Age | Commit message (Collapse) | Author |
|
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.
Fixes: 10050a02f7d5 ("mtd: spi-nor: Add 4B_OPCODES flag to w25q256")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Despite of how spi_nor_parse_bfpt() abuses the structure fields during
their calculation, gcc manages to make some decent code out of that. :-)
Yet adding a local variable to store the BFPT DWORDs during calculations
still saves 12 bytes of the object code (AArch64 gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
JESD216 rev D makes BFPT 20 DWORDs. Update the BFPT size define to
reflect that.
The check for rev A or later compared the BFPT header length with the
maximum BFPT length, BFPT_DWORD_MAX. Since BFPT_DWORD_MAX was 16, and so
was the BFPT length for both rev A and B, this check worked fine. But
now, since BFPT_DWORD_MAX is 20, it means this check will also stop BFPT
parsing for rev A or B, since their length is 16.
So, instead check for BFPT_DWORD_MAX_JESD216 to stop BFPT parsing for
the first JESD216 version, and check for BFPT_DWORD_MAX_JESD216B for the
next two versions.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
JESD216D.01 says that when the address width can be 3 or 4, it defaults
to 3 and enters 4-byte mode when given the appropriate command. So, when
we see a configurable width, default to 3 and let flash that default to
4 change it in a post-bfpt fixup.
This fixes SMPT parsing for flashes with configurable address width. If
the SMPT descriptor advertises variable address width, we use
nor->addr_width as the address width. But since it was not set to any
value from the SFDP table, the read command uses an address width of 0,
resulting in an incorrect read being issued.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The Cypress cy15b104q and cy15v104q are 4Mbit serial SPI F-RAM devices.
Add support for them to the spi-nor driver.
The actual Device ID of this chip is 7f 7f 7f 7f 7f 7f c2 2c 04. That is
six times the continuation code 7f followed by c2 for Ramtron.
Unfortunately the chip sends the Device ID in reversed order, so the
continuation code is not at the beginning, but instead at the end. Even
more unfortunate is that when reading further the chip sends more 7f
codes which means we are not even able to count the continuation codes.
We can only hope that this reversed Device ID will never match any other
devices ID.
Collisions are improbable as of now, the solution from above is good
enough. In case of future collisions one can introduce an INFO9 macro,
with the downsize that struct flash_info would grow and we have lots of
flashes. A more elegant solution would be to introduce dedicated
flash ID tables for each bank in JESP106BA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[tudor.ambarus@microchip.com: amend commit description with possible
future solutions in case collisions occur.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The correct terminology is serial NOR flash or SPI NOR.
s/SPI-NOR/SPI NOR and s/spi-nor/SPI NOR across the subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
|
|
s25fs256s was identified as s25fl256s. Differentiate between them by
the Family ID using the INFO6 macro.
Fixes: b199489d37b2 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
|
|
Add support for Cypress s25fs128s1 flash. Previously the flash is
decoded as s25fl129p1 by mistake.
Add it in the flash info list to correctly decode. The flash also
needs a fixup for s25fs-s family. Further capability of the flash will
be parsed from bfpt.
The flash has been tested under SPI/DUAL/QUAD mode on hisi-sfc-v3xx
controller, all the write/read/erase works well.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Spansion S25FS-S family has an issue in the Basic Flash Parameter Table
(BFPT): Dword-11 bits 7:4 specify a page size of 512 bytes. Actually
this is configurable in the vendor unique register (CR3V) and even the
factory default setting is to "wrap at 256 bytes", so blindly relying
on BFPT breaks the page writes on these chips. Add the post-BFPT fixup
which restores the default page size of 256 bytes -- to properly read
CR3V this early is quite intrusive and should better be done as a new
feature; Alexander Sverdlin had the patch doing that:
https://patchwork.ozlabs.org/project/linux-mtd/patch/20200227123657.26030-1-alexander.sverdlin@nokia.com/
Fixes: dfd2b74530e ("mtd: spi-nor: add Spansion S25FS512S ID")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The functions return 1 if ready, 0 if not ready, -errno on errors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
spi_nor_ready() returns 1 if ready, 0 if not ready and -errno on errors.
Do the same in all the spi_nor_*_ready() children.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
n25q00 uses the 4 bit Block Protection scheme and supports Top/Bottom
protection via the BP and TB bits of the Status Register.
Enable locking for n25q00. Tested with cirrus controller.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
mx25u51245g is a mass production for new design and
replace mx66u51235f(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
mx25l51245g is a mass production for new design and
replace mx66l51235l(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
When spi_nor_info_init_params(), spi_nor_sfdp_init_params(), and
spi_nor_init_params() were added, the kernel-doc for them contained
a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix them.
Fixes: 1c1d8d98e1c7 ("mtd: spi-nor: Split spi_nor_init_params()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
When spi_nor_manufacturer_init_params() was added, the kernel-doc for it
contained a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix it.
Fixes: ce0b6f3f3c43 ("mtd: spi-nor: Add default_init() hook to tweak flash parameters")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
As 4bit block protection patchset for some micron models are merged,
n25q128a11 also uses 4 bit Block Protection scheme, so enable locking
for it. Tested it on n25q128a11, the locking functions work well.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Tested-by: Shreyas Joshi <shreyasjoshi15@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry. Tested with the device and
confirmed that is working.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Commit a0900d0195d2 ("mtd: spi-nor: Prepare core / manufacturer code
split") moved various files into a new directory, but did not add the new
directory to its parent directory Makefile. The moved files no longer
build, and affected flash chips no longer instantiate.
Adding the new directory to the parent directory Makefile fixes the
problem.
Fixes: a0900d0195d2 ("mtd: spi-nor: Prepare core / manufacturer code split")
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Use Joe Perches cvt_fallthrough.pl script to convert
/* fallthrough */
comments (and its derivatives) into a
fallthrough;
statement. This automatically drops useless ones.
Do it MTD-wide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20200325212115.14170-1-miquel.raynal@bootlin.com
|
|
n25q512ax3 and n25q512a use the 4 bit Block Protection scheme.
Enable locking for both. Tested on n25q512ax3. The other is modified
following the datasheet.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Currently we are supporting block protection only for flash chips with
3 block protection bits (BP0-2) in the SR register.
Enable block protection support for flashes with 4 block protection bits
(BP0-3).
Add a flash_info flag for flashes that describe 4 block protection bits.
Add another flash_info flag for flashes in which BP3 bit is not adjacent
to the BP0-2 bits.
Tested with a n25q512ax3 (BP0-3) and w25q128 (BP0-2).
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The current mainline locking was restricted and could only be applied
to flashes that have 3 block protection bits and fixed locking ratio.
A new method of normalization was reached at the end of the discussion [1].
(1) - if bp slot is insufficient.
(2) - if bp slot is sufficient.
if (bp_slots_needed > bp_slots) // (1)
min_prot_length = sector_size << (bp_slots_needed - bp_slots);
else // (2)
min_prot_length = sector_size;
This patch changes logic to handle block protection based on min_prot_length.
It is suitable for the overall flashes with exception of some corner cases
(see EON and catalyst) and easy to extend and apply for the case of 2bit or
4bit block protection.
[1] http://lists.infradead.org/pipermail/linux-mtd/2020-February/093934.html
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
When there are more BP settings than needed for defining the protected
areas of the flash memory, most flashes will define the remaining
settings as "protect all", i.e. the equivalent of having all the BP bits
set to one. But there are flashes where the in-between BP values
are undefined (not mentioned), and only the "all bits set" is protecting
the entire memory. One such example is w25q80, where BP[2:0]=0b101 and
0b110 are not defined.
Set all the BP bits to one when lock_len == mtd->size, to treat this
special case.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
|
|
flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
When an Erase or Program error occurs on a spansion/cypress or a
micron flash, the WEL bit remains set to one and should be cleared
with a WRDI command in order to protect against inadvertent writes
that can possible corrupt the contents of the memory.
Winbond, macronix, gd, etc., do not support the E_ERR and P_ERR bits in the
Status Register and always clear the WEL bit regardless of the outcome
of the erase or page program operation (ex w25q40bw, MX25L25635E).
Issue a WRDI command when erase or page program errors occur.
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
|
|
The SPI NOR controllers drivers must not be able to use structures that
are meant just for the SPI NOR core.
struct spi_nor_flash_parameter is filled at run-time with info gathered
from flash_info, manufacturer and sfdp data. struct spi_nor_flash_parameter
should be opaque to the SPI NOR controller drivers, make sure it is.
spi_nor_option_flags, spi_nor_read_command, spi_nor_pp_command,
spi_nor_read_command_index and spi_nor_pp_command_index are defined for the
core use, make sure they are opaque to the SPI NOR controller drivers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Cross manufacturer code is unlikely and discouraged, get rid of the
MFR definitions.
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
All entries have been moved to manufacturer drivers. Get rid of this
empty table.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Create a SPI NOR manufacturer driver for XMC chips, and move the
XMC definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Xilinx chips, and move the
Xilinx definitions outside of core.c.
While at it, remove the SPI_S3AN flag which is now useless.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Catalyst chips, and move the
Catalyst definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Winbond chips, and move the
Winbond definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for SST chips, and move the
SST definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Spansion chips, and move the
Spansion definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Micron/ST chips, and move the
Micron/ST definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Macronix chips, and move the
Macronix definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
|
|
Create a SPI NOR manufacturer driver for ISSI chips, and move the
ISSI definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Intel chips, and move the
Intel definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Create a SPI NOR manufacturer driver for GigaDevice chips, and move the
GigaDevice definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Fujitsu chips, and move the
Fujitsu definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Everspin chips, and move the
Everspin definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for ESMT chips, and move the
ESMT definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Eon chips, and move the
Eon definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Create a SPI NOR manufacturer driver for Atmel chips, and move the
Atmel definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Declare a spi_nor_manufacturer struct and add basic building blocks to
move manufacturer specific code outside of the core.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Expose the flash_info struct and some function prototypes that
will be used by manufacturers.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
It makes the core file a bit smaller and provides better separation
between the SFDP parsing and core logic.
Keep the core.h and sfdp.h definitions private in drivers/mtd/spi-nor/.
Both expose just the definitions that are required by the core and
manufacturer drivers. None of the SPI NOR controller drivers should
include them.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Move all SPI NOR controller drivers to a controllers/ sub-directory
so that we only have SPI NOR related source files under
drivers/mtd/spi-nor/.
Rename spi-nor.c into core.c, we are about to split this file in multiple
source files (one per manufacturer, plus one for the SFDP parsing logic).
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Rename (*set_4byte)() to (*set_4byte_addr_mode)() for a better
differentiation between the 4 byte address mode and opcodes.
Rename macronix_set_4byte() to spi_nor_set_4byte_addr_mode(), it will be
the only 4 byte address mode method exposed to the manufacturer drivers.
Here's how the manufacturers enter and exit the 4 byte address mode:
- eon, gidadevice, issi, macronix, xmc use EN4B/EX4B
- micron-st needs WEN. st_micron_set_4byte_addr_mode() will become
a private method, as they are the only ones that need WEN before the
EN4B/EX4B commands.
- newer spansion have a 4BAM opcode (this translates to a new, public
command). Older spansion flashes use the BRWR command (legacy in
core.c -> spansion_set_4byte_addr_mode())
- winbond's method is hackish and may be reason for just a flash
fixup hook -> private method
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|