| Age | Commit message (Collapse) | Author |
|---|
|
Add a common function used for read_raw callback for both PMIC5
and PMIC7 ADCs.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add the ability to also support access via (triggered) buffers
next to the existing direct mode.
Device in question is the Odroid Go Advance that connects a joystick
to two of the saradc channels for X and Y axis and the new (and still
pending) adc joystick driver of course wants to use triggered buffers
from the iio subsystem.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
[some simplifications and added commit description]
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
As suggested give the current ADC_CHANNEL constant a distinct
and consistent prefix.
Suggested-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Parts of the saradc probe rely on devm functions and later parts do not.
This makes it more difficult to for example enable triggers via their
devm-functions and would need more undo-work in remove.
So to make life easier for the driver, move the rest of probe calls
also to their devm-equivalents.
This includes moving the clk- and regulator-disabling to a devm_action
so that they gets disabled both during remove and in the error case
in probe, after the action is registered.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
All devices using a triggered buffer need to attach and detach the trigger
to the device in order to properly work. Instead of doing this in each and
every driver by hand move this into the core.
At this point in time, all drivers should have been resolved to
attach/detach the poll-function in the same order.
This patch removes all explicit calls of iio_triggered_buffer_postenable()
& iio_triggered_buffer_predisable() in all drivers, since the core handles
now the pollfunc attach/detach.
The more peculiar change is for the 'at91-sama5d2_adc' driver, since it's
not immediately obvious that removing the hooks doesn't break anything.
Eugen was able to test on at91-sama5d2-adc driver, sama5d2-xplained board.
All seems to be fine.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com> #for at91-sama5d2-adc
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We may want to get rid of the iio_priv_to_dev() helper. The reason is that
we will hide some of the members of the iio_dev structure (to prevent
drivers from accessing them directly), and that will also mean hiding the
implementation of the iio_priv_to_dev() helper inside the IIO core.
Hiding the implementation of iio_priv_to_dev() implies that some fast-paths
may not be fast anymore, so a general idea is to try to get rid of the
iio_priv_to_dev() altogether.
The iio_priv() helper won't be affected by the rework, as the iio_dev
struct will keep a reference to the private information.
For this driver, not using iio_priv_to_dev(), means reworking some paths to
pass the iio device and using iio_priv() to access the private information.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We may want to get rid of the iio_priv_to_dev() helper. The reason is that
we will hide some of the members of the iio_dev structure (to prevent
drivers from accessing them directly), and that will also mean hiding the
implementation of the iio_priv_to_dev() helper inside the IIO core.
Hiding the implementation of iio_priv_to_dev() implies that some fast-paths
may not be fast anymore, so a general idea is to try to get rid of the
iio_priv_to_dev() altogether.
The iio_priv() helper won't be affected by the rework, as the iio_dev
struct will keep a reference to the private information.
For this driver, not using iio_priv_to_dev(), means reworking some paths to
pass the iio device and using iio_priv() to access the private information.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
If a driver does not assign an of_node to a IIO device to IIO core will
automatically assign the of_node of the parent device. This automatic
assignment is done in the iio_device_register() function.
There is a fair amount of drivers that currently manually assign the
of_node of the IIO device. All but 4 of them can make use of the automatic
assignment though.
The exceptions are:
* mxs-lradc-adc: Which uses the of_node of the parent of the parent.
* stm32-dfsdm-adc, stm32-adc and stm32-dac: Which reference the of_node
assigned to the IIO device before iio_device_register() is called.
All other drivers are updated to use automatic assignment. This reduces
the amount of boilerplate code involved in setting up the IIO device.
The patch has mostly been auto-generated with the following semantic patch
// <smpl>
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(&parent, ...)
...
-indio_dev->dev.of_node = parent.of_node;
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(parent, ...)
...
-indio_dev->dev.of_node = parent->of_node;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
These were found by doing some shell magic:
------------
for file in $(git grep -w devm_iio_device_alloc | cut -d: -f1 | sort | uniq) ; do
if grep 'parent =' $file | grep -v trig | grep -vq devm_; then
echo "$file -> $(grep "parent =" $file)"
fi
done
-----------
The output is bearable [after the semantic patch is applied].
There is a mix of trigger assignments with some iio device parent
assignments that are removed via this patch.
JC: A few more added via inspection of all parent =
statements in drivers/iio. Some of these may just have crossed with this
series, others were less obvious to scripting due to some cross
file / module boundary calls.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
These were obtained by doing a 'git diff | grep \/\*', in the previous diff
to find comments. These needed a bit more manual review, as the semantic
patch isn't great for catching these.
The result is:
/* Initialize Counter device and driver data */
/* Initialize IIO device */
/* Establish that the iio_dev is a child of the spi device */
/* Estabilish that the iio_dev is a child of the spi device */
/* Initiate the Industrial I/O device */
/* Establish that the iio_dev is a child of the device */
- /* establish that the iio_dev is a child of the i2c device */
- /* establish that the iio_dev is a child of the i2c device */
/* This is only used for removal purposes */
/* setup the industrialio driver allocated elements */
/* variant specific configuration */
/* Setup for userspace synchronous on demand sampling. */
st->readback_delay_us += 5; /* Add tWAIT */
- /* Establish that the iio_dev is a child of the i2c device */
/* Establish that the iio_dev is a child of the i2c device */
Out of which, 4 are really left-over comments about parent assignment.
3 of them are removed by the semantic patch, as the comment removed (by
spatch) would be for an empty line.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;
It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'
But this is is only done in case where the block is left empty.
The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.
However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since changes can come from all sort of places, it may make sense to have
this symbol as a dependency to make sure that the 'make allmodconfig' &&
'make allyesconfig' build rules cover this driver as well for a
compile-build/test.
It seemed useful [recently] when trying to apply a change for this.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We may want to get rid of the iio_priv_to_dev() helper. The reason is that
we will hide some of the members of the iio_dev structure (to prevent
drivers from accessing them directly), and that will also mean hiding the
implementation of the iio_priv_to_dev() helper inside the IIO core.
Hiding the implementation of iio_priv_to_dev() implies that some fast-paths
may not be fast anymore, so a general idea is to try to get rid of the
iio_priv_to_dev() altogether.
The iio_priv() helper won't be affected by the rework, as the iio_dev
struct will keep a reference to the private information.
For this driver, not using iio_priv_to_dev(), means reworking some paths to
pass the iio device and using iio_priv() to access the private information.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
max11100_channels is not modified and can therefore be made const to
allow the compiler to put it in read-only memory.
Before:
text data bss dec hex filename
3776 1168 0 4944 1350 drivers/iio/adc/max11100.o
After:
text data bss dec hex filename
3968 976 0 4944 1350 drivers/iio/adc/max11100.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Change pr_err/pr_debug statements to dev_err/dev_dbg for
increased clarity.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Clean up some return value checks to make code more compact.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADC architecture on PMIC7 is changed as compared to PMIC5. The
major change from PMIC5 is that all SW communication to ADC goes through
PMK8350, which communicates with other PMICs through PBS when the ADC
on PMK8350 works in master mode. The SID register is used to identify the
PMICs with which the PBS needs to communicate. Add support for the same.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add info property under adc_data to support adding ADC variants
which may use different iio_info than the one defined for PMIC5.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the large set of staging and IIO driver changes for 5.8-rc1
Nothing major, but a lot of new IIO drivers are included in here,
along with other core iio cleanups and changes.
On the staging driver front, again, nothing noticable. No new
deletions or additions, just a ton of tiny cleanups all over the tree
done by a lot of different people. Most coding style, but many actual
real fixes and cleanups that are nice to see.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (618 commits)
staging: rtl8723bs: Use common packet header constants
staging: sm750fb: Add names to proc_setBLANK args
staging: most: usb: init return value in default path of switch/case expression
staging: vchiq: Get rid of VCHIQ_SERVICE_OPENEND callback reason
staging: vchiq: move vchiq_release_message() into vchiq
staging: vchi: Get rid of C++ guards
staging: vchi: Get rid of not implemented function declarations
staging: vchi: Get rid of vchiq_status_to_vchi()
staging: vchi: Get rid of vchi_service_set_option()
staging: vchi: Merge vchi_msg_queue() into vchi_queue_kernel_message()
staging: vchiq: Move copy callback handling into vchiq
staging: vchi: Get rid of vchi_queue_user_message()
staging: vchi: Get rid of vchi_service_destroy()
staging: most: usb: use function sysfs_streq
staging: most: usb: add missing put_device calls
staging: most: usb: use correct error codes
staging: most: usb: replace code to calculate array index
staging: most: usb: don't use error path to exit function on success
staging: most: usb: move allocation of URB out of critical section
staging: most: usb: return 0 instead of variable
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Constify 'properties' attribute in core header file
New Drivers:
- Add support for Gateworks System Controller
- Add support for MediaTek MT6358 PMIC
- Add support for Mediatek MT6360 PMIC
- Add support for Monolithic Power Systems MP2629 ADC and Battery charger
Fix-ups:
- Use new I2C API in htc-i2cpld
- Remove superfluous code in sprd-sc27xx-spi
- Improve error handling in stm32-timers
- Device Tree additions/fixes in mt6397
- Defer probe betterment in wm8994-core
- Improve module handling in wm8994-core
- Staticify in stpmic1
- Trivial (spelling, formatting) in tqmx86
Bug Fixes:
- Fix incorrect register/PCI IDs in intel-lpss-pci
- Fix unbalanced Regulator API calls in wm8994-core
- Fix double free() in wcd934x
- Remove IRQ domain on failure in stmfx
- Reset chip on resume in stmfx
- Disable/enable IRQs on suspend/resume in stmfx
- Do not use bulk writes on H/W which does not support them in max77620"
* tag 'mfd-next-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (29 commits)
mfd: mt6360: Remove duplicate REGMAP_IRQ_REG_LINE() entry
mfd: Add support for PMIC MT6360
mfd: max77620: Use single-byte writes on MAX77620
mfd: wcd934x: Drop kfree for memory allocated with devm_kzalloc
mfd: stmfx: Disable IRQ in suspend to avoid spurious interrupt
mfd: stmfx: Fix stmfx_irq_init error path
mfd: stmfx: Reset chip on resume as supply was disabled
mfd: wm8994: Silence warning about supplies during deferred probe
mfd: wm8994: Fix unbalanced calls to regulator_bulk_disable()
mfd: wm8994: Fix driver operation if loaded as modules
dt-bindings: mfd: mediatek: Add MT6397 Pin Controller
mfd: Constify properties in mfd_cell
mfd: stm32-timers: Use dma_request_chan() instead dma_request_slave_channel()
mfd: sprd: Remove unnecessary spi_bus_type setting
mfd: intel-lpss: Update LPSS UART #2 PCI ID for Jasper Lake
mfd: tqmx86: Fix a typo in MODULE_DESCRIPTION
mfd: stpmic1: Make stpmic1_regmap_config static
mfd: htc-i2cpld: Convert to use i2c_new_client_device()
MAINTAINERS: Add entry for mp2629 Battery Charger driver
power: supply: mp2629: Add impedance compensation config
...
|
|
Add support for 8-bit resolution ADC readings for input power
supply and battery charging measurement. Provides voltage, current
readings to mp2629 power supply driver.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We need the staging/iio fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A wrong error message is printed out currently, like on STM32MP15:
- stm32-adc-core 48003000.adc: IRQ index 2 not found.
This is seen since commit 7723f4c5ecdb ("driver core: platform: Add an
error message to platform_get_irq*()").
The STM32 ADC core driver wrongly requests up to 3 interrupt lines. It
should request only the necessary IRQs, based on the compatible:
- stm32f4/h7 ADCs share a common interrupt
- stm32mp1, has one interrupt line per ADC.
So add the number of required interrupts to the compatible data.
Fixes: d58c67d1d851 ("iio: adc: stm32-adc: add support for STM32MP1")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The Exynos7-specific code bits in ADC driver do not play with PHY:
the field exynos_adc_data.needs_adc_phy is not set in exynos7_adc_data
instance. Therefore the initialization code does not have to check if
it is true.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently the driver only exposes the raw counts. As we
have the regulator voltage and the maximum value (stored in
the data mask), we can trivially produce a scaling fraction
of voltage / max value.
This assumes that the regulator voltage is in fact the max
voltage, which appears to be the case for all mainline dts
and cross referenced with the public Exynos4412 and S5PV210
datasheets.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, cleanups and features for IIO in the 5.8 cycle
Usual mixed back but with a few subsystem wide or device type
wide cleanups.
New device support
* adis16475
- New driver supporting adis16470, adis16475, adis16477, adis16465,
adis16467, adis16500, adis16505 and adis16507.
Includes some rework of the adis library to simplify using it
for this new driver.
* ak8974
- Add support for Alps hscdt008a. ID only. Related patches add support
for scale.
* atlas-sensor
- Add support for RTD-SM OEM temperature sensor.
* cm32181
- Add support for CM3218 including support for SMBUS alert via
ACPI resources.
* ltc2632
- Add support for ltc2634-12/10/8 DACS including handling per
device type numbers of channels.
Major Features
* cm32181
- ACPI bindings including parsing CPM0 and CPM1 custom ACPI tables.
Includes minor tidy ups and fixes.
* vcnl4000
- Add event support
- Add buffered data capture support
- Add control of sampling frequency
Cleanups and minor fixes.
* core
- Trivial rework of iio_device_alloc to use an early return and
improve readability.
- Precursors to addition of multiple buffer support. So far
minor refactoring.
* subsystem wide
- Use get_unaligned_be24 slightly improve readability over open
coding it.
* adis drivers
- Use iio_get_debugfs_dentry access function.
* bh1780, cm32181, cm3232, gp2ap02a00f, opt3001, st_uvis25, vl6180,
dmard06, kxsd9
- Drop use of of_match_ptr to allow ACPI based probing via PRP0001.
Part of clear out of this to avoid cut and paste into new drivers.
* ad5592r, ad5593r
- Fix typos
* ad5933
- Use managed interfaces to automate error handling and remove.
* ak8974
- Fix wrong number of 'real bits' for buffered data.
- Refactor to pull measurement code out as separate function.
bmp280
- Fix lack of clamp on range during data capture.
* at91-sama5d2_adc
- Handle unfinished conversions correctly.
- Allow use of triggers other than it's own.
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ccs811
- Add DT binding docs and match table.
- Support external reset and wakeup pins.
* hid-sensors
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ltr501
- Constify some structs.
* vcnl4000
- Fix an endian issue by using explicit byte swapped i2c accessors.
* tag 'iio-for-5.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (74 commits)
iio: light: ltr501: Constify structs
staging: iio: ad5933: attach life-cycle of kfifo buffer to parent device and use managed calls throughout
iio: bmp280: fix compensation of humidity
iio: light: cm32181: Fix integartion time typo
iio: light: cm32181: Add support for parsing CPM0 and CPM1 ACPI tables
iio: light: cm32181: Make lux_per_bit and lux_per_bit_base_it runtime settings
iio: light: cm32181: Use units of 1/100000th for calibscale and lux_per_bit
iio: light: cm32181: Change reg_init to use a bitmap of which registers to init
iio: light: cm32181: Handle CM3218 ACPI devices with 2 I2C resources
iio: light: cm32181: Clean up the probe function a bit
iio: light: cm32181: Add support for the CM3218
iio: light: cm32181: Add some extra register defines
iio: light: cm32181: Add support for ACPI enumeration
iio: light: cm32181: Switch to new style i2c-driver probe function
iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger
iio: vcnl4000: Add buffer support for VCNL4010/20.
iio: vcnl4000: Add sampling frequency support for VCNL4010/20.
iio: vcnl4000: Add event support for VCNL4010/20.
iio: vcnl4000: Factorize data reading and writing.
iio: vcnl4000: Fix i2c swapped word reading.
...
|
|
DMA channel request should use device struct from platform device struct.
Currently it's using iio device struct. But at this stage when probing,
device struct isn't yet registered (e.g. device_register is done in
iio_device_register). Since commit 71723a96b8b1 ("dmaengine: Create
symlinks between DMA channels and slaves"), a warning message is printed
as the links in sysfs can't be created, due to device isn't yet registered:
- Cannot create DMA slave symlink
- Cannot create DMA dma:rx symlink
Fix this by using device struct from platform device to request dma chan.
Fixes: eca949800d2d ("IIO: ADC: add stm32 DFSDM support for PDM microphone")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
DMA channel request should use device struct from platform device struct.
Currently it's using iio device struct. But at this stage when probing,
device struct isn't yet registered (e.g. device_register is done in
iio_device_register). Since commit 71723a96b8b1 ("dmaengine: Create
symlinks between DMA channels and slaves"), a warning message is printed
as the links in sysfs can't be created, due to device isn't yet registered:
- Cannot create DMA slave symlink
- Cannot create DMA dma:rx symlink
Fix this by using device struct from platform device to request dma chan.
Fixes: 2763ea0585c99 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
During initial submission the selection of the channel was done using
the scan_index member of the iio_chan_spec structure. It was an abuse
because this member is supposed to be used with a buffer so it was
removed.
However there was still the need to be able to known how to select a
channel, the correct member to store this information is address.
Thanks to this it is possible to select any other channel than the
channel 0.
Fixes: 8dd2d7c0fed7 ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The null check on st->chip_info->convst_channel is redundant because
convst_channel is a 2 element array of struct iio_chan_spec objects
and this can never be null. Fix this by removing the null check.
Addresses-Coverity: ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This makes the driver code slightly easier to read.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We need the staging fixes in here too, and this resolves a merge issue
with the vt6656 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
positions
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
poll functions.
In most cases the iio_triggered_buffer_postenable() should be called first
to attach the poll function, and then the driver can init the data to be
triggered.
In this case it's the other way around: the DMA code should be initialized
before the attaching the poll function and the reverse should be done when
un-initializing.
To make things easier when removing the iio_triggered_buffer_postenable() &
iio_triggered_buffer_predisable() functions from the IIO core API, the DMA
code has been moved into preenable() for init, and postdisable() for
uninit.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change moves the logic to check if the current channel is the
touchscreen channel to a separate helper.
This reduces some code duplication, but the main intent is to re-use this
in the next patches.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change will allow the at91-sama5d2_adc driver to use other triggers
than it's own.
In particular, tested with the sysfs trigger.
To be able to achieve this functionality, some changes were required:
1) Do not enable/disable channels when enabling/disabling the trigger.
This is because the trigger is enabled/disabled only for our trigger
(obviously). We need channels enabled/disabled regardless of what trigger is
being used.
2) Cope with DMA : DMA cannot be used when using another type of trigger.
Other triggers work through pollfunc, so we get polled anyway on every trigger.
Thus we have to obtain data at every trigger.
3) When to start conversion? The usual pollfunc (store time from subsystem)
would be in hard irq and this would be a good way, but current iio subsystem
recommends to have it in the threaded irq. Thus adding software start
code in this handler.
4) Buffer config: we need to setup buffer regardless of our own device's
trigger. We may get one attached later.
5) IRQ handling: we use our own device IRQ only if it's our own trigger
and we do not use DMA . If we use DMA, we use the DMA controller's IRQ.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
It can happen that on IRQ trigger, not all conversions are done if
we are enabling multiple channels.
The IRQ is triggered on first EOC (end of channel), but it can happen
that not all channels are done. This leads into erroneous reports to
userspace (zero values or previous values).
To solve this, in trigger handler, check if the mask of done channels
is the same as the mask of active scan channels.
If it's the same, proceed and push to buffers. Otherwise, use usleep
to sleep until the conversion is done or we timeout.
Normally, it should happen that in a short time fashion, all channels are
ready, since the first IRQ triggered.
If a hardware fault happens (for example the clock suddently dissappears),
the handler will not be completed, in which case we do not report anything to
userspace anymore.
Also, change from using the EOC interrupts to DRDY interrupt.
This helps with the fact that not 'n' interrupt statuses are enabled,
each being able to trigger an interrupt, and instead only data ready
interrupt can wake up the CPU. Like this, when data is ready, check in
handler which and how many channels are done. While the DRDY is raised,
other IRQs cannot occur. Once the channel data is being read, we ack the
IRQ and finish the conversion.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
|
|
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be38 ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fed7 ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
simultaneous mode
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
According to https://www.analog.com/, the company name is spelled
"Analog Devices".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use |
