| Age | Commit message (Collapse) | Author |
|---|
|
'for-4.5/container-of-cleanups', 'for-4.5/core', 'for-4.5/i2c-hid', 'for-4.5/logitech', 'for-4.5/multitouch', 'for-4.5/sony', 'for-4.5/upstream' and 'for-4.5/wacom' into for-linus
|
|
This needs same quirk as applied to other YOGA sensor hubs. Refer to commit
21589ebda681 ("HID: sensor-hub: Add in quirk for Lenovo Yogas with ITE")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
There seems to be a new version of the Microchip Pick16F1454 with a
different PID (0xf2f7). This device should also be ignored by the HID
driver. The PID was observed with the second version of the Yepkit Ykush
USB hub.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Unlike other tablets which are compatible with the wacom_intuos_irq handler,
INTUOSHT2 devices provide pen ID with report ID 8 instead of 5. To ensure
wacom_intuos_schedule_prox_event works as intended for these tablets, we
must be sure it uses the correct report ID in this case.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: linux-input@vger.kernel.org
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When an i2c-hid device is resumed from system sleep the driver resets
the device to be sure it is in known state. The device is expected to
issue an interrupt when reset is complete.
This reset might take few milliseconds to complete so if the HID driver
on top (hid-rmi) starts to set up the device by sending feature reports
etc. the device might not issue the reset complete interrupt anymore.
Below is what happens to touchpad on Lenovo Yoga 900 during resume from
system sleep:
[ 24.790951] i2c_hid i2c-SYNA2B29:00: i2c_hid_hwreset
[ 24.790973] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 24.790982] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 08
[ 24.793011] i2c_hid i2c-SYNA2B29:00: resetting...
[ 24.793016] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 01
Here i2c-hid sends reset command to the touchpad.
[ 24.794012] i2c_hid i2c-SYNA2B29:00: input: 06 00 01 00 00 00
[ 24.794051] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.794059] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=22 00 3f 03 0f 23 00 04 00 0f 01
Now hid-rmi puts the touchpad to correct mode by sending it a feature
report. This makes the touchpad not to issue reset complete interrupt.
[ 24.796092] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: waiting...
i2c-hid starts to wait for the reset interrupt to trigger which never
happens.
[ 24.798304] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.798313] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=25 00 17 00 09 01 42 00 2e 00 19 19 00 10 cc 06 74 04 0f
19 00 00 00 00 00
Yet another output report from hid-rmi driver.
[ 29.795630] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: finished.
[ 29.795637] i2c_hid i2c-SYNA2B29:00: failed to reset device.
After 5 seconds i2c-hid driver times out.
[ 29.795642] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 29.795649] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 01 08
[ 29.797576] dpm_run_callback(): i2c_hid_resume+0x0/0xb0 returns -61
[ 29.797584] PM: Device i2c-SYNA2B29:00 failed to resume: error -61
After this the touchpad does not work anymore (and also resume itself
gets slowed down because of the timeout).
Prevent sending of feature/output reports while the device is being
reset by adding a mutex which is held during that time.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Nish Aravamudan <nish.aravamudan@gmail.com>
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use dev_to_wii() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add a new helper to_hid_driver() and use it in hid-core.c.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use to_hid_device() instead of container_of().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
to_hid_device() macro is defined in both hid-lg4ff.c and
hid-logitech-hidpp.c. So I move it to include/linux/hid.h.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use to_usb_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Clément Vuchener <clement.vuchener@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Linux 4.4-rc6
|
|
This mouse, when asked about the battery, ceases to report movements and
clicks. So just don't ask.
Signed-off-by: Alexander E. Patrakov <patrakov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit c7f0522 incorrectly constructs the 'buttons' variable for the
CINTIQ_COMPANION_2 case. The high nybble of data[2] is shifted four
bits too far, leaving the bits associated with BTN_7 through BTN_A
unset.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit c7f0522 reports incorrect touchring values to userspace. This is
due to its incorrect handling of the 'touched' bit present in the 'ring1'
and 'ring2' variables. Instead of using this bit when determining if a
value should be sent, the ABS_WHEEL and ABS_INPUT check (different?!)
portions of the position bits. Furthermore, the full values of 'ring1'
and 'ring2' are reported to userspace, despite the 'touched' flag
needing to be trimmed beforehand. This commit addresses both issues.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit c7f0522 accidentally used ABS_RX for reporting both 'strip1' and
'strip2', when the latter should actually be reported through ABS_RY.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit c7f0522 uses sixteen bits of data in the construction of 'strip1'
and 'strip2'. This can cause problems in some cases, however, since some
tablets store flags in the MSB of data[2] and data[4] that should not be
included in these values. This restores the 0x1f mask that used prior
to c7f0522.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Smatch complains that these should probably be bitwise ORs instead of
logical. It doesn't matter for "prox" but it makes a difference for
"strip1" and "strip2".
Fixes: c7f0522a1ad1 ('HID: wacom: Slim down wacom_intuos_pad processing')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
|
|
When splitting the touch-only "BAMBOO_TOUCH" type out of the existing
"BAMBOO_PT" type in 3b164a00, the lowres quirk was not updated so that
it would continue to apply to these devices (effectively only the 0xD0).
The absence of this quirk does not significantly impact usability, but
is a correctness issue nonetheless.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition timing dependency between devices. This
patch enables hid devices to suspend/resume asynchronously. This
will take advantage of multicore and improve system suspend/resume
speed.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
"INTUOSREAD" and "INTUOSWRITE" are poorly named. These are report IDs
for pen ID (proximity) packets. It should be noted that the latter is
only used on Intuos/Intuos2 for a second stylus when DualTrack is in use.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Make the logic for reading X, Y, distance, and pressure a bit more
clear. An additional bit was stuffed into the packet format many
models back, and /most/ devices in use will use it. If we happen
to be dealing with a particularly old tablet, just shift it off
the end to pretend we never read it.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Continue re-organizing and trimming cases to make it easier to wrap
the brain around. A number of changes were made after consulting the
protocol spec and so don't necessarily follow from the code itself.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Reasoning through the conditions under which a particular block of code
in 'wacom_intuos_general' will be reached is not at all easy due to the
sheer number of magic masks and comparisons. Remove these and replace
them with a switch statement over the various 'types' of packets that
will be encountered.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Continue to slim down 'wacom_intuos_irq' by moving all decoding and
reporting of pen packet data into the 'wacom_intuos_general' function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Seperate the function into two halves: first gather data from the packet,
next report all gathered data. The input subsystem should automatically
mute any events that aren't actually declared for the tablet at hand.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Begin slimming down the body of 'wacom_intuos_irq' by moving out its
largest block of code to a dedicated 'wacom_intuos_pad' function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
as reported by https://bugzilla.kernel.org/show_bug.cgi?id=108481
This bug reports mentions 6d4f5440 ("HID: multitouch: Fetch feature
reports on demand for Win8 devices") as the origin of the problem but this
commit actually masked 2 firmware bugs that are annihilating each other:
The report descriptor declares two features in reports 3 and 5:
0x05, 0x0d, // Usage Page (Digitizers) 318
0x09, 0x0e, // Usage (Device Configuration) 320
0xa1, 0x01, // Collection (Application) 322
0x85, 0x03, // Report ID (3) 324
0x09, 0x22, // Usage (Finger) 326
0xa1, 0x00, // Collection (Physical) 328
0x09, 0x52, // Usage (Inputmode) 330
0x15, 0x00, // Logical Minimum (0) 332
0x25, 0x0a, // Logical Maximum (10) 334
0x75, 0x08, // Report Size (8) 336
0x95, 0x02, // Report Count (2) 338
0xb1, 0x02, // Feature (Data,Var,Abs) 340
0xc0, // End Collection 342
0x09, 0x22, // Usage (Finger) 343
0xa1, 0x00, // Collection (Physical) 345
0x85, 0x05, // Report ID (5) 347
0x09, 0x57, // Usage (Surface Switch) 349
0x09, 0x58, // Usage (Button Switch) 351
0x15, 0x00, // Logical Minimum (0) 353
0x75, 0x01, // Report Size (1) 355
0x95, 0x02, // Report Count (2) 357
0x25, 0x03, // Logical Maximum (3) 359
0xb1, 0x02, // Feature (Data,Var,Abs) 361
0x95, 0x0e, // Report Count (14) 363
0xb1, 0x03, // Feature (Cnst,Var,Abs) 365
0xc0, // End Collection 367
The report ID 3 presents 2 input mode features, while only the first one
is handled by the device. Given that we did not checked if one was
previously assigned, we were dealing with the ignored featured and we
should never have been able to switch this panel into the multitouch mode.
However, the firmware presents an other bugs which allowed 6d4f5440
to counteract the faulty report descriptor. When we request the values
of the feature 5, the firmware answers "03 03 00". The fields are correct
but the report id is wrong. Before 6d4f5440, we retrieved all the features
and injected them in the system. So when we called report 5, we injected
in the system the report 3 with the values "03 00".
Setting the second input mode to 03 in this report changed it to "03 03"
and the touchpad switched to the mt mode. We could have set anything
in the second field because the actual value (the first 03 in this report)
was given by the query of report ID 5.
To sum up: 2 bugs in the firmware were hiding that we were accessing the
wrong feature.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Looks like 29fae1c85 ("HID: logitech: Add support for G29") was a little
bit aggressive and broke other devices.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=108121
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use
this quirk for all devices from this vendor, rather than maintaining a
list of all its known product IDs.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The critical section protected by usbhid->lock in hid_ctrl() is too
big and because of this it causes a recursive deadlock. "Too big" means
the case statement and the call to hid_input_report() do not need to be
protected by the spinlock (no URB operations are done inside them).
The deadlock happens because in certain rare cases drivers try to grab
the lock while handling the ctrl irq which grabs the lock before them
as described above. For example newer wacom tablets like 056a:033c try
to reschedule proximity reads from wacom_intuos_schedule_prox_event()
calling hid_hw_request() -> usbhid_request() -> usbhid_submit_report()
which tries to grab the usbhid lock already held by hid_ctrl().
There are two ways to get out of this deadlock:
1. Make the drivers work "around" the ctrl critical region, in the
wacom case for ex. by delaying the scheduling of the proximity read
request itself to a workqueue.
2. Shrink the critical region so the usbhid lock protects only the
instructions which modify usbhid state, calling hid_input_report()
with the spinlock unlocked, allowing the device driver to grab the
lock first, finish and then grab the lock afterwards in hid_ctrl().
This patch implements the 2nd solution.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The code in hid_debug_event() causes horrible code generation. First,
we do a strlen() call for every byte we copy (we're doing a store to
global memory, so gcc has no way of proving that strlen(buf) doesn't
change). Second, since both i, list->tail and HID_DEBUG_BUFSIZE have
signed type, the modulo computation has to take into account the
possibility that list->tail+i is negative, so it's not just a simple
and.
Fix the former by simply not doing strlen() at all (we have to load
buf[i] anyway, so testing it is almost free) and the latter by
changing i to unsigned. This cuts 29% (69 bytes) of the size of the
function.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The usage Confidence is mandary to Windows Precision Touchpad devices. The
appearance of this usage is checked in hidinput_connect but the quirk
MT_QUIRK_VALID_IS_CONFIDENCE is not applied to device accordingly.
Apply this quirk and also remove quirk MT_QUIRK_ALWAYS_VALID to enable palm
rejection for the WIN 8 touchpad devices which have implemented usage
Confidence in its input reports.
Tested on Dell XPS 13 laptop.
Signed-off-by: Allen Hung <allen_hung@dell.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If an event is discarded the device stays idle. Just reverse the order of
check and marking busy.
Found by code inspection.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
scnprintf() exists to provide these semantics, so we might as well use
it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Ensure that the G920 is not given the default deadzones.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Logitech G920 uses a couple of vendor specific usage pages,
which results in incorrect number of axis/buttons being detected.
This patch adds these pages to the 'ignore' list.
Reported-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The G920 can adjust the amount of 'turn' it permits, this patch adds
a sysfs file 'range' to control this.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch adds basic support for the Logitech G920 wheel when in HID
mode. This wheel 'speaks' the HID++ protocol, and therefor is driven
with hid-logitech-hidpp.
At this stage the driver only shows that it can communicate with the
wheel by outputting the name discovered over HID++.
The normal HID functions work to give input functionality using
joystick/event interface.
Note: in 'hidpp_probe()' we have to start the hardware to get packets
flowing, the same might apply in future for other devices which don't
use the unifying protocol.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Patch add support for the 'very long' HID++ packets, which are
64 bytes in length.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Without quirk keyboard repeats '6' until volume control is used since it
indicates the key is pressed without ever releasing.
Signed-off-by: Jimmy Berry <jimmy@boombatower.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Currently the sysfs report_descriptor attribute is only available if the device
is claimed. We have the descriptor before we even create the device node, so
just instantiate report_descriptor statically.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The kobject_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Sony has modified the HID descriptor in new revisions of the Dualshock 4 which
causes the size check in the descriptor replacement function to fail. Remove it
so that new revisions of the controller will work correctly.
The module is completely replacing the descriptor instead of patching it, so the
size check isn't really necessary anyways.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
On hardware which provides standby power for charging devices the state of the
LEDs and force-feedback on controllers can persist even when the system is in
standby. Additionally, the state of the controllers on resume may be different
from the state they were in at the time when they were suspended (ie. LEDs are
cleared on resume).
This implements the suspend and resume callbacks which saves and clears the
state of the LEDs on suspend and restores them on resume. Force-feedback is
stopped on suspend but not automatically restored on resume until a new event is
received to avoid potentially damaging hardware.
USB Sixaxis and navigation controllers must be reinitialized when the hardware
is reset on resume or they won't send any input reports.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Refactor the output report sending functions to allow for the sending of output
reports without enqueuing a work item. Output reports for any device can now be
sent via the send_output_report function pointer in the sony_sc struct which
points to the appropriate output function. The individual state worker
functions have been replaced with a universal sony_state_worker function which
uses this function pointer.
Signed-off-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
