Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
|
|
If CONFIG_INET is not set and CONFIG_NETDEVSIM=y.
Building drivers/net/netdevsim/fib.o will get the following error:
drivers/net/netdevsim/fib.o: In function `nsim_fib4_rt_hw_flags_set':
fib.c:(.text+0x12b): undefined reference to `fib_alias_hw_flags_set'
drivers/net/netdevsim/fib.o: In function `nsim_fib4_rt_destroy':
fib.c:(.text+0xb11): undefined reference to `free_fib_info'
Correct the Kconfig for netdevsim.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 48bb9eb47b270 ("netdevsim: fib: Add dummy implementation for FIB offload")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement dummy IPv4 and IPv6 FIB "offload" in the driver by storing
currently "programmed" routes in a hash table. Each route in the hash
table is marked with "trap" indication. The indication is cleared when
the route is replaced or when the netdevsim instance is deleted.
This will later allow us to test the route offload API on top of
netdevsim.
v2:
* Convert to new fib_alias_hw_flags_set() interface
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the driver now supports USB4 which is the standard going forward,
update the Kconfig entry to mention this and rename the entry from
CONFIG_THUNDERBOLT to CONFIG_USB4 instead to help people to find the
correct option if they want to enable USB4.
Also do the same for Thunderbolt network driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20191217123345.31850-6-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes the crypto selection submenu depenencies. Otherwise, we'd
wind up issuing warnings in which certain dependencies we also select
couldn't be satisfied. This condition was triggered by the addition of
the test suite autobuilder in the previous commit.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WireGuard is a layer 3 secure networking tunnel made specifically for
the kernel, that aims to be much simpler and easier to audit than IPsec.
Extensive documentation and description of the protocol and
considerations, along with formal proofs of the cryptography, are
available at:
* https://www.wireguard.com/
* https://www.wireguard.com/papers/wireguard.pdf
This commit implements WireGuard as a simple network device driver,
accessible in the usual RTNL way used by virtual network drivers. It
makes use of the udp_tunnel APIs, GRO, GSO, NAPI, and the usual set of
networking subsystem APIs. It has a somewhat novel multicore queueing
system designed for maximum throughput and minimal latency of encryption
operations, but it is implemented modestly using workqueues and NAPI.
Configuration is done via generic Netlink, and following a review from
the Netlink maintainer a year ago, several high profile userspace tools
have already implemented the API.
This commit also comes with several different tests, both in-kernel
tests and out-of-kernel tests based on network namespaces, taking profit
of the fact that sockets used by WireGuard intentionally stay in the
namespace the WireGuard interface was originally created, exactly like
the semantics of userspace tun devices. See wireguard.com/netns/ for
pictures and examples.
The source code is fairly short, but rather than combining everything
into a single file, WireGuard is developed as cleanly separable files,
making auditing and comprehension easier. Things are laid out as
follows:
* noise.[ch], cookie.[ch], messages.h: These implement the bulk of the
cryptographic aspects of the protocol, and are mostly data-only in
nature, taking in buffers of bytes and spitting out buffers of
bytes. They also handle reference counting for their various shared
pieces of data, like keys and key lists.
* ratelimiter.[ch]: Used as an integral part of cookie.[ch] for
ratelimiting certain types of cryptographic operations in accordance
with particular WireGuard semantics.
* allowedips.[ch], peerlookup.[ch]: The main lookup structures of
WireGuard, the former being trie-like with particular semantics, an
integral part of the design of the protocol, and the latter just
being nice helper functions around the various hashtables we use.
* device.[ch]: Implementation of functions for the netdevice and for
rtnl, responsible for maintaining the life of a given interface and
wiring it up to the rest of WireGuard.
* peer.[ch]: Each interface has a list of peers, with helper functions
available here for creation, destruction, and reference counting.
* socket.[ch]: Implementation of functions related to udp_socket and
the general set of kernel socket APIs, for sending and receiving
ciphertext UDP packets, and taking care of WireGuard-specific sticky
socket routing semantics for the automatic roaming.
* netlink.[ch]: Userspace API entry point for configuring WireGuard
peers and devices. The API has been implemented by several userspace
tools and network management utility, and the WireGuard project
distributes the basic wg(8) tool.
* queueing.[ch]: Shared function on the rx and tx path for handling
the various queues used in the multicore algorithms.
* send.c: Handles encrypting outgoing packets in parallel on
multiple cores, before sending them in order on a single core, via
workqueues and ring buffers. Also handles sending handshake and cookie
messages as part of the protocol, in parallel.
* receive.c: Handles decrypting incoming packets in parallel on
multiple cores, before passing them off in order to be ingested via
the rest of the networking subsystem with GRO via the typical NAPI
poll function. Also handles receiving handshake and cookie messages
as part of the protocol, in parallel.
* timers.[ch]: Uses the timer wheel to implement protocol particular
event timeouts, and gives a set of very simple event-driven entry
point functions for callers.
* main.c, version.h: Initialization and deinitialization of the module.
* selftest/*.h: Runtime unit tests for some of the most security
sensitive functions.
* tools/testing/selftests/wireguard/netns.sh: Aforementioned testing
script using network namespaces.
This commit aims to be as self-contained as possible, implementing
WireGuard as a standalone module not needing much special handling or
coordination from the network subsystem. I expect for future
optimizations to the network stack to positively improve WireGuard, and
vice-versa, but for the time being, this exists as intentionally
standalone.
We introduce a menu option for CONFIG_WIREGUARD, as well as providing a
verbose debug log and self-tests via CONFIG_WIREGUARD_DEBUG.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: David Miller <davem@davemloft.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some drivers are becoming more dependent on NET_DEVLINK being selected
in configuration. With upcoming compat functions, the behavior would be
wrong in case devlink was not compiled in. So make the drivers select
NET_DEVLINK and rely on the functions being there, not just stubs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to commit a7603ac1fc8c ("geneve: change NET_UDP_TUNNEL
dependency to select"), GTP has a dependency on NET_UDP_TUNNEL which
makes impossible to compile it if no other protocol depending on
NET_UDP_TUNNEL is selected.
Fix this by changing the depends to a select, and drop NET_IP_TUNNEL from
the select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Being able to build devlink as a module causes growing pains.
First all drivers had to add a meta dependency to make sure
they are not built in when devlink is built as a module. Now
we are struggling to invoke ethtool compat code reliably.
Make devlink code built-in, users can still not build it at
all but the dynamically loadable module option is removed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the kconfig warning in IPVLAN_L3S when neither INET nor IPV6
is enabled:
WARNING: unmet direct dependencies detected for NET_L3_MASTER_DEV
Depends on [n]: NET [=y] && (INET [=n] || IPV6 [=n])
Selected by [y]:
- IPVLAN_L3S [=y] && NETDEVICES [=y] && NET_CORE [=y] && NETFILTER [=y]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to the depends on NET_UDP_TUNNEL, at the moment it is impossible to
compile GENEVE if no other protocol depending on NET_UDP_TUNNEL is
selected.
Fix this changing the depends to a select, and drop NET_IP_TUNNEL from the
select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-and-tested-by: Andrea Claudi <aclaudi@redhat.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Right now ipvlan has a hard dependency on CONFIG_NETFILTER and
otherwise it cannot be built. However, the only ipvlan operation
mode that actually depends on netfilter is l3s, everything else
is independent of it. Break this hard dependency such that users
are able to use ipvlan l3 mode on systems where netfilter is not
compiled in.
Therefore, this adds a hidden CONFIG_IPVLAN_L3S bool which is
defaulting to y when CONFIG_NETFILTER is set in order to retain
existing behavior for l3s. All l3s related code is refactored
into ipvlan_l3s.c that is compiled in when enabled.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Martynas Pumputis <m@lambda.lt>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"also enables" should not be spelled as one word.
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/networking/ is full of cryptically named files with
driver documentation. This makes finding interesting information
at a glance really hard. Move all those files into a directory
called device_drivers (since not all drivers are for device) and
fix up references.
RFC v0.1 -> RFC v1:
- also add .txt suffix to the files which are missing it (Quentin)
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Henrik Austad <henrik@austad.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables virtio_net to switch over to a VF datapath when STANDBY
feature is enabled and a VF netdev is present with the same MAC address.
It allows live migration of a VM with a direct attached VF without the need
to setup a bond/team between a VF and virtio net device in the guest.
It uses the API that is exported by the net_failover driver to create and
and destroy a master failover netdev. When STANDBY feature is enabled, an
additional netdev(failover netdev) is created that acts as a master device
and tracks the state of the 2 lower netdevs. The original virtio_net netdev
is marked as 'standby' netdev and a passthru device with the same MAC is
registered as 'primary' netdev.
The hypervisor needs to unplug the VF device from the guest on the source
host and reset the MAC filter of the VF to initiate failover of datapath
to virtio before starting the migration. After the migration is completed,
the destination hypervisor sets the MAC filter on the VF and plugs it back
to the guest to switch over to VF datapath.
This patch is based on the discussion initiated by Jesse on this thread.
https://marc.info/?l=linux-virtualization&m=151189725224231&w=2
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The net_failover driver provides an automated failover mechanism via APIs
to create and destroy a failover master netdev and manages a primary and
standby slave netdevs that get registered via the generic failover
infrastructure.
The failover netdev acts a master device and controls 2 slave devices. The
original paravirtual interface gets registered as 'standby' slave netdev and
a passthru/vf device with the same MAC gets registered as 'primary' slave
netdev. Both 'standby' and 'failover' netdevs are associated with the same
'pci' device. The user accesses the network interface via 'failover' netdev.
The 'failover' netdev chooses 'primary' netdev as default for transmits when
it is available with link up and running.
This can be used by paravirtual drivers to enable an alternate low latency
datapath. It also enables hypervisor controlled live migration of a VM with
direct attached VF by failing over to the paravirtual datapath when the VF
is unplugged.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c40e89fd358e ("geneve: configure MTU based on a lower device") added
an IS_ENABLED(CONFIG_IPV6) to geneve, leading to the following link error
with CONFIG_GENEVE=y and CONFIG_IPV6=m:
drivers/net/geneve.o: In function `geneve_link_config':
geneve.c:(.text+0x14c): undefined reference to `rt6_lookup'
Fix this by adding a Kconfig dependency and forcing GENEVE to be a module
when IPV6 is a module.
Fixes: c40e89fd358e ("geneve: configure MTU based on a lower device")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink support to netdevsim and use it to implement a simple,
profile based resource controller. Only one controller is needed
per namespace, so the first netdevsim netdevice in a namespace
registers with devlink. If that device is deleted, the resource
settings are deleted.
The resource controller allows a user to limit the number of IPv4 and
IPv6 FIB entries and FIB rules. The resource paths are:
/IPv4
/IPv4/fib
/IPv4/fib-rules
/IPv6
/IPv6/fib
/IPv6/fib-rules
The IPv4 and IPv6 top level resources are unlimited in size and can not
be changed. From there, the number of FIB entries and FIB rule entries
are unlimited by default. A user can specify a limit for the fib and
fib-rules resources:
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib size 96
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib-rules size 16
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib size 64
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib-rules size 16
$ devlink dev reload netdevsim/netdevsim0
such that the number of rules or routes is limited (96 ipv4 routes in the
example above):
$ for n in $(seq 1 32); do ip ro add 10.99.$n.0/24 dev eth1; done
Error: netdevsim: Exceeded number of supported fib entries.
$ devlink resource show netdevsim/netdevsim0
netdevsim/netdevsim0:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables non
resources:
name fib size 96 occ 96 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables
...
With this template in place for resource management, it is fairly trivial
to extend and shows one way to implement a simple counter based resource
controller typical of network profiles.
Currently, devlink only supports initial namespace. Code is in place to
adapt netdevsim to a per namespace controller once the network namespace
issues are resolved.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We no longer depend on IPV6, but that now causes a link error with
CONFIG_IPV6=m and CONFIG_IPVLAN=y:
drivers/net/ipvlan/ipvlan_core.o: In function `ipvlan_queue_xmit':
ipvlan_core.c:(.text+0x1440): undefined reference to `ip6_route_output_flags'
drivers/net/ipvlan/ipvlan_core.o: In function `ipvlan_l3_rcv':
ipvlan_core.c:(.text+0x1818): undefined reference to `ip6_route_input_lookup'
This adds back the dependency on IPV6, with the option of building without
IPV6, but forcing IPVLAN to be a module when IPV6 is a module.
Fixes: 94333fac44d1 ("ipvlan: drop ipv6 dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L3 Master device is just a glue between the core networking code and
device drivers, so it should be selected automatically rather than
requiring to be enabled explicitly.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPVlan has an hard dependency on IPv6, refactor the ipvlan code to allow
compiling it with IPv6 disabled, move duplicate code into addr_equal()
and refactor series of if-else into a switch.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be able to run selftests without any hardware required we
need a software model. The model can also serve as an example
implementation for those implementing actual HW offloads.
The dummy driver have previously been extended to test SR-IOV,
but the general consensus seems to be against adding further
features to it.
Add a new driver for purposes of software modelling only.
eBPF and SR-IOV will be added here shortly, others are invited
to further extend the driver with their offload models.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
ThunderboltIP is a protocol created by Apple to tunnel IP/ethernet
traffic over a Thunderbolt cable. The protocol consists of configuration
phase where each side sends ThunderboltIP login packets (the protocol is
determined by UUID in the XDomain packet header) over the configuration
channel. Once both sides get positive acknowledgment to their login
packet, they configure high-speed DMA path accordingly. This DMA path is
then used to transmit and receive networking traffic.
This patch creates a virtual ethernet interface the host software can
use in the same way as any other networking interface. Once the
interface is brought up successfully network packets get tunneled over
the Thunderbolt cable to the remote host and back.
The connection is terminated by sending a ThunderboltIP logout packet
over the configuration channel. We do this when the network interface is
brought down by user or the driver is unloaded.
Signed-off-by: Amir Levy <amir.jer.levy@intel.com>
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lguest seems to be rather unused these days. It has seen only patches
ensuring it still builds the last two years and its official state is
"Odd Fixes".
Remove it in order to be able to clean up the paravirt code.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: boris.ostrovsky@oracle.com
Cc: lguest@lists.ozlabs.org
Cc: rusty@rustcorp.com.au
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20170816173157.8633-3-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add vsockmon virtual network device that receives packets from the vsock
transports and exposes them to user space.
Based on the nlmon device.
Signed-off-by: Gerard Garcia <ggarcia@deic.uab.cat>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I got a warning about broken code on ARM64 with 64K pages:
drivers/net/vmxnet3/vmxnet3_drv.c: In function 'vmxnet3_rq_init':
drivers/net/vmxnet3/vmxnet3_drv.c:1679:29: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
rq->buf_info[0][i].len = PAGE_SIZE;
'len' here is a 16-bit integer, so this clearly won't work. I don't think
this driver is used much on anything other than x86, so there is no need
to fix this properly and we can work around it with a Kconfig dependency
to forbid known-broken configurations. qemu in theory supports it on
other architectures too, but presumably only for compatibility with x86
guests that also run on vmware.
CONFIG_PAGE_SIZE_64KB is used on hexagon, mips, sh and tile, the other
symbols are architecture-specific names for the same thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a tap character device driver that is based on the
IP-VLAN network interface, called ipvtap. An ipvtap device can be created
in the same way as an ipvlan device, using 'type ipvtap', and then accessed
using the tap user space interface.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes tap a separate module for other types of virtual interfaces, for example,
ipvlan to use.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have many gro cells users, so lets move the code to avoid
duplication.
This creates a CONFIG_GRO_CELLS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kbuild-build-bot reported that if NETFILTER is not selected, the
build fails pointing to netfilter symbols.
Fixes: 4fbae7d83c98 ("ipvlan: Introduce l3s mode")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a typical IPvlan L3 setup where master is in default-ns and
each slave is into different (slave) ns. In this setup egress
packet processing for traffic originating from slave-ns will
hit all NF_HOOKs in slave-ns as well as default-ns. However same
is not true for ingress processing. All these NF_HOOKs are
hit only in the slave-ns skipping them in the default-ns.
IPvlan in L3 mode is restrictive and if admins want to deploy
iptables rules in default-ns, this asymmetric data path makes it
impossible to do so.
This patch makes use of the l3_rcv() (added as part of l3mdev
enhancements) to perform input route lookup on RX packets without
changing the skb->dev and then uses nf_hook at NF_INET_LOCAL_IN
to change the skb->dev just before handing over skb to L4.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an initial implementation of a netdev driver for GTP datapath
(GTP-U) v0 and v1, according to the GSM TS 09.60 and 3GPP TS 29.060
standards. This tunneling protocol is used to prevent subscribers from
accessing mobile carrier core network infrastructure.
This implementation requires a GGSN userspace daemon that implements the
signaling protocol (GTP-C), such as OpenGGSN [1]. This userspace daemon
updates the PDP context database that represents active subscriber
sessions through a genetlink interface.
For more context on this tunneling protocol, you can check the slides
that were presented during the NetDev 1.1 [2].
Only IPv4 is supported at this time.
[1] http://git.osmocom.org/openggsn/
[2] http://www.netdevconf.org/1.1/proceedings/slides/schultz-welte-osmocom-gtp.pdf
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new MACsec driver uses the AES crypto algorithm, but can be configured
even if CONFIG_CRYPTO is disabled, leading to a build error:
warning: (MAC80211 && MACSEC) selects CRYPTO_GCM which has unmet direct dependencies (CRYPTO)
warning: (BT && CEPH_LIB && INET && MAC802154 && MAC80211 && BLK_DEV_RBD && MACSEC && AIRO_CS && LIBIPW && HOSTAP && USB_WUSB && RTLLIB_CRYPTO_CCMP && FS_ENCRYPTION && EXT4_ENCRYPTION && CEPH_FS && BIG_KEYS && ENCRYPTED_KEYS) selects CRYPTO_AES which has unmet direct dependencies (CRYPTO)
crypto/built-in.o: In function `gcm_enc_copy_hash':
aes_generic.c:(.text+0x2b8): undefined reference to `crypto_xor'
aes_generic.c:(.text+0x2dc): undefined reference to `scatterwalk_map_and_copy'
This adds an explicit 'select CRYPTO' statement the way that other
drivers handle it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an implementation of MACsec/IEEE 802.1AE. This driver
provides authentication and encryption of traffic in a LAN, typically
with GCM-AES-128, and optional replay protection.
http://standards.ieee.org/getieee802/download/802.1AE-2006.pdf
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for IPv6 to VRF device driver. Implemenation parallels what
has been done for IPv4.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
geneve_core module handles send and receive functionality.
This way OVS could use the Geneve API. Now with use of
tunnel meatadata mode OVS can directly use Geneve netdevice.
So there is no need for separate module for Geneve. Following
patch consolidates Geneve protocol processing in single module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the basic code of FUJITSU Extended Socket
Network Device driver.
When "PNP0C02" is found in ACPI DSDT, it evaluates "_STR"
to check if "PNP0C02" is for Extended Socket device driver
and retrieves ACPI resource information. Then creates
platform_device.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using the out-of-line EWMA calculation, use DECLARE_EWMA()
to create static inlines. On x86/64 this results in no change in code
size for me, but reduces the struct receive_queue size by the two
unsigned long values that store the parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver borrows heavily from IPvlan and teaming drivers.
Routing domains (VRF-lite) are created by instantiating a VRF master
device with an associated table and enslaving all routed interfaces that
participate in the domain. As part of the enslavement, all connected
routes for the enslaved devices are moved to the table associated with
the VRF device. Outgoing sockets must bind to the VRF device to function.
Standard FIB rules bind the VRF device to tables and regular fib rule
processing is followed. Routed traffic through the box, is forwarded by
using the VRF device as the IIF and following the IIF rule to a table
that is mated with the VRF.
Example:
Create vrf 1:
ip link add vrf1 type vrf table 5
ip rule add iif vrf1 table 5
ip rule add oif vrf1 table 5
ip route add table 5 prohibit default
ip link set vrf1 up
Add interface to vrf 1:
ip link set eth1 master vrf1
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NTB updates from Jon Mason:
"This includes a pretty significant reworking of the NTB core code, but
has already produced some significant performance improvements.
An abstraction layer was added to allow the hardware and clients to be
easily added. This required rewriting the NTB transport layer for
this abstraction layer. This modification will allow future "high
performance" NTB clients.
In addition to this change, a number of performance modifications were
added. These changes include NUMA enablement, using CPU memcpy
instead of asyncdma, and modification of NTB layer MTU size"
* tag 'ntb-4.2' of git://github.com/jonmason/ntb: (22 commits)
NTB: Add split BAR output for debugfs stats
NTB: Change WARN_ON_ONCE to pr_warn_once on unsafe
NTB: Print driver name and version in module init
NTB: Increase transport MTU to 64k from 16k
NTB: Rename Intel code names to platform names
NTB: Default to CPU memcpy for performance
NTB: Improve performance with write combining
NTB: Use NUMA memory in Intel driver
NTB: Use NUMA memory and DMA chan in transport
NTB: Rate limit ntb_qp_link_work
NTB: Add tool test client
NTB: Add ping pong test client
NTB: Add parameters for Intel SNB B2B addresses
NTB: Reset transport QP link stats on down
NTB: Do not advance transport RX on link down
NTB: Differentiate transport link down messages
NTB: Check the device ID to set errata flags
NTB: Enable link for Intel root port mode in probe
NTB: Read peer info from local SPAD in transport
NTB: Split ntb_hw_intel and ntb_transport drivers
...
|
|
Pull virtio/vhost cross endian support from Michael Tsirkin:
"I have just queued some more bugfix patches today but none fix
regressions and none are related to these ones, so it looks like a
good time for a merge for -rc1.
The motivation for this is support for legacy BE guests on the new LE
hosts. There are two redeeming properties that made me merge this:
- It's a trivial amount of code: since we wrap host/guest accesses
anyway, almost all of it is well hidden from drivers.
- Sane platforms would never set flags like VHOST_CROSS_ENDIAN_LEGACY,
and when it's clear, there's zero overhead (as some point it was
tested by compiling with and without the patches, got the same
stripped binary).
Maybe we could create a Kconfig symbol to enforce the second point:
prevent people from enabling it eg on x86. I will look into this"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-pci: alloc only resources actually used.
macvtap/tun: cross-endian support for little-endian hosts
vhost: cross-endian support for legacy devices
virtio: add explicit big-endian support to memory accessors
vhost: introduce vhost_is_little_endian() helper
vringh: introduce vringh_is_little_endian() helper
macvtap: introduce macvtap_is_little_endian() helper
tun: add tun_is_little_endian() helper
virtio: introduce virtio_is_little_endian() helper
|
|
This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer. Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
The VNET_LE flag was introduced to fix accesses to virtio 1.0 headers
that are always little-endian. It can also be used to handle the special
case of a legacy little-endian device implemented by a big-endian host.
Let's add a flag and ioctls for big-endian devices as well. If both flags
are set, little-endian wins.
Since this is isn't a common usecase, the feature is controlled by a kernel
config option (not set by default).
Both macvtap and tun are covered by this patch since they share the same
API with userland.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This is an initial implementation of a netdev driver for GENEVE
tunnels. This implementation uses a fixed UDP port, and only supports
point-to-point links with specific partner endpoints. Only IPv4
links are supported at this time.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|