link is forced down.
There is a related issue that in in-band mode, the link could come up
while we are making configuration changes, so we should force the link
down prior to reconfiguring the interface mode.
This patch addresses both issues.
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell Switches support jumbo packages. So implement the
callbacks needed for changing the MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct parameters and add the missing ones.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't act on any errors reading registers while handling watchdog
interrupt. Since this is an interrupt handler, we cannot return such
errors. So just remove the variable.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow spec member vlan_tci is in network order. Hence comparisons
should be made again network order values.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Oddly, GENMASK() requires signed bit numbers, so that it can compare
them for < 0. If passed an unsigned type, we get warnings about the
test never being true.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts were all overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for reading and reporting the 10G link status on the
88e6390 in addition to the 1000BASE-X/2500BASE-X/SGMII status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private MV88E6390_PCS_CONTROL_1 definitions in serdes.h reflects
the IEEE 802.3 standard PCS control register 1 definitions, only
offset by 0x1000 in the PHYXS register space. Rather than inventing
our own, use those that already exist, and name the register
MV88E6390_10G_CTRL1.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d1cbfd771ce8 ("ptp_clock: Allow for it to be optional") changed
all PTP-capable Ethernet drivers from `select PTP_1588_CLOCK` to `imply
PTP_1588_CLOCK`, "in order to break the hard dependency between the PTP
clock subsystem and ethernet drivers capable of being clock providers."
As a result it is possible to build PTP-capable Ethernet drivers without
the PTP subsystem by deselecting PTP_1588_CLOCK. Drivers are required to
handle the missing dependency gracefully.
Some PTP-capable Ethernet drivers (e.g., TI_CPSW) factor their PTP code
out into separate drivers (e.g., TI_CPTS_MOD). The above commit also
changed these PTP-specific drivers to `imply PTP_1588_CLOCK`, making it
possible to build them without the PTP subsystem. But as Grygorii
Strashko noted in [1]:
On Wed, Apr 22, 2020 at 02:16:11PM +0300, Grygorii Strashko wrote:
> Another question is that CPTS completely nonfunctional in this case and
> it was never expected that somebody will even try to use/run such
> configuration (except for random build purposes).
In my view, enabling a PTP-specific driver without the PTP subsystem is
a configuration error made possible by the above commit. Kconfig should
not allow users to create a configuration with missing dependencies that
results in "completely nonfunctional" drivers.
I audited all network drivers that call ptp_clock_register() but merely
`imply PTP_1588_CLOCK` and found five PTP-specific drivers that are
likely nonfunctional without PTP_1588_CLOCK:
NET_DSA_MV88E6XXX_PTP
NET_DSA_SJA1105_PTP
MACB_USE_HWSTAMP
CAVIUM_PTP
TI_CPTS_MOD
Note how these symbols all reference PTP or timestamping in their name;
this is a clue that they depend on PTP_1588_CLOCK.
Change them from `imply PTP_1588_CLOCK` [2] to `depends on PTP_1588_CLOCK`.
I'm not using `select PTP_1588_CLOCK` here because PTP_1588_CLOCK has
its own dependencies, which `select` would not transitively apply.
Additionally, remove the `select NET_PTP_CLASSIFY` from CPTS_TI_MOD;
PTP_1588_CLOCK already selects that.
[1]: https://lore.kernel.org/lkml/c04458ed-29ee-1797-3a11-7f3f560553e6@ti.com/
[2]: NET_DSA_SJA1105_PTP had never declared any type of dependency on
PTP_1588_CLOCK (`imply` or otherwise); adding a `depends on PTP_1588_CLOCK`
here seems appropriate.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d1cbfd771ce8 ("ptp_clock: Allow for it to be optional")
Signed-off-by: Clay McClure <clay@daemons.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These struct members named 'phylink_validate' was assigned twice:
static const struct mv88e6xxx_ops mv88e6190_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6190x_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390x_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6191_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6290_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
Remove all the first one and leave the second one which are been used in
fact. Be aware that for 'mv88e6190x_ops' the assignment functions is
different while the others are all the same. This fixes the following
coccicheck warning:
drivers/net/dsa/mv88e6xxx/chip.c:3911:48-49: phylink_validate: first
occurrence line 3965, second occurrence line 3967
drivers/net/dsa/mv88e6xxx/chip.c:3970:49-50: phylink_validate: first
occurrence line 4024, second occurrence line 4026
drivers/net/dsa/mv88e6xxx/chip.c:4029:48-49: phylink_validate: first
occurrence line 4082, second occurrence line 4085
drivers/net/dsa/mv88e6xxx/chip.c:4184:48-49: phylink_validate: first
occurrence line 4238, second occurrence line 4242
Fixes: 4262c38dc42e ("net: dsa: mv88e6xxx: Add SERDES stats counters to all 6390 family members")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.
Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.
Fixes: 30c4a5b0aad8 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the status of the PHY_DETECT bit to determine whether we need to
force the MAC settings in mac_link_up() and mac_link_down().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port_link_state method is only used by mv88e6xxx_port_setup_mac(),
which is now only called during port setup, rather than also being
called via phylink's mac_config method.
Remove this now unnecessary optimisation, which allows us to remove the
port_link_state methods as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting the speed independently of duplex makes little sense; the two
parameters result from negotiation or fixed setup, and may have inter-
dependencies. Moreover, they are always controlled via the same
register - having them split means we have to read-modify-write this
register twice.
Combine the two operations into a single port_set_speed_duplex()
operation. Not only is this more efficient, it reduces the size of the
code as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink_mac_change() is supposed to be called with a 'false' argument
if the link has gone down since it was last reported up; this is to
ensure that link events along with renegotiation events are always
correctly reported to userspace.
Read the BMSR once when we have an interrupt, and report the link
latched status to phylink via phylink_mac_change(). phylink will deal
automatically with re-reading the link state once it has processed the
link-down event.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the mv88e6xxx phylink implementation down to Serdes PHYs, which
handle the PCS layer of such links.
- Implement phylink PCS link state reading, so that we can provide
ethtool with the linkmodes and link speed in the expected manner.
Note: this will only be called for in-band negotiation, which is
only supported by the serdes interfaces.
- Implement phylink PCS configuration, so that the in-band AN and
advertisement can be configured.
- Implement phylink PCS negotiation restart, so that the in-band AN
can be restarted.
- Implement phylink PCS link up, so that when operating out-of-band,
the Serdes can be configured for the appropriate fixed speed mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only configure the interface settings in mac_config(), leaving the
speed and duplex settings to mac_link_up to deal with.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SGMII/1000base-X serdes register set is a clause 22 register set
offset at 0x2000 in the PHYXS device. Rather than inventing our own
defintions, use those that already exist, and name the register
MV88E6390_SGMII_BMCR. Also remove the unused MV88E6390_SGMII_STATUS
definitions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes, nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7dfbb ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
